FPV Quad Parts

Peripherals and Replacement Parts

Equipment

Equipment Peripherals

Build Page Parts

Build Parts Equipment

Pre-Built Quads and Kits 

Build Page Parts Overflow

Build Parts Equipment Overflow

Compatibility Categories

GEPRC

GEPRC BNF CineLog35 V2 Analog 3.5" Cinewhoop - 2.4GHz ELRS, GPS



















Experience unrivaled performance with the GEPRC CineLog35 V2 6S 3.5" Cinewhoop. This powerful model features an analog &amp micro cam, as well as ELRS 2.4GHz technology, for streamlined flight capabilities and less chance of a fail safe. Fly with confidence as you capture flawless footage with every launch.








Check out our other pre-built quads, as well as the rest of our GEPRC selection.


















Features

New appearance design, strengthening carbon plate, hollow design, injection protection frame, noise reduction design, flight safety, silent.
Adopts the GEP F722-45A AIO V2 high performance flight controller.
SPEEDX2 2105.5 motor with HQ DT90 propeller, stable power output, and smooth flight feel.

Power cable using XT60E1-M plug and carbon plate integrated design, convenient application.
Battery installation method using a tie with 7075 aluminum parts fixed, solid and stable.
Carefully tuned 3.5-inch cinematic FPV quad with flexible and delicate flight feeling.
Pre-Installed with a M8U GPS



 


Specifications

Model: Cinelog35 V2 Analog

Frame: GEP-CL35 V2

Wheelbase: 142mm

Gimbal Plate: 2.0mm

Top Plate: 3.5mm

Bottom Plate: 1.5mm

FC system: GEP-F722-45A AIO V2

MCU: STM32F722RET6

Gyro: ICM 42688-P

OSD: Betaflight OSD w/AT7456E chip

ESC: 8Bit 45A

VTX: GEPRC RAD 1W(UFL)

Camera: Caddx Ratel2

Antenna: GEPRC Peano 5.8 RHCP UFL

Motor: SPEEDX2 2105.5-2150KV (6S)

Propeller: HQProp D-T90MM

GPS: GEP-M8U

Receiver: ELRS2.4G

Weight: 262g
Recommended battery: LiPo 1050mah-1300mah

Flight time: 5′00″ - 8′ 30″

Includes

1x GEPRC BNF CineLog35 V2 Analog 6S 3.5" Cinewhoop - ELRS 2.4GHz (GPS)
2x HQProp D-T90MM（2 pairs）

2x M20 x 250mm battery strap

2x Battery Silicone Pads

1x Set of screws

1x L-shaped screwdriver (1.5mm)

1x L-shaped screwdriver (2mm)

1x L-shaped screwdriver (3mm)

1x M5 wrench

1x plastic tweezers

1x Antenna fixed tube (pair)

1x Keychain

1x GP Camera Mounting Base

1x Naked GP Camera Mounting Base

1x Antenna Mounting Base


Experience unrivaled performance with the GEPRC CineLog35 V2 6S 3.5" Cinewhoop. This powerful model features an analog &amp; micro cam, as well as ELRS 2.4GHz technology, for streamlined flight capabilities and less chance of a fail safe. Fly with confidence as you capture flawless footage with every launch. Check out 

GEPRC BNF CineLog35 V2 Analog 6S 3.5" Cinewhoop - ELRS 2.4GHz (GPS) from WREKD Co.

GEPRC BNF CineLog35 V2 Analog 6S 3.5

GEPRC BNF CineLog35 V2 Analog 6S 3.5" Cinewhoop - ELRS 2.4GHz (GPS)

Gathering the experience and evolution of the GEPRC team in all aspects, CineLog35 V2 is finally launched to the market with better performance. CineLog35 v2 version integrated with O3 VTX. The CineLog35 V2 version of the main carbon plate and injection protection frame increased the 7075 aluminum column for structural

GEPRC CineLog35 V2 Analog GPS 3.5

Recommended GEPRC Storm 6S 1300mAh 120C Lipo Battery for CineLog35 V2.

GEPRC CineLog35 V2 Analog FPV Drone - GEPRC

GEPRC CineLog35 V2 Analog FPV Drone

Pre-Built Quad Kit Type

Pre-Built Quads and Kits

Quad Frame Size

Quad Type

iFlight

iFlight BNF Helion 10 6S 10" HD Cinematic Long Range Quad - DJI O3 Air Unit, ELRS 2.4GHz, GPS

IFLIGHT

This drone was built to redefine Long Range. In order to meet the rising demands for more range, and more flight time while maintaining enough weight, to have excellent stability in even the windiest of conditions. With a prop size of 10 inches, Helion is not only capable of effectively carrying large (Recommended, 4500mAh Lipo and above) batteries but also ensuring great efficiency with ample power. You will have better dive recovery and more overall control than traditional long-range drones. Its unique aerodynamic shell allows for easy maintenance while protecting the cores of the power train. Helion’s distinct frame design was scientifically optimized to balance stability, weight, and rigidity.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products 
Features


Optimised Motors &amp PropellerThis latest XING motor was optimised between thrust and efficiency. Perfectly tuned to the 10 inch Gemfan propellers.


Aero-ShellThe unique aerodynamic shell allows for easy maintenance while protecting the cores of the power train. Users can simply open and close the shell when working on the drone. The idea was to protect the inside but give people full access when maintenance work is being performed on the drone.


Innovative A-Frame for Maximum PerformanceThe frame was scientifically optimised and tested over months to find the balance between stability and weight. The A-Frame design minimises vibrations as well as torsion, one of the biggest problems with larger drones.


USB-C PowerA USB-C Plug was added so you can power your action cam when running out of power. This was also built in for potential upcoming new small cameras making Helion more future proof


DJI O3 HD Air Unit Low-Latency Digital TransmissionUp to 10 km video transmission range, enjoy a crisp and smooth real-time view in your goggles, even in environments with interference. (Source DJI)


4K Stabilized Video with 155° Ultra-Wide AngleTogether with high-grade imaging performance, it delivers exceptional visuals that will keep your audience on the edge of their seats. (Source DJI)


GPS Pre-Installed for More Safety at A DistanceGPS functionality to find your way back on those ultra long range missions. Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour Setup instructions included). Custom iFlight 100mm LR antenna for best signal coverage even at long distances.





Specifications

Product Name: Helion10 O3 6S HD

FC: BLITZ F7 Flight Controller

ESC: BLITZ E55 4-IN-1 2-6S 55A ESC

Video Transmission: DJI O3 Air Unit

Geometry: A-Frame

Frame: 418mm wheelbase

Motor: XING2 3110 900KV motors

Prop: GEMFAN 1050 propellers

Weight: 970±20g (Without Battery)

Dimensions (L×W×H)：324x264x63mm

Max Speed: 140km/h

Maximum Takeoff Altitude: 7000 m

Max Hover Time: Approx. 26mins with 6S Lipo 5600mAh battery / 30mins with 6S
8000mAh Li-ion battery

Max Cruising Time: Approx. 23mins with 6S Lipo 5600mAh battery / 26mins with
6S 8000mAh Li-ion battery

Operating Temperature Range: -20° to 40° C

Antennas: Dual Antennas

GNSS: GPS+SBAS+Galileo+QZSS+Glonass

Video Transmission 

Product Name: DJI O3 Air Unit

Weight: Approx. 36.4 grams（headband included）

Dimensions (L×W×H): L32.5x W30.5xH 14.5mm

Communication Bandwidth： Max 40 MHz

FOV (single screen): 155°

Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz

End-to-End Latency

With DJI FPV Goggles V2:

810p/120fps Video Transmission Quality: The latency is lower than 28 ms.

810p/60fps Video Transmission Quality: The latency is lower than 40 ms.

With DJI Goggles 2:

1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.

1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.

Max Video Transmission Bitrate: 50 Mbps

Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)

Operating Temperature Range: -10º to 40º C (14° to 104° F)

Power Input: 7.4-26.4 V

Audio Transmission: N/A

END-TO-END LATENCY

With DJI FPV Goggles V2:

810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.

With DJI Goggles 2:

1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.


 Includes

1x Helion 10 6S HD

2x Battery pad

2x GEMFAN 1050 propellers(Pairs)

2x Battery strap

1xx Screw bag


This drone was built to redefine Long Range. In order to meet the rising demands for more range, and more flight time while maintaining enough weight, to have excellent stability in even the windiest of conditions. With a prop size of 10 inches, Helion is not only capable of effectively carrying large (Recommended, 450

iFlight BNF Helion 10 6S 10" HD Cinematic Long Range Quad w/DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz (GPS)

iFlight BNF Helion 10 6S 10" HD Cinematic Long Range Quad w/DJI O3 Air

HELION - The Long Range flagship by 2RAW and Flight.&nbsp

HELION - The Long Range flagship by 2RAW and Flight. 

iFlight 2Raw Helion 10 Long Range 10" 6S BNF HD w/ DJI O3

iFlight 2Raw Helion 10 Long Range 10&quot 6S BNF HD w/ DJI O3

RaceDayQuads

Pre-Orders shipping ASAP!
This drone was built to redefine Long Range. In order to meet the rising demands for more range, and more flight time while maintaining enough weight, to have excellent stability in even the windiest of conditions. With a prop size of 10 inches, Helion is not only capable of effectively carrying large (Recommended, 4500mAh Lipo and above) batteries but also ensuring great efficiency with ample power. You will have better dive recovery and more overall control than traditional long-range drones. Its unique aerodynamic shell allows for easy maintenance while protecting the cores of the power train. Helion’s distinct frame design was scientifically optimized to balance stability, weight, and rigidity.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products 
Features


Optimised Motors &amp PropellerThis latest XING motor was optimised between thrust and efficiency. Perfectly tuned to the 10 inch Gemfan propellers.


Aero-ShellThe unique aerodynamic shell allows for easy maintenance while protecting the cores of the power train. Users can simply open and close the shell when working on the drone. The idea was to protect the inside but give people full access when maintenance work is being performed on the drone.


Innovative A-Frame for Maximum PerformanceThe frame was scientifically optimised and tested over months to find the balance between stability and weight. The A-Frame design minimises vibrations as well as torsion, one of the biggest problems with larger drones.


USB-C PowerA USB-C Plug was added so you can power your action cam when running out of power. This was also built in for potential upcoming new small cameras making Helion more future proof


DJI O3 HD Air Unit Low-Latency Digital TransmissionUp to 10 km video transmission range, enjoy a crisp and smooth real-time view in your goggles, even in environments with interference. (Source DJI)


4K Stabilized Video with 155° Ultra-Wide AngleTogether with high-grade imaging performance, it delivers exceptional visuals that will keep your audience on the edge of their seats. (Source DJI)


GPS Pre-Installed for More Safety at A DistanceGPS functionality to find your way back on those ultra long range missions. Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour Setup instructions included). Custom iFlight 100mm LR antenna for best signal coverage even at long distances.





Specifications

Product Name: Helion10 O3 6S HD

FC: BLITZ F7 Flight Controller

ESC: BLITZ E55 4-IN-1 2-6S 55A ESC

Video Transmission: DJI O3 Air Unit

Geometry: A-Frame

Frame: 418mm wheelbase

Motor: XING2 3110 900KV motors

Prop: GEMFAN 1050 propellers

Weight: 970±20g (Without Battery)

Dimensions (L×W×H)：324x264x63mm

Max Speed: 140km/h

Maximum Takeoff Altitude: 7000 m

Max Hover Time: Approx. 26mins with 6S Lipo 5600mAh battery / 30mins with 6S
8000mAh Li-ion battery

Max Cruising Time: Approx. 23mins with 6S Lipo 5600mAh battery / 26mins with
6S 8000mAh Li-ion battery

Operating Temperature Range: -20° to 40° C

Antennas: Dual Antennas

GNSS: GPS+SBAS+Galileo+QZSS+Glonass

Video Transmission 

Product Name: DJI O3 Air Unit

Weight: Approx. 36.4 grams（headband included）

Dimensions (L×W×H): L32.5x W30.5xH 14.5mm

Communication Bandwidth： Max 40 MHz

FOV (single screen): 155°

Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz

End-to-End Latency

With DJI FPV Goggles V2:

810p/120fps Video Transmission Quality: The latency is lower than 28 ms.

810p/60fps Video Transmission Quality: The latency is lower than 40 ms.

With DJI Goggles 2:

1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.

1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.

Max Video Transmission Bitrate: 50 Mbps

Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)

Operating Temperature Range: -10º to 40º C (14° to 104° F)

Power Input: 7.4-26.4 V

Audio Transmission: N/A

END-TO-END LATENCY

With DJI FPV Goggles V2:

810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.

With DJI Goggles 2:

1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.


 Includes

1x Helion 10 6S HD

2x Battery pad

2x GEMFAN 1050 propellers(Pairs)

2x Battery strap

1xx Screw bag


Pre-Orders shipping ASAP! This drone was built to redefine Long Range. In order to meet the rising demands for more range, and more flight time while maintaining enough weight, to have excellent stability in even the windiest of conditions. With a prop size of 10 inches, Helion is not only capable of effectively carryi

iFlight BNF Helion 10 6S 10

Introducing the iFlight Chimera 7" Long Range, Long Distance Drone! A super efficient iFlight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want! Super stiff frame for minimum resonance and 2806.5 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above. GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts included to cover you and your antenna dead ends just in case. GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (additional).Check out the entire Chimera7 Collection and all Replacement Parts!We also carry the Chimera4 LR collection! Check out all our Digital BNF/PNP/RTFs and our other iFlight Products! HIGHLIGHTS: - 6mm rigid arm design for more stiffness - Top- and bottom battery mount option - XING 2806.5 efficient wide stator motors - GPS pre-installed for more safety at distance - GoPro TPU bottom stand (GoPro protector not included) - 360° TPU protection, DJI cam protection and antenna mounts - DJI FPV Air Unit, buttery-smooth 720p\120fps FPV feed (TPU soft mounted) - No props in view (DJI Air unit record in 1080p/60fps) - Battery voltage LED status light (illuminated IF logo on the bottom) PRE-TUNED & PRE-SETUP: - Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience! To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps" - Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess! Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode" - GPS Rescue is OFF by default to prevent from unwanted or unexpected drone behaviour. Please check our linked article on "GPS Rescue Mode // Setup" FRAME // ：Chimera7 - Wheelbase: 320mm - Main body dimension: 258*199mm - Bottom to top distance: 20mm - Arm thickness: 6mm - Bottom plate thickness: 3mm - Top plate thickness: 2mm - Upper(middle) plate thickness: 3mm - Camera plate thickness: 3mm (included TPU inserts) ELECTRONICS // SucceX-D F7 V2.1 Stack (50A 4-in-1 ESC)： SucceX-D F7 V2.1 TwinG: - MCU: 216MHz STM32F722 - Gyro：2x ICM20689 - Baro: YES - Blackbox：32MB - Betaflight OSD: YES - BEC: 5V 2.5A / 9V 2.5A - Current sensor scale: 100 - Inverter for SBUS input (UART2-RX) - Smartaudio & Tramp VTX protocol supported - Beeper pad : Yes - RSSI input pad: No - UARTs：5 - Motor outputs: 8 - 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5) - 6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V) - BLHeli32 Telemetry：RX5 - Input voltage：recommended 2-6S, MAX 8S - Firmware Target: IFLIGHT_F722_TWING - Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm - Dimensions: 36*36mm - Weight: 7.5g - USB type-C ESC // SucceX 50A: - MCU: STM32F051 - Up tp 48kHz PWM frequency - Capacitance: 470uF/50V - Current Sensor: Yes - Input: 2-6S LIPO - Constant: 50A / Burst: 60A - BlHeli32 telemetry: Yes - BEC: No - Supports up to Dshot1200, Proshot, Oneshot, Multishot - Target: iFlight-BL32-4IN1 - Weight: 14.4g - Mounting pattern: 30.5*30.5mm/Φ3mm - Dimensions: 43*39mm (including the power pads) BNF // Parts list (Build): Prebuilt and indoor tested Quadcopter - 1x Chimera7 frame - 1x GoPro TPU bottom stand incl. lock screw - 1x DJI FPV camera - 1x DJI FPV Air Unit Module - 2x Albatross LHCP RP-SMA 5.8g 150mm antenna - 2 sets x Gemfan tri-blade 7040 props (Set of 4 - Color may vary) - 4x 20*250mm Microfiber PU Leather Battery Strap (Color May Vary)

IFlight Helion 10 6S HD 10 inch Long Range Drone W/ DJI O3 FPV System - Choose Receiver

iFlight BNF Helion 10 6S 10" HD Cinematic Long Range Quad w/DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz (GPS) from WREKD Co.

BetaFPV

BetaFPV RTF Aquila16 FPV Analog Kit

BETAFPV Hobby

The Aquila16 FPV kit is a more advanced kit for beginners. It's an inverted quadcopter with a modular aerodynamic design. Fly for up to 8 mins, covering a maximum distance of 200 meters. Enjoy stable hovering and enhanced frame protection, allowing for consistent flight practice and better control. The kit includes the VR03 FPV Goggles for recording your flying and a Literadio 2 SE Radio Transmitter with the latest ELRS 3.0 firmware. All you need is in one pack! Accelerate your FPV learning curve and become a pro sooner with this kit.

Bullet Point

The Aquila16 FPV Kit excels in hover capability for assisted flight, ensuring safe and effortless flight for worry-free learning.
Built with durable PA12 material, the Aquila16 frame has excellent impact resistance in drop &amp impact and reduces the risk of damage, providing you more peace learning of mind.
With a 1100mAh battery, it offers a flight time of 8 minutes and a maximum flight distance of 200 meters. For those seeking advanced flight modes like freestyle or racing, opting for a 650 battery is recommended.
This kit offers 3 fly and speed modes, catering from novice to pro and gradually unlocking advanced skills, all in one kit.

The VR03 FPV Goggles feature a Micro SD card slot for easy video recording and support compatibility with most Analog VTXs in the market.
The Literadio2 SE Transmitter supports the latest ELRS 3.0 firmware, enabling compatibility with popular FPV simulators like DRL/DCL/VelociDrone/Liftoff.

All components, including the quadcopter, radio transmitter, FPV goggles, and accessories, are conveniently packed in a portable EVA storage bag for easy transportation and enhanced equipment protection.

Specification

Item: Aquila16 FPV Kit
Battery: Aquila16 Special Battery|1100mAh (Default), 650mAh (Optional)
Camera: C02
Camera Angle Adjustment: 15°-30°
Charger Used: BT2.0 Battery Charger and Voltage Tester V2
Flight Controller: Aquila16 V1.0
Flight Modes: N/S/M Mode

Flight Time(4.35V-3.4V): 8 mins
Frame Material: Black PA12
Goggles: VR03 FPV Goggles 
Motors: 1102|18000KV
Power Connector: BT2.0 Connector
Propellers: Beta-45mm 3-Blades Props
Radio Transmitter: LiteRadio 2 SE Radio Transmitter
Receiver: Serial ELRS 2.4G 3.0 Version
Receiver Binding: Power up 3 times
Video Transmitter(VTX): Aquila 25-350mW VTX
VTX Power and Range: 25mW (Range:80m), 350mW (Range:200m)
Wheelbase: 86mm
Weight(Without Battery): 47.1g
Takeoff Weight(With 1100mAh Battery): 72.5g

From Zero To Hero







Aquila16 FPV Kit
 Cetus Pro FPV Kit

Cetus X FPV Kit


Battery
Aquila16 Exclusive Battery|1100mAh (Default), 650mAh (Optional)
BT2.0 450mAh 1S 30C Battery


Flight Time(4.35V-3.4V)
8 mins (Default battery)
4-5min


Motors
1102|18000KV Brushless motor
1102|18000KV Brushless 
1103|11000KV Brushless motor


Video Transmitter
Aquila 25-350mW VTX
25mW（AIO FC）
M04 25-400mW VTXCetus 25-350mW VTX V2


VTX Power and Range
25mW (Range:80m)350mW (Range:200m)
25mW (Range:80m)
M04 VTX: 25mW（Range:80m）400mW（Range:500m）Cetus VTX：25mW（Range:80m）350mW（Range:200m）


Recording Funtion
Support
Not Support
Support





Fly Further, Fly Longer

With an impressive 8 mins flight time, you can enjoy endless practice sessions and a flight distance of up to 200m indoors or outdoors. Enjoy uninterrupted flights, enabling you to concentrate on refining your piloting skills. The kit features a high-power, low-latency 350mW video transmission system, guaranteeing real-time video transmission with stable signals up to 200 meters. Say goodbye to lag and immerse yourself in the thrill of the flight.

Auxiliary Flight Function
The Aquila16 FPV Kit excels in hover capability for assisted flight, ensuring safe and effortless flight for worry-free learning. Built-in highly precise barometer to detect the height, it benefits from great stability due to its position hold mode, and auto-hovering, which enables the drone to stay at the current height. This function guarantees emergency landing in situations of lost control or low battery. Meanwhile, its stable flight characteristics allow for capturing stunning footage with utmost precision using the VR03 FPV Goggles. Experience an immense amount of enjoyment and ease of flight. 

Note: The position hold function is only available in N mode.
Designed to Make Flying Easier 

Every aspect of its design embodies making flying easier for beginner-friendly. The inclusion of an inverted duct system enhances thrust and stability, enabling the drone to achieve superior flight performance with precision. The fixed configuration port and modular battery minimize redundancy designs, making installation simple and hassle-free. The duct guard design ensures safe flights by protecting the propellers, equipped to handle unexpected obstacles.

The receiver binding needs to power up 3 times and the battery's first power-up may result in a tight fit, requiring a certain technique for insertion and removal, please refer to this video.
Fly Indoor and Outdoor 
The Aquila16 FPV Kit provides an exhilarating flying experience for all, regardless of age or skill level. The durable construction guarantees lasting performance, while intuitive controls offer precise maneuverability, ensuring a worry-free indoor and outdoor flying experience while capturing breathtaking moments with a high-quality camera and enjoying the thrill of real-time FPV. Effortless setup allows you to fully immerse yourself in the sheer joy of flight, unlocking boundless creative possibilities. 

Various Modes, Accessible to All

The Aquila16 Brushless Quadcopter offers N/S/M 3 flight modes and supports 3 different speeds with SLOW/MID/FAST. With Turtle Mode, no burden to fly away, and there is no need to walk away to correct the position manually to flip it over and resume flying when the quadcopter falls to the ground and upside down. Whether you're a seasoned FPV pilot or a complete beginner, the Aquila16 FPV Kit empowers everyone to fly confidently from day one. 

Below is the table for the different speeds under N modes maximum throttle.



SLOW
MID
FAST


1.25m/s
3.33m/s
5m/s




The Aquila16 FPV Kit comes with a default 1100mAh battery, ideal for beginners seeking a smooth flying experience in N/S mode. However, for those looking to advance their freestyle and racing flight skills in M Mode, the 650mAh version battery is more suitable, it needs to be purchased separately.
Recording Every Flight Moment

Pilots can record and save flying videos on a Micro SD card and easily replay them using the VR03 FPV Goggles which feature a high-quality 5.8G 3dBi antenna for stable video transmission and vivid images. Its omnidirectional design ensures equal signal radiation and reception in all 360-degree horizontal directions. The replaceable antenna allows pilots to experiment with different options and adjust the angle as needed. With 4.3 inches 800*480px HD high brightness LCD, VR03 Goggles will show you a bright world. 

LiteRadio 2 SE Radio Transmitter
Built-in 1000 mAh 1S battery, LiteRadio 2 SE increases the endurance to 8 hours. It comes preloaded with the factory default ELRS 3.0 firmware, offering a transmitting power of 100mW, which brings a wider operating range. Updates with BETAFPV self-developed LiteRadio System, enabling pilots to conveniently perform Joystick Calibration and Firmware Upgrades directly on the transmitter, enhancing usability and ease of use.

Note: This LR 2 SE radio TX mode of Aquila16 FPV Kit is Mode2 which is the left-hand throttle.
FPV Simulator Supported
First time flying a quadcopter? You can learn and practice flying a quadcopter through an FPV simulator before real flying. LiteRadio2 SE radio transmitter can be used as a USB Joystick when connected to the computer. So it's available to play FPV simulators like DRL/DCL/VelociDrone/Liftoff. More convenient for practicing and charging at the same time. Here is the display of Liftoff. Download Liftoff here.  And this LiftOFF simulator has launched the Aquila16 quadcopter now. Click to learn more.

 Note: This radio transmitter isn't compatible with Windows 11/Windows 10 systems running on AMD CPUs. If you wanna connect to a simulator, you will need to revert it to the ELRS 2.0 firmware.
 

Recommended Parts


Quadcopter: Aquila16 Brushless Quadcopter
Battery: Aquila16 Exclusive Battery (2PCS)
Props: Beta-45mm 3-Blades Propellers (1.5mm Shaft 4PCS)
Adapter Cable: BT2.0 Female-Male Adapter Cable

FAQ


Download the Manual for the Aquila16 FPV Kit.

Donwload the Firmware for Aquila16 FPV Kit.

How to replace the VTX Module of Aquila16 FPV Kit.
There is a risk of battery detachment during severe crashes.
Camera angle adjustment: The canopy is fixed, and the camera angle can be adjusted by loosening or tightening the screws on both sides.


ExpressLRS is the popular radio link now. Know more about ExpressLRS here.

The LiteRadio 2 SE Radio Transmittercurrent factory default firmware is ELRS V2, and it can be upgraded to the beta version of ELRS V3 firmware. For detailed instructions, please visit: link to the update guide.

Package

1 * Aquila16 Brushless Quadcopter
1 * LiteRadio 2 SE Radio Transmitter
1 * VR03 FPV Goggles
4 * Beta-45mm 3-Blades Props (Spare Set)
2 * Aquila16 Exclusive Battery|1100mAh
2 * Charging Adapter Cable
1 * BT2.0 Battery Charger and Voltage Tester V2
1 * 4Pin Adapter Cable
1 * USB Charging Cable (Type-C)

1 * Cross Screwdriver
1 * Exclusive Screw Set (Spare)
1 * Prop Removal Tool

1 * Portable Storage Bag
1 * User Manual
1 * USB Type-C Adapter Board (Used in connection with the 4Pin adapter cable for FC to configuration)



The Aquila16 FPV kit is a more advanced kit for beginners. It's an inverted quadcopter with a modular aerodynamic design. Fly for up to 8 mins, covering a maximum distance of 200 meters. Enjoy stable hovering and enhanced frame protection, allowing for consistent flight practice and better control. The kit includes the

Aquila16 FPV Kit

The Aquila16 FPV kit is a more advanced kit for beginners. It's an inverted quadcopter with a modular aerodynamic design. Fly for up to 8 mins, covering a maximum distance of 200 meters. Enjoy stable hovering and enhanced frame protection, allowing for consistent flight practice and better control. The kit includes the

BetaFPV Aquila16 FPV RTF Kit ELRS 2.4GHz v3.0 with Goggles & Controller

Five33

The Aquila16 FPV kit is a more advanced kit for beginners. It's an inverted quadcopter with a modular aerodynamic design. Fly for up to 8 mins, covering a maximum distance of 200 meters. Enjoy stable hovering and enhanced frame protection, allowing for consistent flight practice and better control. The kit includes the VR03 FPV Goggles for recording your flying and a Literadio 2 SE Radio Transmitter with the latest ELRS 3.0 firmware. All you need is in one pack! Accelerate your FPV learning curve and become a pro sooner with this kit.

Bullet Point

The Aquila16 FPV Kit excels in hover capability for assisted flight, ensuring safe and effortless flight for worry-free learning.
Built with durable PA12 material, the Aquila16 frame has excellent impact resistance in drop &amp impact and reduces the risk of damage, providing you more peace learning of mind.
With a 1100mAh battery, it offers a flight time of 8 minutes and a maximum flight distance of 200 meters. For those seeking advanced flight modes like freestyle or racing, opting for a 650 battery is recommended.
This kit offers 3 fly and speed modes, catering from novice to pro and gradually unlocking advanced skills, all in one kit.

The VR03 FPV Goggles feature a Micro SD card slot for easy video recording and support compatibility with most Analog VTXs in the market.
The Literadio2 SE Transmitter supports the latest ELRS 3.0 firmware, enabling compatibility with popular FPV simulators like DRL/DCL/VelociDrone/Liftoff.

All components, including the quadcopter, radio transmitter, FPV goggles, and accessories, are conveniently packed in a portable EVA storage bag for easy transportation and enhanced equipment protection.

Specification

Item: Aquila16 FPV Kit
Battery: Aquila16 Special Battery|1100mAh (Default), 650mAh (Optional)
Camera: C02
Camera Angle Adjustment: 15°-30°
Charger Used: BT2.0 Battery Charger and Voltage Tester V2
Flight Controller: Aquila16 V1.0
Flight Modes: N/S/M Mode

Flight Time(4.35V-3.4V): 8 mins
Frame Material: Black PA12
Goggles: VR03 FPV Goggles 
Motors: 1102|18000KV
Power Connector: BT2.0 Connector
Propellers: Beta-45mm 3-Blades Props
Radio Transmitter: LiteRadio 2 SE Radio Transmitter
Receiver: Serial ELRS 2.4G 3.0 Version
Receiver Binding: Power up 3 times
Video Transmitter(VTX): Aquila 25-350mW VTX
VTX Power and Range: 25mW (Range:80m), 350mW (Range:200m)
Wheelbase: 86mm
Weight(Without Battery): 47.1g
Takeoff Weight(With 1100mAh Battery): 72.5g

From Zero To Hero








Aquila16 FPV Kit
 Cetus Pro FPV Kit

Cetus X FPV Kit


Battery
Aquila16 Exclusive Battery|1100mAh (Default), 650mAh (Optional)
BT2.0 450mAh 1S 30C Battery


Flight Time(4.35V-3.4V)
8 mins (Default battery)
4-5min


Motors
1102|18000KV Brushless motor
1102|18000KV Brushless 
1103|11000KV Brushless motor


Video Transmitter
Aquila 25-350mW VTX
25mW（AIO FC）
M04 25-400mW VTXCetus 25-350mW VTX V2


VTX Power and Range
25mW (Range:80m)350mW (Range:200m)
25mW (Range:80m)
M04 VTX: 25mW（Range:80m）400mW（Range:500m）Cetus VTX：25mW（Range:80m）350mW（Range:200m）


Recording Funtion
Support
Not Support
Support






Fly Further, Fly Longer

With an impressive 8 mins flight time, you can enjoy endless practice sessions and a flight distance of up to 200m indoors or outdoors. Enjoy uninterrupted flights, enabling you to concentrate on refining your piloting skills. The kit features a high-power, low-latency 350mW video transmission system, guaranteeing real-time video transmission with stable signals up to 200 meters. Say goodbye to lag and immerse yourself in the thrill of the flight.

Auxiliary Flight Function
The Aquila16 FPV Kit excels in hover capability for assisted flight, ensuring safe and effortless flight for worry-free learning. Built-in highly precise barometer to detect the height, it benefits from great stability due to its position hold mode, and auto-hovering, which enables the drone to stay at the current height. This function guarantees emergency landing in situations of lost control or low battery. Meanwhile, its stable flight characteristics allow for capturing stunning footage with utmost precision using the VR03 FPV Goggles. Experience an immense amount of enjoyment and ease of flight. 

Note: The position hold function is only available in N mode.
Designed to Make Flying Easier 

Every aspect of its design embodies making flying easier for beginner-friendly. The inclusion of an inverted duct system enhances thrust and stability, enabling the drone to achieve superior flight performance with precision. The fixed configuration port and modular battery minimize redundancy designs, making installation simple and hassle-free. The duct guard design ensures safe flights by protecting the propellers, equipped to handle unexpected obstacles.

The receiver binding needs to power up 3 times and the battery's first power-up may result in a tight fit, requiring a certain technique for insertion and removal, please refer to this video.
Fly Indoor and Outdoor 
The Aquila16 FPV Kit provides an exhilarating flying experience for all, regardless of age or skill level. The durable construction guarantees lasting performance, while intuitive controls offer precise maneuverability, ensuring a worry-free indoor and outdoor flying experience while capturing breathtaking moments with a high-quality camera and enjoying the thrill of real-time FPV. Effortless setup allows you to fully immerse yourself in the sheer joy of flight, unlocking boundless creative possibilities. 

Various Modes, Accessible to All

The Aquila16 Brushless Quadcopter offers N/S/M 3 flight modes and supports 3 different speeds with SLOW/MID/FAST. With Turtle Mode, no burden to fly away, and there is no need to walk away to correct the position manually to flip it over and resume flying when the quadcopter falls to the ground and upside down. Whether you're a seasoned FPV pilot or a complete beginner, the Aquila16 FPV Kit empowers everyone to fly confidently from day one. 

Below is the table for the different speeds under N modes maximum throttle.




SLOW
MID
FAST


1.25m/s
3.33m/s
5m/s





The Aquila16 FPV Kit comes with a default 1100mAh battery, ideal for beginners seeking a smooth flying experience in N/S mode. However, for those looking to advance their freestyle and racing flight skills in M Mode, the 650mAh version battery is more suitable, it needs to be purchased separately.
Recording Every Flight Moment

Pilots can record and save flying videos on a Micro SD card and easily replay them using the VR03 FPV Goggles which feature a high-quality 5.8G 3dBi antenna for stable video transmission and vivid images. Its omnidirectional design ensures equal signal radiation and reception in all 360-degree horizontal directions. The replaceable antenna allows pilots to experiment with different options and adjust the angle as needed. With 4.3 inches 800*480px HD high brightness LCD, VR03 Goggles will show you a bright world. 

LiteRadio 2 SE Radio Transmitter
Built-in 1000 mAh 1S battery, LiteRadio 2 SE increases the endurance to 8 hours. It comes preloaded with the factory default ELRS 3.0 firmware, offering a transmitting power of 100mW, which brings a wider operating range. Updates with BETAFPV self-developed LiteRadio System, enabling pilots to conveniently perform Joystick Calibration and Firmware Upgrades directly on the transmitter, enhancing usability and ease of use.

Note: This LR 2 SE radio TX mode of Aquila16 FPV Kit is Mode2 which is the left-hand throttle.
FPV Simulator Supported
First time flying a quadcopter? You can learn and practice flying a quadcopter through an FPV simulator before real flying. LiteRadio2 SE radio transmitter can be used as a USB Joystick when connected to the computer. So it's available to play FPV simulators like DRL/DCL/VelociDrone/Liftoff. More convenient for practicing and charging at the same time. Here is the display of Liftoff. Download Liftoff here.


Recommended Parts


Quadcopter: Aquila16 Brushless Quadcopter
Battery: Aquila16 Exclusive Battery (2PCS)

FAQ


Download the Manual for the Aquila16 FPV Kit.

Donwload the Firmware for Aquila16 FPV Kit.
There is a risk of battery detachment during severe crashes.
Camera angle adjustment: The canopy is fixed, and the camera angle can be adjusted by loosening or tightening the screws on both sides.


ExpressLRS is the popular radio link now. Know more about ExpressLRS here.

The LiteRadio 2 SE Radio Transmittercurrent factory default firmware is ELRS V2, and it can be upgraded to the beta version of ELRS V3 firmware. For detailed instructions, please visit: link to the update guide.

Package

1 * Aquila16 Brushless Quadcopter
1 * LiteRadio 2 SE Radio Transmitter
1 * VR03 FPV Goggles
4 * Beta-45mm 3-Blades Props (Spare Set)
2 * Aquila16 Exclusive Battery|1100mAh
2 * Charging Adapter Cable
1 * BT2.0 Battery Charger and Voltage Tester V2
1 * 4Pin Adapter Cable
1 * USB Charging Cable (Type-C)

1 * Cross Screwdriver
1 * Exclusive Screw Set (Spare)
1 * Prop Removal Tool

1 * Portable Storage Bag
1 * User Manual
1 * USB Type-C Adapter Board (Used in connection with the 4Pin adapter cable for FC to configuration)



BETAFPV Aquila16 FPV Kit

BETAFPV

The BETAFPV Aquila16 FPV Kit is an advanced option for beginner pilots.&nbsp

The BETAFPV Aquila16 FPV Kit is an advanced option for beginner pilots. 

BETAFPV Aquila16 FPV Kit 

GEPRC BNF CineLog 30 HD 3" Cinewhoop

Developed by GEPRC, the CineLog30 is one of the best sub-250g FPV pusher drones in the current market! Analog and HD versions are available!

GEPRC CineLog 30 3" 4S HD CineWhoop Drone w/ Caddx Polar Vista 

GEPRC CineLog 30 3&quot 4S HD CineWhoop Drone w/ Caddx Polar Vista 

1.Newly Lightweight Design

The new design made the drone smaller and lighter. The most of important, CineLog30 can take off with 4s 660mah battery only 222.5 grams

2.Newly Noise Reduction Design
Unique noise reduction design can make CinLog30 noise much less than another Whoop Quadcopter

3.Carrying HD Digital VTX And Newly FPV Camera
Making video more clear and the perfect night vision images. Let you get a great flight experience.

4.Customized Mounting base
Perfectly suitable for naked camera GP8 and INSTA 360 GO2 camera

5.Upgrade Platform Design
Make the shooting and recording effect more stable

6.Backward Push Design
Bring higher flexibility, more stable freestyle flight experience and better shock absorption ability.

7.New personalized color matching
Show your difference

1.Newly Lightweight Design  The new design made the drone smaller and lighter. The most of important, CineLog30 can take off with 4s 660mah battery only 222.5 grams  2.Newly Noise Reduction Design Unique noise reduction design can make CinLog30 noise much less than another Whoop Quadcopter  3.Carrying HD Digital VTX And Newly FPV Camera Making video more clear and the perfect night vision images. Let you get a great flight experience.  4.Customized Mounting base Perfectly suitable for naked camera GP8 and INSTA 360 GO2 camera  5.Upgrade Platform Design Make the shooting and recording effect more stable  6.Backward Push Design Bring higher flexibility, more stable freestyle flight experience and better shock absorption ability.  7.New personalized color matching Show your difference

GEPRC CineLog30 HD w/ Runcam Link Wasp Digital HD System - GEPRC

GEPRC CineLog30 HD w/ Runcam Link Wasp Digital HD System

Developed from the Cinelog25, the GEPRC CineLog30 is a dream of a pusher quad with incredibly stable HD video. It's perfect for carrying a Naked GoPro, SMO, or other actions cameras and is capable of freestyle or cinematic flight.  Built on the new ultra light and durable GEP-CL30 frame, it features more powerful 1404 

GEPRC BNF CineLog 30 HD 3

GEPRC BNF CineLog 35 Performance Analog 3.5" Quadcopter

The CineLog35 Performance version is now released in two versions: Runcam Link Wasp and Analog version. There are also 3 receiver options. The CineLog35 Performance version is optimized and upgraded based on the standard version. The CineLog35 is designed with lighter weight and longer endurance. The concept of the Per

GEPRC CineLog35 Performance Edition 3.5

Recommended GEPRC 6S 1550mAh Li-HV Battery for CineLog35 Performance

GEPRC CineLog35 Performance Analog FPV Drone - GEPRC

GEPRC CineLog35 Performance Analog FPV Drone

The CineLog35 Performance version is now released in three versions: VISTA Nebula PRO,AVATAR HD 1080P and Analog version. There are also 4 receiver options. The CineLog35 Performance version is optimized and upgraded based on the standard version. The CineLog35 is designed with lighter weight and longer endurance. The 

The CineLog35 Performance version RTF is optimized and upgraded based on the standard version. The CineLog35 is designed with lighter weight and longer endurance, and the concept of the Performance version is to maximize Racing performance and achieve perfection with the existing frame size.

The CineLog35 Performance version RTF is optimized and upgraded based on the standard version. The CineLog35 is designed with lighter weight and longer endurance, and the concept of the Performance version is to maximize Racing performance and achiev

GEPRC CineLog 35 P 3.5" Cinewhoop Drone Analog w/ Caddx Ratel 2 - Performance Edition - 6S 

GEPRC CineLog 35 P 3.5&quot Cinewhoop Drone Analog w/ Caddx Ratel 2 - Performance Edition - 6S 

iFlight BNF Nazgul Evoque F5X HD 5" Squashed X Quadcopter

Our best pre-built drone just got better! Another breakthrough in FPV visuals from DJI with our upgraded frame and electronics. A new standard of Bind-And-Fly drones that are simple to get started with but the durability and performance for enthusiasts. Welcome to the iFlight experience! Browse here The iFlight Nazgul 

iFlight Nazgul Evoque F5X V2 6S Squashed-X Geometry w/ DJI O3 HD Camera System - Choose Version

iFlight BNF Nazgul Evoque F5D HD 5" Deadcat Quadcopter

iFlight Nazgul Evoque F5D V2 6S Deadcat Geometry w/ DJI O3 HD Camera System - Choose Version

BetaFPV RTF Cetus X FPV Analog Kit

Whether skillful pilots or new beginners, Cetus X FPV Kit, as the advanced 2S power whoop bundle, is a completely primary choice to reach a higher stage. From its unparalleled control to its exciting flying that has you immersed your experience through every FPV flight, there is simply nothing like Cetus X FPV Kit. Wit

BetaFPV Cetus X FPV RTF Kit W/Betaflight FC, Goggles, & Controller

Whether you're a skillful pilot or a new beginner, the Cetus X FPV Kit is an advanced 2S power whoop bundle, and a primary choice to reach a higher stage. From its unparalleled control to its exciting flying that has you immersed your experience through every FPV flight, there is simply nothing like Cetus X FPV Kit. With the combination of Cetus X Brushless Quadcopter, LiteRadio 3 Radio Transmitter, and VR03 FPV Goggles, get ready for the next level of flying FPV.
Be sure to pick up some extra batteries so that you can fly all day! We recommend the following 1S batteries for this quad:

BetaFPV 1S 300mAh - BT2.0

Check out our other RTF combos, all our pre-built quads, and our BetaFPV selection!


Features

Nothing quite beats the experience of flying Cetus X with an enhanced propulsion system, and longer radio and video transmission. With a very functional and potential remote controller and FPV goggles, pilots can unlock more accomplishments to the next level.
Two FC versions are offered for pilots. With the support of the Betaflight configurator, beginners can learn quadcopter configuration through the Betaflight FC version. For pilots who prefer the classical Cetus, the Cetus FC version with an altitude hold function is also coming soon.
Classical white design inherited from Cetus Series and made of PA12 material, the Cetus X frame has an excellent impact resistance in drop &amp impact and reduces the risk of damage, giving you more peace of mind.
The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots.
LiteRadio 3 reserves a nano bay that supports the external TX module for the compatibility of more quadcopters. And the VR03 FPV goggles which are newly added a Micro SD card slot to save the video with DVR recording, support most Analog VTXs in the market.
The quadcopter, radio transmitter, FPV goggles, and all of the accessories are packed in an EVA portable storage bag. It is convenient to carry outside and better to protect the equipment.

Powerful Propulsion System
Equipped with 1103 11000KV Brushless Motors and Gemfan 2020 4-blade props, the Cetus X Brushless Quadcopter delivers powerful propulsion, making it a 2S power whoop drone with some real punch to it. The whole quadcopter is light and durable enough, offering pilots a high-efficiency flight experience.

Recording Every Flight Moment
Newly developed by BETAFPV, and based on VR02 FPV Goggles, the VR03 FPV Goggles take features of VR02 and come with a DVR recording function. Pilots can enjoy the playback saved through the goggles or export the videos by Micro SD card. This exciting function allows pilots to catch the memorably breathtaking moment, greatly heightening the FPV flying experience.

Improved Video Transmission
Cetus X Brushless Quadcopter comes with M04 25-400mW VTX and C04 FPV camera. M04 25-450mW VTX features a lightweight and adjustable output power for long-distance flying. Combining this VTX and the excellent radio link ExpressLRS 2.4G, pilots can fly whoop drones longer to explore more possibilities and have fun. In addition, the C04 FPV camera (based on Caddx Nano Ant Camera/Runcam Nano 4) shows better quality in FPV flight compared with the C02 FPV camera.

LiteRadio 3 Radio Transmitter
This transmitter features an ergonomically designed handle and has superb performance in its working time, a newly updated gimbal. Besides, this version supports BETAFPV Configurator, which is a utility designed to simply update, configure, and tune the radio controller. Experience the thrill of total immersion with unrivaled control and capture the world around you.

FPV Simulator Supported
First time flying a quadcopter? You can learn and practice flying a quadcopter through an FPV simulator before real flying. LiteRadio 1 supports playing FPV simulators like DRL/DCL/Uncrashed/Liftoff. LiteRadio 1 is capable of practicing and charging at the same time. Check out the Liftoff flying demonstration here. Download Liftoff here.

Various Modes, Accessible to All
Cetus X supports Angle/Horizon/Air Modes, which can satisfy the different needs of pilots and adapt to various flight environments. When the quadcopter falls to the ground and upside down, you can activate turtle mode by LiteRadio 3 transmitter to flip it over and resume flying. Whether you're a seasoned FPV pilot or a complete beginner, the Cetus X FPV Kit helps anyone fly confidently from day one.

BETAFPV Cetus Series
The BETAFPV Cetus Series has been very popular since its release in 2021 and become the primary FPV choice for new beginners. Whether propulsion system, radio transmitter, VTX range, or other functions, BETAFPV never stops step to make the product better. From the initial Cetus to Cetus X so far, Cetus Series always satisfies customers' needs no matter new beginners or seasoned pilots.

Specification

Item: Cetus X FPV Kit
Weight: 55g
Wheelbase: 95mm

FC: F4 2S 15A V1.0 (Betaflight FC Version)

Motors: 1103 11000KV Motor
Props: Gemfan 2020 4-Blades Props
Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4)
Camera Adjustable Angle: 0°-40°
Receiver Protocol: ELRS 2.4G (Betaflight)/Frsky D8 (Cetus)
VTX: M04 25-400mW VTX
Quadcopter: Cetus X Brushless Quadcopter
Transmitter: LiteRadio 3 Radio Transmitter
Goggles: VR03 FPV Goggles
Battery: 2x BT2.0 450mAh 1S 30C Battery
Flight time: 5 mins
Antennas: U.FL for Quad | RP-SMA for Goggles

Includes

1x Cetus X Brushless Quadcopter (Betaflight Firmware, ELRS 2.4G Receiver)
1x LiteRadio 3 Transmitter (ELRS 2.4G)
1x BETAFPV VR03 FPV Goggles 
4x BT2.0 450 mAh 1S Lipo Battery 
1x BT2.0 Battery Charger and Voltage Tester
1x USB Charging Cable (Type-C)
1x Type-C to FC Adapter
1x Prop Removal Tool
4x Gemfan 2020 4-Blades Prop (Spare Set)
1x Portable Storage Bag

FAQ

For more info and instructions, please check the User Manual for Cetus X FPV Kit.
Please DO NOT configure ESC or Motor settings on the Betaflight configurator.
The VR03 FPV goggles do not include a Micro SD card. You should prepare it before using the DVR recording function.
The External TX module for LiteRadio 3 should be bought separately. Recommend BETAFPV Nano TX Module.


Whether you're a skillful pilot or a new beginner, the Cetus X FPV Kit is an advanced 2S power whoop bundle, and a primary choice to reach a higher stage. From its unparalleled control to its exciting flying that has you immersed your experience through every FPV flight, there is simply nothing like Cetus X FPV Kit. Wi

BetaFPV RTF Cetus X FPV Analog Kit - Cetus Whoop, Goggles, Transmitter, Batteries, Charger & Case

BetaFPV RTF Cetus X FPV Analog Kit - Cetus Whoop, Goggles, Transmitter

Whether skillful pilots or new beginners, Cetus X FPV Kit, as the advanced 2S power whoop bundle, is a completely primary choice to reach a higher stage. From its unparalleled control to its exciting flying that has you immersed your experience through every FPV flight, there is simply nothing like Cetus X FPV Kit. With the combination of Cetus X Brushless Quadcopter, LiteRadio 3 Radio Transmitter, and VR03 FPV Goggles, get ready for the next level.
Recommend the newest BT2.0 550mAh 1S Battery. More flight time and higher discharge rate.

Bullet Point

Nothing quite beats the experience of flying Cetus X with an enhanced propulsion system, and longer radio and video transmission. With a very functional and potential remote controller and FPV goggles, pilots can unlock more accomplishments to the next level.
The Betaflight FC comes with the most popular firmware in the FPV community. Beginners are able to learn and understand more about FPV, which is an essential way to get drone experience.
The Cetus FC version offers an auxiliary flight function for pilots with three speed modes. It is easier and more suitable for initial pilots.
Classical white design inherited from Cetus Series and ade of PA12 material, the Cetus X frame has an excellent impact resistance in drop &amp impact and reduces the risk of damage, giving you more peace of mind.

The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots.
LiteRadio 3 reserves a nano bay that supports the external TX module for the compatibility of more quadcopters. And the VR03 FPV goggles which are newly added a Micro SD card slot to save the video with DVR recording, support most Analog VTXs in the market.
The quadcopter, radio transmitter, FPV goggles, and all of the accessories are packed in an EVA portable storage bag. It is convenient to carry outside and better to protect the equipment.

Specification

Item: Cetus X FPV Kit
Weight: 55g
Wheelbase: 95mm
FC*: F4 2S 15A V1.0 FC (Betaflight FC Version)/Cetus BL V3 FC (Cetus FC Version)

Motors: 1103 11000KV Motor

Props: Gemfan 2020 4-Blades Props

Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4)
Camera Adjustable Angle: 0°-40°
Receiver Protocol: ELRS 2.4G (Betaflight FC Version)/Frsky D8 (Cetus FC Version)

VTX: M04 25-400mW VTX (Betaflight FC Version)/Cetus 25-350mW VTX V2 (Cetus FC Version)
Quadcopter: Cetus X Brushless Quadcopter

Transmitter: LiteRadio 3 Radio Transmitter

Goggles: VR03 FPV Goggles

Battery*: BT2.0 450mAh 1S 75C Battery

Flight time: 5 mins

Note: FC (Betaflight FC Version) has been replaced from F4 1S 12A FC to F4 2S 15A V1.0 FC since Sep 2023. The battery will be upgraded from BT2.0 450mAh 1S 30C Battery to BT2.0 450mAh 1S 75C Battery from Feb 2024.

Cetus FC or Betaflight FC

Cetus X with the classical Cetus flight controller version is released. It supports the position hold function, which provides easier control to pilots. If select the Betaflight FC version, pilots are able to get and learn tons of FPV knowledge via the popular open source Betaflight flight controller community. Both FC versions perform great in power and speed and feature higher-grade control modes for pilots to get advanced.




Cetus FC Version
Betaflight FC Version



Flight Controller
Cetus BL V3 FC
F4 2S 15A V1.0 FC


Receiver Protocol
Frsky D8
ExpressLRS 2.4G


Flight Mode
N/S/M/Turtle Mode
Angle/Horizon/Air/Turtle Mode


VTX
25-350mW
25-400mW


Position Hold
Support
Not Support


Configuration Software

BETAFPV Configurator

Betaflight Configurator



Note: FC (Betaflight FC Version) has been replaced from F4 1S 12A FC to F4 2S 15A V1.0 FC since Sep 2023.

Auxiliary Flight Function
Built-in highly precise barometer to detect the height, the version with Cetus FC benefits from great stability due to its position hold mode, and auto-hovering, which enables the drone to stay at the current height. This function also ensures an emergency landing of the drone whenever loses control or is on low battery. Meanwhile, its stable flight allows you to catch the best footage with the VR03 FPV Goggles very well. It really does an immense amount of fun and ease of flight for all pilots.
Powered by 2S, Cetus X has loads of punch and speed, making it smoother and more suitable for outdoor practice, great for the next level. For indoor practice, the Cetus Pro with 1S power, which has the same auxiliary flight function, is easier for initial pilots to control and fly.

Note: The position hold function is only available in N mode.
Powerful Propulsion System

Equipped with 1103 11000KV Brushless Motor and Gemfan 2020 4-blade props, Cetus X Brushless Quadcopter delivers powerful propulsion, making it a 2S power whoop drone with some real punch to it. Besides, the whole quadcopter is light and durable enough, offering pilots a high-efficiency flight experience.

Recording Every Flight Moment

Newly developed by BETAFPV, and based on VR02 FPV Goggles, the VR03 FPV Goggles take features of VR02 and come with a DVR recording function. Pilots can enjoy the playback saved through the goggles or export the videos by Micro SD card. This exciting function allows pilots to catch the memorably breathtaking moment, greatly heightening the FPV flying experience.

Improved Video Transmission
Cetus X comes with M04 25-400mW VTX and C04 FPV camera. Both VTX features a lightweight and adjustable output power for longer distance flying. Combining this VTX and the excellent radio link ExpressLRS 2.4G, pilots can fly whoop drones longer to explore more possibilities and have fun. In addition, C04 FPV camera (based on Caddx Nano Ant Camera/Runcam Nano 4) shows better quality in FPV flight compared with C02 FPV camera.

LiteRadio 3 Radio Transmitter
This transmitter features an ergonomically designed handle and has superb performance in its working time, a newly updated gimbal. Besides, this version supports BETAFPV Configurator, which is a utility designed to simply update, configure, and tune the radio controller. Experience the thrill of total immersion with unrivaled control and capture the world around you.

FPV Simulator Supported
First time flying a quadcopter? You can learn and practice flying a quadcopter through an FPV simulator before real flying. LiteRadio 3 is available to play FPV simulators like DRL/DCL/Uncrashed/Liftoff. More convenient for practicing and charging at the same time. Here is the display of Liftoff. Download Liftoff here.

Note: This radio transmitter isn't compatible with Windows 11/Windows 10 systems running on AMD CPUs. If you wanna connect to a simulator, you will need to revert it to the ELRS 2.0 firmware.
Various Modes, Accessible to All

Cetus X (Betaflight FC) supports Angle/Horizon/Air Modes, which can satisfy the different needs of pilots and adapt to various flight environments. When the quadcopter falls to the ground and upside down, you can activate turtle mode by LiteRadio 3 transmitter to flip it over and resume flying. 

The version with Cetus FC has N/M/S three flight modes and supports 3 different speeds with SLOW/MID/FAST. Whether you're a seasoned FPV pilot or a complete beginner, the Cetus X FPV Kit helps anyone fly confidently from day one.

Note: The slow speed of Cetus FC version is not available on its M mode.
BETAFPV Cetus Series
BETAFPV Cetus Series has been very popular since its release in 2021 and become the primary FPV choice for new beginners. Whether propulsion system, radio transmitter, VTX range, or other functions, BETAFPV never stops step to make the product better. From the initial Cetus to Cetus X so far, Cetus Series always satisfies customers' needs no matter new beginners or seasoned pilots.


Recommended Parts


Frame: Cetus X Brushless Frame
Battery: BT2.0 450mAh 1S 30C Battery, BT2.0 550mAh 1S Battery
Props: Gemfan 2020 4-Blade Propellers
Camera: C04 Camera and VTX Module


FAQ


Top questions that customers frequently asked about Cetus X.


Download the User Manual for Cetus X FPV Kit (Betaflight F4 1S 12A FC version)


Download the User Manual for Cetus X FPV Kit (Betaflight F4 2S 15A V1.0 FC version)


Download the User Manual for Cetus X FPV Kit (Cetus FC version)

Download the CLI dump file for Cetus X (Betaflight F4 1S 12A FC version)


Download the CLI dump file for Cetus X (Betaflight F4 2S 15A V1.0 FC version)


Download the CLI dump file for Cetus X (Cetus FC version)
Please DO NOT configure ESC or Motor settings on the Betaflight configurator.

The VR03 FPV goggles do not include a Micro SD card. You should prepare it before using the DVR recording function.
The External TX module for LiteRadio 3 should be bought separately. Recommend BETAFPV Nano TX Module.

Package

1 * Cetus X Brushless Quadcopter (Betaflight FC or Cetus FC Version)
1 * LiteRadio 3 Transmitter (ELRS 2.4G or Frsky)
1 * BETAFPV VR03 FPV Goggles   
4 * BT2.0 450mAh 1S 75C Battery

1 * BT2.0 Battery Charger and Voltage Tester
1 * USB Charging Cable (Type-C)
1 * Type-C to FC Adapter
1 * Prop Removal Tool
4 * Gemfan 2020 4-Blades Prop (Spare Set)
2 * User Manual (Betaflight FC or Cetus FC Version)
1 * Portable Storage Bag






Cetus X FPV Kit

All batteries must be shipped by a ground shipping method. 
Whether you're a skillful pilot or a new beginner, the Cetus X FPV Kit is an advanced 2S power whoop bundle, and a primary choice to reach a higher stage. From its unparalleled control to its exciting flying that has you immersed your experience through every FPV flight, there is simply nothing like Cetus X FPV Kit. With the combination of Cetus X Brushless Quadcopter, LiteRadio 3 Radio Transmitter, and VR03 FPV Goggles, get ready for the next level of flying FPV.
Be sure to pick up some extra batteries so that you can fly all day! We recommend the following 1S batteries for this quad:

BetaFPV 1S 300mAh - BT2.0

Check out our other RTF combos, all our pre-built quads, and our BetaFPV selection!


Features

Nothing quite beats the experience of flying Cetus X with an enhanced propulsion system, and longer radio and video transmission. With a very functional and potential remote controller and FPV goggles, pilots can unlock more accomplishments to the next level.
Two FC versions are offered for pilots. With the support of the Betaflight configurator, beginners can learn quadcopter configuration through the Betaflight FC version. For pilots who prefer the classical Cetus, the Cetus FC version with an altitude hold function is also coming soon.
Classical white design inherited from Cetus Series and made of PA12 material, the Cetus X frame has an excellent impact resistance in drop &amp impact and reduces the risk of damage, giving you more peace of mind.
The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots.
LiteRadio 3 reserves a nano bay that supports the external TX module for the compatibility of more quadcopters. And the VR03 FPV goggles which are newly added a Micro SD card slot to save the video with DVR recording, support most Analog VTXs in the market.
The quadcopter, radio transmitter, FPV goggles, and all of the accessories are packed in an EVA portable storage bag. It is convenient to carry outside and better to protect the equipment.

Powerful Propulsion System
Equipped with 1103 11000KV Brushless Motors and Gemfan 2020 4-blade props, the Cetus X Brushless Quadcopter delivers powerful propulsion, making it a 2S power whoop drone with some real punch to it. The whole quadcopter is light and durable enough, offering pilots a high-efficiency flight experience.

Recording Every Flight Moment
Newly developed by BETAFPV, and based on VR02 FPV Goggles, the VR03 FPV Goggles take features of VR02 and come with a DVR recording function. Pilots can enjoy the playback saved through the goggles or export the videos by Micro SD card. This exciting function allows pilots to catch the memorably breathtaking moment, greatly heightening the FPV flying experience.

Improved Video Transmission
Cetus X Brushless Quadcopter comes with M04 25-400mW VTX and C04 FPV camera. M04 25-450mW VTX features a lightweight and adjustable output power for long-distance flying. Combining this VTX and the excellent radio link ExpressLRS 2.4G, pilots can fly whoop drones longer to explore more possibilities and have fun. In addition, the C04 FPV camera (based on Caddx Nano Ant Camera/Runcam Nano 4) shows better quality in FPV flight compared with the C02 FPV camera.

LiteRadio 3 Radio Transmitter
This transmitter features an ergonomically designed handle and has superb performance in its working time, a newly updated gimbal. Besides, this version supports BETAFPV Configurator, which is a utility designed to simply update, configure, and tune the radio controller. Experience the thrill of total immersion with unrivaled control and capture the world around you.

FPV Simulator Supported
First time flying a quadcopter? You can learn and practice flying a quadcopter through an FPV simulator before real flying. LiteRadio 1 supports playing FPV simulators like DRL/DCL/Uncrashed/Liftoff. LiteRadio 1 is capable of practicing and charging at the same time. Check out the Liftoff flying demonstration here. Download Liftoff here.

Various Modes, Accessible to All
Cetus X supports Angle/Horizon/Air Modes, which can satisfy the different needs of pilots and adapt to various flight environments. When the quadcopter falls to the ground and upside down, you can activate turtle mode by LiteRadio 3 transmitter to flip it over and resume flying. Whether you're a seasoned FPV pilot or a complete beginner, the Cetus X FPV Kit helps anyone fly confidently from day one.

BETAFPV Cetus Series
The BETAFPV Cetus Series has been very popular since its release in 2021 and become the primary FPV choice for new beginners. Whether propulsion system, radio transmitter, VTX range, or other functions, BETAFPV never stops step to make the product better. From the initial Cetus to Cetus X so far, Cetus Series always satisfies customers' needs no matter new beginners or seasoned pilots.

Specification

Item: Cetus X FPV Kit
Weight: 55g
Wheelbase: 95mm

FC: F4 2S 15A V1.0 (Betaflight FC Version)

Motors: 1103 11000KV Motor
Props: Gemfan 2020 4-Blades Props
Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4)
Camera Adjustable Angle: 0°-40°
Receiver Protocol: ELRS 2.4G (Betaflight)/Frsky D8 (Cetus)
VTX: M04 25-400mW VTX
Quadcopter: Cetus X Brushless Quadcopter
Transmitter: LiteRadio 3 Radio Transmitter
Goggles: VR03 FPV Goggles
Battery: 2x BT2.0 450mAh 1S 30C Battery
Flight time: 5 mins
Antennas: U.FL for Quad | RP-SMA for Goggles

Includes

1x Cetus X Brushless Quadcopter (Betaflight Firmware, ELRS 2.4G Receiver)
1x LiteRadio 3 Transmitter (ELRS 2.4G)
1x BETAFPV VR03 FPV Goggles 
4x BT2.0 450 mAh 1S Lipo Battery 
1x BT2.0 Battery Charger and Voltage Tester
1x USB Charging Cable (Type-C)
1x Type-C to FC Adapter
1x Prop Removal Tool
4x Gemfan 2020 4-Blades Prop (Spare Set)
1x Portable Storage Bag

FAQ

For more info and instructions, please check the User Manual for Cetus X FPV Kit.
Please DO NOT configure ESC or Motor settings on the Betaflight configurator.
The VR03 FPV goggles do not include a Micro SD card. You should prepare it before using the DVR recording function.
The External TX module for LiteRadio 3 should be bought separately. Recommend BETAFPV Nano TX Module.


All batteries must be shipped by a ground shipping method.  Whether you're a skillful pilot or a new beginner, the Cetus X FPV Kit is an advanced 2S power whoop bundle, and a primary choice to reach a higher stage. From its unparalleled control to its exciting flying that has you immersed your experience through every 

BetaFPV RTF Cetus X FPV Analog Kit - Cetus Whoop, Goggles, Transmitter, Batteries, Charger & Case from WREKD Co.

BetaFPV BNF Meteor75 Brushless Whoop

Stepping into HD world with 1S whoop quadcopter! The classical Meteor75 Brushless Whoop Quadcopter comes with Walksnail Avatar Mini HD VTX or HDZero Whoop Lite Bundle, bringing conspicuous images and exceptional visuals to your eyes and capturing details that make the footage look as exciting as the flight. Together wi

BetaFPV Meteor75 1S Walksnail Digital VTX Brushless Whoop Quadcopter - Choose Receiver

All products with batteries must be shipped by a ground shipping method.
Want a 1S whoop for outdoor, around the house and yard? The Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022), supporting serial ExpressLRS 2.4G, Frsky, or TBS RX for options. The new canopy with special style and high-quality C03 FPV camera combined with 0802SE 19500KV motors make it perfectly balanced in all areas of performance.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!

Features

The Meteor75 is the first generation whoop powered by a brand-new BT2.0 connector 450mAh battery. The BT2.0 connector effectively decreases internal connector resistance for a much better discharge performance compared with the initial PH2.0 connector.
The power system uses the latest 0802SE 19500KV motors and 40mm 2-blade props, which provides pilots a stronger experience of a powerful indoor and outdoor flight
Built-in 1.52g ultralight weight and upgraded C03 FPV camera. This new camera has optimal performance for indoor whoop drones.
Adopted with an injection molding technique, this canopy is 1.60g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
Reserved two UART ports on F4 1S 5A FC (SPI Frsky) board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it.
F4 1S 5A FC (Serial ELRS 2.4G) is flexible in upgrading and has great potential. It supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware.
The various colors of the spare parts including the 75mm frame and micro canopy, offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.

BETAFPV Meteor Series
This is the new Meteor75 Analog VTX version with a new micro canopy, built-in serial ExpressLRS 2.4G instead of SPI ERLS 2.4G, and the new C03 FPV camera that ensures a high-quality and clear image. For pilots who want to fly 1S HD whoop drone, Meteor75 HD digital VTX is a good choice.



 
Meteor75 (2022)
Meteor75 (2021)
Meteor75 1S HD


FC&ampESC
F4 1S 5A FC (2022)
F4 1S 5A FC
F4 1S 5A FC (2022)


RX
Serial ELRS, SPI FrSky/PNP, TBS
SPI ELRS, SPI FrSky, TBS
Serial ELRS, SPI FrSky/PNP, TBS


Camera
C03 FPV Camera
C02 FPV Camera
Walksnail/HDZero Camera


VTX
M03 Analog VTX
M03 Analog VTX
Walksnail Avatar or HD Zero Lite


Motors
0802SE 19500Kv Motor
1102 18000Kv or 0802SE 19500Kv Motors
1102 18000Kv Motors


Props
40mm 2-blade
40mm 3-blade, or 40mm 2-blade
40mm 3-blade


Canopy
New Micro Canopy (2022)
Micro Canopy
Micro Canopy for HD


Tilt
20° or 30°

30°

0-45°



Flight Time
6 mins (stable flying)
3-4 mins
3.5 mins (HDZero) or 3 mins (Walksnail)



 
BETAFPV upgraded all Meteor Series quadcopters like Meteor65, Meteor65 Pro, Meteor 75, and Meteor85 whoop quadcopters, through the new flight controller, motors, camera, frame, canopy, etc, to provide the best whoop quadcopters for pilots.
BT2.0 Connector
BETAFPV exclusive designed BT2.0 connector has broken through the bottle-neck of the PH2.0 connector. There is a graph comparing between BT2.0 connector 1S 450mAh battery and the Emax 1S 450mAh battery. The discharge current is 11A in this testing. You could see that it has a long time and improvement in voltage sag with a BT2.0 connector, which brings better flight performance.

Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP and can be switched to Futaba SFHSS protocol through Betaflight configurator. The ESC on the new board powered by BB51 hardware in place of BB21 comes with Bluejay 96k ESC firmware, allowing 0802SE 19500KV motors to give full play to the efficiency of power. We update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.



 
Meteor75 (ELRS)
Meteor75 (FrSky, PNP, TBS)


FC Inside
F4 1S 5A FC (Serial ELRS 2.4GHz)
F4 1S 5A FC (SPI FrSky)


Gyro
BMI270
BMI270


FC Firmware
BETAFPVF411
BETAFPVF411RX


UART Port
One UART Port
Two UART Port


External RX
Not Supported
Supported



 
Note: For F4 1S 5A FC (serial ELRS 2.4G), ONLY Betaflight firmware 4.3.0 and up start to support BMI270 gyro. For F4 1S 5A FC (SPI Frsky), we recommend using BETAFPVF411RX 4.2.11 firmware and CLI dump file offered by BETAFPV. If you update the 4.3.0 and up firmware for serial ELRS 2.4G from the Betaflight official site, please flash the CLI dump file for Meteor75.
Download the FC firmware and CLI dump file for Meteor 75 ELRS2.4G, Frsky, or TBS.

C03 Camera
C03 FPV Micro Camera is 1.52g ultralight weight and a great camera for indoor micro FPV quadcopters. It features a 1200TVL definition with 1/3" CMOS sensor, 2.1mm lens for 160° FOV, and excellent latency, which boasts high-quality, clear and sharper images through your goggles.

Motors
0802SE 19500KV Motor motor is a lightweight 1S motor, compared with the 0802 series brushless motors, it is not only significantly reduced the weight which is only 1.88g/pc but also ensures excellent performance of power and thrust. It makes the perfect dynamic balance, which gives the drone more flexibility and longer flying time.

Frame
This frame is ultralight only 5.68g and durable enough. The battery slot is closer to the center of gravity for a smoother flying experience, and you will land on the motor screws instead of the battery. BETAFPV offers various colors of Meteor75 frames for options, making DIY easier.

Specification

Item: Meteor75 Brushless Whoop Quadcopter (2022)
FC&ampESC: F4 1S 5A FC (Serial ELRS 2.4G)/F4 1S 5A FC (SPI Frsky)
Frame: Meteor75 Frame
Motors: 0802SE 19500KV Motor
Props: 40mm 2-Blade Propellers (1.0mm Shaft)
Camera: C03 FPV Camera
Tilt: 30° (default)/20° (optional)
Canopy: Canopy for Micro Camera 2022 version
Receiver Option: ELRS2.4G, Frsky/PNP, TBS Crossfire
VTX: M03 25-350mW VTX
Battery: BT2.0 450mAh 1S 30C Battery
Flight time: 6 mins (stable flying) / 4.5 mins (acro flying)
Weight: 24.98g

Includes

1x Meteor75 Brushless Whoop Quadcopter (1S)
2x 450mAh 1S 30C Battery with BT2.0 connector
1x BT2.0 Battery Charger and Voltage Tester
1x TypeC USB cable
1x Customized Carry Case
1x Spare 40mm 2-Blade props (1.0mm Shaft)
1x Screwdriver
3x Decorative Parts
1x 20° Lens Camera Mount for C03 Camera
1x 30° Lens Camera Mount for C02 Camera

FAQ

Download the FC firmware and CLI dump file for Meteor75.

ExpressLRS is the most popular radio link in 2021. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. Know more about the ExpressLRS project on Github or join the discussion in the Facebook Group.



All products with batteries must be shipped by a ground shipping method. Want a 1S whoop for outdoor, around the house and yard? The Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022), supporting serial ExpressLRS 2.4G, Frsky, or TBS R

BetaFPV BNF Meteor75 1S Brushless Analog Whoop (BT2.0) - ELRS 2.4 GHz

The classical Meteor75 Brushless Whoop Quadcopter comes with Walksnail Avatar Mini HD VTX bringing conspicuous images and exceptional visuals to your eyes and capturing details that make the footage look as exciting as the flight.

BetaFPV Meteor75 1S Brushless Whoop HD w/ Walksnail Avatar Mini VTX

The classical Meteor75 Brushless Whoop Quadcopter comes with HDZero Lite VTX bringing conspicuous images and exceptional visuals to your eyes and capturing details that make the footage look as exciting as the flight.

BetaFPV Meteor75 1S Brushless Whoop HD w/ HDZero 

All products with batteries must be shipped by a ground shipping method.
Want a 1S whoop for outdoor, around the house and yard? The Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022), supporting serial ExpressLRS 2.4G, Frsky, or TBS RX for options. The new canopy with special style and high-quality C03 FPV camera combined with 0802SE 19500KV motors make it perfectly balanced in all areas of performance.

Features

The Meteor75 is the first generation whoop powered by a brand-new BT2.0 connector 450mAh battery. The BT2.0 connector effectively decreases internal connector resistance for a much better discharge performance compared with the initial PH2.0 connector.
The power system uses the latest 0802SE 19500KV motors and 40mm 2-blade props, which provides pilots a stronger experience of a powerful indoor and outdoor flight
Built-in 1.52g ultralight weight and upgraded C03 FPV camera. This new camera has optimal performance for indoor whoop drones.
Adopted with an injection molding technique, this canopy is 1.60g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
Reserved two UART ports on F4 1S 5A FC (SPI Frsky) board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it.
F4 1S 5A FC (Serial ELRS 2.4G) is flexible in upgrading and has great potential. It supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware.
The various colors of the spare parts including the 75mm frame and micro canopy, offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.

BETAFPV Meteor Series
This is the new Meteor75 Analog VTX version with a new micro canopy, built-in serial ExpressLRS 2.4G instead of SPI ERLS 2.4G, and the new C03 FPV camera that ensures a high-quality and clear image. For pilots who want to fly 1S HD whoop drone, Meteor75 HD digital VTX is a good choice.



 
Meteor75 (2022)
Meteor75 (2021)
Meteor75 1S HD


FC&ampESC
F4 1S 5A FC (2022)
F4 1S 5A FC
F4 1S 5A FC (2022)


RX
Serial ELRS, SPI FrSky/PNP, TBS
SPI ELRS, SPI FrSky, TBS
Serial ELRS, SPI FrSky/PNP, TBS


Camera
C03 FPV Camera
C02 FPV Camera
Walksnail/HDZero Camera


VTX
M03 Analog VTX
M03 Analog VTX
Walksnail Avatar or HD Zero Lite


Motors
0802SE 19500Kv Motor
1102 18000Kv or 0802SE 19500Kv Motors
1102 18000Kv Motors


Props
40mm 2-blade
40mm 3-blade, or 40mm 2-blade
40mm 3-blade


Canopy
New Micro Canopy (2022)
Micro Canopy
Micro Canopy for HD


Tilt
20° or 30°

30°

0-45°



Flight Time
6 mins (stable flying)
3-4 mins
3.5 mins (HDZero) or 3 mins (Walksnail)



 
BETAFPV upgraded all Meteor Series quadcopters like Meteor65, Meteor65 Pro, Meteor 75, and Meteor85 whoop quadcopters, through the new flight controller, motors, camera, frame, canopy, etc, to provide the best whoop quadcopters for pilots.
BT2.0 Connector
BETAFPV exclusive designed BT2.0 connector has broken through the bottle-neck of the PH2.0 connector. There is a graph comparing between BT2.0 connector 1S 450mAh battery and the Emax 1S 450mAh battery. The discharge current is 11A in this testing. You could see that it has a long time and improvement in voltage sag with a BT2.0 connector, which brings better flight performance.

﻿Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP and can be switched to Futaba SFHSS protocol through Betaflight configurator. The ESC on the new board powered by BB51 hardware in place of BB21 comes with Bluejay 96k ESC firmware, allowing 0802SE 19500KV motors to give full play to the efficiency of power. We update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.



 
Meteor75 (ELRS)
Meteor75 (FrSky, PNP, TBS)


FC Inside
F4 1S 5A FC (Serial ELRS 2.4GHz)
F4 1S 5A FC (SPI FrSky)


Gyro
BMI270
BMI270


FC Firmware
BETAFPVF411
BETAFPVF411RX


UART Port
One UART Port
Two UART Port


External RX
Not Supported
Supported



﻿
Note: For F4 1S 5A FC (serial ELRS 2.4G), ONLY Betaflight firmware 4.3.0 and up start to support BMI270 gyro. For F4 1S 5A FC (SPI Frsky), we recommend using BETAFPVF411RX 4.2.11 firmware and CLI dump file offered by BETAFPV. If you update the 4.3.0 and up firmware for serial ELRS 2.4G from the Betaflight official site, please flash the CLI dump file for Meteor75.
Download the FC firmware and CLI dump file for Meteor 75 ELRS2.4G, Frsky, or TBS.

﻿C03 Camera
C03 FPV Micro Camera is 1.52g ultralight weight and a great camera for indoor micro FPV quadcopters. It features a 1200TVL definition with 1/3" CMOS sensor, 2.1mm lens for 160° FOV, and excellent latency, which boasts high-quality, clear and sharper images through your goggles.

Motors
0802SE 19500KV Motor motor is a lightweight 1S motor, compared with the 0802 series brushless motors, it is not only significantly reduced the weight which is only 1.88g/pc but also ensures excellent performance of power and thrust. It makes the perfect dynamic balance, which gives the drone more flexibility and longer flying time.

Frame
This frame is ultralight only 5.68g and durable enough. The battery slot is closer to the center of gravity for a smoother flying experience, and you will land on the motor screws instead of the battery. BETAFPV offers various colors of Meteor75 frames for options, making DIY easier.

Specification

Item: Meteor75 Brushless Whoop Quadcopter (2022)
FC&ampESC: F4 1S 5A FC (Serial ELRS 2.4G)/F4 1S 5A FC (SPI Frsky)
Frame: Meteor75 Frame
Motors: 0802SE 19500KV Motor
Props: 40mm 2-Blade Propellers (1.0mm Shaft)
Camera: C03 FPV Camera
Tilt: 30° (default)/20° (optional)
Canopy: Canopy for Micro Camera 2022 version
Receiver Option: ELRS2.4G, Frsky/PNP, TBS Crossfire
VTX: M03 25-350mW VTX
Battery: BT2.0 450mAh 1S 30C Battery
Flight time: 6 mins (stable flying) / 4.5 mins (acro flying)
Weight: 24.98g

Includes

1x Meteor75 Brushless Whoop Quadcopter (1S)
2x 450mAh 1S 30C Battery with BT2.0 connector
1x BT2.0 Battery Charger and Voltage Tester
1x TypeC USB cable
1x Customized Carry Case
1x Spare 40mm 2-Blade props (1.0mm Shaft)
1x Screwdriver
3x Decorative Parts
1x 20° Lens Camera Mount for C03 Camera
1x 30° Lens Camera Mount for C02 Camera

FAQ

Download the FC firmware and CLI dump file for Meteor75.

ExpressLRS is the most popular radio link in 2021. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. Know more about the ExpressLRS project on Github or join the discussion in the Facebook Group.



All products containing batteries must be shipped by a ground shipping method.
Want a 1S whoop for outdoor, around the house and the yard? Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022). The canopy has a special design and high-quality C03 FPV camera combined with 0802SE 19500KV motors make it perfectly balanced in all areas of performance.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!
Features

Meteor75 is the first generation whoop powered by a brand-new BT2.0 connector 450mAh battery. The BT2.0 connector effectively decreases internal connector resistance for a much better discharge performance compared with the initial PH2.0 connector
The power system uses the latest 0802SE 19500KV motors and 40mm 2-blade props, which provides pilots a powerful indoor and outdoor flight.
Built-in 1.45g ultralight weight and upgraded C03 FPV camera. This new camera has optimal performance for indoor whoop drones.
Adopt with injection molding technique, this canopy is 1.60g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
Reserve two UART ports on F4 1S 5A FC (SPI Frsky) board.
The various colors of the spare parts including the 75mm frame and micro canopy, offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.


BT2.0 Connector
BETAFPV has exclusively designed BT2.0 connector has broken through the bottle-neck of PH2.0 connector. There is a graph of comparison between BT2.0 connector 1S 450mAh battery and Emax 1S 450mAh battery. The discharge current is 11A in this testing. You could see that it has a longer time and improvement in voltage sag with BT2.0 connector, which brings better flight performance.

Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP and can be switched to Futaba SFHSS protocol through Betaflight configurator. The ESC on the new board powered by BB51 hardware in place of BB21 comes with Bluejay 96k ESC firmware, allowing 0802SE 19500KV motors to give full play to the efficiency of power. We update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.
Meteor75: (Frsky)
FC Inside:F4 1S 5A FC (SPI Frsky)Gyro: BMI270FC Firmware: BETAFPVF411RXUART Port: Two UART PortsExternal RX: Supported
C03 Camera
C03 FPV Micro Camera is 1.45g ultralight weight and a great camera for indoor micro FPV quadcopters. It features a 1200TVL definition with 1/3" CMOS sensor, 2.1mm lens for 160° FOV, and excellent latency, which boasts high-quality, clear and sharper images through your goggles.

Motors
0802SE 19500KV Motor motor is a lightweight 1S motor, compared with the 0802 series brushless motors, it is not only significantly reduced the weight to only 1.88g/pc but ensures excellent performance of power and thrust. It makes the perfect dynamic balance, which gives the drone more flexibility and longer flying time.
 

Frame
This frame is ultralight at only 5.68g and still durable. The battery slot is closer to the center of gravity for a smoother flying experience, and you will land on the motor screws instead of the battery. BETAFPV offers various colors of Meteor75 frames for options, making DIY easier.

Specifications

Item: Meteor75 Brushless Whoop Quadcopter (2022)
FC&ampESC:F4 1S 5A FC (SPI Frsky)
Frame: Meteor75 Frame
Motors: 0802SE Brushless Motor
Props: 40mm 2-Blade Propellers (1.0mm Shaft)
Camera: C03 FPV Camera
Tilt: 30° (default)/20° (optional)
Canopy: Canopy for Micro Camera 2022 version
Receiver Option: Frsky
VTX: M03 25-350mW VTX
Battery: BT2.0 450mAh 1S 30C Battery
Flight time: 6 mins (stable flying) / 4.5 mins (acro flying)
Weight: 24.98g

Includes

1x BetaFPV Meteor75 Whoop Quadcopter (2022) - FRSKY
2x 450mAh 1S 30C Battery with BT2.0 connector
1x BT2.0 Battery Charger and Voltage Tester
1x TypeC USB cable
1x Customized Carry Case
1x Spare 40mm 2-Blade props (1.0mm Shaft)
1x Screwdriver
3x Decorative Parts
1x 20° Lens Camera Mount for C03 Camera
1x 30° Lens Camera Mount for C02 Camera
1x Pack of Screws



All products containing batteries must be shipped by a ground shipping method. Want a 1S whoop for outdoor, around the house and the yard? Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022). The canopy has a special design and high-qua

BetaFPV BNF Meteor75 1S Analog Whoop (2022) - FRSKY

BetaFPV BNF Meteor75 1S Analog Whoop (2022) - FRSKY from WREKD Co.

Want a 1S whoop for outdoor, around the house and yard? The Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022), supporting serial ExpressLRS 2.4G, Frsky, or TBS RX for options. The new canopy with special style and high-quality C03 FPV camera combined with 0802SE 19500KV motors make it perfectly balanced in all areas of performance.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!

Features

The Meteor75 is the first generation whoop powered by a brand-new BT2.0 connector 450mAh battery. The BT2.0 connector effectively decreases internal connector resistance for a much better discharge performance compared with the initial PH2.0 connector.
The power system uses the latest 0802SE 19500KV motors and 40mm 2-blade props, which provides pilots a stronger experience of a powerful indoor and outdoor flight
Built-in 1.52g ultralight weight and upgraded C03 FPV camera. This new camera has optimal performance for indoor whoop drones.
Adopted with an injection molding technique, this canopy is 1.60g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
Reserved two UART ports on F4 1S 5A FC (SPI Frsky) board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it.
F4 1S 5A FC (Serial ELRS 2.4G) is flexible in upgrading and has great potential. It supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware.
The various colors of the spare parts including the 75mm frame and micro canopy, offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.

BETAFPV Meteor Series
This is the new Meteor75 Analog VTX version with a new micro canopy, built-in serial ExpressLRS 2.4G instead of SPI ERLS 2.4G, and the new C03 FPV camera that ensures a high-quality and clear image. For pilots who want to fly 1S HD whoop drone, Meteor75 HD digital VTX is a good choice.



 
Meteor75 (2022)
Meteor75 (2021)
Meteor75 1S HD


FC&ampESC
F4 1S 5A FC (2022)
F4 1S 5A FC
F4 1S 5A FC (2022)


RX
Serial ELRS, SPI FrSky/PNP, TBS
SPI ELRS, SPI FrSky, TBS
Serial ELRS, SPI FrSky/PNP, TBS


Camera
C03 FPV Camera
C02 FPV Camera
Walksnail/HDZero Camera


VTX
M03 Analog VTX
M03 Analog VTX
Walksnail Avatar or HD Zero Lite


Motors
0802SE 19500Kv Motor
1102 18000Kv or 0802SE 19500Kv Motors
1102 18000Kv Motors


Props
40mm 2-blade
40mm 3-blade, or 40mm 2-blade
40mm 3-blade


Canopy
New Micro Canopy (2022)
Micro Canopy
Micro Canopy for HD


Tilt
20° or 30°

30°

0-45°



Flight Time
6 mins (stable flying)
3-4 mins
3.5 mins (HDZero) or 3 mins (Walksnail)



 
BETAFPV upgraded all Meteor Series quadcopters like Meteor65, Meteor65 Pro, Meteor 75, and Meteor85 whoop quadcopters, through the new flight controller, motors, camera, frame, canopy, etc, to provide the best whoop quadcopters for pilots.
BT2.0 Connector
BETAFPV exclusive designed BT2.0 connector has broken through the bottle-neck of the PH2.0 connector. There is a graph comparing between BT2.0 connector 1S 450mAh battery and the Emax 1S 450mAh battery. The discharge current is 11A in this testing. You could see that it has a long time and improvement in voltage sag with a BT2.0 connector, which brings better flight performance.

﻿Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP and can be switched to Futaba SFHSS protocol through Betaflight configurator. The ESC on the new board powered by BB51 hardware in place of BB21 comes with Bluejay 96k ESC firmware, allowing 0802SE 19500KV motors to give full play to the efficiency of power. We update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.



 
Meteor75 (ELRS)
Meteor75 (FrSky, PNP, TBS)


FC Inside
F4 1S 5A FC (Serial ELRS 2.4GHz)
F4 1S 5A FC (SPI FrSky)


Gyro
BMI270
BMI270


FC Firmware
BETAFPVF411
BETAFPVF411RX


UART Port
One UART Port
Two UART Port


External RX
Not Supported
Supported



﻿
Note: For F4 1S 5A FC (serial ELRS 2.4G), ONLY Betaflight firmware 4.3.0 and up start to support BMI270 gyro. For F4 1S 5A FC (SPI Frsky), we recommend using BETAFPVF411RX 4.2.11 firmware and CLI dump file offered by BETAFPV. If you update the 4.3.0 and up firmware for serial ELRS 2.4G from the Betaflight official site, please flash the CLI dump file for Meteor75.
Download the FC firmware and CLI dump file for Meteor 75 ELRS2.4G, Frsky, or TBS.

﻿C03 Camera
C03 FPV Micro Camera is 1.52g ultralight weight and a great camera for indoor micro FPV quadcopters. It features a 1200TVL definition with 1/3" CMOS sensor, 2.1mm lens for 160° FOV, and excellent latency, which boasts high-quality, clear and sharper images through your goggles.

Motors
0802SE 19500KV Motor motor is a lightweight 1S motor, compared with the 0802 series brushless motors, it is not only significantly reduced the weight which is only 1.88g/pc but also ensures excellent performance of power and thrust. It makes the perfect dynamic balance, which gives the drone more flexibility and longer flying time.

Frame
This frame is ultralight only 5.68g and durable enough. The battery slot is closer to the center of gravity for a smoother flying experience, and you will land on the motor screws instead of the battery. BETAFPV offers various colors of Meteor75 frames for options, making DIY easier.

Specification

Item: Meteor75 Brushless Whoop Quadcopter (2022)
FC&ampESC: F4 1S 5A FC (Serial ELRS 2.4G)/F4 1S 5A FC (SPI Frsky)
Frame: Meteor75 Frame
Motors: 0802SE 19500KV Motor
Props: 40mm 2-Blade Propellers (1.0mm Shaft)
Camera: C03 FPV Camera
Tilt: 30° (default)/20° (optional)
Canopy: Canopy for Micro Camera 2022 version
Receiver Option: ELRS2.4G, Frsky/PNP, TBS Crossfire
VTX: M03 25-350mW VTX
Battery: BT2.0 450mAh 1S 30C Battery
Flight time: 6 mins (stable flying) / 4.5 mins (acro flying)
Weight: 24.98g

Includes

1x Meteor75 Brushless Whoop Quadcopter (1S)
2x 450mAh 1S 30C Battery with BT2.0 connector
1x BT2.0 Battery Charger and Voltage Tester
1x TypeC USB cable
1x Customized Carry Case
1x Spare 40mm 2-Blade props (1.0mm Shaft)
1x Screwdriver
3x Decorative Parts
1x 20° Lens Camera Mount for C03 Camera
1x 30° Lens Camera Mount for C02 Camera

FAQ

Download the FC firmware and CLI dump file for Meteor75.

ExpressLRS is the most popular radio link in 2021. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. Know more about the ExpressLRS project on Github or join the discussion in the Facebook Group.



Want a 1S whoop for outdoor, around the house and yard? The Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022), supporting serial ExpressLRS 2.4G, Frsky, or TBS RX for options. The new canopy with special style and high-quality C03 FPV

BetaFPV BNF Meteor75 1S Brushless Analog Whoop (BT2.0) - ELRS 2.4 GHz from WREKD Co.


Stepping into HD world with 1S whoop quadcopter! The classical Meteor75 Brushless Whoop Quadcopter comes with Walksnail Avatar Mini HD VTX or HDZero Whoop Lite Bundle, bringing conspicuous images and exceptional visuals to your eyes and capturing details that make the footage look as exciting as the flight. Together with 1102 18000KV motors that feature strong propulsion, it gives pilots powerful and impressive results. Enjoy an immersive flight experience, and get the perfect shots with the new HD VTX system indoors and outdoors.

Tons of ExpressLRS items are available now!
Recommend the newest BT2.0 550mAh 1S Battery. More flight time and higher discharge rate.

Bullet Points

Powerful propulsion capabilities combined with Walksnail HD VTX or HDZero VTX give pilots an immersive flight experience and impactful visuals.
Ultralight weight for 40.5g (Walksnail)/ 36.4g (HDZero). With BT2.0 connector, it effectively decreases internal connector resistance for good conductive performance.

Equipped with 40mm 3-blade props and upgraded 1102 18000KV motors. The upgraded motors not only take abilities as good as before to provide strong propulsion in 1S whoop drone but also come with a new look. And simultaneously its black and red motor bell fully matches the Meteror75 frame.

Reserve two UART ports on F4 1S 5A FC(SPI Frsky) V3.0 board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it.
F4 1S 5A FC (Serial ELRS 2.4G) V2.0 is flexible in upgrading and has great potential. It supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware.


Specification

Item: Meteor75 Brushless Whoop Quadcopter (1S HD Digital VTX)
Flight Time: 3.5 mins (HDZero)/3 mins (Walksnail)
Camera Adjustable Angle: 0-45°
Motors: 1102 18000KV Motor

Battery: BT2.0 450mAh 1S 30C Battery

Frame: Meteor75 Micro Brushless Whoop Frame

Propellers: 40mm 3-Blade Propellers (1.5mm Shaft)

Weight Without Battery: 40.5g (Walksnail)/36.4g (HDZero)
Receiver: Serial ELRS 2.4G/SPI Frsky/TBS
FC&ampESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0
VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero)
VTX: 1S Walksnail Avatar Mini HD VTX/HDZero Whoop Lite Bundle
Camera: Wanlksnail Avatar Nano Camera/HDZero Nano Lite Camera


Note: F4 1S 5A FC (Serial ELRS 2.4G) V2.0 does not support external receivers. F4 1S 5A FC (SPI Frsky) V3.0 is available to connect an external receiver and can be used as PNP. Please make sure that the battery voltage must be 3V at least when flying, otherwise, the HD digital VTX would stop working. 
HD Digital VTX System
There are two HD versions to choose from. Based on Walksnail Avatar, the Walksnail Avatar Mini HD VTX also uses H.265 high-efficiency video coding, an industry-leading technology, providing 1080P/60FPS image recording with 22ms ultra-low latency. It is specially designed for 3.1-5V power input and 10g lightweight, which is compatible with 1S whoop drone. Build-in 8 GB storage, the Avatar Mini HD VTX has the capability of recording HD video without interference from capacity and exporting video by USB cable. Besides, with Canvas Mode on Avatar Mini HD VTX, Betaflight full OSD display is supported and can be adjusted easily by remote control.

HDZero Nano Lite Camera is designed for feather-lite drones where every gram counts. At a weight as low as 1.5g, combined with the new Whoop Lite VTX at 4.5g with 0.4g dipole antenna enables a world’s-first production digital FPV solution of about 7g. The HDZero Whoop lite Bundle supports 1-3S power input with 25mW/200mW RF power and is capable of recording in 720P/60FPS with super low latency of less than 19ms. What's more, pilots can activate and configure its OSD function on Betaflight Configurator.

Injection Molded Canopy for HD Camera
Micro Canopy for HD Camera is specially designed to be compatible with Walksnail or HDZero HD digital VTX and has an adjustable camera lens of 0-45°. With the injection molding technique, the canopy is very durable and flexible for crash resistant. Besides, the hollow-out design not only reduces the influence of heat on electronic parts but also is available to be armed with decorative parts we prepared.

New 1102 18000KV Motors
1102 18000KV motors have a great balance between weight and power on 75mm 1S whoop drones. Only 2.9g with connectors. With the high 18000KV, it could have a great punch power even with only 1S battery. Also, it adopts a PCB connector to allow you to repair it easier once cables are disconnected.

Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75 HD. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. The ESC on the new board is powered by BB51 hardware in place of BB21. Last but not least, we update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.





Meteor75 HD (ELRS)

Meteor75 HD (Frsky, PNP, TBS)


FC Inside
F4 1S 5A FC (Serial ELRS 2.4G) V2.0
F4 1S 5A FC (SPI Frsky) V3.0


Gyro
BMI270
BMI270


FC Firmware
BETAFPVF411
BETAFPVF411RX


UART Port
One UART Port
Two UART Ports


External RX
Not Supported
Supported



Note: Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware and CLI dump file. If you update the 4.3.1 firmware from Betaflight official site, please flash the CLI dump file for Meteor75 HD.
Download the FC firmware and CLI dump file for Walksnail and HDZero version.
Recommended Parts

Radio Transmitter: LiteRadio 3 Pro, LiteRadio 3, LiteRadio 2 SE
Battery: BT2.0 450mAh 1S 30C Battery, BT2.0 550mAh 1S Battery
Props: 40mm 3-Blade Propellers (1.5mm Shaft)
Colorful Frame: Meteor75 Micro Brushless Whoop Frame

Colorful Canopy: Micro Canopy for HD Camera

Sticker: BETAFPV Waterslide Decals

Charger: 6 Ports 1S Battery Charger &amp Adapter

Screws: Meteor Series Motor Fixing Screws Pack (40PCS)

BT2.0 Series Accessories

FAQ

Pilots can read and export the recording videos from Walksnail VTX by a 4-pin connector. Below is the diagram picture. For more information, please refer to the manual for it.



Click to download the manual for Walksnail Avatar Mini VTX.
Click to download the manual for HDZero Whoop Lite Bundle.

Package

1 * Meteor75 Brushless Whoop Quadcopter (Walksnail or HDZero HD Digital VTX)
2 * 450mAh 1S 30C Battery with BT2.0 Connector
1 * Type-C USB Cable
1 * BT2.0 Battery Charger and Voltage Tester
4 * 40mm 3-Blade Props (1.5mm Shaft)
1 * Screwdriver
1 * Walksnail VTX USB Cable (For Walksnail Version)
1 * HDZero VTX USB Cable (For HDZero Version)
1 * Pack of Screws

Note: The propellers in the package were modified from three holes to one hole.



Meteor75 Brushless Whoop Quadcopter (1S HD Digital VTX)

Meteor75, a better approach to the 75mm micro drone which features high KV motors - 1102 18000KV motors & BT2.0 450mAH battery, giving pilots plenty of power to use both indoor and outdoor spaces as a small scale acro playground.

BetaFPV Meteor75 1S Brushless Whoop Quadcopter

Sub250

Sub250 BNF Nanofly16 1S 40mm Quad

We are very happy to introduce our first Ultra-light Freestyle FPV Drone Sub250 1s Nanofly16 to you. it is very quiet, and suitable for both indoors and outdoors. Currently available in 2 versions: ELRS 2.4G, TBSNanoRX-TBS 915 Mhz. The design concept of Nanofly16 quad is lightweight, small in size, has good hand feels,

Sub250 Nanofly16 1S 1.6'' Analog Micro BNF Freestyle Quadcopter - Choose Receiver

Happymodel

Happymodel BNF Mobula 7 Whoop

We’re glad to launched our new Mobula7 drone , this time the 75mm whoop based on 1s power. Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1s Will be the best choice in the whoop season. The world first 5-IN-1 AIO flight controller with ExpressLRS 2.0 , OPENV

Happymodel Mobula7 1s 75mm Analog FPV Brushless Whoop Drone - Choose Receiver

This&nbspHappymodel Mobula7&nbspis a 1S micro whoop with a RunCam Nano 3 Camera. This whoop features the first 5-in-1 AIO with three different receiver options and 0802 20000KV motors with a unibell design.

This Happymodel Mobula7 is a 1S micro whoop with a RunCam Nano 3 Camera. This whoop features the first 5-in-1 AIO with three different receiver options and 0802 20000KV motors with a unibell design.

Happymodel Mobula7 1S 75mm Analog Whoop

HAPPYMODEL

Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1S Will be the best choice in the whoop season.  This is an amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX ranges by using this flight controller. The new RS0802 motors come with a new unibell design, uses a 1.5mm shaft, and includes a PCB bottom plate, which means high efficiency, and much more reliability.
Check out the rest of pre-built quads and our HappyModel selection!
Due to Runcam Nano3 camera was discontinued, now the Mobula7 1s comes with Caddx ant camera since May 2024. The Mobula7 1s with Caddx ant camera we called V2 version.
Features

We’re glad to launched our new Mobula7 drone , this time the 75mm whoop based on 1s power. Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1s Will be the best choice in the whoop season.
The world first 5-IN-1 AIO flight controller with ExpressLRS 2.0 , OPENVTX(up to 400mw), 12A Brushless Blheli_S ESC and Betaflight OSD coming out recently. This is amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX range by using this flight controller.
The new RS0802 motors comes with a new unibell design, use 1.5mm shaft and include PCB bottom plate, high efficiency and much more reliable.
New onboard OpenVTX , max power up to 400mw, provide RCE and PIT mode, it was very useful for race event.

X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V2.0 and Openvtx

VTX Power up to 400mw

ELRS V2.0 Support

NEW RS0802 KV20000 motors

Caddxfpv ANT 1/3 CMOS 1200TVL Camera

Smooth and powerful

Compatible for 1S Lipo/LIHV

Recommend 1S 450mah/550mah/650mah battery(Not include)

Specifications

Item Name: HappyModel BNF 1S Mobula7 Analog Whoop - Choose Receiver Type
Wheelbase: 75mm

Size: 99mm x 99mm x 40mm

Weight: 24g
Receiver option:-2.4G ELRS SPI-SPI Frsky D8/D16  not compatible with EMAX E6 radio-TBS version(with external TBS CRSF NANO RX)

Motor

Mode: RS0802 KV20000

Configu-ration:9N12P

Stator Diamter:8mm

Stator Length:2mm

Shaft Diameter:Φ1.5mm

Motor Dimension(Dia.xLen):Φ10.5mm x 13.5mm

Weight(g):2.0g

No.of Cells(Lipo):1S only

Propellers

Weight:0.24g

Material:PC

Pitch:1 inchProps Dia:40mm

Center Thickness:5mm

Center Hole Dia:1.5mm

Flight Controller

X12 ELRS V1.0 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280

X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR

X12 PNP V1.0 flight controller with external TBS CRSF Nano receiver Target: CRAZYBEEF4DX

X12 PNP V1.0 flight controller without onboard receiver Target: CRAZYBEEF4DX

MCU:STM32F411CEU6 (100MHZ, 512K FLASH)

Sensor: MPU6000 or ICM20689 or BMI270(SPI connection)

Mount hole size: 25.5mm x 25.5mm

Power supply: 1S battery input (DC 2.9V-4.35V)

Built-in 12A(each) Blheli_S 4in1 ESC

Built-in Betaflight OSD(SPI Control)

Built-in 5.8G OpenVTX 0mw~400mw

Built-in ExpressLRS 2.4G,Frsky D8/D16

Built-in voltage detection

Built-in current sensor

Onboard 4in1 ESC

Power supply: 1S LiPo/LiPo HV

Current: 12A continuous peak 15A (3 seconds)

Support BLHeliSuite programmable

Factory firmware: Z_H_30_REV16_7.HEX

Default protocol: DSHOT300

Support Bluejay firmware

When use Blujay firmware with 48khz, should set startup power to 1100/1200

Receiver 

ExpressLRS 2.4GHz

Packet Rate option: 50Hz/150Hz/250Hz/500Hz

ExpressLRS Firmware version: V2.0

RF Frequency: 2.4GHz

Antenna : SMD antenna

Telemetry output Power: &lt12dBm

Receiver protocol:  SPI ExpressLRS

Compatible with ExpressLRS V2.0 TX Module

Couldn’t flash separately ExpressLRS firmware


Frsky SPI D8/D16

SPI BUS receiver Frsky D8 compatible

Compatible Non EU transmitter D8 modelChannels: 8ch

No ground interference ( Transmitter and receiver 1 m from the ground): 200meterFailsafe support


Onboard 5.8 OPENVTX

Firmware version: OPENVTX

Smartaudio v2.1

PIT Mode support

RCE Mode support

Channels:48ch

Transmitting Power: 0/RCE/25mw/100mw/400mw

Power supply: DC 5V

Current (5v):650ma~1000ma


CaddxFPV ANT Camera

Image Sensor: 1/3″ CMOS Sensor

Horizontal Resolution: 1200 TVL

TV System: NTSC or PAL

IMAGE: 16:9 or 4:3

Synchronization: Internal

Electronic Shutter: PAL: 1/50~100,000 NTSC: 1/60~100,000

S/N Ratio : &gt52dB (AGC OFF)

Video Output: CVBS

Lens: 1.8mm

Min. Illumination: 0.001Lux@F1.2

Auto Gain Control: YES

WDR: Global WDR

DNR: 3D DNR

Dimensions: 14x14mm(with bracket to 19x19mm)

Wide Power Input: DC 3.7-18V

Weight: 2g (N.W.)



Includes

1x HappyModel BNF 1S Mobula 7 Whoop



The all-new HappyModel BNF 1S Mobula 7 Whoop features the latest parts to bring you a fun, exciting whoop to fly. Get it shipped fast and free from RDQ!

HappyModel BNF 1S Mobula7 Analog Whoop - Choose Receiver Type

HappyModel BNF 1S Mobula 7 Whoop for Sale - RaceDayQuads

Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1S Will be the best choice in the whoop season.  This is an amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX ranges by using this flight controller. The new RS0802 motors come with a new unibell design, uses a 1.5mm shaft, and includes a PCB bottom plate, which means high efficiency, and much more reliability.
Check out the rest of pre-built quads and our HappyModel selection!
Features

X12 5-IN-1 AIO flight controller w/ built-in receiver and OpenVTX
VTX Power up to 400mw
RS0802 20000KV motors
RunCam Nano 3. The lightest 1/3 CMOS 800TVL Camera
Smooth and powerful
Compatible with 1S Lipo/LIHV

Specifications

Input Voltage: 1S
Max Continuous Current: 12A
Motors: 0802 20000KV
Camera: RunCam Nano 3
Wheelbase: 75mm
Dimensions: 99x99x40mm
Weight: 24g

Includes

1x HappyModel BNF 1S Mobula 7 Whoop



Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1S Will be the best choice in the whoop season.  This is an amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX ranges by using this flight controller. The new RS0802 motors come

HappyModel BNF 1S Mobula7 Analog Whoop - Choose Receiver Type from WREKD Co.

BetaFPV BNF Cetus X Brushless Whoop

All batteries must be shipped by a ground shipping method.
Cetus X Brushless Quadcopter is a 2S power whoop drone and a primary choice for beginners who want to get advanced flight skills. It features a stronger propulsion system for a speedier and more violent flight, which is capable of performing diverse freestyle tricks. Equipped with M04 400mW VTX and C04 FPV camera that is optimized for longer radio and video transmission. Meanwhile, it supports the Betaflight configurator which is a popular application to configure RC aircraft.
Check out our other RTF combos, all our pre-built quads and our BetaFPV selection!

Features

An excellent preference for beginners to get advanced level. Cetus X brushless Quadcopter is proud of its lightning speed with rapid startup due to its stronger propulsion system.
Build-in ExpressLRS 2.4G receiver that is the most popular radio link, low latency, and far controlling range are possible. Pilots can not only enjoy the flight indoors but also explore the scenery outdoor.

Featuring M04 400mW VTX, C04 FPV camera (based on Caddx Nano Ant Camera or Runcam Nano 4), and 2xBT2.0 450mAh 1S 30C battery for longer radio and video transmission and flight endurance, Cetus X brushless quadcopter allows beginners to gain more achievements in FPV flight.

Classical white design inherited from Cetus Series and made of PA12 material, Cetus X frame has an excellent impact resistance in drop &amp impact. The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots.

Specifications

Item: Cetus X Brushless Quadcopter
Weight: 55g
Wheelbase: 95mm
FC*: F4 2S 15A V1.0 (Betaflight FC Version)

Motors: 1103 11000KV Motor

Props: Gemfan 2020 4-Blades Props
Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4)
Camera Adjustable Angle: 0°-40°
Receiver Protocol: ELRS 2.4G
VTX: M04 25-400mW VTX
Battery: 2*BT2.0 450mAh 1S 30C Battery
Flight time: 5 mins



Downloads
FC Firmware and ESC download
 
Includes


1 x Cetus X Brushless Quadcopter
1 x BT2.0 Battery Charger and Voltage Tester
2 x BT2.0 450mAh 1S 30C Battery
1 x Phillips Screwdriver
1 x Prop Removal Tool
1 x Type-C Adapter
4 x Gemfan 2020 4-Blades Props

 


All batteries must be shipped by a ground shipping method. Cetus X Brushless Quadcopter is a 2S power whoop drone and a primary choice for beginners who want to get advanced flight skills. It features a stronger propulsion system for a speedier and more violent flight, which is capable of performing diverse freestyle t

BetaFPV BNF Cetus X Brushless Analog Whoop - ELRS 2.4G from WREKD Co.

BetaFPV BNF Cetus X Brushless Analog Whoop - ELRS 2.4G

All batteries must be shipped by a ground shipping method.
Cetus X Brushless Quadcopter is a 2S power whoop drone and a primary choice for beginners who want to get advanced flight skills. It features a stronger propulsion system for a speedier and more violent flight, which is capable of performing diverse freestyle tricks. Equipped with M04 400mW VTX and C04 FPV camera that is optimized for longer radio and video transmission. Meanwhile, it supports the Betaflight configurator which is a popular application to configure RC aircraft.
 
Features

An excellent preference for beginners to get advanced level. Cetus X brushless Quadcopter is proud of its lightning speed with rapid startup due to its stronger propulsion system.
Build-in ExpressLRS 2.4G receiver that is the most popular radio link, low latency, and far controlling range are possible. Pilots can not only enjoy the flight indoors but also explore the scenery outdoor.

Featuring M04 400mW VTX, C04 FPV camera (based on Caddx Nano Ant Camera or Runcam Nano 4), and 2xBT2.0 450mAh 1S 30C battery for longer radio and video transmission and flight endurance, Cetus X brushless quadcopter allows beginners to gain more achievements in FPV flight.

Classical white design inherited from Cetus Series and made of PA12 material, Cetus X frame has an excellent impact resistance in drop &amp impact. The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots.

Specifications

Item: Cetus X Brushless Quadcopter
Weight: 55g
Wheelbase: 95mm
FC: F4 1S 12A FC V2.2 (ELRS 2.4G)
Motors: 1103 11000KV Motor
Props: Gemfan 2020 4-Blades Props
Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4)
Camera Adjustable Angle: 0°-40°
Receiver Protocol: ELRS 2.4G
VTX: M04 25-400mW VTX
Battery: 2*BT2.0 450mAh 1S 30C Battery
Flight time: 5 mins



Downloads
FC Firmware and ESC download
 
Includes


1 x Cetus X Brushless Quadcopter
1 x BT2.0 Battery Charger and Voltage Tester
2 x BT2.0 450mAh 1S 30C Battery
1 x Phillips Screwdriver
1 x Prop Removal Tool
1 x Type-C Adapter
4 x Gemfan 2020 4-Blades Props

 


All batteries must be shipped by a ground shipping method.
Cetus X Brushless Quadcopter is a 2S power whoop drone and a primary choice for beginners who want to get advanced flight skills. It features a stronger propulsion system for a speedier and more violent flight, which is capable of performing diverse freestyle tricks. Equipped with M04 400mW VTX and C04 FPV camera that is optimized for longer radio and video transmission. Meanwhile, it supports the Betaflight configurator which is a popular application to configure RC aircraft.
Check out our other RTF combos, all our pre-built quads and our BetaFPV selection!
Features

An excellent preference for beginners to get advanced level. Cetus X brushless Quadcopter is proud of its lightning speed with rapid startup due to its stronger propulsion system.
Build-in ExpressLRS 2.4G receiver that is the most popular radio link, low latency, and far controlling range are possible. Pilots can not only enjoy the flight indoors but also explore the scenery outdoor.

Featuring M04 400mW VTX, C04 FPV camera (based on Caddx Nano Ant Camera or Runcam Nano 4), and 2xBT2.0 450mAh 1S 30C battery for longer radio and video transmission and flight endurance, Cetus X brushless quadcopter allows beginners to gain more achievements in FPV flight.

Classical white design inherited from Cetus Series and made of PA12 material, Cetus X frame has an excellent impact resistance in drop &amp impact. The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots.

Specifications

Item: Cetus X Brushless Quadcopter
Weight: 55g
Wheelbase: 95mm
FC*: F4 2S 15A V1.0 (Betaflight FC Version)

Motors: 1103 11000KV Motor

Props: Gemfan 2020 4-Blades Props
Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4)
Camera Adjustable Angle: 0°-40°
Receiver Protocol: ELRS 2.4G
VTX: M04 25-400mW VTX
Battery: 2*BT2.0 450mAh 1S 30C Battery
Flight time: 5 mins





Downloads
FC Firmware and ESC download

Includes


1 x Cetus X Brushless Quadcopter
1 x BT2.0 Battery Charger and Voltage Tester
2 x BT2.0 450mAh 1S 30C Battery
1 x Phillips Screwdriver
1 x Prop Removal Tool
1 x Type-C Adapter
4 x Gemfan 2020 4-Blades Props




Cetus X Brushless Quadcopter is a 2S power whoop drone and a primary choice for beginners who want to get advanced flight skills. It features a stronger propulsion system for a speedier and more violent flight, which is capable of performing diverse freestyle tricks. Equipped with M04 400mW VTX and C04 FPV camera that is optimized for longer radio and video transmission. Meanwhile, it supports the Betaflight configurator which is a popular application to configure RC aircraft. Check out our other RTF combos, all our pre-built quads and our BetaFPV selection! Features An excellent preference for beginners to get advanced level. Cetus X brushless Quadcopter is proud of its lightning speed with rapid startup due to its stronger propulsion system. Build-in ExpressLRS 2.4G receiver that is the most popular radio link, low latency, and far controlling range are possible. Pilots can not only enjoy the flight indoors but also explore the scenery outdoor. Featuring M04 400mW VTX, C04 FPV camera (based on Caddx Nano Ant Camera or Runcam Nano 4), and 2xBT2.0 450mAh 1S 30C battery for longer radio and video transmission and flight endurance, Cetus X brushless quadcopter allows beginners to gain more achievements in FPV flight. Classical white design inherited from Cetus Series and made of PA12 material, Cetus X frame has an excellent impact resistance in drop & impact. The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots. Specifications Item: Cetus X Brushless Quadcopter Weight: 55g Wheelbase: 95mm FC*: F4 2S 15A V1.0 (Betaflight FC Version) Motors: 1103 11000KV Motor Props: Gemfan 2020 4-Blades Props Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4) Camera Adjustable Angle: 0°-40° Receiver Protocol: ELRS 2.4G VTX: M04 25-400mW VTX Battery: 2*BT2.0 450mAh 1S 30C Battery Flight time: 5 mins Downloads FC Firmware and ESC download Includes 1 x Cetus X Brushless Quadcopter 1 x BT2.0 Battery Charger and Voltage Tester 2 x BT2.0 450mAh 1S 30C Battery 1 x Phillips Screwdriver 1 x Prop Removal Tool 1 x Type-C Adapter 4 x Gemfan 2020 4-Blades Props

Cetus X Brushless Quadcopter is a 2S power whoop drone and a primary choice for beginners who want to get advanced flight skills. It features a stronger propulsion system for a speedier and more violent flight, which is capable of performing diverse freestyle tricks. Equipped with M04 400mW VTX and C04 FPV camera that 

BetaFPV Cetus X 2S Brushless Quadcopter - ELRS 2.4GHz

BETAFPV Hobby 

Cetus X is a primary choice for beginners who want to get advanced flight skills. The 2S power makes it stands out, giving Cetus X stronger propulsion and faster speed to perform diverse freestyle tricks. Equipped with M04 400mW VTX and C04 FPV camera that is optimized for longer radio and video transmission. Two FC versions provide different functions to pilots but all help pilots to the next level.
Cetus X RTF FPV Kit is available now! Please click here to buy.
Recommend the newest BT2.0 550mAh 1S Battery. More flight time and higher discharge rate.


Bullet Point

An excellent preference for beginners to get advanced level. Cetus X brushless Quadcopter is proud of its lightning speed with rapid startup due to its stronger propulsion system.
Build-in ExpressLRS 2.4G receiver that is the most popular radio link, low latency, and far controlling range are possible. Pilots can not only enjoy the flight indoors but also explore the scenery outdoors.
The drone with Frsky receiver protocol version is also provided for customers who used to have LiteRadio 2 SE radio transmitter in Cetus Pro or Cetus RTF Kit.

Featuring M04 400mW VTX, C04 FPV camera (based on Caddx Nano Ant Camera or Runcam Nano 4), and BT2.0 450mAh 1S 75C battery for longer radio and video transmission and flight endurance, Cetus X brushless quadcopter allows beginners to gain more achievements in FPV flight.
The Betaflight FC comes with the most popular firmware in the FPV community. Beginners are able to learn and understand more about FPV, which is an essential way to get drone experience.
The Cetus FC version offers an auxiliary flight function for pilots with three speed modes. It is easier and more suitable for initial pilots.
Classical white design inherited from Cetus Series and made of PA12 material, Cetus X frame has an excellent impact resistance in drop &amp impact. The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots.

Specification

Item: Cetus X Brushless Quadcopter
Weight: 55g
Wheelbase: 95mm
FC*: F4 2S 15A V1.0 (Betaflight FC Version)/Cetus BL V3 Flight Controller (Cetus FC Version)

Motors: 1103 11000KV Motor

Props: Gemfan 2020 4-Blades Props

Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4)
Camera Adjustable Angle: 0°-40°
Frame: Cetus X Brushless Whoop Frame

Receiver Protocol: ELRS 2.4G (Betaflight FC Version)/Frsky D8 (Cetus FC Version)

VTX: M04 25-400mW VTX (Betaflight FC Version)/Cetus 25-350mW VTX V2 (Cetus FC Version)
Battery*: BT2.0 450mAh 1S 75C Battery

Flight time: 5 mins

Note: FC (Betaflight FC Version) has been replaced from F4 1S 12A FC to F4 2S 15A V1.0 since Sep 2023. The battery will be upgraded from BT2.0 450mAh 1S 30C Battery to BT2.0 450mAh 1S 75C Battery from Feb 2024.


ExpressLRS 2.4G

Equipped with F4 2S 15A V1.0 FC and Cetus BL V3 FC, Cetus X brushless quadcopter supports ELRS 2.4G RX protocol. And F4 2S 15A V1.0 FC RX version supports Betaflight configurator, while Cetus BL V3 FC does not. Pilots who had Cetus Pro or Cetus RTF Kit can continue to use LiteRadio 2 SE radio transmitter to fly Cetus X Frsky D8 version.

Cetus FC or Betaflight FC

Cetus X with the classical Cetus flight controller version is released. It supports the position hold function, which provides easier control to pilots. If select the Betaflight FC version, pilots are able to learn and understand the drone configuration. Both FC versions perform great in power and speed and have higher-grade flight modes for pilots to get advanced.




Cetus FC Version
Betaflight FC Version



Flight Controller
Cetus BL V3 FC
F4 2S 15A V1.0 FC


Receiver Protocol
Frsky D8
ExpressLRS 2.4G


Flight Mode
N/S/M/Turtle Mode
Angle/Horizon/Air/Turtle Mode


VTX
25-350mW
25-400mW


Position Hold
Support
Not Support


Configuration Software

BETAFPV Configurator

Betaflight Configurator



Note: FC (Betaflight FC Version) has been replaced from F4 1S 12A FC to F4 2S 15A V1.0 since Sep 2023.

Note: Pilots who have LiteRadio 2 SE in Cetus or Cetus Pro FPV Kit can bind and fly the Cetus X Cetus FC version.
Auxiliary Flight Function
Built-in highly precise barometer to detect the height, the version with Cetus FC benefits from great stability due to its position hold mode, and auto-hovering, which enables the drone to stay at the current height. This function also ensures an emergency landing of the drone whenever loses control or is on low battery. Meanwhile, its stable flight allows you to catch the best footage with the FPV Goggles. It really does an immense amount of fun and ease of flight for all pilots. Recommend flying it with BETAFPV VR03 Goggles.
Powered by 2S, Cetus X has loads of punch and speed, making it smoother and more suitable for outdoor practice, great for the next level. For indoor practice, the Cetus Pro with 1S power, which has the same auxiliary flight function, is easier for initial pilots to control and fly.

Note: The position hold function is only available in N mode.
Improved Video Transmission

Cetus X Brushless Quadcopter comes with M04 25-400mW VTX and C04 FPV camera. The VTX features a lightweight and adjustable output power for longer distance flying. Combining this VTX and the excellent radio link ExpressLRS 2.4G/Frsky D8, pilots can fly whoop drones longer to explore more possibilities and have fun. In addition, C04 FPV camera (based on Caddx Nano Ant Camera/Runcam Nano 4) shows better quality in FPV flight compared with C02 FPV camera.

Powerful Propulsion System

Equipped with 1103 11000KV Brushless Motor and Gemfan 2020 4-blade props. 1103 motors are designed for 2S quadcopters with incredible power, smooth and quiet operation, and light enough. Besides, Cetus X quadcopter adopts 2020 4-blade props, which are lighter and durable enough, offering pilots a high-efficiency flight experience.

Primary Choice for Next Level
Cetus X Brushless Qaducopter Betaflight FC version supports configuring on Betaflight configurator. It is a primary choice for beginners who start to learn drone configuring, which helps beginners to get advanced level. With the Betaflight configurator, you can calibrate accelerometer, custom OSD content, adjust the video transmitter and etc.

Note: Please DO NOT configure ESC or Motor settings on Betaflight configurator.
Betaflight Flight Controller
Cetus X brushless quadcopter is built-in F4 2S 15A V1.0 FC, supporting ELRS 2.4G protocol. The ELRS 2.4G version comes with betaflight 4.3.1 FC firmware so it supports ELRS V2.0. The ESC on the new board powered by BB51 hardware comes with Bluejay 48k ESC firmware, allowing 1103 11000KV motors to give full play to the efficiency of power. We update the gyro to BOSH BMI270 for better performance and stability since the new F4 2S 15A V1.0 FC.




Cetus X (ELRS 2.4G)
Cetus X (Frsky D8)


FC Inside
F4 2S 15A V1.0
F4 1S 12A FC SPI Frsky


Gyro

BMI270
BMI270


FC Firmware
BETAFPVF411SX1280
BETAFPVF411RX


ESC Firmware
C_X_70_48_ for Bluejay BB51 hardware
C_X_30_48_ for Bluejay BB51 hardware



Click here to know more information about F4 1S 12A Flight Controller ELRS or Frsky.
Since Sep 2023, FC (Betaflight FC version) has been replaced from F4 1S 12A FC to F4 2S 15A V1.0. Here are the differences between them.




F4 1S 12A FC
F4 2S 15A V1.0 FC


Built-in ESC
12A continuous and peak 25A current
15A continuous and peak 25A current


Version
ELRS, Frsky
ELRS


ESC Input Voltage
1S-2S

2S


ESC Firmware
C_X_30_48_V0.18.1.hex for BB51 Bluejay hardware
C_X_70_48_V0.19.2.hex for BB51 Bluejay hardware


RGB Light
0
2


USB Port Position
Middle of the board
Tail of the board



Click here to know more information about F4 1S 12A Flight Controller ELRS or Frsky.
For Cetus X ELRS 2.4G version, the Betaflight firmware 4.3.0 and up start to support BMI270 gyro. For Frsky D8 version, we recommend using BETAFPVF411RX 4.2.11 firmware and CLI dump file offered by BETAFPV. 
The default flight controller firmware enables bidirectional D-shot and is compatible with Bluejay ESC firmware. If you update the 4.3.0 and up firmware for ELRS 2.4G from the Betaflight official site, please flash the CLI dump file for Cetus X.
Download the firmware and CLI dump file for Cetus X ELRS 2.4G or Frsky.
The Bluejay firmware could support the BB51 hardware now. Both ELRS and Frsky boards are powered by BB51 hardware. If you want to setup the ESC specification, please use the BLHeliSuite16714902A_Beta or ESC-Configurator.

ESC-Configurator: https://preview.esc-configurator.com/

Download BLHeliSuite16714902A_Beta here.
Download the Bluejay ESC firmware here.

Note: Only ELRS 2.4G version supports motor direction set through Betaflight Configurator and SPI Frsky version does not support it. BLHeli Configurator and Bluejay Configurator are invalid for the BB51 ESC (both versions).
Recommended Parts

Radio Transmitter: LiteRadio3, LiteRadio 2 SE
Goggles: VR02 FPV Goggles, VR03 FPV Goggles
Battery: BT2.0 450mAh 1S 30C Battery, BT2.0 550mAh 1S Battery
Props: Gemfan 2020 4-Blade Propellers
Camera: C04 Camera and VTX Module


FAQ

ExpressLRS 2.4G is the most popular radio link now. Know more about ExpressLRS here.
The frame and props are visible when the camera's angle is 0°. Adjust it to about 25°, then the frame and props are invisible when flying.


Download the CLI dump file for Cetus X (Betaflight F4 1S 12A FC version).

Download the CLI dump file for Cetus X (Betaflight F4 2S 15A V1.0 FC version).


Download the CLI dump file for Cetus X (Cetus FC version).

Download the Manual for Cetus X (Betaflight F4 1S 12A FC version).


Download the Manual for Cetus X (Betaflight F4 2S 15A V1.0 FC version).


 Download the Manual for Cetus X (Cetus FC version).

Cetus X Brushless Quadcopter should work with two 1S batteries. Do not recommend using different brand batteries. Highly recommend the original batteries BT2.0 450mAh 1S 30C Battery.
Cetus X Brushless Quadcopter is similar to Meteor85 Brushless Whoop Quadcopter (2S) in many ways. For flying maneuverability and more battery choices, Meteor85 is a good alternative choice.

Package

1 * Cetus X Brushless Quadcopter
1 * BT2.0 Battery Charger and Voltage Tester
2 * BT2.0 450mAh 1S 75C Battery
1 * Phillips Screwdriver
1 * Prop Removal Tool
1 * Type-C Adapter
4 * Gemfan 2020 4-Blades Props



Cetus X is a primary choice for beginners who want to get advanced flight skills. The 2S power makes it stands out, giving Cetus X stronger propulsion and faster speed to perform diverse freestyle tricks. Equipped with M04 400mW VTX and C04 FPV camera that is optimized for longer radio and video transmission. Two FC ve

Cetus X Brushless Quadcopter

SpeedyBee

SpeedyBee PNP Flex25 Analog Cinewhoop

 Check out all our Analog BNF/PNP/RTF Drones and the rest of our SpeedyBee Products!  Don't forget to get the LED Lighting Kit to add some bling to your drone! Specifications: Wheelbase: 78mm Flight Controller &amp; ESC SpeedyBee: F745 35A AIO Gyro: MPU6000 OSD Chip: AT7456E VTX SpeedyBee: TX800 Camera: RunCam Phoenix 

SpeedyBee Flex25 Analog 2.5

SpeedyBee PNP Flex25 HD Falcon/Runcam Link Cinewhoop

 Check out all our Digital BNF/PNP/RTF Drones and the rest of our SpeedyBee Products!  Don't forget to get the LED Lighting Kit to add some bling to your drone! Specifications: Wheelbase: 78mm Flight Controller &amp; ESC SpeedyBee: F745 35A AIO Gyro: MPU6000 OSD Chip: AT7456E VTX &amp; Camera: RunCam Falcon 120fps Digi

SpeedyBee Flex25 HD 2.5

EMAX

EMAX BNF/ PNP Hawk Apex 3.5" HDZero Quadcopter

EMAX Apex 3.5 Inch HDZero Ultralight Racing Drone PNP ELRS

The best quality First Person View equipment. Free or discounted shipping on all orders.Drone Racing, RC Airplanes, FPV Cameras, FPV Goggles, Video Transmitters, RC Quads, Drone Antennas, Lipo Batteries, and Ground Station Equipment.All available for amateurs, schools, hobbyists, government, and wholesale buyers.

EMAX Apex 3.5 Inch HDZero Ultralight Racing Drone PNP ELRS - RMRC

Improvement requires evolution, changing the status quo, and forming new normals. In our constant quest for self-improvement, a new meta has been formed through the Hawk Apex. In a game of predator and prey, every movement counts and every engineered detail plays a role. In a high stakes race, the ability to see clearl

Emax Hawk Apex 3.5

  THIS PRODUCT REQUIRES HDZERO VIDEO RECEIVER FOR USE: HDZero VRX  Wheelbase: 162mm Motor: ECO II 2004 3000kv Propeller: Avia 3630 Tri-blade Weight (excluding battery): 167g AIO: STM32F722 + 4 IN 1 25A ESC VTX: HDZero Whoop VTX  Camera: Runcam Nano HDZero VTX Antenna: EMAX Nano Antenna UFL BNF Variant Receiver: EMAX Ex

Hawk Apex 3.5 Inch HDZero Ultralight Racing Drone

Emax USA

 


THIS PRODUCT REQUIRES HDZERO VIDEO RECEIVER FOR USE: HDZero VRX 

Wheelbase: 162mm
Motor: ECO II 2004 3000kv
Propeller: Avia 3630 Tri-blade
Weight (excluding battery): 167g
AIO: STM32F722 + 4 IN 1 25A ESC
VTX: HDZero Whoop VTX 
Camera: Runcam Nano HDZero
VTX Antenna: EMAX Nano Antenna UFL
BNF Variant Receiver: EMAX ExpressLRS RX
Recommended Battery: 4S XT30

Hawk Apex 3.5 Inch HDZero Ultralight Racing Drone from WREKD Co.

EMAX BNF/PNP Hawk Apex 5" HDZero Quadcopter

Emax Hawk Apex 5

  THIS PRODUCT REQUIRES HDZERO VIDEO RECEIVER FOR USE: HDZero VRX  Motor: ECO II 2004 Propeller: Avia 5030 Tri-blade Weight (excluding battery): 167g AIO: STM32F722 + 4 IN 1 25A ESC VTX: HDZero Whoop VTX  Camera: Runcam Nano HDZero VTX Antenna: EMAX Nano Antenna UFL BNF Variant Receiver: EMAX ExpressLRS RX Recommended 

Hawk Apex 5 Inch HDZero Ultralight Racing Drone

 


THIS PRODUCT REQUIRES HDZERO VIDEO RECEIVER FOR USE: HDZero VRX 



Motor: ECO II 2004
Propeller: Avia 5030 Tri-blade

Weight (excluding battery): 167g
AIO: STM32F722 + 4 IN 1 25A ESC
VTX: HDZero Whoop VTX 
Camera: Runcam Nano HDZero
VTX Antenna: EMAX Nano Antenna UFL
BNF Variant Receiver: EMAX ExpressLRS RX
Recommended Battery: 4S XT30
 

Hawk Apex 5 Inch HDZero Ultralight Racing Drone from WREKD Co.

Foxeer

Foxeer BNF Caesar Analog 5" Racing Quadcopter

Introducing the new Caesar 5" Racing Drone from Foxeer. It uses high performance T700 carbon for increased stiffness and vibration reduction as well as Foxeer's famously durable Reaper electronics allowing you to reduce your filtering giving you reduced latency for that locked in racing feel. Pick up yours today! ﻿Note

Foxeer Caesar 5

DarwinFPV

DarwinFPV BNF TinyApe Freestyle 2.5" Quadcopter

The DarwinFPV Tiny Ape Freestyle is the first 2.5'' drone from DarwinFPV. This drone was designed to meet the needs of pilots and comes with the Darwin ELRS2.0 F411 15A Bluejay AIO and the VTX006 which has 25-600mW output power.

DarwinFPV Tiny Ape Freestyle 2.5" Quadcopter - ExpressLRS

DarwinFPV Tiny Ape Freestyle 2.5&quot Quadcopter - ExpressLRS

Darwin FPV BNF Tiny Ape Freestyle 2S 2.5" Quad is the first 2.5'' drone from Darwin fpv. Designed to meet the needs of more pilots, it comes with the Darwin F411 15A Bluejay AIO FC with integrated ELRS2.0 RX, 25-600mW VTX and RunCam Nano 4. Check out the reviews below!
Make sure to check out all of our BNF quads as well as the rest of our DarwinFPV selection!

 


Specifications

FC&ampESC：F411 1-3S 15A FC(Built-in ELRS 2.4G receiver)

Built-in Receiver Protocol: SPI ELRS 2.4G
Motor: 1103 8000KV Brushless Motor
Camera: RunCam Nano 4
VTX: 25-600mW VTX
Propeller: Gemfan 2512 3-blade propeller
AIO Firmware Target: DARWINF4SX1280HD
ESC Firmware: Bluejay_S_H_50_48_v0.14
Recommended Battery:  2S 380-450mah
Weight: 50.3g w/o battery &amp props

Includes

1x DarwinFPV BNF TinyApe Freestyle 2S 2.5" Quad - ELRS


Make sure not to miss out on our Darwin FPV BNF Tiny Ape Freestyle 2S 2.5" Quad - ELRS and the perks of a mini drone. Fly with pride today!

DarwinFPV BNF Tiny Ape Freestyle 2S 2.5" Analog Quad - ELRS

DarwinFPV BNF TinyApe Freestyle 2S 2.5" Quad - ELRS For Sale

Tiny Ape Freestyle is the first 2.5'' drone for Darwinfpv. In order to meet the needs of more friends and we have made multiple attempts. It comes with the Darwin ELRS2.0 F411 15A Bluejay AIO and the VTX006 which has 25-600mW output power. NOTE: Runcam Thumb Camera NOT Included Check out all our Analog BNF Drones and t

DarwinFPV TinyApe Freestyle 2.5

Darwin FPV BNF Tiny Ape Freestyle 2S 2.5" Quad is the first 2.5'' drone from Darwin fpv. Designed to meet the needs of more pilots, it comes with the Darwin F411 15A Bluejay AIO FC with integrated ELRS2.0 RX, 25-600mW VTX and RunCam Nano 4. Check out the reviews below! Make sure to check out all of our BNF quads as wel

DarwinFPV BNF Tiny Ape Freestyle 2S 2.5" Analog Quad - ELRS from WREKD Co.

DarwinFPV BNF Tiny Ape Freestyle 2S 2.5

GEPRC BNF GEP-MK5 Mark5 HD 5" Quadcopter

Recommend GEPRC Storm 1550mAh Battery for MARK5 4S Version
Recommend GEPRC Storm 1400mAh Battery for MARK5 6S Version
Note: From August 18, 2023, any purchase of a 5-inch drone will receive a free pack of 5040 propellers in random colors.

Recommend GEPRC Storm 1550mAh Battery for MARK5 4S Version Recommend GEPRC Storm 1400mAh Battery for MARK5 6S Version Note: From August 18, 2023, any purchase of a 5-inch drone will receive a free pack of 5040 propellers in random colors.

GEPRC MARK5 HD DJI AIR UNIT Freestyle FPV Drone - GEPRC

GEPRC MARK5 HD DJI AIR UNIT Freestyle FPV Drone

Pre-Orders shipping ASAP!
The GEPRC BNF Mark5 HD Quad w/ Caddx Air Unit Micro is developed specifically for freestyle with squashed X arm design. Unique shock absorbing structure design, less vibrations and resonance, to provide a stable operating environment for the electronic system. Aluminum alloy side plates not only look stunning, but also reduce weight and add more endurance. 
Make sure to check the ELRS Version!
Gopro case available separately.
Check out all our pre-built quads, and all our GEPRC selection!



Specifications

Input Voltage: 6S

Wheelbase: 225mm
Top plate: 2.5mm
Bottom plate: 2.5mm
Arm: 5mm
Charge connector: XT60
Motor: 2107.5 1960Kv

Weight: 385.5g

SPAN F722-HD-BT FC

MCU: STM32F722
IMU: MPU6000(SPI)
OSD: BetaFlight OSD w/AT7456E chip
Blackbox: 16Mb Flash
BEC: 5V, 9V

LC Filter: Yes

G50A ESC

MCU: STM32F051K86
Max Continuous Current: 50A
Max Burst Current: 55A
BEC: No
Current Sensor: Yes

Caddx Air Unit

Operating Temperature: 32 to 104 F (0 to 40 C)Input Power: 7.4-17.6V
Transmitter Power: FCC/SRRC: &lt30dBm CE: &lt14dBm
I/O Interface: USB-C, MMCX, 3-in1 Port, MicroSD
Output Power: 25mW3200mW/500mW/700mW
Video Transmission: 28ms Low Latency
Dimensions:

Air Unit: 44x37.8x14.4mm
Camera:20.7x19x19mm

Flight Control System: BetaFlight
Max Transmission Range: 4km
Coaxial Cable Length: 100mm
FOV: 150(D) 122(H) 93(V)
Goggle Compatibility: DJI
Closed Loop 4-in-1: Yes
Frequency Channels: 8
Shutter: Rolling Shutter
Sensor: 1/3.2" CMOS
Effective Pixels: 4 M
Image: 720p/120fps
Video Format: MP4
Video: 1080p/60fps
Lens: 2.1mm, F/21
ISO: 100-256000

Includes

1x GepRC BNF Mk5 Quad
4x Freestyle 4S propellers (pair)
1x Battery strap M15x250mm
2x Battery strap M20x220mm
2x Battery Silicone Pads
1x Camera cage carbon top plate
1x 3D print mountings combination
2x Action camera mount holder
1x Set of screws
1x Set of screwdrivers
1x Antenna fixed tube
