FPV Quad Parts

Peripherals and Replacement Parts

Equipment

Equipment Peripherals

Build Page Parts

Build Parts Equipment

Pre-Built Quads and Kits 

Build Page Parts Overflow

Build Parts Equipment Overflow

Compatibility Categories

Continuous Amp Rating

Flywoo

Flywoo GOKU GN405 35A 2-6S 16x16 Flight Controller Stack - GN405 Nano FC, 35A ESC











Unleash the power of your drone with Flywoo&#39s GOKU GN405 Nano 35A STACK! This tiny, but powerful flight controller is packed with features, such as a barometer, 16MB blackbox, 6 serial ports, I2C functionality and WS2812 LEDs.  All these amazing features on 16x16mm platform with this Flywoo stack!










Check out all our 16x16 stacks, and our Flywoo gear selection!
Features

F405 BGA MCU
Barometer
5V 2A BEC
Black Box 16MB
6 UARTS
WS2812LED

Specifications
GOKU GN405 Nano 16x16 FC 

MCU: STM32F405 BGA
IMU: ICM42688
Barometer: DPS310

input voltage: 2-6S
Onboard LED: WS2812x4
6 hardware UARTS (UART1,2,3,4,5,6)
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only.
PPM and PWM receivers are not supported.
Onbord 16Mbytes for Blackbox logging
5V Power Out: 2.0A max
3.3V Power Out: 0.5A max
Dimensions: 22x22mm
Mounting Holes: Standard 16/16mm square to center of holes
Weight: 2.3g
Firrmware : FLYWOOF405NANO

BS35A BLheli_S 2-4S 4in1

Weight: 2.5g
Mounting Hole: 16x16mm (M3)
Input voltage: 2-6S
Support Oneshot, Multishot,  DShot150/300/600

Includes

1x Flywoo GOKU GN405 F405 Nano 2-6S AIO 16x16 Flight Controller w/ 35A 8Bit 4in1 ESC

Wiring Diagram 


Unleash the power of your drone with Flywoo's GOKU GN405 Nano 35A STACK! This tiny, but powerful flight controller is packed with features, such as a barometer, 16MB blackbox, 6 serial ports, I2C functionality and WS2812 LEDs.  All these amazing features on 16x16mm platform with this Flywoo stack! Check out all our 16x

Flywoo GOKU GN405 F4 2-6S 16x16 Stack/Combo (F4 FC / 35A 8Bit 4in1 ESC) from WREKD Co.

Flywoo GOKU GN405 F4 2-6S 16x16 Stack/Combo (F4 FC / 35A 8Bit 4in1 ESC)

FLYWOO











Unleash the power of your drone with Flywoo's GOKU GN405 Nano 35A STACK! This tiny, but powerful flight controller is packed with features, such as a barometer, 16MB blackbox, 6 serial ports, I2C functionality and WS2812 LEDs.  All these amazing features on 16x16mm platform with this Flywoo stack!










Check out all our 16x16 stacks, and our Flywoo gear selection!
Features

F405 BGA MCU
Barometer
5V 2A BEC
Black Box 16MB
6 UARTS
WS2812LED

Specifications
GOKU GN405 Nano 16x16 FC 

MCU: STM32F405 BGA
IMU: ICM42688
Barometer: DPS310

input voltage: 2-6S
Onboard LED: WS2812x4
6 hardware UARTS (UART1,2,3,4,5,6)
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only.
PPM and PWM receivers are not supported.
Onbord 16Mbytes for Blackbox logging
5V Power Out: 2.0A max
3.3V Power Out: 0.5A max
Dimensions: 22x22mm
Mounting Holes: Standard 16/16mm square to center of holes
Weight: 2.3g
Firrmware : FLYWOOF405NANO

BS35A BLheli_S 2-4S 4in1

Weight: 2.5g
Mounting Hole: 16x16mm (M3)
Input voltage: 2-6S
Support Oneshot, Multishot,  DShot150/300/600

Includes

1x Flywoo GOKU GN405 F405 Nano 2-6S AIO 16x16 Flight Controller w/ 35A 8Bit 4in1 ESC

Wiring Diagram 


Flywoo GOKU GN405 F4 2-6S 16x16 Stack/Combo (F4 FC / 35A 8Bit 4in1 ESC

Processor (MCU)

The FC is the brain or the CPU of your quad. It has a processor and other components that allow it to listen to your inputs and tells the quad what to do. FCs are commonly sold together with other components integrated or stacked (like ESCs and video transmitters). For beginners, choose a FC with a F4 or F7 processor that has a compatible mount with your frame. 

Flight Controllers

FC Stack Mount

Built-in VTX

Built-in ESC

Flywoo GOKU GN405 13A 2-4S 16x16 Flight Controller Stack - GN405 Nano FC, 13A 4in1 ESC

With an already impressive lineup of flight controllers, Flywoo has released the GOKU GN405 Nano. An economical and durable stack, the GN405 is packed with features including a barometer, 16MB black box, 6 complete hardware serial ports, I2C functionality, and WS2812 LEDs on each corner. It is specifically designed to be pin mounted to the GOKU BS13A / 35A 4-in-1 16x16 ESCs but can also be soldered via pads. The programmable WS2812 LED on each corner provides low-profile lighting for this tiny FC
Check out all our 16x16 stacks, and our Flywoo gear selection!
Specifications
GN405 NANO FC

Dimensions: 22x22mm
Weight: 2.3g
Mounting Pattern: 16x16, M3 Holes
MCU: STM32F405 BGA

UARTS: 6 1/2/3/4/5/6
I2C: SCL/SDA
GYRO: ICM42688
BARO: BMP280
BEC: 5V 2A
LED: 4x WS2812
FLASH: 8M
Input Voltage: 2-6S
Firmware: FLYWOOF405NANO


BS13A 4-IN-1 ESC

Support: Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input Voltage: 2-4S Lipo
Continuous Current: 13A
Firmware: BLHELI_S
Mounting Pattern: 16x16mm
Weight: 2.5g

Includes

1x GOKU GN405 &ampamp  BS13A 2-4S 16x16 Stack/Combo  

Wiring Diagram



With an already impressive lineup of flight controllers, Flywoo has released the GOKU GN405 Nano. An economical and durable stack, the GN405 is packed with features including a barometer, 16MB black box, 6 complete hardware serial ports, I2C functionality, and WS2812 LEDs on each corner. It is specifically designed to 

Flywoo GOKU GN405 2-4S 16x16 Stack/Combo (GN405 NANO FC / 13A 4in1 ESC) from WREKD Co.

Flywoo GOKU GN405 2-4S 16x16 Stack/Combo (GN405 NANO FC / 13A 4in1 ESC)

With an already impressive lineup of flight controllers, Flywoo has released the GOKU GN405 Nano. An economical and durable stack, the GN405 is packed with features including a barometer, 16MB black box, 6 complete hardware serial ports, I2C functionality, and WS2812 LEDs on each corner. It is specifically designed to be pin mounted to the GOKU BS13A / 35A 4-in-1 16x16 ESCs but can also be soldered via pads. The programmable WS2812 LED on each corner provides low-profile lighting for this tiny FC
Check out all our 16x16 stacks, and our Flywoo gear selection!
Specifications
GN405 NANO FC

Dimensions: 22x22mm
Weight: 2.3g
Mounting Pattern: 16x16, M3 Holes
MCU: STM32F405 BGA

UARTS: 6 1/2/3/4/5/6
I2C: SCL/SDA
GYRO: ICM42688
BARO: BMP280
BEC: 5V 2A
LED: 4x WS2812
FLASH: 8M
Input Voltage: 2-6S
Firmware: FLYWOOF405NANO


BS13A 4-IN-1 ESC

Support: Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input Voltage: 2-4S Lipo
Continuous Current: 13A
Firmware: BLHELI_S
Mounting Pattern: 16x16mm
Weight: 2.5g

Includes

1x GOKU GN405 &amp  BS13A 2-4S 16x16 Stack/Combo  

Wiring Diagram



Flywoo GOKU GN405 2-4S 16x16 Stack/Combo (GN405 NANO FC / 13A 4in1 ESC

GEPRC

GEPRC STABLE F411 16x16 Flight Controller

WREKD is a family-owned & operated, leading online FPV super-store based in the United States specializing in FPV racing / freestyle / tiny / micro whoop drones, parts, gear, and accessories. We offer fast, domestic, same-day shipping with the quickest delivery to anywhere in the U.S.A.

GEP F411-STABLE F4 FLIGHT CONTROLLER 16*16 from WREKD Co.

GEP F411-STABLE F4 FLIGHT CONTROLLER 16*16

Replacement flight controller for the GEPRC Phantom.Check out our full line of Micro Flight Controllers. STABLE F411 Flight Controller(16*16mm) MCU: STM32F411 IMU: MPU6000 gyro/accelerometer (SPI) OSD: BetaFlight OSD w/ AT7456E chip BEC Output: 5V@2A Size: 21mm*21mm Mounting holes: 16mm*16mm Integrated LC Filter Input 

GEPRC F411-STABLE F4 FLIGHT CONTROLLER 16*16

ESC Stack Mount

The ESC(s) controls your motors’ speed. It draws power from the battery to spin the motors based on what the FC tells it to do. Each motor needs an ESC. It’s common today to see 4-in-1 ESCs so you only need to buy a single part. For beginners, choose a 4-in-1 ESC that has a compatible mount with your frame and FC. The biggest consideration is amperage limit. We show you ESCs with appropriate amperage limits based on your frame size. You can calculate how much amperage you need based on your motor and prop choice. 

ESCs

Frame Stack Mount

The frame is typically the first part to pick because it determines what kind of flying you’ll be doing the most. Start by picking a frame type, and narrow down the options by propeller size. The frame holds your quad parts together and heavily impacts what the quad can do. 

Frames

The VTX processes the image from your FPV camera and sends it to your goggle’s video receiver (VRX). If you chose as digital video system, you need a VTX that matches the system. Most analog VTXs and VRXs are compatible with each other, and your biggest consideration will be how much output power you need. The more output power, the more range and better signal you’ll get. Learn more about VTXs.