FPV Quad Parts

Peripherals and Replacement Parts

Equipment

Equipment Peripherals

Build Page Parts

Build Parts Equipment

Pre-Built Quads and Kits 

Build Page Parts Overflow

Build Parts Equipment Overflow

Compatibility Categories

DJI Avata 2

Experience an immersive flight with the DJI Avata 2 FPV Drone, featuring intuitive motion control, super-wide 4K capture, and easy POV content creation. Enjoy adrenaline-pumping FPV flight with improved imaging, safety, and extended battery life. Execute effortless aerial acrobatics like flips and drifts, ideal for cap

(PRE-ORDER) DJI Avata 2 FPV Drone

Experience an immersive flight with the DJI Avata 2 FPV Drone, featuring intuitive motion control, super-wide 4K capture, and easy POV content creation.&nbsp

Experience an immersive flight with the DJI Avata 2 FPV Drone, featuring intuitive motion control, super-wide 4K capture, and easy POV content creation. 

Avata 2 features more flight time, more range, a more internal store, an improved camera and much more! Check out our in-depth review below!
Features

Immersive Flight Experience
Intuitive Motion Control (when used with RC Motion 3 Controller)
Tight Shots in Super-Wide 4K
Easy ACRO
Built-in Propeller Guard
Hassle-Free POV Content
Easy ACRO
Flip, Roll, 180° Drift
1/1.3″ CMOS Super-Wide-Angle Camera
4K/60fps HDR Videos 
10-bit D-Log M Color Mode
Downward/Backward Visual Positioning
23-Min Max Flight Time
The drone supports PD fast charging.
DJI O4 Video Transmission
Max Transmission Distance: 13 km
Max Transmission Bitrate: 60Mbps
46GB Large Internal Storage
High-Speed QuickTransfer


Specifications
DJI Avata 2 Drone

Takeoff Weight: Approx. 377 g
Dimensions: 185×212×64 mm (L×W×H)
Max Ascent Speed: ‌6 m/s (Normal mode), 9 m/s (Sport mode)
Max Descent Speed:
Max Horizontal Speed: (near sea level, no wind) 8 m/s (Normal mode), ‌16 m/s (Sport mode), 27 m/s (Manual mode)*
Max Flight Time: ‌Approx. 23 mins
Max Hovering Time: ‌Approx. 21 mins
Max Flight Distance: 13.0 km‌
Max Wind Speed Resistance: 10.7 m/s (Level 5)
Operating Temperature: -10° to 40° C (14° to 104° F)
Global Navigation Satellite System: GPS + Galileo + BeiDou
Hovering accuracy range: Vertical: ±0.1 m (with vision positioning), ±0.5 m (with GNSS positioning)Horizontal: ±0.3 m (with vision positioning), ±1.5 m (with GNSS positioning)
Internal Storage: 46 GB
Image Sensor: ‌1/1.3-inch image sensor
Effective Pixels: 12 MPLens ‌FOV: 155°Format Equivalent: 12 mm
Aperture: f/2.8
Focus: 0.6 m to ∞
ISO Range: 100-25600 (Auto), 100-25600 (Manual)
Shutter Speed Video: 1/8000-1/30 s
Photo: 1/8000-1/50 s
Max Image Size: 4000×2256 (16∶9), 4000×3000 (4∶3)
Still Photography Mode: Single shot
Photo Format: JPEG
Video Resolution 4K (4∶3): 3840×2880@30/50/60fps4K (16∶9): 3840×2160@30/50/60fps2.7K (4∶3): 2688×2016@30/50/60fps2.7K (16∶9): 2688×1512@30/50/120fps1080p (4∶3): 1440×1080@30/50/120fps1080p (16∶9): 1920×1080@30/50/120fps
Video Format: MP4 (H.264/H.265)Max Video Bitrate: 130 Mbps
Supported File System: exFAT
Color Mode: Standard, D-Log M
Camera FOV: Supports normal mode, wide-angle mode, and ultra-wide-angle mode.
EIS: Supports RockSteady 3.0+ and HorizonSteady, Can be disabled*
Stabilization: Single-axis mechanical gimbal (tilt)
Mechanical Range Tilt: -95° to 90°
Controllable Range Tilt: -85° to 80°
Max Control Speed (tilt): 100°/s
Angular Vibration Range: ±0.01°
Sensing Type: Downward and backward visual positioningDownward ToF Effective Measurement Height: 10 mPrecise Hovering Range: 0.3-10 mMeasurement Range: 0.3-20 mFOV: Horizontal 78°, Vertical 78°Backward Measurement Range: 0.5-20 mFOV: Horizontal 78°, Vertical 78°Adequate lighting: (lux &gt 15, normal indoor lighting conditions)
Video Transmission System: O4
Live View Quality: 1080p@30/50/60/100fps
Operating Frequency: 2.400-2.4835 GHz,5.170-5.250 GHz*,5.725-5.850 GHz*
Transmitter Power (EIRP):2.4 GHz: ＜33 dBm (FCC), ＜20 dBm (CE/SRRC/MIC)5.1 GHz: &lt 23 dBm (CE)5.8 GHz: ＜33 dBm (FCC),＜30 dBm (SRRC), &lt 14 dBm (CE)
Communication Bandwidth: Max 60 MHz
Max Transmission Distance: (unobstructed, free of interference) FCC: 13 km (subject to the aircraft's max flight distance), CE: 10 km, SRRC: 10 km, MIC: 10 km
Max Transmission Distance (unobstructed, with interference)Strong Interference: Urban landscape, approx. 1.5-4 kmMedium Interference: Suburban landscape, approx. 4-10 kmLow Interference: Suburb/seaside, approx. 10-13 kmMax Transmission Distance (obstructed, with interference) Low Interference and Obstructed by Buildings: approx. 0-0.5 kmLow Interference and Obstructed by Trees: approx. 0.5-3 km
Max Download Speed Wi-Fi: 30 MB/s*
Lowest Latency With DJI Goggles 3:1080p/100fps Video Transmission Quality: 24 ms1080p/60fps Video Transmission Quality: 40 ms‌
Max Video Bitrate: 60Mbps
Antennas: 4 antennas, 2T4R
Protocol: 802.11a/b/g/n/ac
Operating Frequency: 2.400-2.4835 GHz, 5.725-5.850 GHzTransmitter Power: (EIRP) 2.4 GHz: &lt20 dBm (FCC／CE／SRRC／MIC)5.8 GHz: &lt20 dBm (FCC／SRRC), &lt 14 dBm (CE)Protoco:l Bluetooth 5.0Operating Frequency 2.400-2.4835 GHzTransmitter Power (EIRP) &lt10 dBm

Battery

Capacity: 2150 mAh
Weight: Approx. 145 g
Standard Voltage: 14.76 V
Max Charging Voltage 17 V
Battery Type: Li-ion
Energy: 31.7 Wh@0.5C
Charging Temperature: 5° to 40° C (41° to 104° F)
Charging Time With Charging Hub: (60W max charging power):From 0 to 100%: approx. 45 min‌From 10 to 90%: approx. 30 min‌‌
Directly Charging the Drone (30 W max charging power):‌From 0 to 100%: approx. 88 min‌From 10 to 90%: approx. 60 min‌‌‌‌

Includes

1x DJI Avata 2 Drone
1x DJI Avata 2 Intelligent Flight Battery
2x DJI Avata 2 Propellers (Pair)
8x DJI Avata 2 Propeller Screw
1x DJI Avata 2 Gimbal Protector
1x Type-C to Type-C PD Cable
1x Screwdriver


Avata 2 features more flight time, more range, a more internal store, an improved camera and much more! Check out our in-depth review below! Features Immersive Flight Experience Intuitive Motion Control (when used with RC Motion 3 Controller) Tight Shots in Super-Wide 4K Easy ACRO Built-in Propeller Guard Hassle-Free P

(PRE-ORDER) DJI Avata 2 Drone

Avata 2 features more flight time, more range, a more internal store, an improved camera and much more! Check out our in-depth review below! Features Immersive Flight Experience Intuitive Motion Control (when used with RC Motion 3 Controller) Tight Shots in Super-Wide 4K Easy ACRO Built-in Propeller Guard Hassle-Free POV Content Easy ACRO Flip, Roll, 180° Drift 1/1.3″ CMOS Super-Wide-Angle Camera 4K/60fps HDR Videos 10-bit D-Log M Color Mode Downward/Backward Visual Positioning 23-Min Max Flight Time The drone supports PD fast charging. DJI O4 Video Transmission Max Transmission Distance: 13 km Max Transmission Bitrate: 60Mbps 46GB Large Internal Storage High-Speed QuickTransfer Specifications DJI Avata 2 Drone Takeoff Weight: Approx. 377 g Dimensions: 185×212×64 mm (L×W×H) Max Ascent Speed: ‌6 m/s (Normal mode), 9 m/s (Sport mode) Max Descent Speed: Max Horizontal Speed: (near sea level, no wind) 8 m/s (Normal

Pre-Orders shipping ASAP! All products with batteries must be shipped by a ground shipping method.
All Thrills and No Frills. Experience the Avata 2 and enjoy immersive flight.
Check out our other RTF combos, all our pre-built quads and all of our DJI products!
Features





All Thrills, No Frills

Immersive Flight Experience
Intuitive Motion Control
Tight Shots in Super-Wide 4K
Easy ACRO
Built-in Propeller Guard
Hassle-Free POV Content

Fully Experience Flight DJI Avata 2 delivers an adrenaline-pumping immersive FPV drone experience with improved imaging, safety, and battery life. Amp up the fun when you pair Avata 2 with the new DJI Goggles 3 and DJI RC Motion 3.
Tight Shots in Super-Wide 4K Create breathtaking visuals with Avata 2's 155° FOV and its ability to swiftly approach and pull away from subjects. New pilots can quickly master aerobatic shots and capture fast-moving dynamic low-altitude shots that other drones can't.

155° Ultra-Wide-Angle FOV of Avata 2
82° Standard View of Camera Drones

1/1.3-inch Image SensorThe upgraded 1/1.3-inch image sensor expands the captured dynamic range, handling low-light conditions more effectively to capture outstanding footage on every flight.

Effective Pixels: 12 MP
Offline Stabilization: Gyroflow

Immersion Reimagined4K/60fps HDR VideosUnleash your true aerial potential. The 4K/60fps HDR on Avata 2 captures all the awesome of high-speed flight. In the goggles, you can adjust the sharpness and noise reduction levels for more finely tuned videos.
RockSteadyEquipped with DJI's latest stabilization algorithm, Avata 2 captures smooth, steady footage even when flying at high speeds or in windy conditions.RockSteady On | RockSteady Off
HorizonSteadyHorizonSteady handles horizontal rotations up to 360°, ensuring the captured footage remains locked on the horizon even if the drone turns sharply or sways dramatically.HorizonSteady On | HorizonSteady Off
155° Ultra-Wide-Angle FOVAmplify your vision and increase the immersion of low-altitude, high-speed flights. Avata 2 offers ultra-wide-angle, wide-angle, and normal-angle FOV options giving you the ability to adjust to the scenario.Ultra-Wide-Angle | Wide-Angle | Normal
10-bit D-Log MCapture rich detail in highlights and shadows and enhance content post-production opportunities while further streamlining color-grading.Standard Mode | 10-bit D-Log M Mode
Got You CoveredComprehensive SafetyThe updated integrated propeller guard design of Avata 2 makes it lighter and more agile, enabling it to navigate freely in tight spaces. [4] Releasing the accelerator on RC Motion 3 or pressing the lock button brings the drone to a halt, allowing you to handle unexpected situations calmly. In addition, the automatic Return to Home (RTH) function is initiated when the drone's battery is low or in case of signal loss, adding an extra layer of security.3D Preview | AR Preview
Advanced Positioning with New SensorsNew binocular fisheye sensors enable downward and backward visual positioning during low-altitude and indoor flights, enhancing flight stability and safety.
Turtle ModeAvata 2 can automatically flip itself back into takeoff position when upside down with Turtle mode enabled, so you can quickly get airborne again.
Excellence in EverythingFlight Time/Video TransmissionThe Sky's the Limit With Longer Flight. Avata 2 boasts a maximum flight time of 23 minutes and supports PD fast charging, so you can quickly recharge it and take to the skies again.The new DJI Avata 2 Two-Way Charging Hub features a power accumulation function, allowing the transfer of remaining power from multiple batteries to the one with the highest charge level, giving you an "extra battery" in critical moments.
O4 Video Transmission, Enhanced PerceptionDJI O4 video transmission's enhanced stability lets you fully immerse yourself in each flight and provides greater safety. Its two-transmitter, four-receiver, four-antenna design ensures strong anti-interference performance, and it boasts up to 13 km of maximum video transmission distance, a transmission latency as low as 24 ms, 1080p/100fps high-definition image quality, and a maximum transmission bitrate of 60Mbps.
Boundless Passion, Wireless SharingWatch the DJI Goggles 3 live feed from Avata 2 on your smart device's DJI Fly App. Connect up to 5 m away. Sharing the excitement of FPV just got easier, and learning how to fly is more accessible than ever.
Save More, Share MoreCapture and Edit SeamlesslyAvata 2 comes equipped with 46GB internal storage, capable of storing approximately 90 minutes of 1080p/60fps video, ensuring you capture the best parts of each flight.With Wi-Fi connectivity for fast file transfer to your phone, post-editing and sharing of your finished work is highly efficient.One-Tap VFX with LightCutThe LightCut app, connecting directly to DJI Avata 2 via Wi-Fi, allows you to intelligently add Sky VFX during post based on the flight trajectory captured in your videos, helping you easily create engaging aerial footage. Without the need to download the footage, the app offers editing and, combined with ‌One-Tap Edit, allows you to produce polished content in a snap effortlessly.


Sky VFX: After connecting the device and importing the footage, tap Sky VFX to add unique overlays, through-the-air text animations, virtual cockpits, and dashboard effects, enhancing the interactive fun and engagement of your immersive flight footage

One-Tap Edit: With AI's intelligent recognition of video types and themes, you can effortlessly filter through and select highlights with smooth camera work and exquisite composition. Coupled with a vast array of thematic templates, enabling you to produce polished content. The app also boasts intelligent sound effects, color restoration, one-click addition of device watermarks, and end credits, among other features

Wireless Connection: When Avata 2 is connected wirelessly to LightCut, you can preview the captured footage within the app and edit it without the need to download the footage, saving valuable space on your smartphone



Specifications
DJI Avata 2

Takeoff Weight: 377g Approx.
Dimensions: 185×212×64mm (L×W×H)
Max Ascent Speed: 6 m/s (Normal mode), 9 m/s (Sport mode)
Max Descent Speed: 6 m/s (Normal mode), 9 m/s (Sport mode)
Max Horizontal Speed (near sea level, no wind): 8 m/s (Normal mode), 16 m/s (Sport mode), 27 m/s (Manual mode)* No faster than 19 m/s with the Manual mode in the EU regions.

Max Takeoff Altitude: 5000m * Measured in a windless environment when taking off from an altitude of 5000 m and ascending vertically by 500 m, using Sport mode, and from 100% battery level until 20%. Data is for reference only. Always pay attention to reminders on the goggles' screens during your flight.

Max Flight Time: Approx. 23 mins * Measured when flying forward at a speed of 21.6 kph in a windless environment at sea level, with camera parameters set to 1080p/30fps, video mode off, and from 100% battery level until 0%. Data is for reference only. Always pay attention to reminders on the goggles' screens during your flight.
Max Hovering Time: Approx. 21 mins * ‌‌Measured when hovering in a windless environment at sea level, with camera parameters set to 1080p/30fps, video mode off, and from 100% battery level until 0%. Data is for reference only. Always pay attention to reminders on the goggles' screens during your flight.
Max Flight Distance: 13.0 km * ‌Measured when flying forward at a speed of 43.2 kph in a windless environment at sea level, with camera parameters set to 1080p/30fps, video mode off, and from 100% battery level until 0%. Data is for reference only. Always pay attention to reminders on the goggles' screens during your flight.
Max Wind Speed Resistance: 10.7 m/s (Level 5)
Operating Temperature: -10° to 40° C (14° to 104° F)
Global Navigation Satellite System: GPS + Galileo + BeiDou
Hovering accuracy range Vertical:

±0.1 m (with vision positioning)
±0.5 m (with GNSS positioning)

Horizontal:

±0.3 m (with vision positioning)
±1.5 m (with GNSS positioning)

Internal Storage: 46 GB


Camera

Image Sensor: 1/1.3-inch image sensor
Effective Pixels: 12 MP
Lens FOV: 155°
Format Equivalent: 12 mm
Aperture: f/2.8
Focus: 0.6 m to ∞
ISO Range: 100-25600 (Auto), 100-25600 (Manual)
Shutter Speed Video: 1/8000-1/30 s, Photo: 1/8000-1/50 s
Max Image Size: 4000×2256 (16∶9), 4000×3000 (4∶3)
Still Photography Mode: Single shot
Photo Format: JPEG
Video Resolution

-4K (4∶3): 3840×2880@30/50/60fps
-4K (16∶9): 3840×2160@30/50/60fps
-2.7K (4∶3): 2688×2016@30/50/60fps
-2.7K (16∶9): 2688×1512@30/50/120fps
-1080p (4∶3): 1440×1080@30/50/120fps
-1080p (16∶9): 1920×1080@30/50/120fps


Video Format: MP4 (H.264/H.265)
Max Video Bitrate: 130 Mbps
Supported File System: exFAT
Color Mode: Standard, D-Log M
Camera FOV: Supports normal mode, wide-angle mode, and ultra-wide-angle mode.
Camera EIS: Supports RockSteady 3.0+ and HorizonSteady, * Can be disabled *When stabilization is turned off, footage captured with the wide-angle view supports offline stabilization Gyroflow.

Gimbal

Stabilization: Single-axis mechanical gimbal (tilt)
Mechanical RangeC85: Tilt: -95° to 90°
Controllable Range: Tilt: -85° to 80°
Max Control Speed (tilt): 100°/s
Angular Vibration Range: ±0.01°
Electronic Roll Axis: Real-time screen correction is unavailable during recording, but can be applied to the footage recorded on the drone.

Sensing

Sensing Type: Downward and backward visual positioning
Downward

-ToF Effective Measurement Height: 10 m-Precise Hovering Range: 0.3-10 m-Measurement Range: 0.3-20 m-FOV: Horizontal 78°, Vertical 78°

Sensing Backward

-Measurement Range: 0.5-20 m-FOV: Horizontal 78°, Vertical 78°

Sensing Operating Environment

-Diffuse reflective surfaces with discernible patterns, diffuse reflectivity &gt 20% (such as concrete pavement)-Adequate lighting (lux &gt 15, normal indoor lighting conditions)
Video Transmission

Video Transmission System: O4
Live View Quality: 1080p@30/50/60/100fps
Operating Frequency:

-2.400-2.4835 GHz-5.170-5.250 GHz*-5.725-5.850 GHz** 5.170-5.250 GHz and 5.725-5.850 GHz can be used only in countries and regions where permitted by local laws and regulations.

Transmitter Power (EIRP):

-2.4 GHz＜33 dBm (FCC)＜20 dBm (CE/SRRC/MIC)-5.1 GHz&lt 23 dBm (CE)-5.8 GHz＜33 dBm (FCC)＜30 dBm (SRRC)&lt 14 dBm (CE)

Communication Bandwidth Max 60 MHz
Max Transmission Distance (unobstructed, free of interference)

-FCC: 13 km (subject to the aircraft's max flight distance)-CE: 10 km-SRRC: 10 km-MIC: 10 km* Measured in an unobstructed outdoor environment free of interference. The above data shows the farthest communication range for one-way, non-return flights under each standard. Always pay attention to RTH reminders on the goggles screen during your flight.

Max Transmission Distance (unobstructed, with interference)

-Strong Interference: Urban landscape, approx. 1.5-4 km-Medium Interference: Suburban landscape, approx. 4-10 km-Low Interference: Suburb/seaside, approx. 10-13 km* Data tested under FCC standard in unobstructed environments with typical interference. Used for reference purposes only and provides no guarantee for actual transmission distance.

Max Transmission Distance (obstructed, with interference)

-Low Interference and Obstructed by Buildings: approx. 0-0.5 km-Low Interference and Obstructed by Trees: approx. 0.5-3 km* Data tested under FCC standard in environments with typical low interference. Used for reference purposes only and provides no guarantee for actual transmission distance.

Max Download Speed: Wi-Fi: 30 MB/s

* Measured in a laboratory environment with little interference in countries/regions that support both 2.4 GHz and 5.8 GHz. Download speeds may vary depending on the actual conditions.

Lowest Latency With DJI Goggles 3:

-1080p/100fps Video Transmission Quality: 24 ms-1080p/60fps Video Transmission Quality: 40 ms

Max Video Bitrate: 60Mbps
Antennas: 4 antennas, 2T4R

Wi-Fi

ProtocolC156: 802.11a/b/g/n/ac
Operating Frequency: 2.400-2.4835 GHz, 5.725-5.850 GHz
Transmitter Power (EIRP):

-2.4 GHz&lt20 dBm (FCC／CE／SRRC／MIC)-5.8 GHz&lt20 dBm (FCC／SRRC)&lt 14 dBm (CE)
Bluetooth

Protocol: Bluetooth 5.0
Operating Frequency: 2.400-2.4835 GHz
Transmitter Power (EIRP): &lt10 dBm

Intelligent Flight Battery

Capacity: 2150 mAh
Weight: 145g Approx.
Standard Voltage: 14.76 V
Max Charging Voltage: 17 V
Battery Type: Li-ion
Energy: 31.7 Wh@0.5C
Charging Temperature: 5° to 40° C (41° to 104° F)
Charging Time:

-With Charging Hub (60W max charging power)From 0 to 100%: approx. 45 minFrom 10 to 90%: approx. 30 min-Directly Charging the Drone (30 W max charging power)From 0 to 100%: approx. 88 minFrom 10 to 90%: approx. 60 min
Charger

Recommended Charger: DJI 65W Portable Charger, DJI 65W Car Charger, USB Power Delivery charger

Recommended microSD Cards 

SanDisk Extreme PRO 32GB U3 A1 V30 microSDHC
Lexar Professional 1066x 64GB U3 A2 V30 microSDXC
Lexar Professional 1066x 128GB U3 A2 V30 microSDXC
Lexar Professional 1066x 256GB U3 A2 V30 microSDXC
Lexar Professional 1066x 512GB U3 A2 V30 microSDXC
Kingston CANVAS Go! Plus 64GB U3 A2 V30 microSDXC
Kingston CANVAS Go! Plus 128GB U3 A2 V30 microSDXC
Kingston CANVAS React Plus 64GB U3 A1 V90 microSDXC
Kingston CANVAS React Plus 128GB U3 A1 V90 microSDXC
Kingston CANVAS React Plus 256GB U3 A1 V90 microSDXC
Samsung EVO Plus 512GB U3 A2 V30 microSDXC


Includes

1x DJI AVATA 2
1x Flight Battery


Pre-Orders shipping ASAP! All products with batteries must be shipped by a ground shipping method. All Thrills and No Frills. Experience the Avata 2 and enjoy immersive flight. Check out our other RTF combos, all our pre-built quads and all of our DJI products! Features All Thrills, No Frills Immersive Flight Experienc

(PRE-ORDER) DJI AVATA 2 - Drone Only

DJI Avata 2 FPV DroneAll Thrills, No FrillsThe adrenaline-pumping DJI Avata 2 delivers an immersive FPV drone experience with improved imaging, safety, and battery life. Amp up the fun when you pair Avata 2 with the new DJI Goggles 3 and DJI RC Motion 3.Immersive Flight ExperienceIntuitive Motion ControlTight Shots in Super-Wide 4KEasy ACROBuilt-in Propeller GuardHassle-Free POV ContentDJI Goggles 3Representing a stunning visionary breakthroughDJI Goggles 3 now has Real View PiP (Picture-In-Picture). Observe your surroundings without removing the goggles, for more safety and immersion. The Micro-OLED high-definition display and ultra-low-latency transmission bring the world in to view.Flipping Awesome!Easy ACROSoar, dive, and roll for stunning aerial footage with a single push. Capturing epic FPV footage with DJI RC Motion 3 and Avata 2 is easier than ever.One-Push Flip360° front/back flip, adding fresh twists to your footage.One...

The best quality First Person View equipment. Free or discounted shipping on all orders.Drone Racing, RC Airplanes, FPV Cameras, FPV Goggles, Video Transmitters, RC Quads, Drone Antennas, Lipo Batteries, and Ground Station Equipment.All available for amateurs, schools, hobbyists, government, and wholesale buyers.

DJI Avata 2 (Drone Only) - RMRC

DJI Avata 2 (Drone Only)

Pre-Built Quad Kit Type

Pre-Built Quads and Kits

Quad Frame Size

Quad Type

DJI Avata 2 Fly More Combo RTF Kit

This DJI Avata 2 Combo includes the Avata 2 Drone, Goggles 3, Motion Controller 3, 1 Intelligent Flight battery, a charging hub, and everything you need to get in the air!
Check out our in-depth review below!
Features

Immersive Flight Experience
Intuitive Motion Control (when used with RC Motion 3 Controller)
Tight Shots in Super-Wide 4K
Easy ACRO 
Built-in Propeller Guard
Hassle-Free POV Content
Easy ACRO
Flip, Roll, 180° Drift
1/1.3″ CMOS Super-Wide-Angle Camera
4K/60fps HDR Videos 
10-bit D-Log M Color Mode
Downward/Backward Visual Positioning
23-Min Max Flight Time
The drone supports PD fast charging.
DJI O4 Video Transmission
Max Transmission Distance: 13 km
Max Transmission Bitrate: 60Mbps
46GB Large Internal Storage
High-Speed QuickTransfer

Specifications
DJI Avata 2 Drone

Takeoff Weight: Approx. 377 g
Dimensions: 185×212×64 mm (L×W×H)
Max Ascent Speed: ‌6 m/s (Normal mode), 9 m/s (Sport mode)
Max Descent Speed:
Max Horizontal Speed: (near sea level, no wind) 8 m/s (Normal mode), ‌16 m/s (Sport mode), 27 m/s (Manual mode)*
Max Flight Time: ‌Approx. 23 mins
Max Hovering Time: ‌Approx. 21 mins
Max Flight Distance: 13.0 km‌
Max Wind Speed Resistance: 10.7 m/s (Level 5)
Operating Temperature: -10° to 40° C (14° to 104° F)
Global Navigation Satellite System: GPS + Galileo + BeiDou
Hovering accuracy range: Vertical: ±0.1 m (with vision positioning), ±0.5 m (with GNSS positioning)Horizontal: ±0.3 m (with vision positioning), ±1.5 m (with GNSS positioning)
Internal Storage: 46 GB
Image Sensor: ‌1/1.3-inch image sensor
Effective Pixels: 12 MPLens ‌FOV: 155°Format Equivalent: 12 mm
Aperture: f/2.8
Focus: 0.6 m to ∞
ISO Range: 100-25600 (Auto), 100-25600 (Manual)
Shutter Speed Video: 1/8000-1/30 s
Photo: 1/8000-1/50 s
Max Image Size: 4000×2256 (16∶9), 4000×3000 (4∶3)
Still Photography Mode: Single shot
Photo Format: JPEG
Video Resolution 4K (4∶3): 3840×2880@30/50/60fps4K (16∶9): 3840×2160@30/50/60fps2.7K (4∶3): 2688×2016@30/50/60fps2.7K (16∶9): 2688×1512@30/50/120fps1080p (4∶3): 1440×1080@30/50/120fps1080p (16∶9): 1920×1080@30/50/120fps
Video Format: MP4 (H.264/H.265)Max Video Bitrate: 130 Mbps
Supported File System: exFAT
Color Mode: Standard, D-Log M
Camera FOV: Supports normal mode, wide-angle mode, and ultra-wide-angle mode.
EIS: Supports RockSteady 3.0+ and HorizonSteady, Can be disabled*
Stabilization: Single-axis mechanical gimbal (tilt)
Mechanical Range Tilt: -95° to 90°
Controllable Range Tilt: -85° to 80°
Max Control Speed (tilt): 100°/s
Angular Vibration Range: ±0.01°
Sensing Type: Downward and backward visual positioningDownward ToF Effective Measurement Height: 10 mPrecise Hovering Range: 0.3-10 mMeasurement Range: 0.3-20 mFOV: Horizontal 78°, Vertical 78°Backward Measurement Range: 0.5-20 mFOV: Horizontal 78°, Vertical 78°Adequate lighting: (lux &gt 15, normal indoor lighting conditions)
Video Transmission System: O4
Live View Quality: 1080p@30/50/60/100fps
Operating Frequency: 2.400-2.4835 GHz,5.170-5.250 GHz*,5.725-5.850 GHz*
Transmitter Power (EIRP):2.4 GHz: ＜33 dBm (FCC), ＜20 dBm (CE/SRRC/MIC)5.1 GHz: &lt 23 dBm (CE)5.8 GHz: ＜33 dBm (FCC),＜30 dBm (SRRC), &lt 14 dBm (CE)
Communication Bandwidth: Max 60 MHz
Max Transmission Distance: (unobstructed, free of interference) FCC: 13 km (subject to the aircraft's max flight distance), CE: 10 km, SRRC: 10 km, MIC: 10 km
Max Transmission Distance (unobstructed, with interference)Strong Interference: Urban landscape, approx. 1.5-4 kmMedium Interference: Suburban landscape, approx. 4-10 kmLow Interference: Suburb/seaside, approx. 10-13 kmMax Transmission Distance (obstructed, with interference) Low Interference and Obstructed by Buildings: approx. 0-0.5 kmLow Interference and Obstructed by Trees: approx. 0.5-3 km
Max Download Speed Wi-Fi: 30 MB/s*
Lowest Latency With DJI Goggles 3:1080p/100fps Video Transmission Quality: 24 ms1080p/60fps Video Transmission Quality: 40 ms‌
Max Video Bitrate: 60Mbps
Antennas: 4 antennas, 2T4R
Protocol: 802.11a/b/g/n/ac
Operating Frequency: 2.400-2.4835 GHz, 5.725-5.850 GHzTransmitter Power: (EIRP) 2.4 GHz: &lt20 dBm (FCC／CE／SRRC／MIC)5.8 GHz: &lt20 dBm (FCC／SRRC), &lt 14 dBm (CE)Protoco:l Bluetooth 5.0Operating Frequency 2.400-2.4835 GHzTransmitter Power (EIRP) &lt10 dBm

Battery

Capacity: 2150 mAh
Weight: Approx. 145 g
Standard Voltage: 14.76 V
Max Charging Voltage 17 V
Battery Type: Li-ion
Energy: 31.7 Wh@0.5C
Charging Temperature: 5° to 40° C (41° to 104° F)
Charging Time With Charging Hub: (60W max charging power):From 0 to 100%: approx. 45 min‌From 10 to 90%: approx. 30 min‌‌
Directly Charging the Drone (30 W max charging power):‌From 0 to 100%: approx. 88 min‌From 10 to 90%: approx. 60 min‌‌‌‌

Includes

1x DJI Avata 2 Drone
1x DJI Goggles 3
1x DJI Motion 3
1x DJI Avata 2 Intelligent Flight Battery
1x DJI Goggles 3 Foam Padding
1x DJI Goggles 3 Additional Forehead Pad
1x DJI Goggles 3 -2.0D Corrective Lenses (Pair)
2x DJI Avata 2 Propellers (Pair)
8x DJI Avata 2 Propeller Screw
1x DJI Avata 2 Gimbal Protector
1x USB-C OTG Cable

1x Type-C to Type-C PD Cable
1x Screwdriver


This DJI Avata 2 Combo includes the Avata 2 Drone, Goggles 3, Motion Controller 3, 1 Intelligent Flight battery, a charging hub, and everything you need to get in the air! Check out our in-depth review below! Features Immersive Flight Experience Intuitive Motion Control (when used with RC Motion 3 Controller) Tight Sho

(PRE-ORDER) DJI Avata 2 Fly More Combo with 1 Battery

This DJI Avata 2 Combo includes the Avata 2 Drone, Goggles 3, Motion Controller 3, 1 Intelligent Flight battery, a charging hub, and everything you need to get in the air! Check out our in-depth review below! Features Immersive Flight Experience Intuitive Motion Control (when used with RC Motion 3 Controller) Tight Shots in Super-Wide 4K Easy ACRO Built-in Propeller Guard Hassle-Free POV Content Easy ACRO Flip, Roll, 180° Drift 1/1.3″ CMOS Super-Wide-Angle Camera 4K/60fps HDR Videos 10-bit D-Log M Color Mode Downward/Backward Visual Positioning 23-Min Max Flight Time The drone supports PD fast charging. DJI O4 Video Transmission Max Transmission Distance: 13 km Max Transmission Bitrate: 60Mbps 46GB Large Internal Storage High-Speed QuickTransfer Specifications DJI Avata 2 Drone Takeoff Weight: Approx. 377 g Dimensions: 185×212×64 mm (L×W×H) Max Ascent Speed: ‌6 m/s (Normal mode), 9 m/s (Sport mode) Max

Experience an immersive flight with the DJI Avata 2 Fly More Combo, featuring intuitive motion control, super-wide 4K capture, and easy POV content creation.

DJI Avata 2 Fly More Combo w/ 1 Battery

Experience an immersive flight with the DJI Avata 2 Fly More Combo, featuring intuitive motion control, super-wide 4K capture, and easy POV content creation.&nbsp

Experience an immersive flight with the DJI Avata 2 Fly More Combo, featuring intuitive motion control, super-wide 4K capture, and easy POV content creation. 

DJI Avata 2 Fly More Combo w/ 3 Batteries

DJI Avata 2 Fly More Combo (Three Batteries) - RMRC

DJI Avata 2 Fly More Combo (Three Batteries)

DJI Avata 2 Fly More Combo (Single Battery) - RMRC

DJI Avata 2 Fly More Combo (Single Battery)

All products with batteries must be shipped by a ground shipping method.
Includes the DJI Avata 2 drone, Goggles 3, RC Motion 3, and more. This combo lets you quickly get started with Avata 2 and experience the joy of immersive flight.
Check out our other RTF combos, all our pre-built quads and all of our DJI products!
Features






All Thrills, No Frills

Immersive Flight Experience
Intuitive Motion Control
Tight Shots in Super-Wide 4K
Easy ACRO
Built-in Propeller Guard
Hassle-Free POV Content

Fully Experience Flight DJI Avata 2 delivers an adrenaline-pumping immersive FPV drone experience with improved imaging, safety, and battery life. Amp up the fun when you pair Avata 2 with the new DJI Goggles 3 and DJI RC Motion 3.DJI Goggles 3Visionary BreakthroughDJI Goggles 3 now has Real View PiP (Picture-In-Picture). Observe your surroundings without removing the goggles, for more safety and immersion. The Micro-OLED high-definition display and ultra-low-latency transmission bring the world in to view.
DJI RC Motion 3Feel Every FlightEffortlessly perform difficult aerial acrobatics with DJI RC Motion 3. New pilots can now perform spectacular flips, drifts, and other captivating maneuvers.
Easy ACROSoar, dive, and roll for stunning aerial footage with a single push. Capturing epic FPV footage with DJI RC Motion 3 and Avata 2 is easier than ever.


One-Push Flip: 360° front/back flip, adding fresh twists to your footage.

One-Push Roll: Roll 360° left/right, turning any shot from meh to magic.


One-Push 180° Drift: High-speed lateral drifts to yaw spin 180° past objects and swiftly pull away, achieving dramatic visuals.

Tight Shots in Super-Wide 4K Create breathtaking visuals with Avata 2's 155° FOV and its ability to swiftly approach and pull away from subjects. New pilots can quickly master aerobatic shots and capture fast-moving dynamic low-altitude shots that other drones can't.

155° Ultra-Wide-Angle FOV of Avata 2
82° Standard View of Camera Drones

1/1.3-inch Image SensorThe upgraded 1/1.3-inch image sensor expands the captured dynamic range, handling low-light conditions more effectively to capture outstanding footage on every flight.

Effective Pixels: 12 MP
Offline Stabilization: Gyroflow

Immersion Reimagined4K/60fps HDR VideosUnleash your true aerial potential. The 4K/60fps HDR on Avata 2 captures all the awesome of high-speed flight. In the goggles, you can adjust the sharpness and noise reduction levels for more finely tuned videos.
RockSteadyEquipped with DJI's latest stabilization algorithm, Avata 2 captures smooth, steady footage even when flying at high speeds or in windy conditions.RockSteady On | RockSteady Off
HorizonSteadyHorizonSteady handles horizontal rotations up to 360°, ensuring the captured footage remains locked on the horizon even if the drone turns sharply or sways dramatically.HorizonSteady On | HorizonSteady Off
155° Ultra-Wide-Angle FOVAmplify your vision and increase the immersion of low-altitude, high-speed flights. Avata 2 offers ultra-wide-angle, wide-angle, and normal-angle FOV options giving you the ability to adjust to the scenario.Ultra-Wide-Angle | Wide-Angle | Normal
10-bit D-Log MCapture rich detail in highlights and shadows and enhance content post-production opportunities while further streamlining color-grading.Standard Mode | 10-bit D-Log M Mode
Got You CoveredComprehensive SafetyThe updated integrated propeller guard design of Avata 2 makes it lighter and more agile, enabling it to navigate freely in tight spaces. Releasing the accelerator on RC Motion 3 or pressing the lock button brings the drone to a halt, allowing you to handle unexpected situations calmly. In addition, the automatic Return to Home (RTH) function is initiated when the drone's battery is low or in case of signal loss, adding an extra layer of security.3D Preview | AR Preview
Advanced Positioning with New SensorsNew binocular fisheye sensors enable downward and backward visual positioning during low-altitude and indoor flights, enhancing flight stability and safety.
Turtle ModeAvata 2 can automatically flip itself back into takeoff position when upside down with Turtle mode enabled, so you can quickly get airborne again.
Excellence in EverythingFlight Time/Video TransmissionThe Sky's the Limit With Longer Flight. Avata 2 boasts a maximum flight time of 23 minutes and supports PD fast charging, so you can quickly recharge it and take to the skies again.The new DJI Avata 2 Two-Way Charging Hub features a power accumulation function, allowing the transfer of remaining power from multiple batteries to the one with the highest charge level, giving you an "extra battery" in critical moments.
O4 Video Transmission, Enhanced PerceptionDJI O4 video transmission's enhanced stability lets you fully immerse yourself in each flight and provides greater safety. Its two-transmitter, four-receiver, four-antenna design ensures strong anti-interference performance, and it boasts up to 13 km of maximum video transmission distance, a transmission latency as low as 24 ms, 1080p/100fps high-definition image quality, and a maximum transmission bitrate of 60Mbps.
Boundless Passion, Wireless SharingWatch the DJI Goggles 3 live feed from Avata 2 on your smart device's DJI Fly App. Connect up to 5 m away. Sharing the excitement of FPV just got easier, and learning how to fly is more accessible than ever.
Save More, Share MoreCapture and Edit SeamlesslyAvata 2 comes equipped with 46GB internal storage, capable of storing approximately 90 minutes of 1080p/60fps video, ensuring you capture the best parts of each flight.With Wi-Fi connectivity for fast file transfer to your phone, post-editing and sharing of your finished work is highly efficient.One-Tap VFX with LightCutThe LightCut app, connecting directly to DJI Avata 2 via Wi-Fi, allows you to intelligently add Sky VFX during post based on the flight trajectory captured in your videos, helping you easily create engaging aerial footage. Without the need to download the footage, the app offers editing and, combined with ‌One-Tap Edit, allows you to produce polished content in a snap effortlessly.


Sky VFX: After connecting the device and importing the footage, tap Sky VFX to add unique overlays, through-the-air text animations, virtual cockpits, and dashboard effects, enhancing the interactive fun and engagement of your immersive flight footage

One-Tap Edit: With AI's intelligent recognition of video types and themes, you can effortlessly filter through and select highlights with smooth camera work and exquisite composition. Coupled with a vast array of thematic templates, enabling you to produce polished content. The app also boasts intelligent sound effects, color restoration, one-click addition of device watermarks, and end credits, among other features

Wireless Connection: When Avata 2 is connected wirelessly to LightCut, you can preview the captured footage within the app and edit it without the need to download the footage, saving valuable space on your smartphone



Specifications
DJI Avata 2

Takeoff Weight: 377g Approx.
Dimensions: 185×212×64mm (L×W×H)
Max Ascent Speed: 6 m/s (Normal mode), 9 m/s (Sport mode)
Max Descent Speed: 6 m/s (Normal mode), 9 m/s (Sport mode)
Max Horizontal Speed (near sea level, no wind): 8 m/s (Normal mode), 16 m/s (Sport mode), 27 m/s (Manual mode)* No faster than 19 m/s with the Manual mode in the EU regions.

Max Takeoff Altitude: 5000m * Measured in a windless environment when taking off from an altitude of 5000 m and ascending vertically by 500 m, using Sport mode, and from 100% battery level until 20%. Data is for reference only. Always pay attention to reminders on the goggles' screens during your flight.

Max Flight Time: Approx. 23 mins * Measured when flying forward at a speed of 21.6 kph in a windless environment at sea level, with camera parameters set to 1080p/30fps, video mode off, and from 100% battery level until 0%. Data is for reference only. Always pay attention to reminders on the goggles' screens during your flight.
Max Hovering Time: Approx. 21 mins * ‌‌Measured when hovering in a windless environment at sea level, with camera parameters set to 1080p/30fps, video mode off, and from 100% battery level until 0%. Data is for reference only. Always pay attention to reminders on the goggles' screens during your flight.
Max Flight Distance: 13.0 km * ‌Measured when flying forward at a speed of 43.2 kph in a windless environment at sea level, with camera parameters set to 1080p/30fps, video mode off, and from 100% battery level until 0%. Data is for reference only. Always pay attention to reminders on the goggles' screens during your flight.
Max Wind Speed Resistance: 10.7 m/s (Level 5)
Operating Temperature: -10° to 40° C (14° to 104° F)
Global Navigation Satellite System: GPS + Galileo + BeiDou
Hovering accuracy range Vertical:

±0.1 m (with vision positioning)
±0.5 m (with GNSS positioning)

Horizontal:

±0.3 m (with vision positioning)
±1.5 m (with GNSS positioning)

Internal Storage: 46 GB


Camera

Image Sensor: 1/1.3-inch image sensor
Effective Pixels: 12 MP
Lens FOV: 155°
Format Equivalent: 12 mm
Aperture: f/2.8
Focus: 0.6 m to ∞
ISO Range: 100-25600 (Auto), 100-25600 (Manual)
Shutter Speed Video: 1/8000-1/30 s, Photo: 1/8000-1/50 s
Max Image Size: 4000×2256 (16∶9), 4000×3000 (4∶3)
Still Photography Mode: Single shot
Photo Format: JPEG
Video Resolution

-4K (4∶3): 3840×2880@30/50/60fps
-4K (16∶9): 3840×2160@30/50/60fps
-2.7K (4∶3): 2688×2016@30/50/60fps
-2.7K (16∶9): 2688×1512@30/50/120fps
-1080p (4∶3): 1440×1080@30/50/120fps
-1080p (16∶9): 1920×1080@30/50/120fps


Video Format: MP4 (H.264/H.265)
Max Video Bitrate: 130 Mbps
Supported File System: exFAT
Color Mode: Standard, D-Log M
Camera FOV: Supports normal mode, wide-angle mode, and ultra-wide-angle mode.
Camera EIS: Supports RockSteady 3.0+ and HorizonSteady, * Can be disabled *When stabilization is turned off, footage captured with the wide-angle view supports offline stabilization Gyroflow.

Gimbal

Stabilization: Single-axis mechanical gimbal (tilt)
Mechanical RangeC85: Tilt: -95° to 90°
Controllable Range: Tilt: -85° to 80°
Max Control Speed (tilt): 100°/s
Angular Vibration Range: ±0.01°
Electronic Roll Axis: Real-time screen correction is unavailable during recording, but can be applied to the footage recorded on the drone.

Sensing

Sensing Type: Downward and backward visual positioning
Downward

-ToF Effective Measurement Height: 10 m-Precise Hovering Range: 0.3-10 m-Measurement Range: 0.3-20 m-FOV: Horizontal 78°, Vertical 78°

Sensing Backward

-Measurement Range: 0.5-20 m-FOV: Horizontal 78°, Vertical 78°

Sensing Operating Environment

-Diffuse reflective surfaces with discernible patterns, diffuse reflectivity &gt 20% (such as concrete pavement)-Adequate lighting (lux &gt 15, normal indoor lighting conditions)
Video Transmission

Video Transmission System: O4
Live View Quality: 1080p@30/50/60/100fps
Operating Frequency:

-2.400-2.4835 GHz-5.170-5.250 GHz*-5.725-5.850 GHz** 5.170-5.250 GHz and 5.725-5.850 GHz can be used only in countries and regions where permitted by local laws and regulations.

Transmitter Power (EIRP):

-2.4 GHz＜33 dBm (FCC)＜20 dBm (CE/SRRC/MIC)-5.1 GHz&lt 23 dBm (CE)-5.8 GHz＜33 dBm (FCC)＜30 dBm (SRRC)&lt 14 dBm (CE)

Communication Bandwidth Max 60 MHz
Max Transmission Distance (unobstructed, free of interference)

-FCC: 13 km (subject to the aircraft's max flight distance)-CE: 10 km-SRRC: 10 km-MIC: 10 km* Measured in an unobstructed outdoor environment free of interference. The above data shows the farthest communication range for one-way, non-return flights under each standard. Always pay attention to RTH reminders on the goggles screen during your flight.

Max Transmission Distance (unobstructed, with interference)

-Strong Interference: Urban landscape, approx. 1.5-4 km-Medium Interference: Suburban landscape, approx. 4-10 km-Low Interference: Suburb/seaside, approx. 10-13 km* Data tested under FCC standard in unobstructed environments with typical interference. Used for reference purposes only and provides no guarantee for actual transmission distance.

Max Transmission Distance (obstructed, with interference)

-Low Interference and Obstructed by Buildings: approx. 0-0.5 km-Low Interference and Obstructed by Trees: approx. 0.5-3 km* Data tested under FCC standard in environments with typical low interference. Used for reference purposes only and provides no guarantee for actual transmission distance.

Max Download Speed: Wi-Fi: 30 MB/s

* Measured in a laboratory environment with little interference in countries/regions that support both 2.4 GHz and 5.8 GHz. Download speeds may vary depending on the actual conditions.

Lowest Latency With DJI Goggles 3:

-1080p/100fps Video Transmission Quality: 24 ms-1080p/60fps Video Transmission Quality: 40 ms

Max Video Bitrate: 60Mbps
Antennas: 4 antennas, 2T4R

Wi-Fi

ProtocolC156: 802.11a/b/g/n/ac
Operating Frequency: 2.400-2.4835 GHz, 5.725-5.850 GHz
Transmitter Power (EIRP):

-2.4 GHz&lt20 dBm (FCC／CE／SRRC／MIC)-5.8 GHz&lt20 dBm (FCC／SRRC)&lt 14 dBm (CE)
Bluetooth

Protocol: Bluetooth 5.0
Operating Frequency: 2.400-2.4835 GHz
Transmitter Power (EIRP): &lt10 dBm

Intelligent Flight Battery

Capacity: 2150 mAh
Weight: 145g Approx.
Standard Voltage: 14.76 V
Max Charging Voltage: 17 V
Battery Type: Li-ion
Energy: 31.7 Wh@0.5C
Charging Temperature: 5° to 40° C (41° to 104° F)
Charging Time:

-With Charging Hub (60W max charging power)From 0 to 100%: approx. 45 minFrom 10 to 90%: approx. 30 min-Directly Charging the Drone (30 W max charging power)From 0 to 100%: approx. 88 minFrom 10 to 90%: approx. 60 min
Charger

Recommended Charger: DJI 65W Portable Charger, DJI 65W Car Charger, USB Power Delivery charger

Battery Charging Hub

Input: 5-20 V, max 3 A
Output (power accumulation): Max 65 W
Output (charging): Max 17 V
Output (USB): 5 V, 2 A
Charging Type: Three batteries charged in sequence
Compatibility: DJI Avata 2 Intelligent Flight Battery

Recommended microSD Cards 

SanDisk Extreme PRO 32GB U3 A1 V30 microSDHC
Lexar Professional 1066x 64GB U3 A2 V30 microSDXC
Lexar Professional 1066x 128GB U3 A2 V30 microSDXC
Lexar Professional 1066x 256GB U3 A2 V30 microSDXC
Lexar Professional 1066x 512GB U3 A2 V30 microSDXC
Kingston CANVAS Go! Plus 64GB U3 A2 V30 microSDXC
Kingston CANVAS Go! Plus 128GB U3 A2 V30 microSDXC
Kingston CANVAS React Plus 64GB U3 A1 V90 microSDXC
Kingston CANVAS React Plus 128GB U3 A1 V90 microSDXC
Kingston CANVAS React Plus 256GB U3 A1 V90 microSDXC
Samsung EVO Plus 512GB U3 A2 V30 microSDXC


Includes

1x DJI AVATA 2
1x DJI Goggles 3
1x RC Motion 3
1x Flight Battery
2x Propeller Sets
1x Screwdriver
1x Lanyard
1x -2.0D Corrective lenses (Set)
1x Additional Forehead Pad
1x USB-C OTG Cable
1x Type-C USB Cable
1x Manuals


All products with batteries must be shipped by a ground shipping method. Includes the DJI Avata 2 drone, Goggles 3, RC Motion 3, and more. This combo lets you quickly get started with Avata 2 and experience the joy of immersive flight. Check out our other RTF combos, all our pre-built quads and all of our DJI products!

DJI AVATA 2 Fly More Combo RTF Kit - Single Battery

The adrenaline-pumping DJI Avata 2 delivers an immersive FPV drone experience with improved imaging, safety, and battery life. Amp up the fun when you pair Avata 2 with the new DJI Goggles 3 and DJI RC Motion 3. DJI Avata 2 Fly More Combo (Three Battery) Compared to the DJI Avata 2 Fly More Combo (Single Battery), this

(PRE-ORDER) DJI Avata 2 Fly More Combo RTF Kit with Goggles 3 and RC Motion 3 Controller - Three Battery

GEPRC

GEPRC BNF CineLog35 V2 Analog 3.5" Cinewhoop - 2.4GHz ELRS, GPS

Recommended GEPRC Storm 6S 1300mAh 120C Lipo Battery for CineLog35 V2.

GEPRC CineLog35 V2 Analog FPV Drone - GEPRC

GEPRC CineLog35 V2 Analog FPV Drone



















Experience unrivaled performance with the GEPRC CineLog35 V2 6S 3.5&quot Cinewhoop. This powerful model features an analog &ampamp micro cam, as well as ELRS 2.4GHz technology, for streamlined flight capabilities and less chance of a fail safe. Fly with confidence as you capture flawless footage with every launch.








Check out our other pre-built quads, as well as the rest of our GEPRC selection.


















Features

New appearance design, strengthening carbon plate, hollow design, injection protection frame, noise reduction design, flight safety, silent.
Adopts the GEP F722-45A AIO V2 high performance flight controller.
SPEEDX2 2105.5 motor with HQ DT90 propeller, stable power output, and smooth flight feel.

Power cable using XT60E1-M plug and carbon plate integrated design, convenient application.
Battery installation method using a tie with 7075 aluminum parts fixed, solid and stable.
Carefully tuned 3.5-inch cinematic FPV quad with flexible and delicate flight feeling.
Pre-Installed with a M8U GPS



 


Specifications

Model: Cinelog35 V2 Analog

Frame: GEP-CL35 V2

Wheelbase: 142mm

Gimbal Plate: 2.0mm

Top Plate: 3.5mm

Bottom Plate: 1.5mm

FC system: GEP-F722-45A AIO V2

MCU: STM32F722RET6

Gyro: ICM 42688-P

OSD: Betaflight OSD w/AT7456E chip

ESC: 8Bit 45A

VTX: GEPRC RAD 1W(UFL)

Camera: Caddx Ratel2

Antenna: GEPRC Peano 5.8 RHCP UFL

Motor: SPEEDX2 2105.5-2150KV (6S)

Propeller: HQProp D-T90MM

GPS: GEP-M8U

Receiver: ELRS2.4G

Weight: 262g
Recommended battery: LiPo 1050mah-1300mah

Flight time: 5′00″ - 8′ 30″

Includes

1x GEPRC BNF CineLog35 V2 Analog 6S 3.5&quot Cinewhoop - ELRS 2.4GHz (GPS)
2x HQProp D-T90MM（2 pairs）

2x M20 x 250mm battery strap

2x Battery Silicone Pads

1x Set of screws

1x L-shaped screwdriver (1.5mm)

1x L-shaped screwdriver (2mm)

1x L-shaped screwdriver (3mm)

1x M5 wrench

1x plastic tweezers

1x Antenna fixed tube (pair)

1x Keychain

1x GP Camera Mounting Base

1x Naked GP Camera Mounting Base

1x Antenna Mounting Base


Experience unrivaled performance with the GEPRC CineLog35 V2 6S 3.5" Cinewhoop. This powerful model features an analog &amp; micro cam, as well as ELRS 2.4GHz technology, for streamlined flight capabilities and less chance of a fail safe. Fly with confidence as you capture flawless footage with every launch. Check out 

GEPRC BNF CineLog35 V2 Analog 6S 3.5" Cinewhoop - ELRS 2.4GHz (GPS) from WREKD Co.

GEPRC BNF CineLog35 V2 Analog 6S 3.5

GEPRC BNF CineLog35 V2 Analog 6S 3.5" Cinewhoop - ELRS 2.4GHz (GPS)



















Experience unrivaled performance with the GEPRC CineLog35 V2 6S 3.5" Cinewhoop. This powerful model features an analog &amp micro cam, as well as ELRS 2.4GHz technology, for streamlined flight capabilities and less chance of a fail safe. Fly with confidence as you capture flawless footage with every launch.








Check out our other pre-built quads, as well as the rest of our GEPRC selection.


















Features

New appearance design, strengthening carbon plate, hollow design, injection protection frame, noise reduction design, flight safety, silent.
Adopts the GEP F722-45A AIO V2 high performance flight controller.
SPEEDX2 2105.5 motor with HQ DT90 propeller, stable power output, and smooth flight feel.

Power cable using XT60E1-M plug and carbon plate integrated design, convenient application.
Battery installation method using a tie with 7075 aluminum parts fixed, solid and stable.
Carefully tuned 3.5-inch cinematic FPV quad with flexible and delicate flight feeling.
Pre-Installed with a M8U GPS



 


Specifications

Model: Cinelog35 V2 Analog

Frame: GEP-CL35 V2

Wheelbase: 142mm

Gimbal Plate: 2.0mm

Top Plate: 3.5mm

Bottom Plate: 1.5mm

FC system: GEP-F722-45A AIO V2

MCU: STM32F722RET6

Gyro: ICM 42688-P

OSD: Betaflight OSD w/AT7456E chip

ESC: 8Bit 45A

VTX: GEPRC RAD 1W(UFL)

Camera: Caddx Ratel2

Antenna: GEPRC Peano 5.8 RHCP UFL

Motor: SPEEDX2 2105.5-2150KV (6S)

Propeller: HQProp D-T90MM

GPS: GEP-M8U

Receiver: ELRS2.4G

Weight: 262g
Recommended battery: LiPo 1050mah-1300mah

Flight time: 5′00″ - 8′ 30″

Includes

1x GEPRC BNF CineLog35 V2 Analog 6S 3.5" Cinewhoop - ELRS 2.4GHz (GPS)
2x HQProp D-T90MM（2 pairs）

2x M20 x 250mm battery strap

2x Battery Silicone Pads

1x Set of screws

1x L-shaped screwdriver (1.5mm)

1x L-shaped screwdriver (2mm)

1x L-shaped screwdriver (3mm)

1x M5 wrench

1x plastic tweezers

1x Antenna fixed tube (pair)

1x Keychain

1x GP Camera Mounting Base

1x Naked GP Camera Mounting Base

1x Antenna Mounting Base


Gathering the experience and evolution of the GEPRC team in all aspects, CineLog35 V2 is finally launched to the market with better performance. CineLog35 v2 version integrated with O3 VTX. The CineLog35 V2 version of the main carbon plate and injection protection frame increased the 7075 aluminum column for structural

GEPRC CineLog35 V2 Analog GPS 3.5

iFlight

iFlight BNF Helion 10 6S 10" HD Cinematic Long Range Quad - DJI O3 Air Unit, ELRS 2.4GHz, GPS

HELION - The Long Range flagship by 2RAW and Flight.&nbsp

HELION - The Long Range flagship by 2RAW and Flight. 

iFlight 2Raw Helion 10 Long Range 10" 6S BNF HD w/ DJI O3

iFlight 2Raw Helion 10 Long Range 10&quot 6S BNF HD w/ DJI O3

IFLIGHT

This drone was built to redefine Long Range. In order to meet the rising demands for more range, and more flight time while maintaining enough weight, to have excellent stability in even the windiest of conditions. With a prop size of 10 inches, Helion is not only capable of effectively carrying large (Recommended, 4500mAh Lipo and above) batteries but also ensuring great efficiency with ample power. You will have better dive recovery and more overall control than traditional long-range drones. Its unique aerodynamic shell allows for easy maintenance while protecting the cores of the power train. Helion’s distinct frame design was scientifically optimized to balance stability, weight, and rigidity.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products 
Features


Optimised Motors &amp PropellerThis latest XING motor was optimised between thrust and efficiency. Perfectly tuned to the 10 inch Gemfan propellers.


Aero-ShellThe unique aerodynamic shell allows for easy maintenance while protecting the cores of the power train. Users can simply open and close the shell when working on the drone. The idea was to protect the inside but give people full access when maintenance work is being performed on the drone.


Innovative A-Frame for Maximum PerformanceThe frame was scientifically optimised and tested over months to find the balance between stability and weight. The A-Frame design minimises vibrations as well as torsion, one of the biggest problems with larger drones.


USB-C PowerA USB-C Plug was added so you can power your action cam when running out of power. This was also built in for potential upcoming new small cameras making Helion more future proof


DJI O3 HD Air Unit Low-Latency Digital TransmissionUp to 10 km video transmission range, enjoy a crisp and smooth real-time view in your goggles, even in environments with interference. (Source DJI)


4K Stabilized Video with 155° Ultra-Wide AngleTogether with high-grade imaging performance, it delivers exceptional visuals that will keep your audience on the edge of their seats. (Source DJI)


GPS Pre-Installed for More Safety at A DistanceGPS functionality to find your way back on those ultra long range missions. Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour Setup instructions included). Custom iFlight 100mm LR antenna for best signal coverage even at long distances.





Specifications

Product Name: Helion10 O3 6S HD

FC: BLITZ F7 Flight Controller

ESC: BLITZ E55 4-IN-1 2-6S 55A ESC

Video Transmission: DJI O3 Air Unit

Geometry: A-Frame

Frame: 418mm wheelbase

Motor: XING2 3110 900KV motors

Prop: GEMFAN 1050 propellers

Weight: 970±20g (Without Battery)

Dimensions (L×W×H)：324x264x63mm

Max Speed: 140km/h

Maximum Takeoff Altitude: 7000 m

Max Hover Time: Approx. 26mins with 6S Lipo 5600mAh battery / 30mins with 6S
8000mAh Li-ion battery

Max Cruising Time: Approx. 23mins with 6S Lipo 5600mAh battery / 26mins with
6S 8000mAh Li-ion battery

Operating Temperature Range: -20° to 40° C

Antennas: Dual Antennas

GNSS: GPS+SBAS+Galileo+QZSS+Glonass

Video Transmission 

Product Name: DJI O3 Air Unit

Weight: Approx. 36.4 grams（headband included）

Dimensions (L×W×H): L32.5x W30.5xH 14.5mm

Communication Bandwidth： Max 40 MHz

FOV (single screen): 155°

Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz

End-to-End Latency

With DJI FPV Goggles V2:

810p/120fps Video Transmission Quality: The latency is lower than 28 ms.

810p/60fps Video Transmission Quality: The latency is lower than 40 ms.

With DJI Goggles 2:

1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.

1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.

Max Video Transmission Bitrate: 50 Mbps

Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)

Operating Temperature Range: -10º to 40º C (14° to 104° F)

Power Input: 7.4-26.4 V

Audio Transmission: N/A

END-TO-END LATENCY

With DJI FPV Goggles V2:

810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.

With DJI Goggles 2:

1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.


 Includes

1x Helion 10 6S HD

2x Battery pad

2x GEMFAN 1050 propellers(Pairs)

2x Battery strap

1xx Screw bag


This drone was built to redefine Long Range. In order to meet the rising demands for more range, and more flight time while maintaining enough weight, to have excellent stability in even the windiest of conditions. With a prop size of 10 inches, Helion is not only capable of effectively carrying large (Recommended, 450

iFlight BNF Helion 10 6S 10" HD Cinematic Long Range Quad w/DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz (GPS)

iFlight BNF Helion 10 6S 10" HD Cinematic Long Range Quad w/DJI O3 Air

RaceDayQuads

Pre-Orders shipping ASAP!
This drone was built to redefine Long Range. In order to meet the rising demands for more range, and more flight time while maintaining enough weight, to have excellent stability in even the windiest of conditions. With a prop size of 10 inches, Helion is not only capable of effectively carrying large (Recommended, 4500mAh Lipo and above) batteries but also ensuring great efficiency with ample power. You will have better dive recovery and more overall control than traditional long-range drones. Its unique aerodynamic shell allows for easy maintenance while protecting the cores of the power train. Helion’s distinct frame design was scientifically optimized to balance stability, weight, and rigidity.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products 
Features


Optimised Motors &amp PropellerThis latest XING motor was optimised between thrust and efficiency. Perfectly tuned to the 10 inch Gemfan propellers.


Aero-ShellThe unique aerodynamic shell allows for easy maintenance while protecting the cores of the power train. Users can simply open and close the shell when working on the drone. The idea was to protect the inside but give people full access when maintenance work is being performed on the drone.


Innovative A-Frame for Maximum PerformanceThe frame was scientifically optimised and tested over months to find the balance between stability and weight. The A-Frame design minimises vibrations as well as torsion, one of the biggest problems with larger drones.


USB-C PowerA USB-C Plug was added so you can power your action cam when running out of power. This was also built in for potential upcoming new small cameras making Helion more future proof


DJI O3 HD Air Unit Low-Latency Digital TransmissionUp to 10 km video transmission range, enjoy a crisp and smooth real-time view in your goggles, even in environments with interference. (Source DJI)


4K Stabilized Video with 155° Ultra-Wide AngleTogether with high-grade imaging performance, it delivers exceptional visuals that will keep your audience on the edge of their seats. (Source DJI)


GPS Pre-Installed for More Safety at A DistanceGPS functionality to find your way back on those ultra long range missions. Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour Setup instructions included). Custom iFlight 100mm LR antenna for best signal coverage even at long distances.





Specifications

Product Name: Helion10 O3 6S HD

FC: BLITZ F7 Flight Controller

ESC: BLITZ E55 4-IN-1 2-6S 55A ESC

Video Transmission: DJI O3 Air Unit

Geometry: A-Frame

Frame: 418mm wheelbase

Motor: XING2 3110 900KV motors

Prop: GEMFAN 1050 propellers

Weight: 970±20g (Without Battery)

Dimensions (L×W×H)：324x264x63mm

Max Speed: 140km/h

Maximum Takeoff Altitude: 7000 m

Max Hover Time: Approx. 26mins with 6S Lipo 5600mAh battery / 30mins with 6S
8000mAh Li-ion battery

Max Cruising Time: Approx. 23mins with 6S Lipo 5600mAh battery / 26mins with
6S 8000mAh Li-ion battery

Operating Temperature Range: -20° to 40° C

Antennas: Dual Antennas

GNSS: GPS+SBAS+Galileo+QZSS+Glonass

Video Transmission 

Product Name: DJI O3 Air Unit

Weight: Approx. 36.4 grams（headband included）

Dimensions (L×W×H): L32.5x W30.5xH 14.5mm

Communication Bandwidth： Max 40 MHz

FOV (single screen): 155°

Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz

End-to-End Latency

With DJI FPV Goggles V2:

810p/120fps Video Transmission Quality: The latency is lower than 28 ms.

810p/60fps Video Transmission Quality: The latency is lower than 40 ms.

With DJI Goggles 2:

1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.

1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.

Max Video Transmission Bitrate: 50 Mbps

Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)

Operating Temperature Range: -10º to 40º C (14° to 104° F)

Power Input: 7.4-26.4 V

Audio Transmission: N/A

END-TO-END LATENCY

With DJI FPV Goggles V2:

810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.

With DJI Goggles 2:

1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.


 Includes

1x Helion 10 6S HD

2x Battery pad

2x GEMFAN 1050 propellers(Pairs)

2x Battery strap

1xx Screw bag


Pre-Orders shipping ASAP! This drone was built to redefine Long Range. In order to meet the rising demands for more range, and more flight time while maintaining enough weight, to have excellent stability in even the windiest of conditions. With a prop size of 10 inches, Helion is not only capable of effectively carryi

iFlight BNF Helion 10 6S 10

This drone was built to redefine Long Range. In order to meet the rising demands for more range, and more flight time while maintaining enough weight, to have excellent stability in even the windiest of conditions. With a prop size of 10 inches, Helion is not only capable of effectively carrying large (Recommended, 4500mAh Lipo and above) batteries but also ensuring great efficiency with ample power. You will have better dive recovery and more overall control than traditional long-range drones. Its unique aerodynamic shell allows for easy maintenance while protecting the cores of the power train. Helion’s distinct frame design was scientifically optimized to balance stability, weight, and rigidity.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products 
Features


Optimised Motors &ampamp PropellerThis latest XING motor was optimised between thrust and efficiency. Perfectly tuned to the 10 inch Gemfan propellers.


Aero-ShellThe unique aerodynamic shell allows for easy maintenance while protecting the cores of the power train. Users can simply open and close the shell when working on the drone. The idea was to protect the inside but give people full access when maintenance work is being performed on the drone.


Innovative A-Frame for Maximum PerformanceThe frame was scientifically optimised and tested over months to find the balance between stability and weight. The A-Frame design minimises vibrations as well as torsion, one of the biggest problems with larger drones.


USB-C PowerA USB-C Plug was added so you can power your action cam when running out of power. This was also built in for potential upcoming new small cameras making Helion more future proof


DJI O3 HD Air Unit Low-Latency Digital TransmissionUp to 10 km video transmission range, enjoy a crisp and smooth real-time view in your goggles, even in environments with interference. (Source DJI)


4K Stabilized Video with 155° Ultra-Wide AngleTogether with high-grade imaging performance, it delivers exceptional visuals that will keep your audience on the edge of their seats. (Source DJI)


GPS Pre-Installed for More Safety at A DistanceGPS functionality to find your way back on those ultra long range missions. Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour Setup instructions included). Custom iFlight 100mm LR antenna for best signal coverage even at long distances.





Specifications

Product Name: Helion10 O3 6S HD

FC: BLITZ F7 Flight Controller

ESC: BLITZ E55 4-IN-1 2-6S 55A ESC

Video Transmission: DJI O3 Air Unit

Geometry: A-Frame

Frame: 418mm wheelbase

Motor: XING2 3110 900KV motors

Prop: GEMFAN 1050 propellers

Weight: 970±20g (Without Battery)

Dimensions (L×W×H)：324x264x63mm

Max Speed: 140km/h

Maximum Takeoff Altitude: 7000 m

Max Hover Time: Approx. 26mins with 6S Lipo 5600mAh battery / 30mins with 6S
8000mAh Li-ion battery

Max Cruising Time: Approx. 23mins with 6S Lipo 5600mAh battery / 26mins with
6S 8000mAh Li-ion battery

Operating Temperature Range: -20° to 40° C

Antennas: Dual Antennas

GNSS: GPS+SBAS+Galileo+QZSS+Glonass

Video Transmission 

Product Name: DJI O3 Air Unit

Weight: Approx. 36.4 grams（headband included）

Dimensions (L×W×H): L32.5x W30.5xH 14.5mm

Communication Bandwidth： Max 40 MHz

FOV (single screen): 155°

Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz

End-to-End Latency

With DJI FPV Goggles V2:

810p/120fps Video Transmission Quality: The latency is lower than 28 ms.

810p/60fps Video Transmission Quality: The latency is lower than 40 ms.

With DJI Goggles 2:

1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.

1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.

Max Video Transmission Bitrate: 50 Mbps

Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)

Operating Temperature Range: -10º to 40º C (14° to 104° F)

Power Input: 7.4-26.4 V

Audio Transmission: N/A

END-TO-END LATENCY

With DJI FPV Goggles V2:

810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.

With DJI Goggles 2:

1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.


 Includes

1x Helion 10 6S HD

2x Battery pad

2x GEMFAN 1050 propellers(Pairs)

2x Battery strap

1xx Screw bag


iFlight BNF Helion 10 6S 10" HD Cinematic Long Range Quad w/DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz (GPS) from WREKD Co.

Introducing the iFlight Chimera 7" Long Range, Long Distance Drone! A super efficient iFlight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want! Super stiff frame for minimum resonance and 2806.5 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above. GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts included to cover you and your antenna dead ends just in case. GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (additional).Check out the entire Chimera7 Collection and all Replacement Parts!We also carry the Chimera4 LR collection! Check out all our Digital BNF/PNP/RTFs and our other iFlight Products! HIGHLIGHTS: - 6mm rigid arm design for more stiffness - Top- and bottom battery mount option - XING 2806.5 efficient wide stator motors - GPS pre-installed for more safety at distance - GoPro TPU bottom stand (GoPro protector not included) - 360° TPU protection, DJI cam protection and antenna mounts - DJI FPV Air Unit, buttery-smooth 720p\120fps FPV feed (TPU soft mounted) - No props in view (DJI Air unit record in 1080p/60fps) - Battery voltage LED status light (illuminated IF logo on the bottom) PRE-TUNED & PRE-SETUP: - Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience! To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps" - Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess! Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode" - GPS Rescue is OFF by default to prevent from unwanted or unexpected drone behaviour. Please check our linked article on "GPS Rescue Mode // Setup" FRAME // ：Chimera7 - Wheelbase: 320mm - Main body dimension: 258*199mm - Bottom to top distance: 20mm - Arm thickness: 6mm - Bottom plate thickness: 3mm - Top plate thickness: 2mm - Upper(middle) plate thickness: 3mm - Camera plate thickness: 3mm (included TPU inserts) ELECTRONICS // SucceX-D F7 V2.1 Stack (50A 4-in-1 ESC)： SucceX-D F7 V2.1 TwinG: - MCU: 216MHz STM32F722 - Gyro：2x ICM20689 - Baro: YES - Blackbox：32MB - Betaflight OSD: YES - BEC: 5V 2.5A / 9V 2.5A - Current sensor scale: 100 - Inverter for SBUS input (UART2-RX) - Smartaudio & Tramp VTX protocol supported - Beeper pad : Yes - RSSI input pad: No - UARTs：5 - Motor outputs: 8 - 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5) - 6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V) - BLHeli32 Telemetry：RX5 - Input voltage：recommended 2-6S, MAX 8S - Firmware Target: IFLIGHT_F722_TWING - Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm - Dimensions: 36*36mm - Weight: 7.5g - USB type-C ESC // SucceX 50A: - MCU: STM32F051 - Up tp 48kHz PWM frequency - Capacitance: 470uF/50V - Current Sensor: Yes - Input: 2-6S LIPO - Constant: 50A / Burst: 60A - BlHeli32 telemetry: Yes - BEC: No - Supports up to Dshot1200, Proshot, Oneshot, Multishot - Target: iFlight-BL32-4IN1 - Weight: 14.4g - Mounting pattern: 30.5*30.5mm/Φ3mm - Dimensions: 43*39mm (including the power pads) BNF // Parts list (Build): Prebuilt and indoor tested Quadcopter - 1x Chimera7 frame - 1x GoPro TPU bottom stand incl. lock screw - 1x DJI FPV camera - 1x DJI FPV Air Unit Module - 2x Albatross LHCP RP-SMA 5.8g 150mm antenna - 2 sets x Gemfan tri-blade 7040 props (Set of 4 - Color may vary) - 4x 20*250mm Microfiber PU Leather Battery Strap (Color May Vary)

IFlight Helion 10 6S HD 10 inch Long Range Drone W/ DJI O3 FPV System - Choose Receiver

GEPRC BNF CineLog 30 HD 3" Cinewhoop

Developed from the Cinelog25, the GEPRC CineLog30 is a dream of a pusher quad with incredibly stable HD video. It's perfect for carrying a Naked GoPro, SMO, or other actions cameras and is capable of freestyle or cinematic flight.  Built on the new ultra light and durable GEP-CL30 frame, it features more powerful 1404 

GEPRC BNF CineLog 30 HD 3

Developed by GEPRC, the CineLog30 is one of the best sub-250g FPV pusher drones in the current market! Analog and HD versions are available!

GEPRC CineLog 30 3" 4S HD CineWhoop Drone w/ Caddx Polar Vista 

GEPRC CineLog 30 3&quot 4S HD CineWhoop Drone w/ Caddx Polar Vista 

1.Newly Lightweight Design

The new design made the drone smaller and lighter. The most of important, CineLog30 can take off with 4s 660mah battery only 222.5 grams

2.Newly Noise Reduction Design
Unique noise reduction design can make CinLog30 noise much less than another Whoop Quadcopter

3.Carrying HD Digital VTX And Newly FPV Camera
Making video more clear and the perfect night vision images. Let you get a great flight experience.

4.Customized Mounting base
Perfectly suitable for naked camera GP8 and INSTA 360 GO2 camera

5.Upgrade Platform Design
Make the shooting and recording effect more stable

6.Backward Push Design
Bring higher flexibility, more stable freestyle flight experience and better shock absorption ability.

7.New personalized color matching
Show your difference

1.Newly Lightweight Design  The new design made the drone smaller and lighter. The most of important, CineLog30 can take off with 4s 660mah battery only 222.5 grams  2.Newly Noise Reduction Design Unique noise reduction design can make CinLog30 noise much less than another Whoop Quadcopter  3.Carrying HD Digital VTX And Newly FPV Camera Making video more clear and the perfect night vision images. Let you get a great flight experience.  4.Customized Mounting base Perfectly suitable for naked camera GP8 and INSTA 360 GO2 camera  5.Upgrade Platform Design Make the shooting and recording effect more stable  6.Backward Push Design Bring higher flexibility, more stable freestyle flight experience and better shock absorption ability.  7.New personalized color matching Show your difference

GEPRC CineLog30 HD w/ Runcam Link Wasp Digital HD System - GEPRC

GEPRC CineLog30 HD w/ Runcam Link Wasp Digital HD System

GEPRC BNF CineLog 35 Performance Analog 3.5" Quadcopter

The CineLog35 Performance version is now released in two versions: Runcam Link Wasp and Analog version. There are also 3 receiver options. The CineLog35 Performance version is optimized and upgraded based on the standard version. The CineLog35 is designed with lighter weight and longer endurance. The concept of the Per

GEPRC CineLog35 Performance Edition 3.5

The CineLog35 Performance version RTF is optimized and upgraded based on the standard version. The CineLog35 is designed with lighter weight and longer endurance, and the concept of the Performance version is to maximize Racing performance and achieve perfection with the existing frame size.

The CineLog35 Performance version RTF is optimized and upgraded based on the standard version. The CineLog35 is designed with lighter weight and longer endurance, and the concept of the Performance version is to maximize Racing performance and achiev

GEPRC CineLog 35 P 3.5" Cinewhoop Drone Analog w/ Caddx Ratel 2 - Performance Edition - 6S 

GEPRC CineLog 35 P 3.5&quot Cinewhoop Drone Analog w/ Caddx Ratel 2 - Performance Edition - 6S 

Recommended GEPRC 6S 1550mAh Li-HV Battery for CineLog35 Performance

GEPRC CineLog35 Performance Analog FPV Drone - GEPRC

GEPRC CineLog35 Performance Analog FPV Drone

The CineLog35 Performance version is now released in three versions: VISTA Nebula PRO,AVATAR HD 1080P and Analog version. There are also 4 receiver options. The CineLog35 Performance version is optimized and upgraded based on the standard version. The CineLog35 is designed with lighter weight and longer endurance. The 

SpeedyBee

SpeedyBee PNP Flex25 Analog Cinewhoop

 Check out all our Analog BNF/PNP/RTF Drones and the rest of our SpeedyBee Products!  Don't forget to get the LED Lighting Kit to add some bling to your drone! Specifications: Wheelbase: 78mm Flight Controller &amp; ESC SpeedyBee: F745 35A AIO Gyro: MPU6000 OSD Chip: AT7456E VTX SpeedyBee: TX800 Camera: RunCam Phoenix 

SpeedyBee Flex25 Analog 2.5

SpeedyBee PNP Flex25 HD Falcon/Runcam Link Cinewhoop

 Check out all our Digital BNF/PNP/RTF Drones and the rest of our SpeedyBee Products!  Don't forget to get the LED Lighting Kit to add some bling to your drone! Specifications: Wheelbase: 78mm Flight Controller &amp; ESC SpeedyBee: F745 35A AIO Gyro: MPU6000 OSD Chip: AT7456E VTX &amp; Camera: RunCam Falcon 120fps Digi

SpeedyBee Flex25 HD 2.5

GEPRC BNF GEP-MK5 Mark5 HD 5" Quadcopter

Recommend GEPRC Storm 1550mAh Battery for MARK5 4S Version
Recommend GEPRC Storm 1400mAh Battery for MARK5 6S Version
Note: From August 18, 2023, any purchase of a 5-inch drone will receive a free pack of 5040 propellers in random colors.

Recommend GEPRC Storm 1550mAh Battery for MARK5 4S Version Recommend GEPRC Storm 1400mAh Battery for MARK5 6S Version Note: From August 18, 2023, any purchase of a 5-inch drone will receive a free pack of 5040 propellers in random colors.

GEPRC MARK5 HD DJI AIR UNIT Freestyle FPV Drone - GEPRC

GEPRC MARK5 HD DJI AIR UNIT Freestyle FPV Drone

Pre-Orders shipping ASAP!
The GEPRC BNF Mark5 HD Quad w/ Caddx Air Unit Micro is developed specifically for freestyle with squashed X arm design. Unique shock absorbing structure design, less vibrations and resonance, to provide a stable operating environment for the electronic system. Aluminum alloy side plates not only look stunning, but also reduce weight and add more endurance. 
Make sure to check the ELRS Version!
Gopro case available separately.
Check out all our pre-built quads, and all our GEPRC selection!



Specifications

Input Voltage: 6S

Wheelbase: 225mm
Top plate: 2.5mm
Bottom plate: 2.5mm
Arm: 5mm
Charge connector: XT60
Motor: 2107.5 1960Kv

Weight: 385.5g

SPAN F722-HD-BT FC

MCU: STM32F722
IMU: MPU6000(SPI)
OSD: BetaFlight OSD w/AT7456E chip
Blackbox: 16Mb Flash
BEC: 5V, 9V

LC Filter: Yes

G50A ESC

MCU: STM32F051K86
Max Continuous Current: 50A
Max Burst Current: 55A
BEC: No
Current Sensor: Yes

Caddx Air Unit

Operating Temperature: 32 to 104 F (0 to 40 C)Input Power: 7.4-17.6V
Transmitter Power: FCC/SRRC: &lt30dBm CE: &lt14dBm
I/O Interface: USB-C, MMCX, 3-in1 Port, MicroSD
Output Power: 25mW3200mW/500mW/700mW
Video Transmission: 28ms Low Latency
Dimensions:

Air Unit: 44x37.8x14.4mm
Camera:20.7x19x19mm

Flight Control System: BetaFlight
Max Transmission Range: 4km
Coaxial Cable Length: 100mm
FOV: 150(D) 122(H) 93(V)
Goggle Compatibility: DJI
Closed Loop 4-in-1: Yes
Frequency Channels: 8
Shutter: Rolling Shutter
Sensor: 1/3.2" CMOS
Effective Pixels: 4 M
Image: 720p/120fps
Video Format: MP4
Video: 1080p/60fps
Lens: 2.1mm, F/21
ISO: 100-256000

Includes

1x GepRC BNF Mk5 Quad
4x Freestyle 4S propellers (pair)
1x Battery strap M15x250mm
2x Battery strap M20x220mm
2x Battery Silicone Pads
1x Camera cage carbon top plate
1x 3D print mountings combination
2x Action camera mount holder
1x Set of screws
1x Set of screwdrivers
1x Antenna fixed tube


Pre-Orders shipping ASAP! The GEPRC BNF Mark5 HD Quad w/ Caddx Air Unit Micro is developed specifically for freestyle with squashed X arm design. Unique shock absorbing structure design, less vibrations and resonance, to provide a stable operating environment for the electronic system. Aluminum alloy side plates not on

(PRE-ORDER) GEPRC BNF Mark5 HD 6S 5" Quad w/ Caddx Air Unit Micro - Choose Version

(PRE-ORDER) GEPRC BNF Mark5 HD 6S 5" Quad w/ Caddx Air Unit Micro - Ch

The GEPRC BNF Mark5 HD Quad w/ DJI Camera is developed specifically for freestyle with squashed X arm design. Unique shock absorbing structure design, less vibrations and resonance, to provide a stable operating environment for the electronic system. Aluminum alloy side plates not only look stunning, but also reduce we

GEPRC BNF Mark5 HD 5

Pre-Orders shipping ASAP!
The GEPRC BNF Mark5 HD Quad w/ Caddx Air Unit Micro is developed specifically for freestyle with squashed X arm design. Unique shock absorbing structure design, less vibrations and resonance, to provide a stable operating environment for the electronic system. Aluminum alloy side plates not only look stunning, but also reduce weight and add more endurance. 
Make sure to check the ELRS Version!
Gopro case available separately.
Check out all our pre-built quads, and all our GEPRC selection!



Specifications

Input Voltage: 6S

Wheelbase: 225mm
Top plate: 2.5mm
Bottom plate: 2.5mm
Arm: 5mm
Charge connector: XT60
Motor: 2107.5 1960Kv

Weight: 385.5g

SPAN F722-HD-BT FC

MCU: STM32F722
IMU: MPU6000(SPI)
OSD: BetaFlight OSD w/AT7456E chip
Blackbox: 16Mb Flash
BEC: 5V, 9V

LC Filter: Yes

G50A ESC

MCU: STM32F051K86
Max Continuous Current: 50A
Max Burst Current: 55A
BEC: No
Current Sensor: Yes

Caddx Air Unit

Operating Temperature: 32 to 104 F (0 to 40 C)Input Power: 7.4-17.6V
Transmitter Power: FCC/SRRC: &amplt30dBm CE: &amplt14dBm
I/O Interface: USB-C, MMCX, 3-in1 Port, MicroSD
Output Power: 25mW3200mW/500mW/700mW
Video Transmission: 28ms Low Latency
Dimensions:

Air Unit: 44x37.8x14.4mm
Camera:20.7x19x19mm

Flight Control System: BetaFlight
Max Transmission Range: 4km
Coaxial Cable Length: 100mm
FOV: 150(D) 122(H) 93(V)
Goggle Compatibility: DJI
Closed Loop 4-in-1: Yes
Frequency Channels: 8
Shutter: Rolling Shutter
Sensor: 1/3.2&quot CMOS
Effective Pixels: 4 M
Image: 720p/120fps
Video Format: MP4
Video: 1080p/60fps
Lens: 2.1mm, F/21
ISO: 100-256000

Includes

1x GepRC BNF Mk5 Quad
4x Freestyle 4S propellers (pair)
1x Battery strap M15x250mm
2x Battery strap M20x220mm
2x Battery Silicone Pads
1x Camera cage carbon top plate
1x 3D print mountings combination
2x Action camera mount holder
1x Set of screws
1x Set of screwdrivers
1x Antenna fixed tube


GEPRC BNF Mark5 HD 6S 5" Quad w/ Caddx Air Unit Micro - Choose Version from WREKD Co.

GEPRC BNF Mark5 HD 6S 5

iFlight BNF ProTek60 Pro HD Cinelifter

The Protek60 Pro is a cinelifter drone designed to carry cinematic cameras such as Komodo, Zcam, BMPCC, or even a GH5.

iFlight Protek60 Pro HD BNF 6S Cinelifter - BMPCC, Universal Version

Let's introduce our latest member to our ProTek family, the all-new iFlight ProTek60 Cinelifter! We've came a long way with action cameras, offering outstanding quality with little weight and a small footprint. But do you want to get professional or shoot some commercials, maybe get into cinema videography? Well, then 

iFlight ProTek60 Pro HD 6S Cinelifter w/ DJI Air Unit - Choose Version

iFlight Protek60 Pro HD BNF 6S Cinelifter - ZCAM, RED Version

BetaFPV

BetaFPV BNF Pavo30 3" Cinewhoop

BETAFPV

Pavo30 whoop quadcopter, a new concept of a 3-inch pusher drone developed by BETAFPV, is going further in performance, durability, and power with a brand new powerful propulsion system. It's powerful enough to carry SMO 4K camera or a customized Naked Camera for all FPV freestyle tricks, and also can carry a GoPro for some simple action flying. Hence this 3-inch whoop drone can meet more high-quality shooting needs. Pilots can enjoy an incredibly stable and clear HD footage video while on the FPV flight!
Note: Back in stock now! Now Pavo30 Whoop Quadcopter Analog VTX version adopts A03 5.8G VTX instead of M02 5.8G VTX. Both VTX features similar performance for FPV transmission.

Bullet Point

Pavo30 is the first 3-inch pusher whoop drone developed by BETAFPV. Compared with the Beta95X V3 pusher whoop drone, it's going further in performance and durability with a brand new powerful propulsion system.
Both analog and HD Digital VTX versions come with Toothpick F722 AIO 35A FC, 1506-3000KV motor &amp Gemfan D76 5-Blades props, this highly efficient powerful propulsion system lays the foundation for powerful and stable flight. 
Pavo30 whoop drone can do both freestyle and cinematic shot both. Not only can support carrying SMO 4K camera or a customized Naked Camera for more maneuverable to achieve all FPV freestyle tricks, but it can also carry a GoPro for some simple action flying.
Equipped with a newly developed Pavo30 frame, which is made of PA12 material, it has higher abrasion resistance, toughness, and shows excellent impact resistance in drop &amp impact tests.
Centering the drone's gravity by reversed-motor design and more compact structure to make the drone more maneuverable to achieve all FPV freestyle.
The shock mitigation system with cushion makes cameras more stable on the flight, which ensures pilots can capture all the beautiful moments of flight with the stabilized and clear video.
Pavo30 whoop drone (HD Digital VTX) comes with Nebula micro HD camera and Vista VTX system. The drone can support the DJI FPV Goggles. Pilots can enjoy superb FPV pictures and long transmission distances.


Specification




Pavo30 Whoop Drone(Analog VTX)
Pavo30 Whoop Drone(HD Digital VTX)




Weight


145g (without battery)
173g (without battery)




Wheelbase


118mm
118mm




FC



F722 AIO 35A FC (MPU6000)
F722 AIO 35A FC (MPU6000)




Frame


Pavo30 Frame Kit
Pavo30 Frame Kit




Motor


1506- 3000KV motor
 1506- 3000KV motor




Propeller


Gemfan D76 5-Blade props with 5/1.5mm shaft hole
 Gemfan D76 5-Blade props with 5/1.5mm shaft hole 




Receiver Option


Frsky FCC/Frsky LBT/TBS/FUTABA/PNP 
Frsky FCC/Frsky LBT/TBS/PNP




FPV Camera


ANT Nano camera
Nebula Nano camera




FPV Camera Tilt Degree



0°- 60° 


0°- 60° 





VTX


A03 400mW 5.8G
VISTA HD Digital VTX




Camera Mount


SMO 4K camera Mount
SMO 4K camera Mount




SMO 4K Tilt Degree


5°- 45° 

5°- 45° 





Battery



750mAh 4S battery /850mAh 4S battery (Not included) 

750mAh 4S battery /850mAh 4S battery (Not included) 





Charge Connector


XT30
XT30




Flight time


About 6-8 minutes
About 6-8 minutes






BETAFPV SMO 4K Camera
SMO 4K camera, a high-degree lightweight action camera for FPV drones that are developed by BETAFPV using Insta360 technology. SMO 4K camera only weighs 30g and is perfectly fit for FPV drones, and brings pilots an extraordinary flying experience and a strong visual impact. It will be the perfect action camera for pilots in search of high-quality video with FPV racing drones. In addition to SMO 4k, the Pavo30 whoop drone also supports carrying a customized Naked Camera and a whole GoPro.
Comes with input power connector for SMO 4K camera in default (Pre-soldered)
Pavo30 Frame Kit
Equipped with a newly developed Pavo30 frame made of PA12 material, it has higher abrasion resistance, toughness, and shows excellent impact resistance in drop &amp impact tests. So the whole drone will be a more durable flight and no fear of a crash. The reversed pusher style puts all the cameras and batteries on the top of the drone, coupled with a more compact frame structure, the center of gravity of Pavo30 is right in the middle, which makes the flight more flexible. 

Analog Camera &amp VTX
Pavo30 whoop drone analog VTX version comes with Caddx ant camera, which is an analog FPV micro camera with 1200TVL Global WDR, only weight 2g.  In addition, A03 400mW OpenVTx video transmitter which supports SmartAudio&ampTramp protocol with PIT/RCE/100/400mW adjustable output power. Therefore, pilots can customize the output power and frequency to explore more possibilities and have fun.

Nebula Micro HD System
Pavo30 whoop Drone HD Digital VTX version comes with Caddx Digital HD Camera Nebula Nano, which can perfectly support DJI goggles. With DJI goggles, it can provide 720p/60fps digital high-definition picture and a transmission range up to 4km. Users can choose 25mW/200mW/500mW/700mW from DJI goggle settings. It is smaller and designed for whoop drones. 

FC &amp ESC
Equipped with the updated F722 2-6S 35A AIO FC(BLHeli_S), the Pavo30 whoop drone totally supports a 4S battery for a stable and flexible flight experience. Come with a BETAFPVF722 processor FC, BetaFlight OSD, and 35A BLHeli_S ESC, this AIO flight controller offers more powerful flight performance that can push your FPV racer to the max. We highly recommend a 750mAh 4S battery for the drone, Pavo30 can get 6-8min flight time with it.

Motor &amp Props
Pavo30 analog VTX and HD Digital VTX version come with 1506-3000KV motor &amp Gemfan D76 5-Blades props, these 2 configurations achieve a perfect dynamic balance, which gives the drone more flexible and longer flying time. Pilots can enjoy powerful and stable flights with less noise.

The Pavo30 Whoop Quadcopter also comes with "props out" by default. Why do we need "props out" direction?
Default Betaflight props direction, quadcopter dips, and "washes out" in hard corners. With reversed props or "props out", no more dipping even in the hardest cornering.
Know more about "Props Out".

FAQ
1. Cli Dump of Pavo30 Whoop Quadcopter(Click here to find the details).
2. Cli Dump of Pavo30 Whoop Quadcopter(HD Digital VTX) (Click here to find the details).
3. STL File for the Base of Naked Camera for Pavo30 Pusher Drone Series (Click here to find the details.)
4. How to power the Naked Camera on Pavo30 or Pavo30 HD Digital VTX.
One adapter 3-pin GH1.25 power cable for Customized Naked Camera is offered in the package, pilots can use it to power the Naked Camera.
5. How to Connect the External Rx to Toothpick F722 35A AIO FC (Click here to find the details).




Package

1 * Pavo30 Whoop Quadcopter (HD Digital VTX or Analog VTX)
1 * Gemfan D76 5-Blade props(2CW+2CCW)
1 * 20mm FPV Camera Mount
1 * USB Adapter Board for FC
1 * Adapter Cable for Customized Naked Camera

Now Pavo30 Whoop Quadcopter Analog VTX version adopts A03 5.8G VTX instead of M02 5.8G VTX. Both VTX features similar performance for FPV transmission.


Batteries and SMO 4K Camera are not included in the package. You can get it here for 750mAh 4S battery/ 850mAh 4S battery and SMO 4K camera.




Pavo30 whoop quadcopter, a new concept of a 3-inch pusher drone developed by BETAFPV, is going further in performance, durability, and power with a brand new powerful propulsion system. It's powerful enough to carry SMO 4K camera or a customized Naked Camera for all FPV freestyle tricks, and also can carry a GoPro for 

Pavo30 Whoop Quadcopter

Pavo30 whoop quadcopter, a new concept of 3-inch pusher drone developed by BETAFPV, is going further in performance, durability and power with brand new power system. It's powerful enough to carry SMO 4K camera or a customized Naked Camera for all FPV freestyle tricks, and also can carry a GoPro for some simple action 

BetaFPV Pavo30 3

The Pavo30 Whoop Quadcopter is a 3-inch pusher drone developed by BETAFPV. The Pavo30 is powerful enough to carry an SMO 4K camera, a customized Naked camera for all FPV freestyle tricks, and a GoPro for some simple action flying!  This 3-inch whoop drone can meet high-quality shooting needs! Pilots can enjoy an incred

The Pavo30 Whoop Quadcopter is a 3-inch pusher drone developed by BETAFPV. 

BETAFPV Pavo30 3" CineWhoop Drone (Analog)

BETAFPV Pavo30 3&quot CineWhoop Drone (Analog)

GEPRC BNF CineLog 30 Analog 3" Cinewhoop

Developed from the Cinelog25, the GEPRC CineLog30 is a dream of a pusher quad. It's perfect for carrying a Naked GoPro, SMO, or other actions cameras and is capable of freestyle or cinematic flight.  Built on the new ultra-light and durable GEP-CL30 frame, it features more powerful 1404 3850Kv motors and T3x3x3 propell

GEPRC BNF CineLog 30 3

GEPRC CineLog 30 3" 4S Analog CineWhoop Drone

GEPRC CineLog 30 3&quot 4S Analog CineWhoop Drone

1.Newly Lightweight Design

The new design made the drone smaller and lighter. The most of important, CineLog30 can take off with 4s 660mah battery only 222.5 grams

2.Newly Noise Reduction Design
Unique noise reduction design can make CinLog30 noise much less than another Whoop Quadcopter

3.Customized Mounting base
Perfectly suitable for naked camera GP8 and INSTA 360 GO2 camera

4.Upgrade Platform Design
Make the shooting and recording effect more stable

5.Backward Push Design
Bring higher flexibility, more stable freestyle flight experience and better shock absorption ability.

6.New personalized color matching
Show your difference

1.Newly Lightweight Design  The new design made the drone smaller and lighter. The most of important, CineLog30 can take off with 4s 660mah battery only 222.5 grams  2.Newly Noise Reduction Design Unique noise reduction design can make CinLog30 noise much less than another Whoop Quadcopter  3.Customized Mounting base Perfectly suitable for naked camera GP8 and INSTA 360 GO2 camera  4.Upgrade Platform Design Make the shooting and recording effect more stable  5.Backward Push Design Bring higher flexibility, more stable freestyle flight experience and better shock absorption ability.  6.New personalized color matching Show your difference

GEPRC CineLog30 w/ Analog Caddx Ratel2 - GEPRC

GEPRC CineLog30 w/ Analog Caddx Ratel2

iFlight BNF Alpha A85 HD Whoop

The A85 Whoop w/Caddx Loris 4K features the SucceX-D 20A Whoop F4 AIO Board and XING NANO 1303 5000KV Motors, and records 4k HD footage all in a super lightweight and power whoop!

iFlight Alpha A85 Whoop - HD w/ Caddx Loris 4K

Ever wanted to try Digital FPV on the smallest possible whoop size quad? iFlight put the Caddx Vista and the new Caddx Nebula cam on one of our new 2inch whoop frames, then did some tuning and tried to find the optimal ratio between weight and power, to get the perfect balance between flight time, efficiency, and power

iFlight Alpha A85 w/Caddx Polar Nano Digital HD System

NewBeeDrone

NewBeeDrone BNF AcroBee75 BLV4 HD 75mm Whoop - DJI O3, 2.4GHz ELRS





NewBeeDrone AcroBee75 HD O3
Introducing the AcroBee75 HD O3 BNF - a compact powerhouse. It's the pioneer whoop featuring G4 flight controller and built-in ELRS2.4 receiver, effortlessly compatible with Dshot600 and bi-directional Dshot. As the tiniest and lightest HD whoop with a complete DJI O3 unit available, it boasts remarkable agility and an impressive flight time of nearly 3.5 minutes. Our expert tuning ensures seamless indoor filming in self-level and acro modes. To optimize performance and visuals, turn on DJI RockSteady via goggle settings. Note that this model is not suitable for outdoor or windy conditions.

 




Explore and film spaces you never could before in HD! A must-have tool for professionals and hobbyists specializing in indoor space.
 


Compared to other O3 HD whoops at 85mm and 80mm, NewBeeDrone engineered DJI O3 into a 75mm frame. This is the new standard for the smallest O3 HD whoop. 
 


The only HD Micro whoop board with G4 processor. Dual-bearing motors allow less friction in spinning while 3-blade Azi propellors were developed with engineering theory for optimal air-grab and stability. We master-tuned this drone to have the smoovest flight and absolutely no jello in any videos. 
 



We found the best ratio between the size of drone and its weight distribution. Without DJI O3, the drone can fly up to 8 minutes. Up to 3 minutes with DJI O3 and battery. Choose between 3D printed battery mounts or strap.  
 



We ensure that you get the best material and components  that are available so you can rely on the drone without troubleshooting or breaking. All parts are available separately as replacements. Additional flexibility with SLS Nylon prints allow cameras to be changed or updated if needed. 
 



Assembly or tuning not required. Save time and energy so you can focus on your footage. Drone comes with built-in ExpressLRS and ready to pair. Built-in blackbox records data for tuning. Configure to DJI PNP on Betaflight if needed. Don't be afraid of messing up on customization. Reset to factory default (with our tunes and dump files) in one click if something is not right.
 





Our support team in the United States are here to help. US customers enjoy Unlimited Frame Warranty from our site. For other countries, please ask your local store to see if they offer replacement. 
 

Specifications:
Drone Size: 75mmFlight Controller: BeeBrain HD G4 Flight Controller ExpressLRS (ELRS) 2.4GFrame: Cockroach75 Brushless FrameMotors: Flow 0804 12000kv Double Ball Bearing Brushless MotorPropellesr: Azi (Tri-Blade) Micro Propellers 40mm - 1.0mm ShaftHD VTX &amp Camera: DJI O3 Air UnitCanopy: NewBeeDrone Acrobee75 HD O3 CanopyTotal Weight without battery: 70.19gTotal Weight with battery: 98.24g - 99g
Recommended battery: Tattu 450mAh 7.6V High Voltage 95C 2S1P Lipo Battery Pack with XT30 Plug - Long PackTattu R-Line 550mAh 7.4V 95C 2S1P Lipo Battery Pack with XT30 PlugBeeBrain BLV4 HD G4 Flight Controller ELRS2.4G Specifications:

MCU: STM32G474
ESC Firmware: Z-H-40 - Bluejay 0.19.2 48kHz.
ESC Specifications: 1 channel 20A ESC
Receiver: NBD ExpressLRS 3.0 Diversity (non-SPl)
Receiver Antenna: 1x BeeT-Antenna 1x 2.4G receiver antenna
Flight Controller Weight:7.4g (including antenna and XT30 Battery connector)
Flight Controller Size: Outer dimensions :29 x 29 x 7.6 mm
Flight Controller Holes: 25.5 x 25.5 mm
Battery Input: 1-2S
BEC:10V 2A for DJI O3 (under 2S power only)
BEC：5V 2A
UART1: Free
UART2: TX &amp RX for EXPRESSLRS 3.0 receiver
UART3: Free
UART4: Free
Flight time with Tattu 450mAh 2S battery is 3:00min (at 7v) 

 Firmware: 
BeeBrain BLV4 HD Betaflight 4.4.0 firmware with tune
All new Firmware can be found on NewBeeDrone Github page

 
What’s included: 
1x NewBeeDrone AcroBee75 HD DJI O3 BNF2x Extra HD Canopies1x Extra Battery Strap (for other sized batteries) 4x Azi 40mm PropellersWarning: This drone has been carefully crafted using only newbeedrone parts. It is important to note that any use of non-compatible parts from other brands may result in technical difficulties. Additionally, should you choose to modify the drone, it is crucial that you assume full responsibility for any resulting issues. It is not advisable to proceed with modifications without the necessary knowledge and expertise. We appreciate your understanding and cooperation in ensuring the safe operation of the drone.*Note: For outdoor flying, RockSteady is required in order to get the best picture quality(On DJI goggle Menu). The PID tune are base on the current setup. If you change any setting on the drone and it is acting weird, please flash the newest firmware

Video:

Review Video:

NewBeeDrone AcroBee75 HD O3 Introducing the AcroBee75 HD O3 BNF - a compact powerhouse. It's the pioneer whoop featuring G4 flight controller and built-in ELRS2.4 receiver, effortlessly compatible with Dshot600 and bi-directional Dshot. As the tiniest and lightest HD whoop with a complete DJI O3 unit available, it boas

NewBeeDrone BNF AcroBee75 HD O3 Whoop - Choose Receiver


NewBeeDrone AcroBee75 HD O3 Kit Only (No DJI O3 Air Unit)
Introducing the AcroBee75 HD O3 Kit - a compact powerhouse. It's the pioneer whoop featuring  G4 flight controller with upgraded Double N-MOS and MPU6000 Gyro with built-in ELRS2.4 receiver, effortlessly compatible with Dshot600 and bi-directional Dshot. As the tiniest and lightest HD whoop to compatible with DJI O3 unit, it boasts remarkable agility and an impressive flight time of nearly 3.5 minutes. Our expert tuning ensures seamless indoor filming in self-level and acro modes. To optimize performance and visuals, turn on DJI RockSteady via goggle settings. Note that this model is not suitable for outdoor or windy conditions. Plug and Ply with DJI O3 Air Unit. 
DJI O3 installation instruction: 1. Replace O3 antenna to the BeeTX 5.8Ghz Antenna2. Unscrew the Acrobee75 HD O3 Canopy3. Insert the camera(make sure the DJI logo on the back of the camera are point up)4. Insert the antenna into the canopy first then insert the O3 Air Unit5. Insert the cable through the gap between the air unit and the canopy, plug in the cable.6. Install back the canopy and tight up the camera. 






Explore and film spaces you never could before in HD! A must-have tool for professionals and hobbyists specializing in indoor space.
 


Compared to other O3 HD whoops at 85mm and 80mm, NewBeeDrone engineered DJI O3 into a 75mm frame. This is the new standard for the smallest O3 HD whoop. 
 


The only HD Micro whoop board with G4 processor. Dual-bearing motors allow less friction in spinning while 3-blade Azi propellors were developed with engineering theory for optimal air-grab and stability. We master-tuned this drone to have the smoovest flight and absolutely no jello in any videos. 
 



We found the best ratio between the size of drone and its weight distribution. Without DJI O3, the drone can fly up to 8 minutes. Up to 3 minutes with DJI O3 and battery. Choose between 3D printed battery mounts or strap.  
 



We ensure that you get the best material and components  that are available so you can rely on the drone without troubleshooting or breaking. All parts are available separately as replacements. Additional flexibility with SLS Nylon prints allow cameras to be changed or updated if needed. 
 



Assembly or tuning not required. Save time and energy so you can focus on your footage. Drone comes with built-in ExpressLRS and ready to pair. Built-in blackbox records data for tuning. Configure to DJI PNP on Betaflight if needed. Don't be afraid of messing up on customization. Reset to factory default (with our tunes and dump files) in one click if something is not right.
 









Our support team in the United States are here to help. US customers enjoy Unlimited Frame Warranty from our site. For other countries, please ask your local store to see if they offer replacement. 
 

Specifications:
Drone Size: 75mmFlight Controller: BeeBrain HD G4 Flight Controller ExpressLRS (ELRS) 2.4GFrame: Cockroach75 Brushless FrameMotors: Flow 0804 12000kv Double Ball Bearing Brushless MotorPropellesr: Azi (Tri-Blade) Micro Propellers 40mm - 1.0mm ShaftHD VTX &amp Camera: DJI O3 Air UnitCanopy: NewBeeDrone Acrobee75 HD O3 CanopyTotal Weight without battery: 70.19gTotal Weight with battery: 98.24g - 99g
Recommended battery: Tattu 450mAh 7.6V High Voltage 95C 2S1P Lipo Battery Pack with XT30 Plug - Long PackTattu R-Line 550mAh 7.4V 95C 2S1P Lipo Battery Pack with XT30 PlugBeeBrain BLV4 HD G4 Flight Controller ELRS2.4G Specifications:

MCU: STM32G474
ESC Firmware: Z-H-40 - Bluejay 0.19.2 48kHz.
ESC Specifications: 1 channel 20A ESC
Receiver: NBD ExpressLRS 3.0 Diversity (non-SPl)
Receiver Antenna: 1x BeeT-Antenna 1x 2.4G receiver antenna
Flight Controller Weight:7.4g (including antenna and XT30 Battery connector)
Flight Controller Size: Outer dimensions :29 x 29 x 7.6 mm
Flight Controller Holes: 25.5 x 25.5 mm
Battery Input: 1-2S
BEC:10V 2A for DJI O3 (under 2S power only)
BEC：5V 2A
UART1: Free
UART2: TX &amp RX for EXPRESSLRS 3.0 receiver
UART3: Free
UART4: Free
Flight time with Tattu 450mAh 2S battery is 3:00min (at 7v) 

 Firmware: 
BeeBrain BLV4 HD Betaflight 4.4.0 firmware with tune
All new Firmware can be found on NewBeeDrone Github page
What’s included: 
1x NewBeeDrone AcroBee75 HD O3 Without O3 Kit3x Acrobee75 HD O3 Canopy1x Extra Battery Strap (for other sized batteries)4x Azi 40mm PropellersWarning: This drone has been carefully crafted using only newbeedrone parts. It is important to note that any use of non-compatible parts from other brands may result in technical difficulties. Additionally, should you choose to modify the drone, it is crucial that you assume full responsibility for any resulting issues. It is not advisable to proceed with modifications without the necessary knowledge and expertise. We appreciate your understanding and cooperation in ensuring the safe operation of the drone.*Note: For outdoor flying, RockSteady is required in order to get the best picture quality(On DJI goggle Menu). The PID tune are base on the current setup. If you change any setting on the drone and it is acting weird, please flash the newest firmware

Video:

Review Video:

NewBeeDrone AcroBee75 HD O3 Kit Only (No DJI O3 Air Unit) Introducing the AcroBee75 HD O3 Kit - a compact powerhouse. It's the pioneer whoop featuring  G4 flight controller with upgraded Double N-MOS and MPU6000 Gyro with built-in ELRS2.4 receiver, effortlessly compatible with Dshot600 and bi-directional Dshot. As the 

NewBeeDrone BNF AcroBee75 HD O3 Kit Only

Introducing the smallest HD whoop with the DJI O3 currently on the market. This amazing 75mm quadcopter comes with the elite DJI O3 Air Unit and O3 Micro Cam, and the new BeeBrain BLV4 HD F7 AIO flight controller. Achieve sharper HD capture with amazing quality with O3 Air Unit. Boasting powerful 0804 12000kv dual ball bearings motors, despite its small size, this thing will rip! 
Check out our other pre-built quads, as well as the rest of our NewBeeDrone selection.






Explore and film spaces you never could before in HD! A must-have tool for professionals and hobbyists specializing in indoor space.





The only HD Micro whoop board with F7 processor. Dual-bearing motors allow less friction in spinning while 3-blade Azi propellors were developed with engineering theory for optimal air-grab and stability. We master-tuned this drone to have the smoovest flight and absolutely no jello in any videos. 

We found the best ratio between the size of drone and its weight distribution. Without DJI O3, the drone can fly up to 8 minutes. Up to 3 minutes with DJI O3 and battery. Choose between 3D printed battery mounts or strap.  

We ensure that you get the best material and components  that are available so you can rely on the drone without troubleshooting or breaking. All parts are available separately as replacements. Additional flexibility with SLS Nylon prints allow cameras to be changed or updated if needed. 

Assembly or tuning not required. Save time and energy so you can focus on your footage. Drone comes with built-in ExpressLRS and ready to pair. Built-in blackbox records data for tuning. Configure to DJI PNP on Betaflight if needed. Don&#39t be afraid of messing up on customization. Reset to factory default (with our tunes and dump files) in one click if something is not right.






Specifications 


Drone Size: 75mm

Flight Controller: BeeBrain BLV4 HD F7 Flight Controller ExpressLRS (ELRS) 2.4G

Frame: Cockroach75 Brushless Frame

Motors: Flow 0804 12000kv Double Ball Bearing Brushless Motor

Propellesr: Azi (Tri-Blade) Micro Propellers 40mm - 1.0mm Shaft

HD VTX &ampamp Camera: DJI O3 Air Unit

Canopy: NewBeeDrone Acrobee75 HD O3 Canopy

Total Weight without battery: 70.19g

Total Weight with battery: 98.24g

BeeBrain BLV4 HD F7 Flight Controller ELRS2.4G Specifications:

MCU: STM32F745
ESC Firmware: S-H-40 - Bluejay, 0.19.2, 48kHz.
ESC Specifications: 4 channel 12A ESC

ESC Connector: JST-1.0 3Pin
Weight: 6.6 grams (including antennas and battery connector)
Size: Outer dimensions 29 x 29 x 7.6 mm
Holes: 25.5 x 25.5 mm
Battery input: 2S
Connector: XT30
Internal Blackbox: 16MB
Gyro: BMI270
UART1: SBUS on DJI Connector (RX only)
UART2: TX &ampamp RX for internal ExpressLRS 3.0 receiver
UART3: TX &ampamp RX for DJI MSP+Displayport

Flight time with Tattu 450mAh 2S battery is 3:00min (at 7v) 

Firmware: 

BeeBrain BLV4 HD Betaflight 4.4.0 firmware with tune

Includes

1x NewBeeDrone BNF AcroBee75 BLV4 2S HD 75mm w/ DJI O3 Air Unit &ampamp Micro Cam - ELRS 2.4GHz


Introducing the smallest HD whoop with the DJI O3 currently on the market. This amazing 75mm quadcopter comes with the elite DJI O3 Air Unit and O3 Micro Cam, and the new BeeBrain BLV4 HD F7 AIO flight controller. Achieve sharper HD capture with amazing quality with O3 Air Unit. Boasting powerful 0804 12000kv dual ball

NewBeeDrone BNF AcroBee75 BLV4 2S HD 75mm Whoop w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz from WREKD Co.

NewBeeDrone BNF AcroBee75 BLV4 2S HD 75mm Whoop w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz

NewBeeDrone BNF CinemAh 3" Cinewhoop



NewBeeDrone CinemAh BNF 4S DJI HD with Crossfire Receiver

A New Cinewhoop Design Philosophy

To date, many ducted cinewhoop frames have been needlessly heavy. Additionally, existing light cinewhoop frames don’t have guarded props for flying around softer targets. Heavy frames leave you with very little room for adaptability to use the frame for your shoots whether it be increased payload capacity or the option for larger batteries. We at NewBeeDrone worked to change that.
The CinemAh Frame - The Most Versatile Cinewhoop Frame
The CinemAh frame is NewBeeDrone’s response to the need for a lighter and more versatile cinewhoop frame to carry a full GoPro. The CinemAh has a unique all-carbon fiber frame structure that allows for easy access to electronics while providing maximum structural strength.
The GoPro Mount (Not Included)
The NewBeeDrone CinemAh cinewhoop TPU GoPro 8 and 9 mounts allow for 4 built-in angles for quick-snap adjustment from 0 deg to 22.5 deg. The capture cam mounts are 2xM2 mounting holes set 20mm apart allowing the community to design any mounting solution for any HD capture cam option. 
Other 3D Printed Accessories (Not Included)
﻿Check out our complete collection of 3D printed accessories for the Cinemah! We've got snap in ducts, lightweight battery straps, and protective duct coverings in addition to action camera mounts.
 
Electronics Mounting:

2 sets of 1x1inch mounting locations
Front 20x20 location has M3 mounting for a flight controller and ESC stack.
Rear 20x20 location has M2 mounting for Caddx Vista – with rear antenna mount.
Camera mounting – single and double screw camera mounting options.
Note: The frame does not fit an air unit.

Motor Mounting: 12mm diameter, 4-hole pattern

Suggested Motors: 14xx – 20xx

Propeller size:

3inch or 76mm propeller 


Weight: 

78g with Adjustable GoPro Hero8 mount and motor screws
68g without GoPro Hero 8 mount 
Downloadable 3D printed TPU snap-in ducts (x4) weigh 24g total – 6g each duct

 

Build include Parts:

Stack: NewBeeDrone Infinity200 
Motors: NewBeeDrone Flow 1408 4150KV
DJI FPV System: CaddX Vista with Nebula Pro 120fps

Propellers: Gemfan Ducted Durable 5 Blade 76mm
GoPro Hero 8 and Hero 9 Mount and 3D printed Battery strap

If you need 3D prints, get them here! 
3D Printed Parts Files
3D Printed Parts Design by Third partyCaddx Peanut Mount by Jason Suter. Thank you Jason!!
Link to manual.


 
Build Video: 

NewBeeDrone CinemAh BNF 4S DJI HD with Crossfire Receiver A New Cinewhoop Design Philosophy To date, many ducted cinewhoop frames have been needlessly heavy. Additionally, existing light cinewhoop frames don’t have guarded props for flying around softer targets. Heavy frames leave you with very little room for adaptabi

NewBeeDrone CinemAh BNF 4S DJI HD with Crossfire Receiver




 
NewBeeDrone CinemAh BNF 4S DJI HD with Crossfire Receiver

A New Cinewhoop Design Philosophy

To date, many ducted cinewhoop frames have been needlessly heavy. Additionally, existing light cinewhoop frames don’t have guarded props for flying around softer targets. Heavy frames leave you with very little room for adaptability to use the frame for your shoots whether it be increased payload capacity or the option for larger batteries. We at NewBeeDrone worked to change that.
The CinemAh Frame - The Most Versatile Cinewhoop Frame
The CinemAh frame is NewBeeDrone’s response to the need for a lighter and more versatile cinewhoop frame to carry a full GoPro. The CinemAh has a unique all-carbon fiber frame structure that allows for easy access to electronics while providing maximum structural strength.
The GoPro Mount (Not Included)
The NewBeeDrone CinemAh cinewhoop TPU GoPro 8 and 9 mounts allow for 4 built-in angles for quick-snap adjustment from 0 deg to 22.5 deg. The capture cam mounts are 2xM2 mounting holes set 20mm apart allowing the community to design any mounting solution for any HD capture cam option. 
Other 3D Printed Accessories (Not Included)
Check out our complete collection of 3D printed accessories for the Cinemah! We&#39ve got snap in ducts, lightweight battery straps, and protective duct coverings in addition to action camera mounts.
 
Electronics Mounting:

2 sets of 1x1inch mounting locations
Front 20x20 location has M3 mounting for a flight controller and ESC stack.
Rear 20x20 location has M2 mounting for Caddx Vista – with rear antenna mount.
Camera mounting – single and double screw camera mounting options.
Note: The frame does not fit an air unit.

Motor Mounting: 12mm diameter, 4-hole pattern

Suggested Motors: 14xx – 20xx

Propeller size:

3inch or 76mm propeller 


Weight: 

78g with Adjustable GoPro Hero8 mount and motor screws
68g without GoPro Hero 8 mount 
Downloadable 3D printed TPU snap-in ducts (x4) weigh 24g total – 6g each duct

 

Build include Parts:

Stack: NewBeeDrone Infinity200 
Motors: NewBeeDrone Flow 1408 4150KV
DJI FPV System: CaddX Vista with Nebula Pro 120fps

Propellers: Gemfan Ducted Durable 5 Blade 76mm
GoPro Hero 8 and Hero 9 Mount and 3D printed Battery strap

If you need 3D prints, get them here! 
3D Printed Parts Files
3D Printed Parts Design by Third partyCaddx Peanut Mount by Jason Suter. Thank you Jason!!
Link to manual.


 
Build Video: 

  NewBeeDrone CinemAh BNF 4S DJI HD with Crossfire Receiver A New Cinewhoop Design Philosophy To date, many ducted cinewhoop frames have been needlessly heavy. Additionally, existing light cinewhoop frames don’t have guarded props for flying around softer targets. Heavy frames leave you with very little room for adapta

NewBeeDrone CinemAh BNF 4S DJI HD with Crossfire Receiver from WREKD Co.

BetaFPV BNF Meteor75 Pro 1S HD 75mm Whoop - HDZero, Frsky

All PRE-ORDERS shipping ASAP!!
All products with batteries must be shipped by a ground shipping method.
The new epic 1S HD digital whoop quadcopter boasts impressive visuals and powerful performance. Upgraded frame from Meteor75 and 45mm props make it the largest 1S whoop quadcopter with greater thrust and lift, equipped with a lighter 1.1g canopy, easy to carry the Walksnail or HDZero Digital VTX system, bringing immersive flight experience and impactful images to the pilots. Combined with F4 1S 5A FC, 1102 22000KV motors and new larger BT2.0 550mAh 1S battery, it makes the Meteor75 Pro HD quadcopter faster, more responsive, and flight time, which would be ideal for FPV racing or acrobatic flying indoors or outdoors.Make sure to check out our other Pre-Built quads and all our BetaFPV gear!
Features

The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks.

It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter.

Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals.

Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better.

Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board.

The various colors of the spare parts including the Meteor75 Pro frame and Micro Canopy Lite, offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.



HDZero Nano Lite Camera is designed for feather-lite drones where every gram counts. At a weight as low as 1.5g, combined with the new Whoop Lite VTX at 4.5g with 0.4g dipole antenna enables a world’s-first production digital FPV solution of about 7g. The HDZero Whoop lite Bundle supports 1-3S power input with 25mW/200mW RF power and is capable of recording in 720P/60FPS with super low latency of less than 19ms. What's more, pilots can activate and configure its OSD function on Betaflight Configurator.

Meteor75 Pro HD VS Meteor75 HD
Upgraded from Meteor75 HD, the Meteor75 Pro HD is the largest 1S HD digital whoop drone with 45mm propellers, which is able to generate more thrust and lift. It comes with a 1.1g Micro Canopy Lite, a 550mAh larger battery, and higher KV motors. The total weight of Meteor75 Pro HD is lighter than Meteor75 HD, making it more agile and easier to handle.

Powerful 1S Drone ComboEven carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots.

Specifications


Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX)

Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero)

Camera Adjustable Angle: 0-40°

Motors: 1102 22000KV Motor

Battery: BT2.0 550mAh 1S Battery

Frame: Meteor75 Pro Brushless Whoop Frame

Propellers: Gemfan 45mm 3-Blade Propellers

Canopy: BETAFPV Micro Canopy Lite

Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero)

Receiver: Serial ELRS 2.4G/SPI Frsky/TBS

FC&ampESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0

VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero)

VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle

Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera

Includes

1x (PRE-ORDER) BetaFPV BNF Meteor75 Pro 1S HD Brushless 75mm Whoop w/ HDZero &amp Nano Cam - Frsky
2x BT2.0 550mAh 1S Battery

1x Type-C USB Cable

1x BT2.0 Battery Charger and Voltage Tester

4x 45mm 3-Blade Props (1.5mm Shaft)

1x Screwdriver

1x VTX USB Cable (Walksnail or HDZero Version)

1x Pack of Screws



All PRE-ORDERS shipping ASAP!! All products with batteries must be shipped by a ground shipping method. The new epic 1S HD digital whoop quadcopter boasts impressive visuals and powerful performance. Upgraded frame from Meteor75 and 45mm props make it the largest 1S whoop quadcopter with greater thrust and lift, equipp

(PRE-ORDER) BetaFPV BNF Meteor75 Pro 1S HD Brushless 75mm Whoop w/ HDZero & Nano Cam - Frsky

(PRE-ORDER) BetaFPV BNF Meteor75 Pro 1S HD Brushless 75mm Whoop w/ HDZ

Pre-Orders shipping ASAP! All products with batteries must be shipped by a ground shipping method.
The new epic 1S HD digital whoop quadcopter boasts impressive visuals and powerful performance. Upgraded frame from Meteor75 and 45mm props make it the largest 1S whoop quadcopter with greater thrust and lift, equipped with a lighter 1.1g canopy, easy to carry the Walksnail or HDZero Digital VTX system, bringing immersive flight experience and impactful images to the pilots. Combined with F4 1S 5A FC, 1102 22000KV motors and new larger BT2.0 550mAh 1S battery, it makes the Meteor75 Pro HD quadcopter faster, more responsive, and flight time, which would be ideal for FPV racing or acrobatic flying indoors or outdoors.Make sure to check out our other Pre-Built quads and all our BetaFPV gear!
Features

The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks.

It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter.

Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals.

Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better.

Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board.

The various colors of the spare parts including the Meteor75 Pro frame and Micro Canopy Lite, offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.



HDZero Nano Lite Camera is designed for feather-lite drones where every gram counts. At a weight as low as 1.5g, combined with the new Whoop Lite VTX at 4.5g with 0.4g dipole antenna enables a world’s-first production digital FPV solution of about 7g. The HDZero Whoop lite Bundle supports 1-3S power input with 25mW/200mW RF power and is capable of recording in 720P/60FPS with super low latency of less than 19ms. What&#39s more, pilots can activate and configure its OSD function on Betaflight Configurator.

Meteor75 Pro HD VS Meteor75 HD
Upgraded from Meteor75 HD, the Meteor75 Pro HD is the largest 1S HD digital whoop drone with 45mm propellers, which is able to generate more thrust and lift. It comes with a 1.1g Micro Canopy Lite, a 550mAh larger battery, and higher KV motors. The total weight of Meteor75 Pro HD is lighter than Meteor75 HD, making it more agile and easier to handle.

Powerful 1S Drone ComboEven carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots.

Specifications


Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX)

Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero)

Camera Adjustable Angle: 0-40°

Motors: 1102 22000KV Motor

Battery: BT2.0 550mAh 1S Battery

Frame: Meteor75 Pro Brushless Whoop Frame

Propellers: Gemfan 45mm 3-Blade Propellers

Canopy: BETAFPV Micro Canopy Lite

Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero)

Receiver: Serial ELRS 2.4G/SPI Frsky/TBS

FC&ampampESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0

VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero)

VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle

Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera

Includes

1x (PRE-ORDER) BetaFPV BNF Meteor75 Pro 1S HD Brushless 75mm Whoop w/ HDZero &ampamp Nano Cam - Frsky
2x BT2.0 550mAh 1S Battery

1x Type-C USB Cable

1x BT2.0 Battery Charger and Voltage Tester

4x 45mm 3-Blade Props (1.5mm Shaft)

1x Screwdriver

1x VTX USB Cable (Walksnail or HDZero Version)

1x Pack of Screws



Pre-Orders shipping ASAP! All products with batteries must be shipped by a ground shipping method. The new epic 1S HD digital whoop quadcopter boasts impressive visuals and powerful performance. Upgraded frame from Meteor75 and 45mm props make it the largest 1S whoop quadcopter with greater thrust and lift, equipped wi

BetaFPV BNF Meteor75 Pro 1S HD Brushless 75mm Whoop w/ HDZero & Nano Cam - Frsky from WREKD Co.

BetaFPV BNF Meteor75 Pro 1S HD Brushless 75mm Whoop w/ HDZero & Nano Cam - Frsky

Pre-Orders shipping ASAP! All products with batteries must be shipped by a ground shipping method.
The new epic 1S HD digital whoop quadcopter boasts impressive visuals and powerful performance. Upgraded frame from Meteor75 and 45mm props make it the largest 1S whoop quadcopter with greater thrust and lift, equipped with a lighter 1.1g canopy, easy to carry the Walksnail or HDZero Digital VTX system, bringing immersive flight experience and impactful images to the pilots. Combined with F4 1S 5A FC, 1102 22000KV motors and new larger BT2.0 550mAh 1S battery, it makes the Meteor75 Pro HD quadcopter faster, more responsive, and flight time, which would be ideal for FPV racing or acrobatic flying indoors or outdoors.Make sure to check out our other Pre-Built quads and all our BetaFPV gear!
Features

The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks.

It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter.

Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals.

Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better.

Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board.

The various colors of the spare parts including the Meteor75 Pro frame and Micro Canopy Lite, offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.



HDZero Nano Lite Camera is designed for feather-lite drones where every gram counts. At a weight as low as 1.5g, combined with the new Whoop Lite VTX at 4.5g with 0.4g dipole antenna enables a world’s-first production digital FPV solution of about 7g. The HDZero Whoop lite Bundle supports 1-3S power input with 25mW/200mW RF power and is capable of recording in 720P/60FPS with super low latency of less than 19ms. What's more, pilots can activate and configure its OSD function on Betaflight Configurator.

Meteor75 Pro HD VS Meteor75 HD
Upgraded from Meteor75 HD, the Meteor75 Pro HD is the largest 1S HD digital whoop drone with 45mm propellers, which is able to generate more thrust and lift. It comes with a 1.1g Micro Canopy Lite, a 550mAh larger battery, and higher KV motors. The total weight of Meteor75 Pro HD is lighter than Meteor75 HD, making it more agile and easier to handle.

Powerful 1S Drone ComboEven carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots.

Specifications


Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX)

Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero)

Camera Adjustable Angle: 0-40°

Motors: 1102 22000KV Motor

Battery: BT2.0 550mAh 1S Battery

Frame: Meteor75 Pro Brushless Whoop Frame

Propellers: Gemfan 45mm 3-Blade Propellers

Canopy: BETAFPV Micro Canopy Lite

Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero)

Receiver: Serial ELRS 2.4G/SPI Frsky/TBS

FC&ampESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0

VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero)

VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle

Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera

Includes

1x (PRE-ORDER) BetaFPV BNF Meteor75 Pro 1S HD Brushless 75mm Whoop w/ HDZero &amp Nano Cam - Frsky
2x BT2.0 550mAh 1S Battery

1x Type-C USB Cable

1x BT2.0 Battery Charger and Voltage Tester

4x 45mm 3-Blade Props (1.5mm Shaft)

1x Screwdriver

1x VTX USB Cable (Walksnail or HDZero Version)

1x Pack of Screws



BetaFPV BNF Pavo25 V2 HD DJI O3 2.5" Cinewhoop


Please note that this version is a kit and does NOT come with an O3 air unit, O3 camera and SanDisk Card. 
At just 150g, Pavo 25 V2 is an optimal 2.5&quot DJI O3 cinewhoop. It&#39s compatible with the Caddx Vista and RunCam Link, Walksnail Avatar HD Pro Kit, and features an innovative PA12 thickened cross-section whoop duct, ideal for 4S power for unbeatable thrust. The camera mount is redesigned for superior protection and boasts COB LED strip for a stylish look. From indoors to out, it&#39s the ultimate DJI O3-compatible quadcopter.
Check out pre-built quads, and the rest of our BetaFPV gear!

Features

Rocket engine-inspired duct design improves lateral stability and increases thrust by 200g compared to without a propeller guard, giving the Pavo25 V2 stronger power and a better flying feel.

Support to carry DJI O3, Walksnail, and HD VTX installations but also works seamlessly with lightweight cameras such as Naked GoPro 12, DJI Action 2, and InstaGo 3.

Innovative Y-shaped CNC Y-shaped CNC metal support structure.Comes with F722 35A FC support great performance capability and high processing speed.

Comes with COB light strip.


 Specifications

Weight: 153g ( no battery)
Recommended Input Voltage: 4S
Recommended battery: 4S 650mah/850mah/930mah 
Prop: GF D63-3B
Motor: 1506 4600KV 

F722 35A AIO Brushless Flight Controller

Item: F722 35A AIO Brushless Flight Controller
Weight: 9.00g (BLHeli_32)
CPU: STM32F722RET6
Six-Axis: ICM42688
Mounting hole size: 26mmx26mm
Firmware version: betaflight_4.3.0_STM32F7X2
OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
Support programmable LED like WS2812 etc
Built-in current sensor
Blackbox: 16MB (V2 with BLHeli_32 ESC included)

Includes

1x BetaFPV BNF Pavo25 V2 HD 4S 2.5&quot Cinewhoop for DJI O3 (without O3 Unit) - Choose Your Receiver


Please note that this version is a kit and does NOT come with an O3 air unit, O3 camera and SanDisk Card.  At just 150g, Pavo 25 V2 is an optimal 2.5" DJI O3 cinewhoop. It's compatible with the Caddx Vista and RunCam Link, Walksnail Avatar HD Pro Kit, and features an innovative PA12 thickened cross-section whoop duct, 

BetaFPV BNF Pavo25 V2 HD 4S 2.5" Cinewhoop for DJI O3 (without O3 Unit) - Choose Your Receiver from WREKD Co.

BetaFPV BNF Pavo25 V2 HD 4S 2.5

BetaFPV BNF Pavo25 V2 HD 4S 2.5" Cinewhoop for DJI O3 (without O3 Unit) - Choose Your Receiver

Five33

At just 150g, Pavo 25 V2 is an optimal 2.5" DJI O3 cinewhoop. It's compatible with the Caddx Vista and RunCam Link, Walksnail Avatar HD Pro Kit, and features an innovative PA12 thickened cross-section whoop duct, ideal for 4S power for unbeatable thrust. The camera mount is redesigned for superior protection and boasts COB LED strip for a stylish look. From indoors to out, it's the ultimate DJI O3-compatible quadcopter.

Features

Rocket engine-inspired duct design improves lateral stability and increases thrust by 200g compared to without a propeller guard, giving the Pavo25 V2 stronger power and a better flying feel.

Support to carry DJI O3, Walksnail, and HD VTX installations but also works seamlessly with lightweight cameras such as Naked GoPro 12, DJI Action 2, and InstaGo 3.

Innovative Y-shaped CNC Y-shaped CNC metal support structure.Comes with F722 35A FC support great performance capability and high processing speed.

Comes with COB light strip.

 

 
 
 Specifications

Weight: 153g ( no battery)
Recommended Input Voltage: 4S
Recommended battery: 4S 650mah/850mah/930mah 
Prop: GF D63-3B
Motor: 1506 4600KV 

F722 35A AIO Brushless Flight Controller

Item: F722 35A AIO Brushless Flight Controller
Weight: 9.00g (BLHeli_32)
CPU: STM32F722RET6
Six-Axis: ICM42688
Mounting hole size: 26mmx26mm
Firmware version: betaflight_4.3.0_STM32F7X2
OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
Support programmable LED like WS2812 etc
Built-in current sensor
Blackbox: 16MB (V2 with BLHeli_32 ESC included)

Includes

1x BetaFPV BNF Pavo25 V2 HD 4S 2.5" Cinewhoop for DJI O3 (without O3 Unit) - Choose Your Receiver


At just 150g, Pavo 25 V2 is an optimal 2.5" DJI O3 cinewhoop. It's compatible with the Caddx Vista and RunCam Link, Walksnail Avatar HD Pro Kit, and features an innovative PA12 thickened cross-section whoop duct, ideal for 4S power for unbeatable thrust. The camera mount is redesigned for superior protection and boasts

BetaFPV BNF Pavo25 V2 HD 4S 2.5" Cinewhoop for DJI O3 (without O3 Unit) - ELRS 2.4GHz

Pre-Order's shipping ASAP! PNP version is in stock and shipping same day! 
Please note that this version is a kit and does NOT come with an O3 air unit, O3 camera and SanDisk Card. 
At just 150g, Pavo 25 V2 is an optimal 2.5" DJI O3 cinewhoop. It's compatible with the Caddx Vista and RunCam Link, Walksnail Avatar HD Pro Kit, and features an innovative PA12 thickened cross-section whoop duct, ideal for 4S power for unbeatable thrust. The camera mount is redesigned for superior protection and boasts COB LED strip for a stylish look. From indoors to out, it's the ultimate DJI O3-compatible quadcopter.
Check out pre-built quads, and the rest of our BetaFPV gear!
Features

Rocket engine-inspired duct design improves lateral stability and increases thrust by 200g compared to without a propeller guard, giving the Pavo25 V2 stronger power and a better flying feel.

Support to carry DJI O3, Walksnail, and HD VTX installations but also works seamlessly with lightweight cameras such as Naked GoPro 12, DJI Action 2, and InstaGo 3.

Innovative Y-shaped CNC Y-shaped CNC metal support structure.Comes with F722 35A FC support great performance capability and high processing speed.

Comes with COB light strip.


 Specifications

Weight: 153g ( no battery)
Recommended Input Voltage: 4S
Recommended battery: 4S 650mah/850mah/930mah 
Prop: GF D63-3B
Motor: 1506 4600KV 

F722 35A AIO Brushless Flight Controller

Item: F722 35A AIO Brushless Flight Controller
Weight: 9.00g (BLHeli_32)
CPU: STM32F722RET6
Six-Axis: ICM42688
Mounting hole size: 26mmx26mm
Firmware version: betaflight_4.3.0_STM32F7X2
OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
Support programmable LED like WS2812 etc
Built-in current sensor
Blackbox: 16MB (V2 with BLHeli_32 ESC included)

Includes

1x BetaFPV BNF Pavo25 V2 HD 4S 2.5" Cinewhoop for DJI O3 (without O3 Unit) - Choose Your Receiver


Pre-Order's shipping ASAP! PNP version is in stock and shipping same day! Please note that this version is a kit and does NOT come with an O3 air unit, O3 camera and SanDisk Card.  At just 150g, Pavo 25 V2 is an optimal 2.5" DJI O3 cinewhoop. It's compatible with the Caddx Vista and RunCam Link, Walksnail Avatar HD Pro

Flywoo

Flywoo BNF FlyLens 85 HD 2" Whoop - HDZero, 2.4GHz ELRS

Introducing the FlyLens 85 brushless whoop the newest 2-inch HDzero drone, developed by Flywoo with international safety regulations in mind. It's equipped with a 1003 motor, 2S battery, and 2-inch bi-blade propeller long-lasting performance. The carbon fiber frame has undergone a special carbon black treatment process. The reverse push propeller structure increases power, reduces noise, and allows for easy adjustment of the battery's center of gravity position.
Equipped with the HDZero Whoop Lite VTX, a cutting-edge digital HD 720p 60fps video transmitter specifically designed for racing and the Runcam HDZero Micro V2 camera, a versatile camera that supports both 4:3 and 16:9 aspect ratios. Whether you're a seasoned racer or a beginner, this setup delivers unparalleled video quality and performance for an immersive and thrilling flying experience.























 Features 

Lightweight and compact design
High-strength protective ring for enhanced durability and safety.
Unique CNC damping platform for smooth and high-quality video recording
Reverse push propeller for stable flight and extended endurance.

FLYLENS 85 drone resources 
A three-point CNC damping platform for the camera
A high-strength PC injection-molded protective ring

A quick-detach structure
Small size, lightweight, less than 100g, lightweight 2-inch drone.
High-strength PC injection-molded protective ring enhances the strength and safety of the drone.

Bottom-mounted transmission PC placement compartment protects and enhances heat dissipation.

Equipped with wireless control neon light strip and can carry external devices.















 

 


Specifications

Model: FlyLens 85 HD O3 2S Brushless Whoop FPV Drone

Frame: FlyLens 85 Standard Frame kit

Electronic: GOKU Versatile F405 1-2S 12A AIO W / build-in ELRS 2.4g RX (MPU6000)
Transmission: HDZero Whoop Lite VTX W/ MIPI 80mm cable 

Camera: RunCam HDZero Micro Camera V2

Propeller: 2015 2-Blade Propeller

Motor: ROBO 1003 14800KV

Antenna: Flywoo 5.8G Light 5.8G 3dBi Brass Antenna UFL

LED: Flywoo Flexible LED + 3.3V Bec 2.7mm

Includes

1x Flywoo BNF FlyLens 85 2S HD 85mm Brushless Whoop w/ HDZero Whoop Lite &amp Micro Cam V2 - ELRS 2.4 GHz


Introducing the FlyLens 85 brushless whoop the newest 2-inch HDzero drone, developed by Flywoo with international safety regulations in mind. It's equipped with a 1003 motor, 2S battery, and 2-inch bi-blade propeller long-lasting performance. The carbon fiber frame has undergone a special carbon black treatment process