FPV Quad Parts

Peripherals and Replacement Parts

Equipment

Equipment Peripherals

Build Page Parts

Build Parts Equipment

Pre-Built Quads and Kits 

Build Page Parts Overflow

Build Parts Equipment Overflow

Compatibility Categories

BetaFPV

BetaFPV BNF Meteor75 Brushless Whoop

BETAFPV

All products containing batteries must be shipped by a ground shipping method.
Want a 1S whoop for outdoor, around the house and the yard? Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022). The canopy has a special design and high-quality C03 FPV camera combined with 0802SE 19500KV motors make it perfectly balanced in all areas of performance.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!
Features

Meteor75 is the first generation whoop powered by a brand-new BT2.0 connector 450mAh battery. The BT2.0 connector effectively decreases internal connector resistance for a much better discharge performance compared with the initial PH2.0 connector
The power system uses the latest 0802SE 19500KV motors and 40mm 2-blade props, which provides pilots a powerful indoor and outdoor flight.
Built-in 1.45g ultralight weight and upgraded C03 FPV camera. This new camera has optimal performance for indoor whoop drones.
Adopt with injection molding technique, this canopy is 1.60g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
Reserve two UART ports on F4 1S 5A FC (SPI Frsky) board.
The various colors of the spare parts including the 75mm frame and micro canopy, offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.


BT2.0 Connector
BETAFPV has exclusively designed BT2.0 connector has broken through the bottle-neck of PH2.0 connector. There is a graph of comparison between BT2.0 connector 1S 450mAh battery and Emax 1S 450mAh battery. The discharge current is 11A in this testing. You could see that it has a longer time and improvement in voltage sag with BT2.0 connector, which brings better flight performance.

Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP and can be switched to Futaba SFHSS protocol through Betaflight configurator. The ESC on the new board powered by BB51 hardware in place of BB21 comes with Bluejay 96k ESC firmware, allowing 0802SE 19500KV motors to give full play to the efficiency of power. We update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.
Meteor75: (Frsky)
FC Inside:F4 1S 5A FC (SPI Frsky)Gyro: BMI270FC Firmware: BETAFPVF411RXUART Port: Two UART PortsExternal RX: Supported
C03 Camera
C03 FPV Micro Camera is 1.45g ultralight weight and a great camera for indoor micro FPV quadcopters. It features a 1200TVL definition with 1/3" CMOS sensor, 2.1mm lens for 160° FOV, and excellent latency, which boasts high-quality, clear and sharper images through your goggles.

Motors
0802SE 19500KV Motor motor is a lightweight 1S motor, compared with the 0802 series brushless motors, it is not only significantly reduced the weight to only 1.88g/pc but ensures excellent performance of power and thrust. It makes the perfect dynamic balance, which gives the drone more flexibility and longer flying time.
 

Frame
This frame is ultralight at only 5.68g and still durable. The battery slot is closer to the center of gravity for a smoother flying experience, and you will land on the motor screws instead of the battery. BETAFPV offers various colors of Meteor75 frames for options, making DIY easier.

Specifications

Item: Meteor75 Brushless Whoop Quadcopter (2022)
FC&ampESC:F4 1S 5A FC (SPI Frsky)
Frame: Meteor75 Frame
Motors: 0802SE Brushless Motor
Props: 40mm 2-Blade Propellers (1.0mm Shaft)
Camera: C03 FPV Camera
Tilt: 30° (default)/20° (optional)
Canopy: Canopy for Micro Camera 2022 version
Receiver Option: Frsky
VTX: M03 25-350mW VTX
Battery: BT2.0 450mAh 1S 30C Battery
Flight time: 6 mins (stable flying) / 4.5 mins (acro flying)
Weight: 24.98g

Includes

1x BetaFPV Meteor75 Whoop Quadcopter (2022) - FRSKY
2x 450mAh 1S 30C Battery with BT2.0 connector
1x BT2.0 Battery Charger and Voltage Tester
1x TypeC USB cable
1x Customized Carry Case
1x Spare 40mm 2-Blade props (1.0mm Shaft)
1x Screwdriver
3x Decorative Parts
1x 20° Lens Camera Mount for C03 Camera
1x 30° Lens Camera Mount for C02 Camera
1x Pack of Screws



All products containing batteries must be shipped by a ground shipping method. Want a 1S whoop for outdoor, around the house and the yard? Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022). The canopy has a special design and high-qua

BetaFPV BNF Meteor75 1S Analog Whoop (2022) - FRSKY


Stepping into HD world with 1S whoop quadcopter! The classical Meteor75 Brushless Whoop Quadcopter comes with Walksnail Avatar Mini HD VTX or HDZero Whoop Lite Bundle, bringing conspicuous images and exceptional visuals to your eyes and capturing details that make the footage look as exciting as the flight. Together with 1102 18000KV motors that feature strong propulsion, it gives pilots powerful and impressive results. Enjoy an immersive flight experience, and get the perfect shots with the new HD VTX system indoors and outdoors.

Tons of ExpressLRS items are available now!
Recommend the newest BT2.0 550mAh 1S Battery. More flight time and higher discharge rate.

Bullet Points

Powerful propulsion capabilities combined with Walksnail HD VTX or HDZero VTX give pilots an immersive flight experience and impactful visuals.
Ultralight weight for 40.5g (Walksnail)/ 36.4g (HDZero). With BT2.0 connector, it effectively decreases internal connector resistance for good conductive performance.

Equipped with 40mm 3-blade props and upgraded 1102 18000KV motors. The upgraded motors not only take abilities as good as before to provide strong propulsion in 1S whoop drone but also come with a new look. And simultaneously its black and red motor bell fully matches the Meteror75 frame.

Reserve two UART ports on F4 1S 5A FC(SPI Frsky) V3.0 board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it.
F4 1S 5A FC (Serial ELRS 2.4G) V2.0 is flexible in upgrading and has great potential. It supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware.


Specification

Item: Meteor75 Brushless Whoop Quadcopter (1S HD Digital VTX)
Flight Time: 3.5 mins (HDZero)/3 mins (Walksnail)
Camera Adjustable Angle: 0-45°
Motors: 1102 18000KV Motor

Battery: BT2.0 450mAh 1S 30C Battery

Frame: Meteor75 Micro Brushless Whoop Frame

Propellers: 40mm 3-Blade Propellers (1.5mm Shaft)

Weight Without Battery: 40.5g (Walksnail)/36.4g (HDZero)
Receiver: Serial ELRS 2.4G/SPI Frsky/TBS
FC&ampESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0
VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero)
VTX: 1S Walksnail Avatar Mini HD VTX/HDZero Whoop Lite Bundle
Camera: Wanlksnail Avatar Nano Camera/HDZero Nano Lite Camera


Note: F4 1S 5A FC (Serial ELRS 2.4G) V2.0 does not support external receivers. F4 1S 5A FC (SPI Frsky) V3.0 is available to connect an external receiver and can be used as PNP. Please make sure that the battery voltage must be 3V at least when flying, otherwise, the HD digital VTX would stop working. 
HD Digital VTX System
There are two HD versions to choose from. Based on Walksnail Avatar, the Walksnail Avatar Mini HD VTX also uses H.265 high-efficiency video coding, an industry-leading technology, providing 1080P/60FPS image recording with 22ms ultra-low latency. It is specially designed for 3.1-5V power input and 10g lightweight, which is compatible with 1S whoop drone. Build-in 8 GB storage, the Avatar Mini HD VTX has the capability of recording HD video without interference from capacity and exporting video by USB cable. Besides, with Canvas Mode on Avatar Mini HD VTX, Betaflight full OSD display is supported and can be adjusted easily by remote control.

HDZero Nano Lite Camera is designed for feather-lite drones where every gram counts. At a weight as low as 1.5g, combined with the new Whoop Lite VTX at 4.5g with 0.4g dipole antenna enables a world’s-first production digital FPV solution of about 7g. The HDZero Whoop lite Bundle supports 1-3S power input with 25mW/200mW RF power and is capable of recording in 720P/60FPS with super low latency of less than 19ms. What's more, pilots can activate and configure its OSD function on Betaflight Configurator.

Injection Molded Canopy for HD Camera
Micro Canopy for HD Camera is specially designed to be compatible with Walksnail or HDZero HD digital VTX and has an adjustable camera lens of 0-45°. With the injection molding technique, the canopy is very durable and flexible for crash resistant. Besides, the hollow-out design not only reduces the influence of heat on electronic parts but also is available to be armed with decorative parts we prepared.

New 1102 18000KV Motors
1102 18000KV motors have a great balance between weight and power on 75mm 1S whoop drones. Only 2.9g with connectors. With the high 18000KV, it could have a great punch power even with only 1S battery. Also, it adopts a PCB connector to allow you to repair it easier once cables are disconnected.

Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75 HD. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. The ESC on the new board is powered by BB51 hardware in place of BB21. Last but not least, we update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.





Meteor75 HD (ELRS)

Meteor75 HD (Frsky, PNP, TBS)


FC Inside
F4 1S 5A FC (Serial ELRS 2.4G) V2.0
F4 1S 5A FC (SPI Frsky) V3.0


Gyro
BMI270
BMI270


FC Firmware
BETAFPVF411
BETAFPVF411RX


UART Port
One UART Port
Two UART Ports


External RX
Not Supported
Supported



Note: Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware and CLI dump file. If you update the 4.3.1 firmware from Betaflight official site, please flash the CLI dump file for Meteor75 HD.
Download the FC firmware and CLI dump file for Walksnail and HDZero version.
Recommended Parts

Radio Transmitter: LiteRadio 3 Pro, LiteRadio 3, LiteRadio 2 SE
Battery: BT2.0 450mAh 1S 30C Battery, BT2.0 550mAh 1S Battery
Props: 40mm 3-Blade Propellers (1.5mm Shaft)
Colorful Frame: Meteor75 Micro Brushless Whoop Frame

Colorful Canopy: Micro Canopy for HD Camera

Sticker: BETAFPV Waterslide Decals

Charger: 6 Ports 1S Battery Charger &amp Adapter

Screws: Meteor Series Motor Fixing Screws Pack (40PCS)

BT2.0 Series Accessories

FAQ

Pilots can read and export the recording videos from Walksnail VTX by a 4-pin connector. Below is the diagram picture. For more information, please refer to the manual for it.



Click to download the manual for Walksnail Avatar Mini VTX.
Click to download the manual for HDZero Whoop Lite Bundle.

Package

1 * Meteor75 Brushless Whoop Quadcopter (Walksnail or HDZero HD Digital VTX)
2 * 450mAh 1S 30C Battery with BT2.0 Connector
1 * Type-C USB Cable
1 * BT2.0 Battery Charger and Voltage Tester
4 * 40mm 3-Blade Props (1.5mm Shaft)
1 * Screwdriver
1 * Walksnail VTX USB Cable (For Walksnail Version)
1 * HDZero VTX USB Cable (For HDZero Version)
1 * Pack of Screws

Note: The propellers in the package were modified from three holes to one hole.



Stepping into HD world with 1S whoop quadcopter! The classical Meteor75 Brushless Whoop Quadcopter comes with Walksnail Avatar Mini HD VTX or HDZero Whoop Lite Bundle, bringing conspicuous images and exceptional visuals to your eyes and capturing details that make the footage look as exciting as the flight. Together wi

Meteor75 Brushless Whoop Quadcopter (1S HD Digital VTX)

BetaFPV Meteor75 1S Walksnail Digital VTX Brushless Whoop Quadcopter - Choose Receiver

All products containing batteries must be shipped by a ground shipping method.
Want a 1S whoop for outdoor, around the house and the yard? Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022). The canopy has a special design and high-quality C03 FPV camera combined with 0802SE 19500KV motors make it perfectly balanced in all areas of performance.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!
Features

Meteor75 is the first generation whoop powered by a brand-new BT2.0 connector 450mAh battery. The BT2.0 connector effectively decreases internal connector resistance for a much better discharge performance compared with the initial PH2.0 connector
The power system uses the latest 0802SE 19500KV motors and 40mm 2-blade props, which provides pilots a powerful indoor and outdoor flight.
Built-in 1.45g ultralight weight and upgraded C03 FPV camera. This new camera has optimal performance for indoor whoop drones.
Adopt with injection molding technique, this canopy is 1.60g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
Reserve two UART ports on F4 1S 5A FC (SPI Frsky) board.
The various colors of the spare parts including the 75mm frame and micro canopy, offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.


BT2.0 Connector
BETAFPV has exclusively designed BT2.0 connector has broken through the bottle-neck of PH2.0 connector. There is a graph of comparison between BT2.0 connector 1S 450mAh battery and Emax 1S 450mAh battery. The discharge current is 11A in this testing. You could see that it has a longer time and improvement in voltage sag with BT2.0 connector, which brings better flight performance.

Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP and can be switched to Futaba SFHSS protocol through Betaflight configurator. The ESC on the new board powered by BB51 hardware in place of BB21 comes with Bluejay 96k ESC firmware, allowing 0802SE 19500KV motors to give full play to the efficiency of power. We update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.
Meteor75: (Frsky)
FC Inside:F4 1S 5A FC (SPI Frsky)Gyro: BMI270FC Firmware: BETAFPVF411RXUART Port: Two UART PortsExternal RX: Supported
C03 Camera
C03 FPV Micro Camera is 1.45g ultralight weight and a great camera for indoor micro FPV quadcopters. It features a 1200TVL definition with 1/3&quot CMOS sensor, 2.1mm lens for 160° FOV, and excellent latency, which boasts high-quality, clear and sharper images through your goggles.

Motors
0802SE 19500KV Motor motor is a lightweight 1S motor, compared with the 0802 series brushless motors, it is not only significantly reduced the weight to only 1.88g/pc but ensures excellent performance of power and thrust. It makes the perfect dynamic balance, which gives the drone more flexibility and longer flying time.
 

Frame
This frame is ultralight at only 5.68g and still durable. The battery slot is closer to the center of gravity for a smoother flying experience, and you will land on the motor screws instead of the battery. BETAFPV offers various colors of Meteor75 frames for options, making DIY easier.

Specifications

Item: Meteor75 Brushless Whoop Quadcopter (2022)
FC&ampampESC:F4 1S 5A FC (SPI Frsky)
Frame: Meteor75 Frame
Motors: 0802SE Brushless Motor
Props: 40mm 2-Blade Propellers (1.0mm Shaft)
Camera: C03 FPV Camera
Tilt: 30° (default)/20° (optional)
Canopy: Canopy for Micro Camera 2022 version
Receiver Option: Frsky
VTX: M03 25-350mW VTX
Battery: BT2.0 450mAh 1S 30C Battery
Flight time: 6 mins (stable flying) / 4.5 mins (acro flying)
Weight: 24.98g

Includes

1x BetaFPV Meteor75 Whoop Quadcopter (2022) - FRSKY
2x 450mAh 1S 30C Battery with BT2.0 connector
1x BT2.0 Battery Charger and Voltage Tester
1x TypeC USB cable
1x Customized Carry Case
1x Spare 40mm 2-Blade props (1.0mm Shaft)
1x Screwdriver
3x Decorative Parts
1x 20° Lens Camera Mount for C03 Camera
1x 30° Lens Camera Mount for C02 Camera
1x Pack of Screws



BetaFPV BNF Meteor75 1S Analog Whoop (2022) - FRSKY from WREKD Co.

Meteor75, a better approach to the 75mm micro drone which features high KV motors - 1102 18000KV motors & BT2.0 450mAH battery, giving pilots plenty of power to use both indoor and outdoor spaces as a small scale acro playground.

BetaFPV Meteor75 1S Brushless Whoop Quadcopter

The classical Meteor75 Brushless Whoop Quadcopter comes with Walksnail Avatar Mini HD VTX bringing conspicuous images and exceptional visuals to your eyes and capturing details that make the footage look as exciting as the flight.

BetaFPV Meteor75 1S Brushless Whoop HD w/ Walksnail Avatar Mini VTX

The classical Meteor75 Brushless Whoop Quadcopter comes with HDZero Lite VTX bringing conspicuous images and exceptional visuals to your eyes and capturing details that make the footage look as exciting as the flight.

BetaFPV Meteor75 1S Brushless Whoop HD w/ HDZero 

All PRE-ORDERS shipping ASAP!!! All products with batteries must be shipped by a ground shipping method.
Want a 1S whoop for outdoor, around the house and yard? The Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022), supporting serial ExpressLRS 2.4G, Frsky, or TBS RX for options. The new canopy with special style and high-quality C03 FPV camera combined with 0802SE 19500KV motors make it perfectly balanced in all areas of performance.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!

Features

The Meteor75 is the first generation whoop powered by a brand-new BT2.0 connector 450mAh battery. The BT2.0 connector effectively decreases internal connector resistance for a much better discharge performance compared with the initial PH2.0 connector.
The power system uses the latest 0802SE 19500KV motors and 40mm 2-blade props, which provides pilots a stronger experience of a powerful indoor and outdoor flight
Built-in 1.52g ultralight weight and upgraded C03 FPV camera. This new camera has optimal performance for indoor whoop drones.
Adopted with an injection molding technique, this canopy is 1.60g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
Reserved two UART ports on F4 1S 5A FC (SPI Frsky) board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it.
F4 1S 5A FC (Serial ELRS 2.4G) is flexible in upgrading and has great potential. It supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware.
The various colors of the spare parts including the 75mm frame and micro canopy, offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.

BETAFPV Meteor Series
This is the new Meteor75 Analog VTX version with a new micro canopy, built-in serial ExpressLRS 2.4G instead of SPI ERLS 2.4G, and the new C03 FPV camera that ensures a high-quality and clear image. For pilots who want to fly 1S HD whoop drone, Meteor75 HD digital VTX is a good choice.



 
Meteor75 (2022)
Meteor75 (2021)
Meteor75 1S HD


FC&ampESC
F4 1S 5A FC (2022)
F4 1S 5A FC
F4 1S 5A FC (2022)


RX
Serial ELRS, SPI FrSky/PNP, TBS
SPI ELRS, SPI FrSky, TBS
Serial ELRS, SPI FrSky/PNP, TBS


Camera
C03 FPV Camera
C02 FPV Camera
Walksnail/HDZero Camera


VTX
M03 Analog VTX
M03 Analog VTX
Walksnail Avatar or HD Zero Lite


Motors
0802SE 19500Kv Motor
1102 18000Kv or 0802SE 19500Kv Motors
1102 18000Kv Motors


Props
40mm 2-blade
40mm 3-blade, or 40mm 2-blade
40mm 3-blade


Canopy
New Micro Canopy (2022)
Micro Canopy
Micro Canopy for HD


Tilt
20° or 30°

30°

0-45°



Flight Time
6 mins (stable flying)
3-4 mins
3.5 mins (HDZero) or 3 mins (Walksnail)



 
BETAFPV upgraded all Meteor Series quadcopters like Meteor65, Meteor65 Pro, Meteor 75, and Meteor85 whoop quadcopters, through the new flight controller, motors, camera, frame, canopy, etc, to provide the best whoop quadcopters for pilots.
BT2.0 Connector
BETAFPV exclusive designed BT2.0 connector has broken through the bottle-neck of the PH2.0 connector. There is a graph comparing between BT2.0 connector 1S 450mAh battery and the Emax 1S 450mAh battery. The discharge current is 11A in this testing. You could see that it has a long time and improvement in voltage sag with a BT2.0 connector, which brings better flight performance.

Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP and can be switched to Futaba SFHSS protocol through Betaflight configurator. The ESC on the new board powered by BB51 hardware in place of BB21 comes with Bluejay 96k ESC firmware, allowing 0802SE 19500KV motors to give full play to the efficiency of power. We update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.



 
Meteor75 (ELRS)
Meteor75 (FrSky, PNP, TBS)


FC Inside
F4 1S 5A FC (Serial ELRS 2.4GHz)
F4 1S 5A FC (SPI FrSky)


Gyro
BMI270
BMI270


FC Firmware
BETAFPVF411
BETAFPVF411RX


UART Port
One UART Port
Two UART Port


External RX
Not Supported
Supported



 
Note: For F4 1S 5A FC (serial ELRS 2.4G), ONLY Betaflight firmware 4.3.0 and up start to support BMI270 gyro. For F4 1S 5A FC (SPI Frsky), we recommend using BETAFPVF411RX 4.2.11 firmware and CLI dump file offered by BETAFPV. If you update the 4.3.0 and up firmware for serial ELRS 2.4G from the Betaflight official site, please flash the CLI dump file for Meteor75.
Download the FC firmware and CLI dump file for Meteor 75 ELRS2.4G, Frsky, or TBS.

C03 Camera
C03 FPV Micro Camera is 1.52g ultralight weight and a great camera for indoor micro FPV quadcopters. It features a 1200TVL definition with 1/3" CMOS sensor, 2.1mm lens for 160° FOV, and excellent latency, which boasts high-quality, clear and sharper images through your goggles.

Motors
0802SE 19500KV Motor motor is a lightweight 1S motor, compared with the 0802 series brushless motors, it is not only significantly reduced the weight which is only 1.88g/pc but also ensures excellent performance of power and thrust. It makes the perfect dynamic balance, which gives the drone more flexibility and longer flying time.

Frame
This frame is ultralight only 5.68g and durable enough. The battery slot is closer to the center of gravity for a smoother flying experience, and you will land on the motor screws instead of the battery. BETAFPV offers various colors of Meteor75 frames for options, making DIY easier.

Specification

Item: Meteor75 Brushless Whoop Quadcopter (2022)
FC&ampESC: F4 1S 5A FC (Serial ELRS 2.4G)/F4 1S 5A FC (SPI Frsky)
Frame: Meteor75 Frame
Motors: 0802SE 19500KV Motor
Props: 40mm 2-Blade Propellers (1.0mm Shaft)
Camera: C03 FPV Camera
Tilt: 30° (default)/20° (optional)
Canopy: Canopy for Micro Camera 2022 version
Receiver Option: ELRS2.4G, Frsky/PNP, TBS Crossfire
VTX: M03 25-350mW VTX
Battery: BT2.0 450mAh 1S 30C Battery
Flight time: 6 mins (stable flying) / 4.5 mins (acro flying)
Weight: 24.98g

Includes

1x Meteor75 Brushless Whoop Quadcopter (1S)
2x 450mAh 1S 30C Battery with BT2.0 connector
1x BT2.0 Battery Charger and Voltage Tester
1x TypeC USB cable
1x Customized Carry Case
1x Spare 40mm 2-Blade props (1.0mm Shaft)
1x Screwdriver
3x Decorative Parts
1x 20° Lens Camera Mount for C03 Camera
1x 30° Lens Camera Mount for C02 Camera

FAQ

Download the FC firmware and CLI dump file for Meteor75.

ExpressLRS is the most popular radio link in 2021. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. Know more about the ExpressLRS project on Github or join the discussion in the Facebook Group.



All PRE-ORDERS shipping ASAP!!! All products with batteries must be shipped by a ground shipping method. Want a 1S whoop for outdoor, around the house and yard? The Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022), supporting serial 

(PRE-ORDER) BetaFPV BNF Meteor75 1S Brushless Analog Whoop (BT2.0) - ELRS 2.4 GHz

(PRE-ORDER) BetaFPV BNF Meteor75 1S Brushless Analog Whoop (BT2.0) - E

Pre-Built Quad Kit Type

Pre-Built Quads and Kits

Quad Frame Size

Quad Type

Happymodel

Happymodel BNF Mobeetle6 65mm 2-in-1 Whoop

The Happymodel Mobeetle6 BNF is the next innovation in the micro whoop and toothpick drone community! The Mobeetle frame is easily converted from whoop to drone with the included frame parts and race canopy.

Happymodel Mobeetle6 1S 65mm 2-in-1 Whoop Drone

Happymodel BNF Mobula 7 Whoop

HAPPYMODEL

Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1S Will be the best choice in the whoop season.  This is an amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX ranges by using this flight controller. The new RS0802 motors come with a new unibell design, uses a 1.5mm shaft, and includes a PCB bottom plate, which means high efficiency, and much more reliability.
Check out the rest of pre-built quads and our HappyModel selection!
Features

X12 5-IN-1 AIO flight controller w/ built-in receiver and OpenVTX
VTX Power up to 400mw
RS0802 20000KV motors
RunCam Nano 3. The lightest 1/3 CMOS 800TVL Camera
Smooth and powerful
Compatible with 1S Lipo/LIHV

Specifications

Input Voltage: 1S
Max Continuous Current: 12A
Motors: 0802 20000KV
Camera: RunCam Nano 3
Wheelbase: 75mm
Dimensions: 99x99x40mm
Weight: 24g

Includes

1x HappyModel BNF 1S Mobula 7 Whoop



The all-new HappyModel BNF 1S Mobula 7 Whoop features the latest parts to bring you a fun, exciting whoop to fly. Get it shipped fast and free from RDQ!

HappyModel BNF 1S Mobula7 Analog Whoop - Choose Receiver Type

HappyModel BNF 1S Mobula 7 Whoop for Sale - RaceDayQuads

This&nbspHappymodel Mobula7&nbspis a 1S micro whoop with a RunCam Nano 3 Camera. This whoop features the first 5-in-1 AIO with three different receiver options and 0802 20000KV motors with a unibell design.

This Happymodel Mobula7 is a 1S micro whoop with a RunCam Nano 3 Camera. This whoop features the first 5-in-1 AIO with three different receiver options and 0802 20000KV motors with a unibell design.

Happymodel Mobula7 1S 75mm Analog Whoop

We’re glad to launched our new Mobula7 drone , this time the 75mm whoop based on 1s power. Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1s Will be the best choice in the whoop season. The world first 5-IN-1 AIO flight controller with ExpressLRS 2.0 , OPENV

Happymodel Mobula7 1s 75mm Analog FPV Brushless Whoop Drone - Choose Receiver

HappyModel

Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1S Will be the best choice in the whoop season.  This is an amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX ranges by using this flight controller. The new RS0802 motors come

HappyModel BNF 1S Mobula7 Analog Whoop - Choose Receiver Type from WREKD Co.

iFlight

iFlight BNF Alpha A65 65mm Brushless Whoop

The&nbspiFlight&nbspAlpha A65 V2&nbspis an even smaller size 65mm lightweight 24.5g whoop. This version features an updated canopy, frame, motors, AIO Board, and camera.

The iFlight Alpha A65 V2 is an even smaller size 65mm lightweight 24.5g whoop. This version features an updated canopy, frame, motors, AIO Board, and camera.

iFlight Alpha A65 Drone - Analog - V2 

EMAX

EMAX RTF EZ Pilot Pro Kit - Goggles, Radio Transmitter, 75mm Whoop

Consistent improvement is the goal of our team at EMAX but this comes at a cost. With more upgrades to our micro indoor racing drones which cater to more experienced pilots, we further alienate potential budding pilots looking to explore the world of FPV. This is why our engineers have come up with a solution through t

EMAX EZ Pilot Pro Indoor Racing Drone - RTF

Emax USA

 

 
 
 
Drone Specs:

Wheelbase: 75mm
Dry weight: 32.5g
AIO: MATEKF411 FC w/ 6A ESC and  25/100/200mw switchable video transmitter
Motor: 08025 II KV15000
RX Protocol: FrSky D8 SPI

Includes:

1x EZ Pilot Pro Drone
1x E8 Transmitter
1x Transporter 2 Non-DVR Version
1x Monitor Mounting Hardware
1x EMAX 1S 450 mAh LiPo battery
1x 6-Port 1S USB LiPo Battery Charger
1x USB Cable for Charging + Programming
1x Set Spare Turtlemode Propellers
1x Set Spare Hardware

        Drone Specs: Wheelbase: 75mm Dry weight: 32.5g AIO: MATEKF411 FC w/ 6A ESC and  25/100/200mw switchable video transmitter Motor: 08025 II KV15000 RX Protocol: FrSky D8 SPI Includes: 1x EZ Pilot Pro Drone 1x E8 Transmitter 1x Transporter 2 Non-DVR Version 1x Monitor Mounting Hardware 1x EMAX 1S 450 mAh LiPo batt

EZ Pilot Pro Ready-To-Fly RTF FPV Drone w/ Controller & Goggles from WREKD Co.

EZ Pilot Pro Ready-To-Fly RTF FPV Drone w/ Controller & Goggles

The EZ Pilot Pro drone features an improved frame, 200mw VTX capabilities, and a solid pin PH2.0 connector over the original.

EMAX EZ Pilot Pro Beginner FPV Drone RTF Kit w/ Transporter 2 Goggles + E8 Transmitter

Happymodel BNF Mobula 6 Micro Whoop

The Mobula6 Micro FPV Whoop features the Runcam Nano3, Onboard Frsky Receiver, 5A BLheli_S 4-in-1 ESC, and more! This mini and lightweight whoop (65mm) will take you hard-to-get places!
Pick a motor: Race (25000Kv) or Standard (19000Kv).
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Features

AIO 4IN1 Crazybee F4 Lite flight controller built-in 5.8G VTX
Extreme light 1S 65mm Brushless whoop only 20g
Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
Smooth and powerful
Compatible with 1S Lipo/LIHV
Camera Angle adjustable

Specifications

Brand Name: Happymodel
Item Name: Mobula6 1S 65mm Brushless whoop drone BNF version
Wheelbase: 65mm
Size: 80mmx80mmx37mm
Weight: 20g
Receiver option:
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Motor speed option:
SE0802 KV25000(Race Edition)
SE0802 KV19000(Regular Edition)

Motors

Model: SE0802 19000KV or KV25000
Configuration:9N12P
Stator Diameter:8mm
Stator Length:2mm
Shaft Diameter: Φ1mm
Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm
Weight(g):1.9g
No.of Cells(Lipo):1S only

Propellers

Gemfan 1219-3
Center Thickness:5mm
Prop Disk Diameter:31mm
Center Hole Inner diameter:1.0mm
Weight:0.28g

Flight controller

(Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM42688P
Board size: 28.5x28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/Flysky receiver
Built-in 5V 1A BEC
Built-in voltage detection

Onboard 4in1 ESC

MCU upgraded to ICM42688P
Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600

Onboard Frsky SPI D8 receiver Version

SPI BUS receiver Frsky D8 compatible
Compatible Non-EU transmitter D8 modelChannels: 8ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m


Onboard 5.8g VTX

Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race bandSmartaudio ready

Runcam Nano3

Model: RunCam Nano 3
Image Sensor: 1/3″ CMOS
Horizontal Resolution: 800TVL
Lens : 2.1mm(M8) FOV 160°
Signal System: NTSC
S/N Ratio: &ampgt50dBElectronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power: DC 3-5.5V
Current: 110mA@5V 120mA@3.3V
Housing Material: ABS
Net Weight: 1.2g
Dimensions: L14mmxW14mmxH9mm

Lipo Battery

Capacity:300mAh
Voltage:3.8v
Continuous Discharge Rate: 30C
Size: 57mmx12mmx7mm
Weight: 8gConnector: PH2.0

Includes

1x Mobula6 1S 65mm whoop Drone Frame 
1x SPI Receiver: Crazybee F4 Lite FC built-in Frsky SPI D8 RX 
4x SE0802 KV19000 or KV25000 brushless motor 
1x Gemfan 1219-3 Propellers(4cw+4ccw) 
1x Runcam Nano3 1/3 CMOS 800TVL camera 
1x 5.8G 25mw 40ch VTX (Flight controller built-in) 
4x 1S 300mah 30C LiHV Battery 
1x 1S Lipo/LIHV USB Charger 
1x Propeller disassemble tool


The Mobula6 Micro FPV Whoop features the Runcam Nano3, Onboard Frsky Receiver, 5A BLheli_S 4-in-1 ESC, and more! This mini and lightweight whoop (65mm) will take you hard-to-get places! Pick a motor: Race (25000Kv) or Standard (19000Kv). Check out our other pre-built quads, as well as the rest of our HappyModel selecti

HappyModel BNF Mobula6 1S Analog Whoop (SPI FrSky) - Choose Kv from WREKD Co.

HappyModel BNF Mobula6 1S Analog Whoop (SPI FrSky) - Choose Kv

With one of the best (if not THE best) nano cameras the Runcam Nano3 and significantly lighter than its competitors Mobula 6 is a serious contender in the whoop racing scene.Available in 2 different KV options25000KV for crazy fast races19000KV for great all around performance and racing Check out our Mobula 6 and Part

HappyModel BNF Mobula 6 1S Micro Whoop Quadcopter (Choose RX & Version)

The Happymodel Mobula6 1S Whoop is a great racing FPV drone! The Mobula6 is a smooth and agile brushless drone that comes with the RunCam Nano 3, 0802 19000KV Motors, and many other cool features and specs that make this whoop a must-have! Now with Built-In ELRS Receivers!

The Happymodel Mobula6 1S Whoop is a great racing FPV drone! The Mobula6 is a smooth and agile brushless drone that comes with the RunCam Nano 3, 0802 19000KV Motors, and many other cool features and specs that make this whoop a must-have! Now with 

Happymodel Mobula6 1S 65mm Brushless Whoop w/ RunCam Nano 3 - ELRS

ExpressLRS is currently the most popular remote control link system. It has the characteristics of low latency and high packet rate, and its link quality is very reliable. Now we are about to release Mobula6 equipped with ExpressLRS RC link system, the new Mobula6 elrs would coming out with a new 0802 brushless motor, 

Happymodel Mobula6 ELRS 2.4GHz 1s 65mm Brushless FPV Brushless Whoop Drone - Choose Version

EMAX BNF TinyHawk III 76mm Whoop

EMAX Tinyhawk III FPV Racing Drone - FrSky Bind N Fly (BNF)

The best quality First Person View equipment. Free or discounted shipping on all orders.Drone Racing, RC Airplanes, FPV Cameras, FPV Goggles, Video Transmitters, RC Quads, Drone Antennas, Lipo Batteries, and Ground Station Equipment.All available for amateurs, schools, hobbyists, government, and wholesale buyers.

EMAX Tinyhawk III FPV Racing Drone - FrSky Bind N Fly (BNF) - RMRC

Self-improvement is a core trait for the engineers at EMAX, which is why when approached about a new successor to the Tinyhawk series, they designed the Tinyhawk III to build upon all the strengths of previous generations while improving any shortcomings. First is a drastically redesigned body frame centered around dur

Emax Tinyhawk 3 FPV Racing Drone - FrSky Bind N Fly (BNF)

Introducing... the EMAX TinyHawk III BNF Quadcopter!! This BNF features the RunCam Nano 4 Camera.

EMAX TinyHawk III FPV Racing Drone BNF

        Size class: 76mm Weight (without battery): 32 grams Motors: TH0802 II 15000kv Flight Controller / ESC: F4 STM32 (MATEKF411RX), 1-2S Input, 5A 4-in-1 BLHeli_S ESC Receiver:  SPI / FrSky D8/D16 Camera: RunCam Nano 4 Video Transmitter: 25-100-200mw Switchable 37CH w/ Smart Audio.

Tinyhawk III FPV Racing Drone - FrSky Bind N Fly (BNF)

EMAX RTF TinyHawk III Ready to Fly Kit w/ Goggles, Radio Transmitter, Case and 76mm Racing Whoop Drone

EMAX Tinyhawk III FPV Racing Drone RTF with Controller/Goggles

EMAX Tinyhawk III FPV Racing Drone RTF with Controller/Goggl - RMRC

Emax Tinyhawk 3 FPV Racing Drone - Ready To Fly (RTF) w/ Controller and Goggles

      Size class: 76mm Weight (without battery): 32 grams Motors: TH0802 II 15000kv Flight Controller / ESC: F4 STM32 (MATEKF411RX), 1-2S Input, 5A 4-in-1 BLHeli_S ESC Receiver:  SPI / FrSky D8/D16 Camera: RunCam Nano 4 Video Transmitter: 25-100-200mw Switchable 37CH w/ Smart Audio.    

Tinyhawk III FPV Racing Drone - Ready To Fly (RTF) w/ Controller and Goggles

Introducing... the&nbspEMAX TinyHawk III RTF Bundle!! This bundle features the EMAX TinyHawk III Quadcopter, EMAX E8 Transmitter, EMAX Transporter 2 Goggles, and RunCam Nano 4 Camera!

Introducing... the EMAX TinyHawk III RTF Bundle!! This bundle features the EMAX TinyHawk III Quadcopter, EMAX E8 Transmitter, EMAX Transporter 2 Goggles, and RunCam Nano 4 Camera!

EMAX TinyHawk III FPV Racing Drone RTF Bundle

 

 
 
Size class: 76mm
Weight (without battery): 32 grams
Motors: TH0802 II 15000kv
Flight Controller / ESC: F4 STM32 (MATEKF411RX), 1-2S Input, 5A 4-in-1 BLHeli_S ESC
Receiver:  SPI / FrSky D8/D16
Camera: RunCam Nano 4
Video Transmitter: 25-100-200mw Switchable 37CH w/ Smart Audio.
 
 

Tinyhawk III FPV Racing Drone - Ready To Fly (RTF) w/ Controller and Goggles from WREKD Co.

BetaFPV RTF Cetus Pro FPV Kit - Cetus Pro Whoop, Goggles, Transmitter, Batteries, Charger & Case

The Cetus Pro FPV Kit is finally here! It is the best ideal choice for beginners to advance currently. Comes with a Cetus Pro brushless quadcopter, LiteRadio2 SE transmitter, and VR02 FPV Goggles, it's more powerful and maneuverable for all starters as well as FPV pros to practice indoor and outdoor. Check out all our 

BetaFPV Cetus PRO FPV RTF Kit W/Goggles & Controller

The Cetus Pro FPV Kit is finally here! It is the best ideal choice for beginners to advance currently. Comes with a Cetus Pro brushless quadcopter, LiteRadio2 SE transmitter, and VR02 FPV Goggles, it's more powerful and maneuverable for all starters as well as FPV pros to practice indoor and outdoor.

Bullet Point

The auxiliary flight function is greatly reducing the threshold of operating. This is the lightest key to open the door to advanced FPV. 
Cetus Pro quadcopter comes with a brushless power system, it's more powerful and maneuverable in flight. Pilots can achieve more FPV freestyle actions to train.
With the self-protection of emergency landing when out of control or in low battery, to ensure a more safe flight. 
Made of PA12 material, the frame has an excellent impact resistance in drop &amp impact. Meanwhile, the 360° protection of the whoop frame ensures safe flights both indoors and outdoors.
All items needed for the flight are packed in an EVA portable storage bag. Better to protect and convenient to carry. 




Altitude Hold, Easy to Fly
The altitude hold function enables Auto-Hover. This quadcopter can stay at a current height when pilots' hands are off the transmitter. Barometer/laser achieves accurate and stable positioning, which makes the quad hovering indoors very stable. The flight has never been so easy for a beginner! 
The altitude hold function is only available in N mode.

Self-protection, No More Dangers
The quadcopter comes with an excellent self-protection function. It can make an emergency landing whenever loses control or is in low battery. It will also automatically disarm and drop on the ground once there is a strong collision with the object. Let's say goodbye to loss and crash!

Turtle Mode, No Burden to Fly Away
When the quadcopter falls to the ground and upside down, we can active turtle mode by LiteRadio2 SE transmitter to flip it over and resume flying. With this function, there is no need to walk away to correct the position manually.
Turtle mode will not work effectively if something gets stuck in the motor/prop. Please push down switch SD on the transmitter immediately in this situation to exit turtle mode. 

3 Flight Modes, From Zero to Hero
Three modes those N/ S/ M are available, which can satisfy the different needs of pilots and adapt to various flight environments. Whether you're a seasoned FPV pilot or a complete beginner, the Cetus Pro FPV Kit helps anyone fly confidently from day one. These 3 flight modes can be switched by one SB switch on transmitter, which is simple and convenient. Meanwhile, all modes support 3 different speeds with SLOW/MID/FAST, pilots can switch it by one SC switch on the transmitter.

Cetus Pro Brushless Quadcopter
Equipped Lite 1-2S Pro brushless flight controller with 12A ESC, matching with 1102 18000KV brushless motors and 40mm 3-blade props, which is absolutely more powerful and maneuverable. Turtle mode greatly makes FPV racing training smooth and convenient.

FPV Simulator Supported
LiteRadio2 SE radio transmitter can be used as a USB Joystick when connected to the computer. So it's available to play FPV simulators like EREADRONE, LIFTOFF. More convenient for practicing and charging at the same time. Besides, the transmitter is more ergonomic with a hobby-grade gimbal and adopted the rubber coat.

New to FPV? No worries. Our new Cetus Pro FPV Kit will take you from zero to hero in no time.This is a very different drone from BETAFPV. It's a brushless whoop drone designed from the ground up for FPV beginners. With three modes, you can start your FPV journey at a stable, basic level – and then progress. If you’ve ever felt that FPV is too difficult to tackle, this is the solution for you.
Click here to know more about LIFTOFF.
Download LIFTOFF.

VR02 FPV Goggles
VR02 FPV Goggles- the First-Person-View Goggles with the simpler operation and powerful function, is specially designed for FPV starters. It comes with built-in 5.8G 14DBI high-quality antennas, you can receive stable and clear images even for long-range flights. Adopt an ergonomic design with a foam sponge faceplate and a three-sided adjustable headband, it fits your face and head perfectly.

Specification

Positioning system: Optical flow/ Barometer/ Laser
Height positioning: Laser/ Barometer
Position locating: Optical flow (effective height 0.3-3m)
Accuracy of auto-hover: Horizontal ±0.2m, vertical ±0.3m (under no wind environment)
Receiver protocol: Frsky D8
Quad: Cetus Pro Brushless Quadcopter

Frame: Cetus Pro Brushless Whoop Frame

Flight controller: Lite 1-2S Pro brushless FC
VTX: 25mW
Camera tilt degree: 30°
Camera: C02 FPV Micro Camera

Transmitter: Literadio2 SE Transmitter

TX mode: Mode 1 &amp Mode 2 optional
Goggles: VR02 Goggles

Motor: 1102-18000KV Brushless motor

Propeller: 40mm 3-blade 1.5mm shaft hole
Takeoff weight: 33.19g (without battery)
Power system: 1S
Battery: BT2.0 450mah 1S Battery (external)
Flight time: 4-5min
Flight distance: 80m (in wide &amp undisturbed environment)

FAQ


Top questions that customers frequently asked about Cetus Pro.

For more info and instructions, please check the User Manual for Cetus Pro FPV Kit 

Recommend the newest BT2.0 550mAh 1S Battery. More flight time and higher discharge rate.

Note: Pilots should remove the battery plate if installing the 550mAh battery on Cetus Pro.
Package

1 * Cetus Pro Brushless Quadcopter  
1 * LiteRadio2 SE Transmitter (Frsky D8 Protocol) 
1 * VR02 FPV Goggles   
2 * BT2.0 450mAh 1S Lipo Battery     
1 * BT2.0 Battery Charger and Voltage Tester
1 * USB Charging Cable (Type-C)
1 * Type-C Adapter
1 * Prop Removal Tool
4 *  40mm 3-blade Props

2 * User Manual
1 * Portable Storage Bag
1 * Phillips Screwdriver

Note: The propellers in the package were modified from three holes to one hole.


Recommended by 5000+ experts and reviews, one of the most popular fpv kits for beginners.Best price and stable quality for fpv drone. The Cetus Pro FPV Kit FPV drone is the best ideal choice for beginners to advance currently. Comes with a Cetus Pro brushless quadcopter, LiteRadio2 SE transmitter, and VR02 FPV Goggles

Cetus Pro FPV Kit

The BETAFPV Cetus Pro FPV Kit is&nbspfinally&nbsphere! It is the best ideal choice for beginners to advance currently. The Cetus Pro FPV Racing Kit comes with the Cetus brushed whoop quadcopter,&nbspLiteRadio2 SE transmitter, and&nbspVR02 FPV Goggles.

The BETAFPV Cetus Pro FPV Kit is finally here! It is the best ideal choice for beginners to advance currently. The Cetus Pro FPV Racing Kit comes with the Cetus brushed whoop quadcopter, LiteRadio2 SE transmitter, and VR02 FPV Gog

BETAFPV Cetus Pro FPV Brushless Whoop Racing Kit

BetaFPV RTF Cetus FPV Kit - Cetus Whoop, Goggles, Transmitter, Batteries, Charger & Case

The highly anticipated Cetus FPV Kit comes! It will be the best choice for FPV beginners to explore the FPV world and bring their family and friends into this hobby. Cetus brushed quadcopter, LiteRadio2 SE transmitter, and VR02 FPV Goggles, everything you need is in a pack!

Bullet Points

Auxiliary flight function is suitable for beginners, greatly reducing the threshold of operating. Now everyone can fly!
Including N-Mode, S-Mode, M-Mode, which can satisfy different needs of pilots and adapt to various flight environments.

Cetus brushed quadcopter, LiteRadio2 SE transmitter, VR02 FPV Goggles, batteries, charger, etc., everything needed for flight is included. 
Equipped with Type-C port charging cable, unified charging port for all parts, more convenient for charging.
All items are stored in an EVA portable storage bag, which provides better protection and is easy to carry.

Altitude Hold Function
The altitude hold function enables the Cetus quadcopter to Auto-Hover. The quadcopter can stay at a current height when pilots' hands are off the transmitter. The barometer/laser achieves accurate and stable positioning, which makes the quad hovering indoors very stable. The flight has never been so easy for a beginner.
The altitude hold function is only available in N mode.
Self-protection Function
The Cetus quadcopter has an excellent self-protection function. Which can make an emergency landing whenever loses control or is in low battery. It will also automatically disarm and drop on the ground once it has a strong collision with the object.  Since then, let's say goodbye to loss and crash!

3 Flight Modes, One Key Switch
Three modes those N/ S/ M are available, which can satisfy the different needs of pilots and adapt to various flight environments. Whether you're a seasoned FPV pilot or a complete beginner, Cetus FPV Kit lets anyone fly confidently from day one. 3 flight modes can be switched by one SB switch on transmitter, simple and convenient. Meanwhile, these 3 modes all support 3 different speeds with SLOW/MID/FAST, pilots can switch it by one SC switch on the transmitter.

Self-developed LiteSilver System
Cetus brushed quadcopter equipped with lite 1S pro FC. which using LiteSilver system and integrated Frsky D8, Rx 25mW VTX, barometer, laser, and optical flow sensor. LiteSilver is a self-developed flight control system based on Silverware and FreeRTOS real-time operating system. It supports customers to adjust parameters as they prefer in the host computers (not yet open to customers).

Literadio2 SE Transmitter
It is designed for FPV racing starters, the LiteRadio 2 SE transmitter comes with a built-in 1000mah 1S battery, having an excellent endurance performance which can up to 8 hours, brings pilots a better flight experience. With the hobby-grade gimbal and adopted the rubber coat, it is more ergonomic.

VR02 FPV Goggles
VR02 FPV Goggles - the First-Person-View Goggles with the simpler operation and powerful function, is specially designed for FPV starters. It comes with built-in 5.8G 14DBI high-quality antennas, you can receive stable and clear images even for long-range flights. Adopt an ergonomic design with a foam sponge faceplate and a three-sided adjustable headband, this FPV Goggles fits your face and head perfectly.

Specification


Positioning system: Optical flow / Barometer / Laser


Height Positioning: Laser / Barometer

Angle Locating: Optical flow ( effective height 0.3-3m)

Accuracy of auto-hover: Horizontal ±0.2m, vertical ±0.3m (under no wind environment)

Receiver protocol: Frsky D8
Flight controller: Lite 1S Pro brushed FC
VTX: 25mW

Camera tilt degree: 25°

Camera: C02 FPV Micro Camera
Transmitter: Literaio2 SE Transmitter

TX mode: Mode 2 (Left stick throttle)

Goggles: VR02 Goggles

Motor: 716-19000KV Brushed motor

Propeller: 31mm 4-blade 0.8mm shaft hole

Takeoff weight: 35g(with battery)
Power system: 1S
Battery: BT2.0 300mah 1S Battery (external)
Flight time: 4-5min
Flight distance: 80m (in wide &amp undisturbed environment)

Cetus Pro Brushless Quadcopter
Cetus Pro Brushless Quadcopter has been released! Pilots who have Cetus FPV Kit or LiteRadio2 SE Transmitter can consider upgrading to the Cetus Pro quad and enjoy a more exclusive FPV racing experience. The Cetus Pro quad has great features like turtle mode and a more powerful brushless system.

FAQ

Top questions that customers frequently asked about Cetus.
For more info and instructions please check the User Manual for the Cetus FPV kit 


Package

1 * Cetus Brushed Quadcopter                             
1 * LiteRadio2 SE Transmitter (Frsky D8 Protocol)                        
1 * VR02 FPV Goggles   
2 * BT2.0 300mAh 1S Lipo Battery     
1 * BT2.0 Battery Charger and Voltage Tester
1 * USB Charging Cable (Type-C)
1 * Type-C Adapter
1 * Prop Removal Tool
4 * 31mm 4-Blade Props
2 * User Manual
1 * Portable Storage Bag
1 * Phillips Screwdriver



Recommended by 5000+ experts and reviews, one of the most popular fpv kits for beginners.Best price and stable quality for fpv drone. These are the RTF Whoop FPV racing kits FPV drone for beginners or training. It will be the best choice for FPV beginners to explore the FPV world

Cetus FPV Kit

BetaFPV's Ready-To-Fly Cetus FPV Kit is the perfect starter kit!
Kit Includes

1 * Cetus Brushed Quadcopter                             
1 * LiteRadio2 SE Transmitter (Frsky D8 Protocol)                        
1 * VR02 FPV Goggles   
2 * BT2.0 300mAh 1S Lipo Battery     
1 * BT2.0 Battery Charger and Voltage Tester
1 * USB Charging Cable (Type-C)
1 * Type-C Adapter
1 * Prop Removal Tool
4 * 31mm 4-Blade Props
2 * User Manual
1 * Portable Storage Bag

Bullet Points

Auxiliary flight function is suitable for beginners, greatly reducing the threshold of operating. Now everyone can fly!
Including N-Mode, S-Mode, M-Mode, which can satisfy different needs of pilots and adapt to various flight environments.

Cetus brushed quadcopter, LiteRadio2 SE transmitter, VR02 FPV Goggles, batteries, charger, etc., everything needed for flight is included. 
Equipped with Type-C port charging cable, unified charging port for all parts, more convenient for charging.
All items are stored in an EVA portable storage bag, which provides better protection and is easy to carry.


Specification


Positioning system: Optical flow / Barometer / Laser


Height Positioning: Laser / Barometer

Angle Locating: Optical flow ( effective height 0.3-3m)

Accuracy of auto-hover: Horizontal ±0.2m, vertical ±0.3m (under no wind environment)

Receiver protocol: Frsky D8
Flight controller: Lite 1S Pro brushed FC
VTX: 25mW

Camera tilt degree: 25°

Camera: C02 FPV Micro Camera
Transmitter: Literaio2 SE Transmitter

TX mode: Mode 2 (Left stick throttle)

Goggles: VR02 Goggles

Motor: 716-19000KV Brushed motor

Propeller: 31mm 4-blade 0.8mm shaft hole

Takeoff weight: 35g(with battery)
Power system: 1S
Battery: BT2.0 300mah 1S Battery (external)
Flight time: 4-5min
Flight distance: 80m (in wide &amp undisturbed environment)

 
Altitude Hold Function
The altitude hold function enables the Cetus quadcopter to Auto-Hover. The quadcopter can stay at a current height when pilots' hands are off the transmitter. The barometer/laser achieves accurate and stable positioning, which makes the quad hovering indoors very stable. The flight has never been so easy for a beginner.
The altitude hold function is only available in N mode.
Self-protection Function
The Cetus quadcopter has an excellent self-protection function. Which can make an emergency landing whenever loses control or is in low battery. It will also automatically disarm and drop on the ground once it has a strong collision with the object. Since then, let's say goodbye to loss and crash!

3 Flight Modes, One Key Switch
Three modes those N/ S/ M are available, which can satisfy the different needs of pilots and adapt to various flight environments. Whether you're a seasoned FPV pilot or a complete beginner, Cetus FPV Kit lets anyone fly confidently from day one. 3 flight modes can be switched by one SB switch on transmitter, simple and convenient. Meanwhile, these 3 modes all support 3 different speeds with SLOW/MID/FAST, pilots can switch it by one SC switch on the transmitter.

Self-developed LiteSilver System
Cetus brushed quadcopter equipped with lite 1S pro FC. which using LiteSilver system and integrated Frsky D8, Rx 25mW VTX, barometer, laser, and optical flow sensor. LiteSilver is a self-developed flight control system based on Silverware and FreeRTOS real-time operating system. It supports customers to adjust parameters as they prefer in the host computers (not yet open to customers).

Literadio2 SE Transmitter
It is designed for FPV racing starters, the LiteRadio 2 SE transmitter comes with a built-in 1000mah 1S battery, having an excellent endurance performance which can up to 8 hours, brings pilots a better flight experience. With the hobby-grade gimbal and adopted the rubber coat, it is more ergonomic.

VR02 FPV Goggles
VR02 FPV Goggles- the First-Person-View Goggles with the simpler operation and powerful function, is specially designed for FPV starters. It comes with built-in 5.8G 14DBI high-quality antennas, you can receive stable and clear images even for long-range flights. Adopt an ergonomic design with a foam sponge faceplate and a three-sided adjustable headband, this FPV Goggles fits your face and head perfectly.

Cetus Pro Brushless Quadcopter
Cetus Pro Brushless Quadcopter has been released! Pilots who have Cetus FPV Kit or LiteRadio2 SE Transmitter can consider upgrading to the Cetus Pro quad and enjoy a more exclusive FPV racing experience. The Cetus Pro quad has great features like turtle mode and a more powerful brushless system.

FAQ
1. What is the maximum Flight distance of the Cetus FPV kit?
With 25mW VTX, the quadcopter can fly 80m in a wide &amp undisturbed environment.2. Do you recommend flying this RTF kit indoors or outdoors?
We highly recommend pilot fly this kit indoors. For more info and instructions please check the User Manual for the Cetus FPV kit 


BetaFPV's Ready-To-Fly Cetus FPV Kit is the perfect starter kit! Kit Includes 1 * Cetus Brushed Quadcopter 1 * LiteRadio2 SE Transmitter (Frsky D8 Protocol) 1 * VR02 FPV Goggles 2 * BT2.0 300mAh 1S Lipo Battery 1 * BT2.0 Battery Charger and Voltage Tester 1 * USB Charging Cable (Type-C) 1 * Type-C Adapter 1 * Prop Removal Tool 4 * 31mm 4-Blade Props 2 * User Manual 1 * Portable Storage Bag Bullet Points Auxiliary flight function is suitable for beginners, greatly reducing the threshold of operating. Now everyone can fly! Including N-Mode, S-Mode, M-Mode, which can satisfy different needs of pilots and adapt to various flight environments. Cetus brushed quadcopter, LiteRadio2 SE transmitter, VR02 FPV Goggles, batteries, charger, etc., everything needed for flight is included. Equipped with Type-C port charging cable, unified charging port for all parts, more convenient for charging. All items are stored in an EVA portable storage bag, which provides better protection and is easy to carry. Specification Positioning system: Optical flow / Barometer / Laser Height Positioning: Laser / Barometer Angle Locating: Optical flow ( effective height 0.3-3m) Accuracy of auto-hover: Horizontal ±0.2m, vertical ±0.3m (under no wind environment) Receiver protocol: Frsky D8 Flight controller: Lite 1S Pro brushed FC VTX: 25mW Camera tilt degree: 25° Camera: C02 FPV Micro Camera Transmitter: Literaio2 SE Transmitter TX mode: Mode 2 (Left stick throttle) Goggles: VR02 Goggles Motor: 716-19000KV Brushed motor Propeller: 31mm 4-blade 0.8mm shaft hole Takeoff weight: 35g(with battery) Power system: 1S Battery: BT2.0 300mah 1S Battery (external) Flight time: 4-5min Flight distance: 80m (in wide & undisturbed environment) Altitude Hold Function The altitude hold function enables the Cetus quadcopter to Auto-Hover. The quadcopter can stay at a current height when pilots' hands are off the transmitter. The barometer/laser achieves accurate and stable positioning, which makes the quad hovering indoors very stable. The flight has never been so easy for a beginner. The altitude hold function is only available in N mode. Self-protection Function The Cetus quadcopter has an excellent self-protection function. Which can make an emergency landing whenever loses control or is in low battery. It will also automatically disarm and drop on the ground once it has a strong collision with the object. Since then, let's say goodbye to loss and crash! 3 Flight Modes, One Key Switch Three modes those N/ S/ M are available, which can satisfy the different needs of pilots and adapt to various flight environments. Whether you're a seasoned FPV pilot or a complete beginner, Cetus FPV Kit lets anyone fly confidently from day one. 3 flight modes can be switched by one SB switch on transmitter, simple and convenient. Meanwhile, these 3 modes all support 3 different speeds with SLOW/MID/FAST, pilots can switch it by one SC switch on the transmitter. cetus fpv kit N/S/M mode Self-developed LiteSilver System Cetus brushed quadcopter equipped with lite 1S pro FC. which using LiteSilver system and integrated Frsky D8, Rx 25mW VTX, barometer, laser, and optical flow sensor. LiteSilver is a self-developed flight control system based on Silverware and FreeRTOS real-time operating system. It supports customers to adjust parameters as they prefer in the host computers (not yet open to customers). cetus fpv kit for beginners Literadio2 SE Transmitter It is designed for FPV racing starters, the LiteRadio 2 SE transmitter comes with a built-in 1000mah 1S battery, having an excellent endurance performance which can up to 8 hours, brings pilots a better flight experience. With the hobby-grade gimbal and adopted the rubber coat, it is more ergonomic. literadio2 transmitter VR02 FPV Goggles VR02 FPV Goggles- the First-Person-View Goggles with the simpler operation and powerful function, is specially designed for FPV starters. It comes with built-in 5.8G 14DBI high-quality antennas, you can receive stable and clear images even for long-range flights. Adopt an ergonomic design with a foam sponge faceplate and a three-sided adjustable headband, this FPV Goggles fits your face and head perfectly. VR02 goggle Cetus Pro Brushless Quadcopter Cetus Pro Brushless Quadcopter has been released! Pilots who have Cetus FPV Kit or LiteRadio2 SE Transmitter can consider upgrading to the Cetus Pro quad and enjoy a more exclusive FPV racing experience. The Cetus Pro quad has great features like turtle mode and a more powerful brushless system. Cetus family FAQ 1. What is the maximum Flight distance of the Cetus FPV kit? With 25mW VTX, the quadcopter can fly 80m in a wide & undisturbed environment. 2. Do you recommend flying this RTF kit indoors or outdoors? We highly recommend pilot fly this kit indoors. For more info and instructions please check the User Manual for the Cetus FPV kit

Cetus FPV Flight Kit

BetaFPV's Ready-To-Fly Cetus FPV Kit is the perfect starter kit! Kit Includes 1 * Cetus Brushed Quadcopter                              1 * LiteRadio2 SE Transmitter (Frsky D8 Protocol)                         1 * VR02 FPV Goggles    2 * BT2.0 300mAh 1S Lipo Battery      1 * BT2.0 Battery Charger and Voltage Tester 1 * USB Charging Cable (Type-C) 1 * Type-C Adapter 1 * Prop Removal Tool 4 * 31mm 4-Blade Props 2 * User Manual 1 * Portable Storage Bag Bullet Points Auxiliary flight function is suitable for beginners, greatly reducing the threshold of operating. Now everyone can fly! Including N-Mode, S-Mode, M-Mode, which can satisfy different needs of pilots and adapt to various flight environments. Cetus brushed quadcopter, LiteRadio2 SE transmitter, VR02 FPV Goggles, batteries, charger, etc., everything needed for flight is included.  Equipped with Type-C port charging cable, unified charging port for all parts, more convenient for charging. All items are stored in an EVA portable storage bag, which provides better protection and is easy to

The highly anticipated Cetus FPV Kit comes! It will be the best choice for FPV beginners to explore the FPV world and bring your family and friends into this hobby. With Cetus brushed quadcopter, LiteRadio2 SE transmitter, and VR02 FPV Goggles, everything you need is in a pack! Check out all our Analog BNF/PNP/RTF Kits

BetaFPV Cetus FPV RTF Kit W/Goggles & Controller

The BETAFPV Cetus FPV Kit has everything you need to begin your flying experience!&nbspThe highly anticipated Cetus FPV Kit is the best choice for FPV beginners to explore the FPV world and bring your family and friends into this hobby. The Cetus FPV Racing comes with the Cetus brushed whoop quadcopter,&nbspLiteRadio2 SE transmitter, and&nbspVR02 FPV Goggles, which is everything you need to get up in the air!

The BETAFPV Cetus FPV Kit has everything you need to begin your flying experience! The highly anticipated Cetus FPV Kit is the best choice for FPV beginners to explore the FPV world and bring your family and friends into this hobby. The Cetus FP

BETAFPV RTF Cetus Beginner FPV Kit - Brushed Version

iFlight BNF Alpha A75 Analog Whoop

You've seen the A65 and the A85. Well, it would make sense for iFlight to release the A75 to fill the gap in size!

iFlight Alpha A75 Whoop - Analog w/ RaceCam R1

T-Motor

T-Motor BNF TRON 80 HD 1.6" Cinewhoop

TRON 80 Whoop HD comes with a pusher frame design for stability, efficiency, and easy control. Also 4 RGB LED lights bring cool visual effects to your flying experience! This HD whoop also comes with the Caddx Nebula Nano and Vista VTX, F1103 8000KV motors, 13A AIO, and 40mm 4-blade props. You can also mount a Naked Go

T-Motor Tron 80 Whoop w/ HD Digital VTX

Tiger Motors

The TRON 80 Whoop HD is an FPV racing drone by T-Motor that is equipped with 4 RGB LED lights to bring cool visual effects to your flying experience!&nbspExcellent for indoor racing, small cinematic rigs, freestyle, and endless opportunities!

The TRON 80 Whoop HD is an FPV racing drone by T-Motor that is equipped with 4 RGB LED lights to bring cool visual effects to your flying experience! Excellent for indoor racing, small cinematic rigs, freestyle, and endless opportunities!

T-Motor TRON 80 3S HD CineWhoop 1.6" FPV Racing Drone

T-Motor TRON 80 3S HD CineWhoop 1.6&quot FPV Racing Drone

GEPRC

GEPRC RTF TinyGO 4K FPV Whoop Kit

Large Volume and Including 4 PCS 1S Batteries. Please don't select Standard Shipping way.

GEPRC TinyGO 4K FPV Whoop RTF - GEPRC

GEPRC TinyGO 4K FPV Whoop RTF

GEPRC is happy with their new release of the TinyGO, which comes in a ready-to-fly whoop kit! GEPRC has worked so hard to create a lightweight whoop that is suitable for indoor flying, has max performance, and with their 4K version, one can record video up to 4K 60fps.

GEPRC is happy with their new release of the TinyGO, which comes in a ready-to-fly whoop kit! GEPRC has worked so hard to create a lightweight whoop that is suitable for indoor flying, has max performance, and with their 4K version, one can record vi

GEPRC TinyGO 4K FPV Whoop RTF Kit (Mode 2)

GEPRC RTF TinyGO Racing FPV Whoop Kit

GEPRC is happy with their new release of the TinyGO, which comes in a ready-to-fly whoop kit! GEPRC has worked so hard to create a lightweight whoop that is suitable for indoor flying, has max performance, and is a great racing whoop drone!

GEPRC TinyGO Racing FPV Whoop RTF Kit (Mode 2)

GEPRC TinyGO Racing FPV Whoop RTF - GEPRC

GEPRC TinyGO Racing FPV Whoop RTF

GEPRC RTF TinyGO LED FPV Whoop Kit

Pre-Orders shipping ASAP! All products containing batteries must be shipped by a ground shipping method.
The GEPRC TinyGo LED version is a full-color RGB series whoop, specially designed and modified to celebrate the coming festival. Compare with the TinyGo Racing Version,  the TinyGo LED version replaces the EVO anti-collision sponge with LED straps. The total weight without batteries is under 55 grams. It lasts for 4-5 minutes in LED mode and 5-6 minutes in normal mode. There are 52 high-brightness small LED lamps in the whole Quadcopter. The LEDs can be programmed through Betaflight. You can customize the colors and styles as you wish. When flying at night, you can enjoy the pleasure of a colorful flight. It should be noted that the LED lamp won’t be waterproof, so please avoid flying in a wet environment. 
The TinyGO LED is an RTF Kit for Indoor Flights. The Kit contains high-definition 800x480px FPV Goggles and the latest TinyRadio GR8 Remote Controller. It supports 8 channels and is designed for indoor flights and novices. The transmitter has a good feeling of control and It is lightweight and easy to carry. The good point is that you don’t need to carry heavy equipment. With our customized GEPRC Fly Bag. it’s very convenient to go to the field, travel, and on Indoor flights.
The TinyGO LED can use its own charger to charge. The charger uses the Type-C interface. You can use the movable power bank to charge as well. 
The TinyGO LED can be flown for more than 4 minutes (Depending on flight habits). Its stable electronic equipment and extremely strong and tough frame material make the FPV very stable and durable for crashes. There is an EVA protection foam around the frame,  more elastic and hard to damage.
TinyGO LED is carefully assembled by the GEPRC team, with excellent performance. You can start a whole new journey and enter into FPV World. TinyGO will be the best choice for your first FPV Drone.
This looks like the beginning of a terrific flight Experience. Literally!
Check out our other RTF combos, all our pre-built quads, and our GEPRC selection!
Note: If you buy a drone only, If you have a new TinyRadio GR8 remote controller, it can be directly bound, and the old version of the GEPRC GR8 remote controller should be bound by flashing the old version of the CLI
Changelog

January 12, 2022: TinyGo shipped today will have the new remote controller and the new charger version.
December 16, 2022: VTX changed from 5.8G 25~200mW VTX to RAD Whoop 5.8G 400mw VTX
December 16, 2022: The flight controller changed from GEP-12A-F4 to TAKER F411 8Bit 12A FC


Features

TinyGO LED is very suitable for indoor flights. More than 4 minutes of flight time
Using GEPRC-12A-F4 FC system is reliable and stable
No Propellers in view. Anti-jamming VTX. NO Jello flight Footage. Stable flight picture quality
The Newly Developed TinyRadio GR8 Remote Controller is specially designed for Novice and indoor flights
It has High-Quality FPV Goggles, with High definition 800x480px., and a sensitive 5.8G receiver
Ready To Fly Kit, Includes a GEPRC Fashion Fly bag. Portable and Lightweight.

Specifications

Name: TinyGO
Brand: GEPRC
Frame: GEP-TG16
Motor to Motor: 79mm
FC: TAKER F411 8Bit 12A
MCU: STM32F411
IMU: 42688-P
Blackbox: 16Mb
OSD: BetaFlight OSD w/ AT7456E chip
ESC: 8Bit 12A
VTX: RAD Whoop 5.8G 400mw VTX
Camera: Runcam Nano2/Caddx Loris 4K 60fps
Propeller: GEMFAN 1636x4 (4 pairs)
Motors: GR1102 10000Kv
TinyGO LED Weight (Without Batteries): 55 Grams

Remote Controller

TinyRadio GR8 Remote Controller
Radio Frequency: 2.4GHz
Radio Protocol: FHSS
Channel:8
Transmit Power: &amplt20 dBm
Antenna interface: SMA
Low Voltage alarm: &amplt6.6v
Batteries: two 18650 batteries or a 2S battery. (not included)

Receiver

Channel: 8
Voltage: 5V
Radio Frequency: 2.4GHz
Radio Protocol: FHSS
Range: 100 meter

FPV Goggle

Resolution: 800x480px
Size of Screen: 4.3 inch
Whole Size: 155x144x113mm
In-built batteries: 3.7v/2000mAh
Working Hours: 2.5 Hours
Weight: 314.6 Grams

FPV Batteries

Batteries Capacity: 530mAh
Voltage: 4.35v 1S1P
Discharge rate: 90C
Size: 61x16.7x7mm
Weight: 12.7 Grams
Interface: PH2.0

Charger

Input power: 5v (USB Type C）
Full charged Voltage: 4.35v
Output current: 1Ah
Charging: It can charge 2 PCS 1s HV lipo 4.35v HP2.0/GNB27 plug batteries at the same time

Includes

1x TinyGO LED Quadcopter
1x TinyRadio GR8 Transmitter
1x GEPRC FPV RG1 Goggle
1x GEPRC 1S LiHV 4.35v Charger
4x GEPRC LiHV 4.35v 90C Batteries
1x Battery strap



Pre-Orders shipping ASAP! All products containing batteries must be shipped by a ground shipping method. The GEPRC TinyGo LED version is a full-color RGB series whoop, specially designed and modified to celebrate the coming festival. Compare with the TinyGo Racing Version,  the TinyGo LED version replaces the EVO anti-

GEPRC RTF TinyGo LED FPV Ready To Fly Analog Kit w/ Goggles, Radio Transmitter, Case & Drone from WREKD Co.

(PRE-ORDER) GEPRC RTF TinyGo LED FPV Ready To Fly Analog Kit w/ Goggles, Radio Transmitter, Case & Drone

GEPRC is happy with their new release of the TinyGO, which comes in a ready-to-fly whoop kit! GEPRC has worked so hard to create a lightweight whoop that is suitable for indoor flying, has max performance, and with their LED version, pilots can have the pleasure of flying at night.

GEPRC is happy with their new release of the TinyGO, which comes in a ready-to-fly whoop kit! GEPRC has worked so hard to create a lightweight whoop that is suitable for indoor flying, has max performance, and with their LED version, pilots can have 

GEPRC TinyGO LED FPV Whoop RTF Kit (Mode 2)

Large Volume and Including 4 PCS 1S Batteries.Please don't select Standard Shipping way.

GEPRC TinyGO LED FPV Whoop RTF - GEPRC

GEPRC TinyGO LED FPV Whoop RTF

EMAX BNF Nanohawk Micro Quadcopter

In an effort to push the boundaries of miniaturizing the FPV experience, EMAX took to the drawing board to design the smallest quadcopter possible in their history. Introducing the NanoHawk, a nano sized FPV drone designed to offer an immersive flight experience in a new scale.Weighing in at just 20 grams, the NanoHawk

Emax Nanohawk 1S Ultralight Brushless FPV Drone

Introducing the Nanohawk, a nano-sized FPV drone designed to offer an immersive flight experience on a new scale.

EMAX Nanohawk 1S Micro Brushless FPV Drone (FrSky - BNF)

EMAX RTF TinyHawk II  Ready to Fly Kit - Googles, Radio Transmitter, Case and 75mm Indoor Racing Whoop Drone

Great beginner RTF kit by EMAX! Comes with everything you need to rip! See our Tinyhawk II collection! Check out all our BNF-PNP-RTF quads and Emax collection!Recommended Batteries : 1S: GNB 1S 450MAH HIGH VOLTAGE 80C PH 2.0 GNB 1S 450MAH 80C PH 2.0. AULINE 450MAH HV 3.8V 1S LIPO 80C PH2.0 - 4PCS 2S: GNB 300MAH 2S 7.6V

EMAX TINYHAWK II RACING DRONE RTF WITH RUNCAM NANO2 RTF

The RTF Bundle gives you everything you need to start flying in just minutes. Everything is included, goggles, radio, and of course the TinyHawk II quadcopter! This bundle is the perfect solution for anyone to learn the basic of FPV flying, beginners and pros alike.

The RTF Bundle gives you everything you need to start flying in just minutes. Everything is included, goggles, radio, and of course the TinyHawk II quadcopter! This bundle is the perfect solution for anyone to learn the basic of FPV flying, beginners

EMAX TinyHawk II Micro Brushless FPV Drone (RTF Bundle)

Tinyhawk II 2 Indoor FPV Racing Drone F4 5A 16000KV RunCam Nano2 700TVL 37CH 25/100/200mW VTX 1S-2S - RTF

Tinyhawk II RTF Kit - With Controller & Goggles

Our TinyHawk II Freestyle RTF Bundle is the best way to get into FPV! The quality products in this bundle have been handpicked and pre-bound together by our team to give you the best micro experience.

EMAX TinyHawk II Freestyle 2S Micro FPV RTF Bundle w/ BETAFPV LiteRadio 2 + EMAX Transporter Goggles

BetaFPV BNF Beta65S Lite Micro Whoop Quadcopter

Beta65S with 7x16mm brushed motors have upgraded F4 Brushed FC with M01 AIO Camera 5.8G VTX. The table below shows the FC and RX that come with the drone according to the version you choose. Please note the SPI Frsky RX is the FCC version.
Note: There are some changes to the Beta65S BNF Micro Whoop Quadcopter. First, the new F4 1S AIO flight controller uses MPU6500 gyro instead of MPU6000 gyro. BT2.0 battery and cable take the place of PH2.0. Finally, the Frsky protocol version is modified from Frsky FCC to Frsky D8.




Frsky Version
DSMX Version
Flysky Version
Futaba Version
No RX Version


FC
F4 Brushed FC
F4 Brushed FC
F3 Flysky FC
F4 Brushed FC
F4 No RX FC


RX
SPI Frsky RX
Native DSMX RX
SPI Flysky RX
SPI FUTABA RX
None



 

Note: If you are a Spektrum DXe radio transmitter or OrangeRX RF module user and find that you can't bind successfully, please create a ticket to contact us.
Bullet Point

The latest Beta65S has been updated with the newest canopy which is more durable. 
More punch on the throttle with faster 19000KV 7x16mm motors and 3-blade propellers.
A great alternative to the popular regular whoop drone.
Provide 3 receiver versions for choice, including SPI Frsky Rx, DSMX Rx, SPI FUTABA Rx, and Flysky Rx.
BETAFPV M01 AIO VTX camera with 48 channels in total.

Comparison
Here is the size comparison between Beta65/65S, Beta75/75S, and Beta85 drones. 


Specification

Frame: 65s frame V4

Weight: 25g (without battery)
Flight Controller: BETAFPV F4 Brushed FC / F4 Brushed NO RX FC /  F3 Flysky FC / F4 Brushed FC (DSMX RX)

Motor: 7x16mm Coreless Brush Motor, 19000KV

Receiver: SPI Frsky D16 protocol / SPI FUTABA RX / SPI Flysky RX /  Native DSMX RX

Cam: M01 AIO Camera 5.8G VTX

Canopy: Canopy for micro camera / Canopy for Micro Camera 2022

Power connector: JST-PH 2.0 connector, AKA PowerWhoop connector (old version) / BT2.0 connector, BT2.0-PH2.0 Adapter Cable, BT2.0 1S Whoop Cable Pigtail (new version)

Battery: 300mAh 1S Lipo Battery (old version) / BT2.0 300mAh 1S 30C Battery (new version)

Propeller: HQ 31mm 3-Blade Propellers (0.8mm Shaft 4PCS)

Flight time: 3 min 30 second


Package

1 * Beta65S Micro FPV Quad
2 * 300mAh 1S Lipo Battery

1 * Carry-on bag 
1 * Screwdriver
3 * Decorative Parts


Beta65S with 7x16mm brushed motors have upgraded F4 Brushed FC with M01 AIO Camera 5.8G VTX. The table below shows the FC and RX that come with the drone according to the version you choose. Please note the SPI Frsky RX is the FCC version. Note: There are some changes to the Beta65S BNF Micro Whoop Quadcopter. First, t

Beta65S BNF Micro Whoop Quadcopter

The BETAFPV Beta65S Lite is a new version of whoops that comes with the BETAFPV Lite Brushed Flight Controller. 

BETAFPV Beta65S Lite Micro Whoop Quadcopter - BNF

GEPRC BNF Thinking P16 Cinewhoop

The GEPRC Thinking P16 comes with the&nbspCaddx Loris 4k FPV Camera System. The&nbsp4K version of the Thinking P16 comes with the GEP-12A-F4 AIO, which is a highly integrated and stable board that weighs only 5.6g.

The GEPRC Thinking P16 comes with the Caddx Loris 4k FPV Camera System. The 4K version of the Thinking P16 comes with the GEP-12A-F4 AIO, which is a highly integrated and stable board that weighs only 5.6g.

GEPRC Thinking P16 3S CineWhoop w/ Caddx Loris 4K Camera System

Thinking P16 4K comes with the GEP-12A-F4 AIO which is a highly integrated and stable board that weighs only 5.6g.GEP-12A-F4 AIO gives you confidence while you are trying to push your Thinking P16 4K to its limit. GR1103 8000kv motors and 1.6’’ props combined with a 3S 300mah Lipo battery gives Thinking P16 4K a stable

GEPRC BNF Thinking P16 4K 79mm Cinewhoop w/ Caddx Loris 4K Camera - Choose RX Type

EMAX BNF Tinyhawk II Racing Quadcopter

Emax took the already amazing Tinyhawk and made it the perfect micro indoor and outdoor racing drone by adding industry standard Runcam Nano 2 camera on an adjustable mount and higher output VTX up to 200mW with more filtering.Find parts and accessories in our TinyHawk 2 Collection! Frame: Wheelbase: 75mm Dry Weight: 3

EMAX Tinyhawk 2 racing Drone BNF With Runcam Nano2

Besides being a beginner-friendly, fun and micro-sized drone, EMAX's Tinyhawk II Race is a more performance-oriented outdoor 2S quadcopter. 

EMAX Tinyhawk II Race Micro Brushless FPV Drone w/ RunCam Nano 2 

Tinyhawk II Race FPV Racing Drone F4 5A 7500KV RunCam Nano2 700TVL 37CH 25/100/200mW VTX 2S - BNF

Tinyhawk II Race BNF

EMAX has gone back to make what was already an amazing micro quadcopter even better, with a RunCam Nano 2 FPV Camera with adjustable tilt, higher power VTX, LEDs, and more powerful motors.

EMAX TinyHawk 2 Micro Brushless FPV Drone w/ RunCam Nano 2 (BNF)









 
 Frame
Wheelbase: 90mm
Dry Weight: 47.5g
All Up Weight: 73g with 2x 450mAh 1S battery
Frame Material: Polypropylene &ampamp Carbon Fiber
 

 Motors
Stator Size: 1103
Kv: 7500kv
Propeller Mount: T-mount
Propeller: Avan Blur 2&quot/span&ampgt
 

 All-In-One (AIO) Flight Controller
Flight Controller: F4 (MATEKF411RX Firmware)
ESC: 4-in-1 5A BlHeli_S
Receiver: EMAX SPI Receiver (Compatible with FrSky D8 mode**)
Battery Connector: JST-PH2.0 Duo
 

 FPV System
Ham radio license required for use in North America.
VTX Power: 25/100/200mw Switchable (set to stay at 25mW until armed)*
Channels: 37CH incl. Raceband
Camera: RunCam Nano 2 1/3&quot 700TVL CMOS
Smart Audio Connected
 

 Includes
1x Tinyhawk II Race BNF
2x EMAX 450mAh 1S HV Battery
1x 1S USB LiPo Charger
1x Screwdriver + Hardware Kit
 
*Please note that even if you unlocked the video transmitter (VTX) per the manual and are changing power levels via the OSD/Smart Audio (VTX SA), the Race is set to stay at 25mW until you arm the motors.
** Be advised that this model is NOT compatible with the latest 2019+ FrSky ACCESS protocol transmitters without the use of FrSky&#39s external XJT module for ACCESS transmitters for D8 mode capability.
 
RECOMMENDED FOR CHILDREN 14+ YEARS OF AGE

   Frame Wheelbase: 90mm Dry Weight: 47.5g All Up Weight: 73g with 2x 450mAh 1S battery Frame Material: Polypropylene &amp; Carbon Fiber    Motors Stator Size: 1103 Kv: 7500kv Propeller Mount: T-mount Propeller: Avan Blur 2"/span&gt;    All-In-One (AIO) Flight Controller Flight Controller: F4 (MATEKF411RX Firmware) ESC