FPV Quad Parts

Peripherals and Replacement Parts

Equipment

Equipment Peripherals

Build Page Parts

Build Parts Equipment

Pre-Built Quads and Kits 

Build Page Parts Overflow

Build Parts Equipment Overflow

Compatibility Categories

Continuous Amp Rating

NewBeeDrone

NewBeeDrone BeeBrain BLV4 AIO Flight Controller - 12A ESC, 2.4GHz ELRS

NewBeeDrone BeeBrain BLV4 AIO Flight Controller ExpressLRS (ELRS) 2.4G
 
Warning! The BeeBrainBLV4 OSD might not compatible with third party camera. If you are planning to use it for customized build, Please be aware it only support the camera below: 
How to Video:Internal ELRS Rx Firmware flashing: 
NewBeeDrone BeeEye CameraRuncam Nano4 
Specifications

STM32F411 MCU
ESC Firmware: S-H-40 - Bluejay, 0.16, 48kHz.
ESC Specifications: 4 channel 12A ESC
ESC Connector: JST-1.0 3Pin
NBD OSD (Betaflight OSD Compatible)
Weight: 6.5 grams (including antennas and battery connector)
Size: Outer dimensions 29 x 29 x 7.6 mm
Holes: 25.5 x 25.5 mm
Battery input: 1S
Connector: PH2.0
UART2 TX and RX for onboard EXPRESSLRS receiver (SX1280)
UART1 TX and RX free
VTX Adjustble power: 5mW-25mW-SmartMAX. SmartMAX will automatically adjust the VTX power according to the board temperature. When the board temperature rises, the VTX power will be automatically reduced. When the temperature is low, the maximum output power can be up to 400mW

Includes

1 x BeeBrain BLV4 Flight Controller
4 x Grommet
4 x Screw

1 x Receiver T-Antennas 


1 x Receiver Antennas


1 x VTX Antenna


Firmware: 1. ELRS Receiver firmware can be found here. Vendor choose NewBeeDrone2. BeeBrain blv4 ELRS Betaflight 4.4 firmware
All new firmware can be found on our Github Page
 Note: Binding process. power up the drone 3 times, on the third time you plug in power, the ELRS Receiver will get into binding mode. We are still trying to work on the ELRS firmware and make it able to just click the boot button to get into bind mode. Will get this update in the near future. Check out the video below CiottiFPV show you how to get into bind mode. - Thanks bro for showing this. lol 






NewBeeDrone BeeBrain BLV4 AIO Flight Controller ExpressLRS (ELRS) 2.4G   Warning! The BeeBrainBLV4 OSD might not compatible with third party camera. If you are planning to use it for customized build, Please be aware it only support the camera below:  How to Video:Internal ELRS Rx Firmware flashing: NewBeeDrone BeeEye 

NewBeeDrone BeeBrain BLV4 AIO Flight Controller  ExpressLRS(ELRS) 2.4G from WREKD Co.

NewBeeDrone BeeBrain BLV4 AIO Flight Controller  ExpressLRS(ELRS) 2.4G

NewBeeDrone BeeBrain BLV4 AIO Flight Controller ExpressLRS(ELRS) 2.4G

The BeeBrain BLV4 AIO Flight Controller integrates an F411 flight controller, a 12AMP 4-In-1 BLHeli_S ESC, a 5.8GHz VTX, and an ELRS receiver onto a compact 29x29mm platform.

NewBeeDrone BeeBrain BLV4 AIO - F411 FC + 12A 1-2S BLHeli_S ESC + Built-In ELRS 2.4GHz

Processor (MCU)

The FC is the brain or the CPU of your quad. It has a processor and other components that allow it to listen to your inputs and tells the quad what to do. FCs are commonly sold together with other components integrated or stacked (like ESCs and video transmitters). For beginners, choose a FC with a F4 or F7 processor that has a compatible mount with your frame. 

Flight Controllers

FC Stack Mount

Built-in VTX

Built-in ESC

HGLRC

HGLRC SPECTER F722 Mini 2-6S 20x20 Flight Controller

The HGLRC SPECTER F722 Mini 2-6S 20x20 Flight Controller boasts a powerful STM32F722 processor with up to 216 MHz of computing power for more seamless control, improved feel, and fast response times. It also features a high-performance MPU6000 gyroscope with 42688 pads for optimum stability and a 16MB black box for plenty of flight data storage. Plus, bluetooth parameter adjustment with the SpeeyBee APP allows you to adjust serial port, PID and other flight control parameters anytime and anywhere. There&#39s even a 10V electronic switch for hassle-free power-on/off and nano-scale coating on both sides to protect against water, moisture, and corrosion.
Interested in the HGLRC F760 Mini F722 3-6S 20x20 Stack/Combo (F7 FC / G071 32Bit 60A 4in1 ESC) - MPU6000? 
Interested in just the HGLRC SPECTER G071 128K 32Bit 60A 3-6S 20x20 4in1 ESC? 
Check out all our 20x20 FCs, and all of our HGLRC products!

Specifications
HGLRC SPECTER F722 mini FC

FC Firmware: HGLRC F722 Mini
MCU: STM32F722
Gyro: MPU6000
OSD: AT7456E
Barometer: BMP280
Blackbox 16MB
UARTS:5
Input Voltage: 7.4V-22.8V/2-6S LiPO
BEC: 10V2A/5V2.5A
Size: 37mmx34mmx9.8mm
Mounting: 20x20, M3
Weight: 18g

Includes

1x HGLRC SPECTER F722 mini flight controller

1x 30AWG 25mm double-ended SH1.0-8P cable

1x 30AWG 70mm single-head SH1.0-7P/single-head SH1.0-6P DJI cable

1x 30AWG 70mm single-head SH1.0-7P/single-head GH1.25-6P VTX cable

1x 30AWG 60mm single-head SH1.0-3P/single-head 1.25-3P camera cable

1x 30AWG 100mm single-head SH1.0-4P receiver cable

4x M3x20 hexagon socket screws


The HGLRC SPECTER F722 Mini 2-6S 20x20 Flight Controller boasts a powerful STM32F722 processor with up to 216 MHz of computing power for more seamless control, improved feel, and fast response times. It also features a high-performance MPU6000 gyroscope with 42688 pads for optimum stability and a 16MB black box for ple

HGLRC SPECTER F722 Mini 2-6S 20x20 Flight Controller - MPU6000 from WREKD Co.

HGLRC SPECTER F722 Mini 2-6S 20x20 Flight Controller - MPU6000

The HGLRC Specter F722 Mini HD Flight Controller - MPU6000 is a culmination of over a year's technology development, offering an optimized design and improved circuitry for a refined flying experience.

HGLRC Specter F722 Mini HD Flight Controller - MPU6000 - 20x20

The HGLRC SPECTER F722 Mini 2-6S 20x20 Flight Controller boasts a powerful STM32F722 processor with up to 216 MHz of computing power for more seamless control, improved feel, and fast response times. It also features a high-performance MPU6000 gyroscope with 42688 pads for optimum stability and a 16MB black box for plenty of flight data storage. Plus, bluetooth parameter adjustment with the SpeeyBee APP allows you to adjust serial port, PID and other flight control parameters anytime and anywhere. There's even a 10V electronic switch for hassle-free power-on/off and nano-scale coating on both sides to protect against water, moisture, and corrosion.
Interested in the HGLRC F760 Mini F722 3-6S 20x20 Stack/Combo (F7 FC / G071 32Bit 60A 4in1 ESC) - MPU6000? 
Interested in just the HGLRC SPECTER G071 128K 32Bit 60A 3-6S 20x20 4in1 ESC? 
Check out all our 20x20 FCs, and all of our HGLRC products!

Specifications
HGLRC SPECTER F722 mini FC

FC Firmware: HGLRC F722 Mini
MCU: STM32F722
Gyro: MPU6000
OSD: AT7456E
Barometer: BMP280
Blackbox 16MB
UARTS:5
Input Voltage: 7.4V-22.8V/2-6S LiPO
BEC: 10V2A/5V2.5A
Size: 37mmx34mmx9.8mm
Mounting: 20x20, M3
Weight: 18g

Includes

1x HGLRC SPECTER F722 mini flight controller

1x 30AWG 25mm double-ended SH1.0-8P cable

1x 30AWG 70mm single-head SH1.0-7P/single-head SH1.0-6P DJI cable

1x 30AWG 70mm single-head SH1.0-7P/single-head GH1.25-6P VTX cable

1x 30AWG 60mm single-head SH1.0-3P/single-head 1.25-3P camera cable

1x 30AWG 100mm single-head SH1.0-4P receiver cable

4x M3x20 hexagon socket screws


HGLRC SPECTER F722 4-6S AIO Flight Controller - 40A 8Bit 4in1 ESC

The HGLRC Specter F722 4-6S AIO Whoop/Toothpick Flight Controller (w/ 40A 8Bit 4in1 ESC) comes with an STM32F722 processor, MPU6000 gyroscope, a camera, receiver, and HD/analog direct plug-in interface. Friendly and approachable, it&#39s designed to make your flying experience the best.























Check out all of our HGLRC products and all our whoop flight controllers.
Features

Equipped with MPU6000 gyroscope
Camera, receiver, HD/ analog two-in-one direct plug interface
Supports GPS
Supports Bluejay


Specifications

Product name: SPECTER 40A 4-6S AIO

MCU: STM32F722

MPU: MPU6000

BEC: 5V2A

OSD: Support

LED: Support

Bee Narrator: Support

Continuous current: 40A

Peak current: 50A (10S)

Electrochemical protocol: DSHOT600, Oneshot, Multishot

Flying control firmware: HGLRCF722AIO

Electrochemical firmware: BLS (Bluejay 96K)

ESC: 8Bit

Input voltage: 4-6S 14.8V-22.2V (lipo)

Size: 34x34mm

Install holes: 25.5x25.5mm - M2

Weight: 9.8g

Include

1x HGLRC Specter F722 4-6S AIO Whoop/Toothpick Flight Controller (w/ 40A 8Bit 4in1 ESC) - MPU6000 


The HGLRC Specter F722 4-6S AIO Whoop/Toothpick Flight Controller (w/ 40A 8Bit 4in1 ESC) comes with an STM32F722 processor, MPU6000 gyroscope, a camera, receiver, and HD/analog direct plug-in interface. Friendly and approachable, it's designed to make your flying experience the best. Check out all of our HGLRC products

HGLRC SPECTER F722 4-6S AIO Whoop/Toothpick Flight Controller (w/ 40A 8Bit 4in1 ESC) - MPU6000 from WREKD Co.

HGLRC SPECTER F722 4-6S AIO Whoop/Toothpick Flight Controller (w/ 40A 8Bit 4in1 ESC) - MPU6000

The HGLRC Specter F722 4-6S AIO Whoop/Toothpick Flight Controller (w/ 40A 8Bit 4in1 ESC) comes with an STM32F722 processor, MPU6000 gyroscope, a camera, receiver, and HD/analog direct plug-in interface. Friendly and approachable, it's designed to make your flying experience the best.























Check out all of our HGLRC products and all our whoop flight controllers.
Features

Equipped with MPU6000 gyroscope
Camera, receiver, HD/ analog two-in-one direct plug interface
Supports GPS
Supports Bluejay


Specifications

Product name: SPECTER 40A 4-6S AIO

MCU: STM32F722

MPU: MPU6000

BEC: 5V2A

OSD: Support

LED: Support

Bee Narrator: Support

Continuous current: 40A

Peak current: 50A (10S)

Electrochemical protocol: DSHOT600, Oneshot, Multishot

Flying control firmware: HGLRCF722AIO

Electrochemical firmware: BLS (Bluejay 96K)

ESC: 8Bit

Input voltage: 4-6S 14.8V-22.2V (lipo)

Size: 34x34mm

Install holes: 25.5x25.5mm - M2

Weight: 9.8g

Include

1x HGLRC Specter F722 4-6S AIO Whoop/Toothpick Flight Controller (w/ 40A 8Bit 4in1 ESC) - MPU6000 


HGLRC SPECTER F722 4-6S AIO Whoop/Toothpick Flight Controller (w/ 40A 

The HGLRC Specter 40A 4-6S AIO - MPU6000 is a high-performance all-in-one flight controller, integrating advanced control and gyroscopic features.

HGLRC Specter AIO - F722 FC + 40A 4-6S ESC - MPU6000

T-Motor

T-Motor Velox F7 SE 3-6S 30x30 Flight Controller

Tiger Motors

Introducing the T-Motor Velox F7 SE Flight Controller, engineered for precision and performance in aerial applications.&nbsp

Introducing the T-Motor Velox F7 SE Flight Controller, engineered for precision and performance in aerial applications. 

T-Motor Velox F7 SE Flight Controller

TMOTOR

Experience the full functionality of VELOX F7 SE flight controller. Enhanced safety with Betaflight wiring standard. Precise control, seamless compatibility, and wireless parameter adjustment. Upgrade your FPV experience now!
Browse our 30x30 Flight Controllers and all our T-Motor products!
Features

Experience the full functionality of VELOX F7 SE flight controller. Enhanced safety with Betaflight wiring standard. Precise control, seamless compatibility, and wireless parameter adjustment. Upgrade your FPV experience now!
Simplified Wire Order: VELOX F7 SE flight controller ensures easy and standardized wire connections, compatible with V50A SE ESC.
Enhanced Performance: Experience stable flight with low latency using the second-generation power solution.
Wireless Bluetooth Control: Adjust settings wirelessly using SpeedyBee software on your mobile phone, eliminating the need for cables.
Ample Memory Capacity: 128M storage, allowing for efficient recording of flight data.
Versatile Solder Pads: Conveniently connect various devices without soldering, including video receivers, cameras, LEDs, and GPS.
Multi-Motor Control: Control up to 8 motors for diverse configurations, expanding the capabilities of your drone.


 
Specifications

 Firmware: STM32F7X2
Unified Target: TMTR-TMOTOR VELOX F7
MCU: STM32F722
Gyroscope: IMC-42688-P(SPI)
BEC: 5V2A &amp 12V1.5A
Uarts: 6
Bluetooth: TMFC
OSD: AT7456E&ampHD
Black Box: 128MB
USB: Type C
Weight: 9g
Size: 37.5x40x6.4mm
Installation Hole: 30.5x30.5/⌀4mm
Input voltage: 12-27V(3-6S)
Typical application: 170-450multi-rotor

Includes
1x T-Motor Velox F7 SE 3-6S 30x30 Flight Controller

Experience the full functionality of VELOX F7 SE flight controller. Enhanced safety with Betaflight wiring standard. Precise control, seamless compatibility, and wireless parameter adjustment. Upgrade your FPV experience now! Browse our 30x30 Flight Controllers and all our T-Motor products! Features Experience the full

Diatone

Diatone Mamba F722 APP MK4 30x30 Flight Controller

The Diatone Mamba MK4 is an F722 flight controller. With WiFi capabilities through the SpeedyBee APP, this stack is the perfect addition to your FPV build. This version has an IMC42688P Gyro.

Diatone MAMBA MK4 F722 APP (WiFi) Flight Controller - ICM42688P

DiatoneUSA





The Diatone Mamba MK4 is an F722 flight controller. With WiFi capabilities through the SpeedyBee APP, this stack is the perfect addition to your FPV build. This version has an IMC42688P Gyro.





Check out all our 30x30 FCs and all our Diatone Gear!




Specifications





MCU: STM32F722
GYRO: IMC42688P
Barometer: Yes
OSD: Yes
Blackbox: 16M Flash Memory
Uarts: 6Set
ESC Telemetry: Yes
Power Led: Yes
LED Controller: BF LED/MB LED

F.Port: Yes
RSSI: Yes
Buzz: Yes
Input: 3-6S Lipo
TVS Protection: Yes
BEC: 3.3V/0.5A, &ampamp 5V/3A, and 9V/3A

Mounting: 30.5x30.5mm, M3


Includes

1x Diatone Mamba DJI F722 APP MK4 30x30 Flight Controller
5x M3 ESC Isolation Dampers
5x M3 Silicone Dampers
1x 6-Pin Air Unit Cable
2x 8-Pin Cable

Wiring Diagram











The Diatone Mamba MK4 is an F722 flight controller. With WiFi capabilities through the SpeedyBee APP, this stack is the perfect addition to your FPV build. This version has an IMC42688P Gyro. Check out all our 30x30 FCs and all our Diatone Gear! Specifications MCU: STM32F722 GYRO: IMC42688P Barometer: Yes OSD: Yes Blac

Diatone Mamba DJI F722 APP MK4 30x30 Flight Controller from WREKD Co.

Diatone Mamba DJI F722 APP MK4 30x30 Flight Controller

Diatone MAMBA MK4 F722 APP Flight Controller - 30x30mmCheck out all our 30x30 Flight Controllers and our full Diatone collection!. Package Includes:  1 x Diatone MAMBA MK4 F722 APP Flight Controller - 30x30mm

Diatone MAMBA MK4 F722 APP Flight Controller - 30x30mm








The Diatone Mamba MK4 is an F722 flight controller. With WiFi capabilities through the SpeedyBee APP, this stack is the perfect addition to your FPV build. This version has an IMC42688P Gyro.





Features


30.5 x 30.5mm Mounting Pattern
16M Flash Memory Blackbox
3~6S Lipo (12.6~25.2V) Input
WiFI SpeedyBee Capabilities
MAMBA MK4 F722 APP FC
ICM42688P GYRO
6 Uarts
Buzzer
OSD











Specifications


Receiver: TBS/SBUS/|IBUS/DSM
Mounting: 30.5x 30.5mm/M3
Receiver Protection: Yes
Blackbox: 16M Memory
Size: 38.0x40.5x8mm
WIFI: SpeedyBee APP
Frequency: 216MHz
Software: Betaflight
BEC Protection: Yes
TVS Protection: Yes
AIR UNIT Port: Yes
MCU: STM32F722
Gyro: IMC42688P
ESC Signal: 8 Set
Buzzer Pad: Yes
VTX Switch: Yes
OSD: AT 7456E
BEC 3.3V: 0.5A
CURR Pad: Yes
Input: 6S Lipo
MB LED: Yes
Weight: 10g
BF LED: Yes
Uarts: 6 Set
BEC 9V: 3A
BEC 5: 3A
F.Port: Yes
12C: Yes






Includes


1x Diatone MAMBA MK4 F722 APP (WiFi) Flight Controller - IMC42688P
5x M3 ESC Isolation Dampers
5x M3 Silicone Dampers
1x 6-Pin Air Unit Cable
2x 8-Pin Cable




















The Diatone Mamba MK4 is an F722 flight controller. With WiFi capabilities through the SpeedyBee APP, this stack is the perfect addition to your FPV build. This version has an IMC42688P Gyro. Features 30.5 x 30.5mm Mounting Pattern 16M Flash Memory Blackbox 3~6S Lipo (12.6~25.2V) Input WiFI SpeedyBee Capabilities MAMBA

MAMBA MK4 F722 APP Flight Controller 30mm/M3

DIATONE





The Diatone Mamba MK4 is an F722 flight controller. With WiFi capabilities through the SpeedyBee APP, this stack is the perfect addition to your FPV build. This version has an IMC42688P Gyro.





Check out all our 30x30 FCs and all our Diatone Gear!




Specifications





MCU: STM32F722
GYRO: IMC42688P
Barometer: Yes
OSD: Yes
Blackbox: 16M Flash Memory
Uarts: 6Set
ESC Telemetry: Yes
Power Led: Yes
LED Controller: BF LED/MB LED

F.Port: Yes
RSSI: Yes
Buzz: Yes
Input: 3-6S Lipo
TVS Protection: Yes
BEC: 3.3V/0.5A, &amp 5V/3A, and 9V/3A

Mounting: 30.5x30.5mm, M3


Includes

1x Diatone Mamba DJI F722 APP MK4 30x30 Flight Controller
5x M3 ESC Isolation Dampers
5x M3 Silicone Dampers
1x 6-Pin Air Unit Cable
2x 8-Pin Cable

Wiring Diagram











RDQ Bardwell F7 V2 3-6S 30x30 Flight Controller - JBF7 V2

IFLIGHT







The new JBF7 V2 takes everything great about the original JBF7 and adds a few key features that you asked for. Just like the original, it's got an F7 processor, SD card slot for black box logging, and 8 motor outputs. It's got a flexible pad layout that can handle almost any combination of peripherals you could want. Pads are large and heavy--easy for beginners to solder to and reduce the risk of lifted pads. With the new JBF7 V2, we switched to USB-C we added a VTX pit switch we added plugs for all of the major features, and we included pre-made plugs for common peripherals, to allow a no-solder or less-solder build for people using those peripherals. We also added small status LEDs for major components, to make troubleshooting easier. For those who like autonomous flight, the board now includes a barometer.







Check out all our 30x30 FCs and the full range of RDQ Products!

If you have any issues accessing the Black Box features please type out this text in the CLI to get black box data to your SD card "set sdcard_detect_inverted=on" press ENTER, then type "save" and press ENTER.
Features 


Manual written and feature set selected by Joshua Bardwell.
Board layout focused on flexibility and resilience. You can build what you want, how you want, without stress.
ESC 4-in-1 plug also has solder pads, for troubleshooting, or if you want to direct-solder the ESC.
Plug-and-play support for DJI Air Unit. Voltage regulator allows up to 6S input.
Eight motor pads for easy resource remapping or for that octo cinelifter you're thinking of building.
SD card slot for blackbox logging.
All major functions available in SH plugs, and pre-made wire set included for most common peripherals
USB-C plug
VTX pit switch built-in (9v rail only) allows you to power down the video transmitter using a controller switch

Barometer on board (no iNav target at release date, but possible for the future)
Status LEDs for major components allow easier troubleshooting
9v regulator rated for 3A. Verified to power HDZero Freestyle and DJI VTX.


Joshua Bardwell's Comprehensive Manual 
Specifications

Input Voltage: 3-6S LiPo
MCU: STM32F722
Gyro: BMI270

Barometer: DPS310
Power Outputs: 5V 3A, 9V 3A (w/ Pit Switch), 3.3V, vBat
BF Target: JBF7 V2

UARTs: 5 (I2C SDA/SCL shared with UART 3)

Plugs: 4in1 ESC, RX, Analog Cam, HD Cam, VTX, LED/Buzzer
Mounting Pattern: 30.5x30.5mm
Weight: 8.3g (w/ gummies &amp USB Protector) 


Includes

1x RDQ Bardwell F7 V2 3-6S 30x30 Flight Controller - JBF7 V2
1x 4in1 ESC Cable 
1x DJI Air Unit / HD Camera Cable

1x Analog Camera Cable  

1x Analog VTX Cable
1x LED / Buzzer Cable
1x Receiver Cable
1x USB-C Protector
1x Set of Gummies 


Wiring Diagram
For in depth wiring instructions, see Joshua Bardwell's Comprehensive Manual 



The new JBF7 V2 takes everything great about the original JBF7 and adds a few key features that you asked for. Just like the original, it's got an F7 processor, SD card slot for black box logging, and 8 motor outputs. It's got a flexible pad layout that can handle almost any combination of peripherals you could want. P

Joshua Bardwell







The new JBF7 V2 takes everything great about the original JBF7 and adds a few key features that you asked for. Just like the original, it&#39s got an F7 processor, SD card slot for black box logging, and 8 motor outputs. It&#39s got a flexible pad layout that can handle almost any combination of peripherals you could want. Pads are large and heavy--easy for beginners to solder to and reduce the risk of lifted pads. With the new JBF7 V2, we switched to USB-C we added a VTX pit switch we added plugs for all of the major features, and we included pre-made plugs for common peripherals, to allow a no-solder or less-solder build for people using those peripherals. We also added small status LEDs for major components, to make troubleshooting easier. For those who like autonomous flight, the board now includes a barometer.







Check out all our 30x30 FCs and the full range of Products!

If you have any issues accessing the Black Box features please type out this text in the CLI to get black box data to your SD card &quotset sdcard_detect_inverted=on&quot press ENTER, then type &quotsave&quot and press ENTER.
Features 


Manual written and feature set selected by Joshua Bardwell.
Board layout focused on flexibility and resilience. You can build what you want, how you want, without stress.
ESC 4-in-1 plug also has solder pads, for troubleshooting, or if you want to direct-solder the ESC.
Plug-and-play support for DJI Air Unit. Voltage regulator allows up to 6S input.
Eight motor pads for easy resource remapping or for that octo cinelifter you&#39re thinking of building.
SD card slot for blackbox logging.
All major functions available in SH plugs, and pre-made wire set included for most common peripherals
USB-C plug
VTX pit switch built-in (9v rail only) allows you to power down the video transmitter using a controller switch

Barometer on board (no iNav target at release date, but possible for the future)
Status LEDs for major components allow easier troubleshooting
9v regulator rated for 3A. Verified to power HDZero Freestyle and DJI VTX.


Joshua Bardwell&#39s Comprehensive Manual 
Specifications

Input Voltage: 3-6S LiPo
MCU: STM32F722
Gyro: BMI270

Barometer: DPS310
Power Outputs: 5V 3A, 9V 3A (w/ Pit Switch), 3.3V, vBat
BF Target: JBF7 V2

UARTs: 5 (I2C SDA/SCL shared with UART 3)

Plugs: 4in1 ESC, RX, Analog Cam, HD Cam, VTX, LED/Buzzer
Mounting Pattern: 30.5x30.5mm
Weight: 8.3g (w/ gummies &ampamp USB Protector) 


Includes

1x Bardwell F7 V2 3-6S 30x30 Flight Controller - JBF7 V2
1x 4in1 ESC Cable 
1x DJI Air Unit / HD Camera Cable

1x Analog Camera Cable  

1x Analog VTX Cable
1x LED / Buzzer Cable
1x Receiver Cable
1x USB-C Protector
1x Set of Gummies 


Wiring Diagram
For in depth wiring instructions, see Joshua Bardwell&#39s Comprehensive Manual 



Bardwell F7 V2 3-6S 30x30 Flight Controller - JBF7 V2 from WREKD Co.

Bardwell F7 V2 3-6S 30x30 Flight Controller - JBF7 V2

The Bardwell F7 V2 Flight Controller (JBF7 V2) features an F7 processor, ICM20602 Gyro, several DC power outputs, and 8 motor pads. The V2 now features USB-C, a VTX pit switch, solderless plugs, a barometer, iNav support, and LEDs.

iFlight

iFlight BLITZ F7 Pro V1.1 Flight Controller

The iFlight BLITZ F722 Pro V1.1 flight controller features an improved circuit design, better components, and lower electrical noise. This FC is plug-and-play with DJI and has FC LED indicators, a 512Mb Black box, and an LC filter. 

iFlight BLITZ F7 Pro V1.1 Flight Controller - 35x35 

Zeez

Zeez F7 3030 V3 Flight Controller 

Zeez Design

The ZEEZ F7 V3 3030 is an 8 Motor Output, DJI HD System Ready Flight Controller with an on-board 9V@3A regulator to power the DJI Air Unit, with a simple plug-and-play configuration and 5V@3A regulator to power all the peripheral.

SpeedyBee

SpeedyBee F745 AIO Flight Controller - F745 FC, 35A 3-6S ESC

The SpeedyBee F745 AIO includes an F745 flight controller and a 35A ESC. Featuring a BMP280 barometer, OSD, 8MB Memory Blackbox, and MPU600 Gyro... this AIO board is the perfect addition to your FPV build.

SpeedyBee F745 AIO Board - F745 FC + 35A BLHeli_S 3-6S ESC

Check out all our 30x30mm Stacks and the rest of our SpeedyBee Products! Overview: Product Name SpeedyBee F745 35A BLS AIO Power Input 3S - 6S Lipo Mounting 25.5 x 25.5mm, 3mm hole diameter Dimension 36.5mm(L) x 36.5mm(W) x 7mm(H), recommended for quads at 3.5" or above Weight 10.1g FC Specifications:  MCU STM32F745 IM

SpeedyBee F745 35A BLHeli_S 3-6S AIO Flight Controller/ESC - 25.5x25.5mm

Aikon

Aikon F7 3-6S AIO Flight Controller - 60A 8bit ESC

The Aikon flight controller is a new generation flight controller and ESC combination specifically designed for cinewhoops and other high-current applications. We've packed all the greatest features into one seamless flight experience. Check out all our Whoop Style AIO Boards and the rest of our Aikon Products! Feature

Aikon F7 60A BLHeli_S All-In-One Flight Controller - 25.5x25.5

The Aikon F7 AIO Board - F7 FC + 60A 3-6S BLHeli_S ESC&nbspis a new generation flight controller and ESC combination specifically designed for cinewhoops and other high-current applications. All the greatest features into one seamless flight experience!

The Aikon F7 AIO Board - F7 FC + 60A 3-6S BLHeli_S ESC is a new generation flight controller and ESC combination specifically designed for cinewhoops and other high-current applications. All the greatest features into one seamless flight experie

Aikon F7 AIO Board - F7 FC + 60A 3-6S BLHeli_S ESC

SpeedyBee F7 V3 Flight Controller

RunCam

The SpeedyBee F7 V3 Flight Controller is an F722 FC featuring a BMP280 barometer, OSD, 500MB Memory Blackbox, a built-in FC LiPo monitoring system, and many more features.

NewBeeDrone Infinity V2 F7 3-6S 30x30 AIO Flight Controller - 55A 32Bit ESC

The&nbspNewBeeDrone Infinity AIO V2&nbspis designed to be the board that can last forever. This updated version has optimized hardware and even better weather protection than the V1. This AIO packs in requested features such as OSD Chips and more UART Ports.&nbsp

The NewBeeDrone Infinity AIO V2 is designed to be the board that can last forever. This updated version has optimized hardware and even better weather protection than the V1. This AIO packs in requested features such as OSD Chips and more U

NewBeeDrone Infinity AIO V2 - F745 FC + 55A BLHeli_32 3-6S ESC

NewBeeDrone Infinity AIO V2 Pro is Upgraded from AIO V2. Now it comes with Dual BMI270 Gyro. Better performance on handling noise and better reliability. Any requests from the V1, we have them on the V2.Our first-generation board was fully covered in heatsink and the components were sealed completely to provide better 

NewBeeDrone Infinity AIO V2 Pro F7 BLHeli32 55A AIO Flight Controller - 30x30mm

T-Motor F7 Pro Full Function 30x30 Flight Controller - Wifi, Bluetooth

T-Motor Hobby

T-Motor has come out with one of the most advanced F7 flight controllers on the market. With 8 motor outputs, built-in Wi-Fi and Bluetooth, this FC is ready to take on even the most demanding of FPV tasks.
Browse our 30x30 Flight Controllers and all our T-Motor products!

Features

Wi-Fi
Bluetooth
Built-in blackbox for data logging
8 PWM outputs
DJI air unit plug

Specifications

MCU: STM32F722 RET6
IMU: BMI270
Barometer: BMP280
Input Voltage: 3-8S
BEC: 10V/2A, 5V/3A
OSD: AT7456
Blackbox: 16MB Flash
Motor Outputs: 8
UARTS: 6
Target: TMOTOR F7 V2
Dimensions: 37x37x7.5mm
Mounting Pattern: 30x30mm
Weight: 8.1g

Includes

1x T-Motor F7 Pro Full Function 30x30 Flight Controller







T-Motor has come out with one of the most advanced F7 flight controllers on the market. With 8 motor outputs, built-in Wi-Fi and Bluetooth, this FC is ready to take on even the most demanding of FPV tasks. Browse our 30x30 Flight Controllers and all our T-Motor products! Features Wi-Fi Bluetooth Built-in blackbox for d

T-Motor F7 Pro Full Function 30x30 Flight Controller w/ Wifi & Bluetooth from WREKD Co.

T-Motor F7 Pro Full Function 30x30 Flight Controller w/ Wifi & Bluetooth

T-Motor has come out with one of the most advanced F7 flight controllers on the market. With 8 motor outputs, built-in Wi-Fi and Bluetooth, this FC is ready to take on even the most demanding of FPV tasks.
Browse our 30x30 Flight Controllers and all our T-Motor products!

Features

Wi-Fi
Bluetooth
Built-in blackbox for data logging
8 PWM outputs
DJI air unit plug

Specifications

MCU: STM32F722 RET6
IMU: ICM42688
Barometer: BMP280
Input Voltage: 3-8S
BEC: 10V/2A, 5V/3A
OSD: AT7456
Blackbox: 16MB Flash
Motor Outputs: 8
UARTS: 6
Target: TMOTOR F7 V2
Dimensions: 37x37x7.5mm
Mounting Pattern: 30x30mm
Weight: 8.1g

Includes

1x T-Motor F7 Pro Full Function 30x30 Flight Controller







The T-Motor F7 Pro Full Function 30x30 Flight Controller w/ Wifi & Bluetooth is a high performance FC packed with features and convenience. This powerful FC is ready for anything.

T-Motor F7 Pro Full Function 30x30 Flight Controller w/ Wifi & Bluetooth for Sale

T-Motor's F7 Pro flight controller has arrived! This flight controller is full featured and designed with Cinelifter quads in mind. It has eight PWM outputs all on one convenient connector and is plug and play with the DJI Air Unit using the included cable. The flight controller has built in Wi-Fi and Bluetooth so you 

T-Motor F7 Pro Flight Controller - 30x30mm

T-Motor's F7 Pro Flight Controller has arrived! Enjoy full function in a wireless state! Great for cinematic professional use. This FC features 8 UARTS, WiFi and Bluetooth capabilites, and a 30.5x30.5 mounting pattern.Now with ICM42688 gyro.

T-Motor's F7 Pro Flight Controller has arrived! Enjoy full function in a wireless state! Great for cinematic professional use. This FC features 8 UARTS, WiFi and Bluetooth capabilites, and a 30.5x30.5 mounting pattern.
Now with ICM42688 gyro.

T-Motor F7 PRO Flight Controller w/ WiFi + Bluetooth

SpeedyBee F7 Mini 35A 3-6S 20x20 Flight Controller Stack - F7 FC, 35A 8Bit ESC

The ultimate 20x20 stack for on the go tuning! With integrated bluetooth, this stack allows you to access Betaflight and even BLHeli through the Speedy Bee app.
Check our other Stacks and our SpeedyBee products! 
Specifications
SpeedyBee F7 Mini

Input Voltage: 3-6S
MCU: STM32F722
Gyro: BMI270 

Barometer: No
OSD Chip: AT7456E
Bluetooth: Yes
DJI Air Unit Soldering Pads: Supported
BlackBox: 8MB Flash
Current Sensor: Yes
BEC: Yes
ESC Signal Pads: 4
UARTs: 3(UART1, UART2, UART3)
ESC Telemetry: R4(UART4)
LED Pad: Used for WS2812 LED
Buzzer: Yes
Firmware: BetaFlight(Default), EMUFlight, INAV
Firmware Target: SPEEDYBEEF7MINI
Mounting Dimensions: 20 x 20mm, 3.5mm hole diameter
Weight 5.7g

SpeedyBee 35A BLHeli_S ESC

Power Input: 3-6S
Firmware: BLHeli_S JH40
Max Continuous Current: 35A
Max Burst Current: 45A
ESC Protocol: DSHOT300/600
Current Sensor: Yes
Mounting Dimensions: 20 x 20mm, 3.6mm hole diameter
Weight: 7g

Includes

1x SpeedyBee F7 Mini 35A 3-6S 20x20 Stack/Combo


The ultimate 20x20 stack for on the go tuning! With integrated bluetooth, this stack allows you to access Betaflight and even BLHeli through the Speedy Bee app. Check our other Stacks and our SpeedyBee products!  Specifications SpeedyBee F7 Mini Input Voltage: 3-6S MCU: STM32F722 Gyro: BMI270 Barometer: No OSD Chip: AT

SpeedyBee F7 Mini 35A 3-6S 20x20 Stack/Combo (F7 FC / 35A 8bit 4in1 ESC) from WREKD Co.

SpeedyBee F7 Mini 35A 3-6S 20x20 Stack/Combo (F7 FC / 35A 8bit 4in1 ESC)

Introducing SpeedyBee's new 20x20mm flight controller and ESC stack. Now featuring a 20x20mm version of their F7 Flight Controller with onboard Bluetooth tuning options available via the SpeedyBee app. Plus a true 35A Electronic Speed Controller! No BS, they even have video proof to back up their claims. The ESC also c

SpeedyBee F7 Mini Stack w/ 35A 3-6S 8-bit ESC - 20x20mm

The popular SpeedyBee F7 stack has shrunk into a mini 20x20 stack! With the same features as wireless FC and ESC tuning, change motor directions and more through the SpeedyBee app!

SpeedyBee F7 Mini 35A 3-6S 8-bit Flight Controller Stack

RUNCAM

SpeedyBee F7 Mini 35A 3-6S 20x20 Stack/Combo (F7 FC / 35A 8bit 4in1 ES

HAKRC

HAKRC F722 2-6S AIO Whoop/Toothpick Flight Controller - 40A 8Bit ESC, External USB Board

HAKRC bring us another serious contender in whoop sized AIO boards. With an F722 flight controller and 40 Amp ESC on board, this AIO is sure to keep even the most powerful quads flying well. This AIO also features both internal and external USB.
Check out our other AIO boards and maybe even some nice motors to finish off your build.
Features

The PCB adopts high-end 8-layer 2oZ thick copper skin, which has stronger over-current capability and good heat dissipation

MOS adopts imported 40V high current resistance MOS, long life and strong load capacity
Industrial grade LDO, high temperature resistance

High-quality Japanese Murata capacitors, strong filtering performance
Internal and External USB


Specifications
Flight Controller

Input Voltage: 2S-6S
MCU: STM32F722RET6
IMU: MPU6000
OSD: AT7456E
UARTs: 5
Flight control firmware version: HAKRC F722D
BEC: 5V/3A
Sensor: Built-in current sensor
Barometer: integrated
LED: Support WS2812 and other programmable
Compatible receivers: CRSF / Frsky/ Futaba/ Flysky/TBS Crossfire/ DSMX: DSM2 receiver
Dimensions: 32x32mm (25.5mm-26.5mm mounting hole)

ESC

Input voltage: 2S-6S
Continuous current: 40A
Peak current: 50A
Firmware version: BLHELI _S (G- H-30)
Current meter proportional value: 450

Protocol support: PWM, Oneshot125, Oneshot42,Multishot, Dshot150, Dshot300, Dshot600



Includes


1x HAKRC F722 AIO Whoop/Toothpick Flight Controller w/ 2-6S 8Bit 40A ESC
1x XT30 power cord
1x Type-C USB small board
1x SH1.0/7P single-head cable
1x 270uf/35V capacitor
4x Yellow shock-absorbing balls


Wiring Diagram


HAKRC bring us another serious contender in whoop sized AIO boards. With an F722 flight controller and 40 Amp ESC on board, this AIO is sure to keep even the most powerful quads flying well. This AIO also features both internal and external USB. Check out our other AIO boards and maybe even some nice motors to finish o

HAKRC F722 2-6S AIO Whoop/Toothpick Flight Controller w/ 8Bit 40A ESC & External USB Board from WREKD Co.

HAKRC F722 2-6S AIO Whoop/Toothpick Flight Controller w/ 8Bit 40A ESC & External USB Board

HAKRC F722 2-6S AIO Whoop/Toothpick Flight Controller w/ 8Bit 40A ESC 

The F722 40A AIO is HakRC's new whoop style flight controller/ESC AIO board for ultralite and whoop build.This FC features an onboard as well as external USB port for thos tight build where it's hard to reach the USB plug.Checkout all our Whoop Style Flight Controllers and the rest of our HAKRC products! Features: The 

HAKRC F722 2-6S 40A AIO FLIGHT CONTROLLER BLHELI_S(W/external USB Board)

This&nbspHAKRC AIO Board&nbspfeatures a brushless F722 flight controller and a 40A 2-6S BLHeli_S ESC. This version carries an external USB. This is an ultra-light 7g brushless AIO flight controller!!&nbspThis FC has a strong performance and can handle 40A continuous current and up to 6S.&nbsp

This HAKRC AIO Board features a brushless F722 flight controller and a 40A 2-6S BLHeli_S ESC. This version carries an external USB. This is an ultra-light 7g brushless AIO flight controller!! This FC has a strong performance and can ha

HAKRC AIO Board - Brushless F722 FC + 40A 2-6S BLHeli_S ESC w/ External USB

T-Motor Mini Racer F7 20x20 Flight Controller

The&nbspT-Motor Mini Racer F7&nbspis a 3-6S 20x20 mini flight controller with a 16MB Blackbox flash memory, 5V.2A BEC, and an MPU6000 gyro. Designed for easy maintenance and low interference.&nbsp

The T-Motor Mini Racer F7 is a 3-6S 20x20 mini flight controller with a 16MB Blackbox flash memory, 5V.2A BEC, and an MPU6000 gyro. Designed for easy maintenance and low interference. 

T-Motor Mini Racer 20x20 F7 Flight Controller

T-Motor enters the world of Flight Controllers yet again with another that is sure to impress! 
Check out all our 20x20 FCs and all our T-Motor products!
Specifications

Input Voltage: 3-6S
MCU: STM32F722RET6
OSD: AT7456E
Uarts: 4
BEC: 5V/2A(Peak 2.5A)
Blackbox: 16MB
Gyro: BMI270
Dimensions: 31*30mm
Stack Size: 20*20mm

Includes

1x T-Motor Mini Racer F7 20x20 Flight Controller





Wiring Diagram


T-Motor enters the world of Flight Controllers yet again with another that is sure to impress!  Check out all our 20x20 FCs and all our T-Motor products! Specifications Input Voltage: 3-6S MCU: STM32F722RET6 OSD: AT7456E Uarts: 4 BEC: 5V/2A(Peak 2.5A) Blackbox: 16MB Gyro: BMI270 Dimensions: 31*30mm Stack Size: 20*20mm 

The new T-Motor F7 Racer FC is designed specifically for thight builds such as race frames, The front portion of the FC is recessed to provide clearance for the FPV Camera.Check out the 20x20mm Flight Controllers and all our T-Motor Products!     Specifications Input Voltage: 3-6S MCU: STM32F722RET6 OSD: AT7456E Uarts:

T-Motor Mini Racer F7 Flight Controller - 20x20mm

T-Motor Mini Racer F7 20x20 Flight Controller from WREKD Co.

GEPRC

GEPRC F722 AIO Flight Controller - F722 FC, 35A 2S-6S ESC

The GEPRC F722 AIO is equipped with an F722 FC and 35A 2S-6S BLS ESC. This AIO stack adopts MCU STM32F722, which gives a powerful performance and higher computing speed. It features 5 full UART ports and can connect more external devices. GEPRC designed a 6-pin connector for the DJI Air Unit, just plug and play.
The BLheili_S 35A ESC can handle 35A continuous current (40A burst), supports 2-6S lipo batteries, and brings the drone a stronger flight performance. Support OSD parameter adjustment, buzzer, led, and other functions. It is 8.8g, ultra-lightweight, and 25.5x25.5mm mounting hole, suitable for most of the frames on the market!
Check out all our whoop flight controllers, and our GEPRC products!
Features

MCU: STM32F722, with strong performance and higher computing speed.
It has 5 full UART ports, which connect more external devices
6-pin connector for DJI Air Unit module, and just plug and play.
The BLheili_S 35A ESC can handle 35A continuous current (40A burst).
Support OSD parameter adjustment, buzzer, led, and other functions.
8.8g ultra-lightweight
25.5x25.5mm mounting hole, suitable for most frames

Specifications
GEPRC F722 AIO

Model Name: GEP-F722-35A AIO
MCU: STM32F722
IMU: BMI270/42688
Firmware target: GEPRC_F722_AIO
OSD: Betaflight OSD w/ AT7456Ev
UART Ports: R1 T1 / R2 T2 / R3 T3 / R4 T4 / R5 T5
Beeper: YES
LED: YES
USB: Micro USB
BEC output: 5V@1A
Integrated LC Filter
ESC MCU: 8BB21F16G
Continuous current: 35A
MAX current: 40A (10s)
Input: 2-6S
Supports: Dshot600, Oneshot, Multishot
BlackBox: 16Mb
Target: G_H_30
Size: 32x32mm Board
Installing Hole: 25.5x25.5mm, M2
Weight: 8.8g


Includes

1x GEP-F7-35A AIO
1x XT30-7CM-18AWG Power cables
1x 35V220UF capacitance
1x SH1.0-6Pin to GH1.25-8Pin cables
8x M2*6.5mm Damping ring


The GEPRC F722 AIO is equipped with an F722 FC and 35A 2S-6S BLS ESC. This AIO stack adopts MCU STM32F722, which gives a powerful performance and higher computing speed. It features 5 full UART ports and can connect more external devices. GEPRC designed a 6-pin connector for the DJI Air Unit, just plug and play. The BL

GEPRC F722 2-6S F7 AIO FC w/ 35A 8Bit 4in1 ESC from WREKD Co.

GEPRC F722 2-6S F7 AIO FC w/ 35A 8Bit 4in1 ESC

The GEPRC F722 AIO is equipped with an F722 FC and 35A 2S-6S BLS ESC. This AIO stack adopts MCU STM32F722, which gives a powerful performance and higher computing speed.

GEPRC F722 AIO - F722 FC+ 35A 2S-6S BLS ESC

Model Name：GEP-F722-35A AIO
 	MCU:STM32F722
 	IMU:BMI270/42688 gyro/accelerometer(SPI)
 	OSD:Betaflight OSD w/ AT7456Ev
 	BEC output：5V@1A
 	Intergrated LC Filter
 	ESC MCU：BB21F16G
 	Continuous current：35A
 	Input：2~6S
 	Supports：Dshot600,Oneshot,Multishot
 	Size：32x32mm Board
 	Mounting Hole：25.5x25.5mm
 	Weight：8.8g

Model Name：GEP-F722-35A AIO  MCU:STM32F722  IMU:BMI270/42688 gyro/accelerometer(SPI)  OSD:Betaflight OSD w/ AT7456Ev  BEC output：5V@1A  Intergrated LC Filter  ESC MCU：BB21F16G  Continuous current：35A  Input：2~6S  Supports：Dshot600,Oneshot,Multishot  Size：32x32mm Board  Mounting Hole：25.5x25.5mm  Weight：8.8g

GEP-F722-35A AIO (F722 FC 35A 2-6S 8bits BLS ESC 25.5mm) - GEPRC

GEP-F722-35A AIO (F722 FC 35A 2-6S  8bits BLS ESC 25.5mm)

Hobbywing

Hobbywing XRotor F722 3-6S 30x30 Flight Controller Stack - F7 FC, 60A 32Bit ESC

HOBBYWING












The Hobbywing XRotor F722 Stack/Combo packs in the latest tech: 65A (x4) ESCs, BLHeli_32 DShot 1200 support, two 5V BECs, plus a voltmeter module that lets your FC know your battery's voltage and amperage in real-time! The F7 Flight Controller offers OSD, voltage monitoring, two BECs, and an interface for the DJI image transmission system. Build the perfect multirotor with this feature-packed, powerful combo! 











Check out all our 30x30 stacks &amp combos, and our Hobbywing selection!

Features


Manual for the FC

Manual for the ESC


XRotor 65A 4in1 ESC


High performance 32-bit microprocessor with the running frequency of up to 120MHz for excellent performance.


Third generation BLHeli_32 code can support up to 128KHz PWM output frequency, which can be compatible with more motors.


All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling.


Code supports features to prevent sync loss. There are tunable parameters that can make the code run well even in the most demanding situations, although default settings will work excellently in normal operating environments.


The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multishot (5-25us).


Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power up.


Also supports a beacon functionality, where the ESC will start beeping after a given time of zero throttle. This can be very useful for finding lost aircraft.


F7 Flight Controller Features


STM32 F722 MCU allows the FC to run the PID looptime and gyro with higher frequency.


Onboard OSD microchip which supports the DMA mode allows users to adjust its parameters via the Betaflight software. (Note: the OSD is controlled by the F4 MCU.)


The FC supports Betaflight firmware and allows parameter adjustment via Betaflight software is more applicable to FPV racing.


Onboard Flash chip can record and save flight/black box data allowing users to adjust the setup of their aircraft easily.


Compatible with various receivers like SBUS, SUMH, SUMD, SPEKTRUM1024/2048, XBUS and etc.


LED strip signal output port allows users to adjust the color and flash mode of the LED strip via the FC.


Volt/Amp monitoring port allows users to check the battery voltage (BAT port) and current (CRT port, extra current meter is needed).


Buzzer output port allows users to connect external buzzer(s) to the FC for warning or informing the flight status of the aircraft.


Micro USB port allows users to connect the FC to a PC to flash firmware and adjust parameters.

Board load 5V and 10V BEC, both can output 2A. It can supply power for receiver, VTX, LED lamp and others devices.


 Specifications

XRotor F7 FC

Compatible with (Multirotors) Quadcopters

Firmware HOBBYWING_XROTORF7CONV

FC Programming Supported

Programming via Betaflight/ Cleanflight-configurator

Compatible with (Modes) PWM, Oneshot125, Oneshot42, Multishot, Dshot150,
Dshot300, Dshot600, PROSHOT1000

Compatible with (Transmitters) PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL
OSD Built-in

Voltage Monitoring Supported

Current Monitoring Supported

External Buzzer Supported

LED Control Supported

BEC 5V @ 1.5A  10V @ 1.5A

Size 32x32mm

Weight 3.3g

XRotor 65A BLHeli_32 ESC

LiPo Power input: 3-6S

Cont.Current: 65Ax4

Burst Current: 80Ax4

BEC Output: 5V@ 0.5A 

Input wires: 12AWG-130mm* (Red/Black)

Output Wire: No wires but solder tabs

Connectors: (In/Out) XT60 (w/ Wires Soldered on) /no

Weight / Size: 15.0g / 32.7x18.4x6.2mm

Mounting holes: 30.5x30.5mm

Throttle Calibration: Supported

ESC Programming: BLHeliSuite32

Includes

1x Hobbywing XRotor F722 3-6S 30x30 Stack/Combo (F7 FC / 32Bit 65A 4in1 ESC)
1x Hardware Set
1x AMASS XT60 Connector
1x Cable Set


The Hobbywing XRotor F722 Stack/Combo packs in the latest tech: 65A (x4) ESCs, BLHeli_32 DShot 1200 support, two 5V BECs, plus a voltmeter module that lets your FC know your battery's voltage and amperage in real-time! The F7 Flight Controller offers OSD, voltage monitoring, two BECs, and an interface for the DJI image

Hobbywing XRotor F722 3-6S 30x30 Stack/Combo (F7 FC / 32Bit 65A 4in1 ESC) (20x20 Mounting Option)

Hobbywing XRotor F722 3-6S 30x30 Stack/Combo (F7 FC / 32Bit 65A 4in1 E

The XRotor Micro Combo from Hobbywing continues to impress with its latest iteration. The Micro Combo features a 60A 4-in-1 ESC along with an updated F7 Flight Controller. This new FC is similar to other versions with its OSD, and voltage monitoring, but the F7 now comes with an all-new 5V &amp 12V dual BEC Circuit and a special interface for the DJI image transmission system.
he XRotor Micro Combo from Hobbywing continues to impress with its latest iteration. The Micro Combo features a 60A 4-in-1 ESC along with an updated F7 Flight Controller. This new FC is similar to other versions with its OSD, and voltage monitoring, but the F7 now comes with an all-new 5V &amp 12V dual BEC Circuit and a special interface for the DJI image transmission system.
Make your electronics stack work for you, not the other way around!
 
VIDEO: Xrotor F7 Convertible Flight Controller

Features
F7 FC

Equipped with STM32F722 MCU which has powerful computing ability and fast running speed, and high sensitivity ICM20602 six-axis motion sensor.
Supports BetaFlight, Cleanflight, Butterflight, Inva, and other mainstream FPV firmware.
DJI image transmission system port equipped with corresponding flat cable
Supports bidirectional DShot digital throttle communication.
Unique installation design and shock absorption structure.
On-board large capacity Flash memory chip.
On-board 5V &amp 12V dual BEC circuit.
On-board Pit Switch module.

60A 4-in-1 BLHeli_32 ESC

All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling.
The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us), and Multishot (5-25us).
Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power-up.
High-performance 32-bit microprocessor with a running frequency of up to 48MHz for an excellent performance.
Onboard 5V BEC, powering different accessories such as FC, VTX, Camera and LED lights and etc.
BLHeli_32 firmware is the third generation BLHeli.


Specifications
F7 FC

Compatible with (Modes): PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, DShot1200, Proshot1000 and etc
Compatible with (Transmitters): PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL
Mounting Holes: Convertible 20x20mm / 30.5x30.5mm
Programming via: Betaflight/Cleanflight-configurator
Firmware: HOBBYWING_XROTORF7CONV
Voltage Monitoring: Supported
Current Monitoring: Supported 
FC Programming: Supported
External Buzzer: Supported
BEC: 5V@1.5: 10V@1.5A
LED Control: Supported
USB Port: MicroUSB
Size: 32x32mm
OSD: Built-in
Weight: 3.3g

60A 4-in-1 ESC

Connectors: (In/Out) XT60 (w/ Wires Soldered on) /no
Input wires: 12AWG-130mm* (Red/Black)
Output Wire: No wires but solder tabs
Weight / Size: 15.0g / 52x42x6.6mm
ESC Programming: BLHeliSuite32
Throttle Calibration: Supported
Mounting holes: 30.5x30.5mm
LiPo Power input: 3S-6S
BEC Output: 5V@ 0.6A
Burst Current: 80Ax4
Cont.Current: 60Ax4

Manual

Hobbywing XRotor 60A 4-in-1 BLHeli_32 ESC
Hobbywing XRotor F7 FC

Includes

1x Hobbywing XRotor Micro Combo Stack - F7 FC + 60A 4-in-1 BLHeli_32 ESC
1x Soft Mounting Grommets Set
1x Signal Cable


Hobbywing XRotor Nano F4 Flight Controller w/ OSD | Bringing all the features from their larger FC, the Nano is a high power F4 Processor which is compatible with all common ESC protocols, as well as incredibly fast loop times! Compatible with DShot 1200

Hobbywing XRotor Micro Combo Stack - F7 FC + 60A 4-in-1 BLHeli_32 ESC

Hobbywing XRotor Nano F4 Flight Controller w/ OSD | Hobbywing

Hobbywing has heard your requests, and answered with this new amazing stack. Featuring a new F7 FC with their signature 60A ESC this stack is truly something to behold.
Check out all our 30x30 stacks &amp combos, and our Hobbywing selection!
Specifications
Hobbywing XRotor F7 FC

MCU: STM32F722
Gyro: ICM20602

Barometer: No
OSD: Yes
Blackbox: Onboard
UARTS: 4 Sets
ESC Software: DShot300/600/12000
ESC Telemetry: Yes
Led Controller: Yes
Input Voltage: 3-6s Lipo (12.6-25.2V)

BEC: 5V 2A / 10V 2A
Mounting: 20x20mm M3 / 30x30mm M3
Target: 

Hobbywing XRotor 60A 32Bit ESC

LiPo Power input: 3S-6S
Cont.Current: 60Ax4
Burst Current: 80Ax4
BEC Output: 5V@ 1.5A 
Input wires: 12AWG-130mm* (Red/Black)
Output Wire: No wires but solder tabs
Connectors: (In/Out) XT60 (w/ Wires Soldered on) /no
Weight / Size: 15.0g / 32.7x18.4x6.2mm
Mounting holes: 30.5x30.5mm
Throttle Calibration: Supported
ESC Programming: BLHeliSuite32

Includes

1x Hobbywing XRotor F7 FC
1x Hobbywing XRotor 60A 32Bit ESC
1x Hardware Set
1x AMASS XT60 Connector
1x Cable Set


Hobbywing has heard your requests, and answered with this new amazing stack. Featuring a new F7 FC with their signature 60A ESC this stack is truly something to behold. Check out all our 30x30 stacks &amp; combos, and our Hobbywing selection! Specifications Hobbywing XRotor F7 FC MCU: STM32F722 Gyro: ICM20602 Barometer

Hobbywing XRotor F722 3-6S 30x30 Stack/Combo (F7 FC / 32Bit 60A 4in1 ESC)

Hobbywing XRotor F722 3-6S 30x30 Stack/Combo (F7 FC / 32Bit 60A 4in1 E

The XRotor Micro Combo from Hobbywing continues to impress with its latest iteration. The Micro Combo features a 60A 4-in-1 ESC along with an updated F7 Flight Controller. This new FC is similar to other versions with its OSD, and voltage monitoring, but the F7 now comes with an all-new 5V & 12V dual BEC Circuit and a special interface for the DJI image transmission system.

The XRotor Micro Combo from Hobbywing continues to impress with its latest iteration. The Micro Combo features a 60A 4-in-1 ESC along with an updated F7 Flight Controller. This new FC is similar to other versions with its OSD, and voltage monitoring,












The Hobbywing XRotor F722 Stack/Combo packs in the latest tech: 65A (x4) ESCs, BLHeli_32 DShot 1200 support, two 5V BECs, plus a voltmeter module that lets your FC know your battery&#39s voltage and amperage in real-time! The F7 Flight Controller offers OSD, voltage monitoring, two BECs, and an interface for the DJI image transmission system. Build the perfect multirotor with this feature-packed, powerful combo! 











Check out all our 30x30 stacks &ampamp combos, and our Hobbywing selection!

Features


Manual for the FC

Manual for the ESC


XRotor 65A 4in1 ESC


High performance 32-bit microprocessor with the running frequency of up to 120MHz for excellent performance.


Third generation BLHeli_32 code can support up to 128KHz PWM output frequency, which can be compatible with more motors.


All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling.


Code supports features to prevent sync loss. There are tunable parameters that can make the code run well even in the most demanding situations, although default settings will work excellently in normal operating environments.


The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multishot (5-25us).


Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power up.


Also supports a beacon functionality, where the ESC will start beeping after a given time of zero throttle. This can be very useful for finding lost aircraft.


F7 Flight Controller Features


STM32 F722 MCU allows the FC to run the PID looptime and gyro with higher frequency.


Onboard OSD microchip which supports the DMA mode allows users to adjust its parameters via the Betaflight software. (Note: the OSD is controlled by the F4 MCU.)


The FC supports Betaflight firmware and allows parameter adjustment via Betaflight software is more applicable to FPV racing.


Onboard Flash chip can record and save flight/black box data allowing users to adjust the setup of their aircraft easily.


Compatible with various receivers like SBUS, SUMH, SUMD, SPEKTRUM1024/2048, XBUS and etc.


LED strip signal output port allows users to adjust the color and flash mode of the LED strip via the FC.


Volt/Amp monitoring port allows users to check the battery voltage (BAT port) and current (CRT port, extra current meter is needed).


Buzzer output port allows users to connect external buzzer(s) to the FC for warning or informing the flight status of the aircraft.


Micro USB port allows users to connect the FC to a PC to flash firmware and adjust parameters.

Board load 5V and 10V BEC, both can output 2A. It can supply power for receiver, VTX, LED lamp and others devices.


 Specifications

XRotor F7 FC

Compatible with (Multirotors) Quadcopters

Firmware HOBBYWING_XROTORF7CONV

FC Programming Supported

Programming via Betaflight/ Cleanflight-configurator

Compatible with (Modes) PWM, Oneshot125, Oneshot42, Multishot, Dshot150,
Dshot300, Dshot600, PROSHOT1000

Compatible with (Transmitters) PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL
OSD Built-in

Voltage Monitoring Supported

Current Monitoring Supported

External Buzzer Supported

LED Control Supported

BEC 5V @ 1.5A  10V @ 1.5A

Size 32x32mm

Weight 3.3g

XRotor 65A BLHeli_32 ESC

LiPo Power input: 3-6S

Cont.Current: 65Ax4

Burst Current: 80Ax4

BEC Output: 5V@ 0.5A 

Input wires: 12AWG-130mm* (Red/Black)

Output Wire: No wires but solder tabs

Connectors: (In/Out) XT60 (w/ Wires Soldered on) /no

Weight / Size: 15.0g / 32.7x18.4x6.2mm

Mounting holes: 30.5x30.5mm

Throttle Calibration: Supported

ESC Programming: BLHeliSuite32

Includes

1x Hobbywing XRotor F722 3-6S 30x30 Stack/Combo (F7 FC / 32Bit 65A 4in1 ESC)
1x Hardware Set
1x AMASS XT60 Connector
1x Cable Set


Hobbywing XRotor F722 3-6S 30x30 Stack/Combo (F7 FC / 32Bit 65A 4in1 ESC) (20x20 Mounting Option) from WREKD Co.

Hobbywing has heard your requests, and answered with this new amazing stack. Featuring a new F7 FC with their signature 60A ESC this stack is truly something to behold.
Check out all our 30x30 stacks &ampamp combos, and our Hobbywing selection!
Specifications
Hobbywing XRotor F7 FC

MCU: STM32F722
Gyro: ICM20602

Barometer: No
OSD: Yes
Blackbox: Onboard
UARTS: 4 Sets
ESC Software: DShot300/600/12000
ESC Telemetry: Yes
Led Controller: Yes
Input Voltage: 3-6s Lipo (12.6-25.2V)

BEC: 5V 2A / 10V 2A
Mounting: 20x20mm M3 / 30x30mm M3
Target: 

Hobbywing XRotor 60A 32Bit ESC

LiPo Power input: 3S-6S
Cont.Current: 60Ax4
Burst Current: 80Ax4
BEC Output: 5V@ 1.5A 
Input wires: 12AWG-130mm* (Red/Black)
Output Wire: No wires but solder tabs
Connectors: (In/Out) XT60 (w/ Wires Soldered on) /no
Weight / Size: 15.0g / 32.7x18.4x6.2mm
Mounting holes: 30.5x30.5mm
Throttle Calibration: Supported
ESC Programming: BLHeliSuite32

Includes

1x Hobbywing XRotor F7 FC
1x Hobbywing XRotor 60A 32Bit ESC
1x Hardware Set
1x AMASS XT60 Connector
1x Cable Set


Hobbywing XRotor F722 3-6S 30x30 Stack/Combo (F7 FC / 32Bit 60A 4in1 ESC) from WREKD Co.

HobbyWing

HobbyWing FPV Stack Micro 60A ESC + FC F7 Convertible

HobbyWing FPV Stack Micro 60A ESC + FC F7 Convertible - RMRC

Hobbywing XRotor F722 3-6S 20x20/30x30 Flight Controller Stack - F7 FC, 40A 32Bit 4in1 ESC


Hobbywing has heard your requests, and answered with this new amazing stack. Featuring a new F7 FC with their signature 40A ESC this stack is truly something to behold.
Specifications
XRotor F7 FC


MCU: STM32F722
Gyro: ICM20602

Barometer: No
OSD: Yes
Blackbox: Onboard
UARTS: 4 Sets
ESC Software: DShot300/600/12000
ESC Telemetry: Yes
Led Controller: Yes
Input Voltage: 3-6s Lipo (12.6-25.2V)

BEC: 5V 2A / 10V 2A
Mounting Pattern: 20x20mm M3 / 30x30mm M3

XRotor 40A BLHeli_32 ESC

Input Voltage: 3-6S
Max Continuous Current: 40A 
Max Burst Current: 60A 
BEC Output: NO
Firmware: Hobbywing_XRotor_BLHeli-32 Version
Throttle Calibration: Supported
ESC Programming: Stick Programming, BLHeliSuite32
DEO: Supported
OneShot Mode: Supported
Timing: Supported
Motor Rotation: Supported
Mounting Pattern: 20x20mm

Weight: 12g

Includes

1x Hobbywing XRotor F722 3-6S 20x20 Stack/Combo (F7 FC / 32Bit 40A 4in1 ESC)
1x Hardware Set
1x AMASS XT60 Connector
1x Cable Set


Hobbywing has heard your requests, and answered with this new amazing stack. Featuring a new F7 FC with their signature 40A ESC; this stack is truly something to behold. Specifications XRotor F7 FC MCU: STM32F722 Gyro: ICM20602 Barometer: No OSD: Yes Blackbox: Onboard UARTS: 4 Sets ESC Software: DShot300/600/12000 ESC 

Hobbywing XRotor F722 3-6S 20x20 Stack/Combo (F7 FC / 32Bit 40A 4in1 ESC) from WREKD Co.

Hobbywing XRotor F722 3-6S 20x20 Stack/Combo (F7 FC / 32Bit 40A 4in1 ESC)

Hobbywing has heard your requests, and answered with this new amazing stack. Featuring a new F7 FC with their signature 40A ESC this stack is truly something to behold.
Check out all our 20x20 stacks, and our Hobbywing selection!
Specifications
XRotor F7 FC

MCU: STM32F722
Gyro: ICM20602

Barometer: No
OSD: Yes
Blackbox: Onboard
UARTS: 4 Sets
ESC Software: DShot300/600/12000
ESC Telemetry: Yes
Led Controller: Yes
Input Voltage: 3-6s Lipo (12.6-25.2V)

BEC: 5V 2A / 10V 2A
Mounting Pattern: 20x20mm M3 / 30x30mm M3

XRotor 40A BLHeli_32 ESC

Input Voltage: 3-6S
Max Continuous Current: 40A 
Max Burst Current: 60A 
BEC Output: NO
Firmware: Hobbywing_XRotor_BLHeli-32 Version
Throttle Calibration: Supported
ESC Programming: Stick Programming, BLHeliSuite32
DEO: Supported
OneShot Mode: Supported
Timing: Supported
Motor Rotation: Supported
Mounting Pattern: 20x20mm

Weight: 12g

Includes

1x Hobbywing XRotor F722 3-6S 20x20 Stack/Combo (F7 FC / 32Bit 40A 4in1 ESC)
1x Hardware Set
1x AMASS XT60 Connector
1x Cable Set


Hobbywing has heard your requests, and answered with this new amazing stack. Featuring a new F7 FC with their signature 40A ESC; this stack is truly something to behold. Check out all our 20x20 stacks, and our Hobbywing selection! Specifications XRotor F7 FC MCU: STM32F722 Gyro: ICM20602 Barometer: No OSD: Yes Blackbox

Hobbywing XRotor F722 3-6S 20x20 Stack/Combo (F7 FC / 32Bit 40A 4in1 E

The XRotor Micro Combo from Hobbywing continues to impress with its latest iteration. The Micro Combo features a 40A 4-in-1 ESC along with an updated F7 Flight Controller.