FPV Quad Parts

Peripherals and Replacement Parts

Equipment

Equipment Peripherals

Build Page Parts

Build Parts Equipment

Pre-Built Quads and Kits 

Build Page Parts Overflow

Build Parts Equipment Overflow

Compatibility Categories

Continuous Amp Rating

NewBeeDrone

NewBeeDrone x Team BlackSheep BeeBrain BLV4 AIO Flight Controller - 12A ESC, Crossfire Rx

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built in Crossfire Rx
Warning:

We would like to remind you that our flight controller product is designed to work with our own product line. While we have taken every possible measure to ensure the quality and compatibility of our product line, using third party components may result in incompatibility or improper functioning of the product. such as Camere with different voltage signal will mass up the OSD function, frame from other company that is not fitting well with our FC, Motor plug are not compatible with the JST1.0 on the FC. etc. 
We strongly recommend that you verify the compatibility and functioning before any soldering or modification. 

Please be aware, drone flight controller will break due to crash, any physical damage or crash will have posibility to destory the hardware. This is also not cover by our warranty.  If you find that the product is Dead On Arrival (DOA), we will replace it for you free of charge.
However, we cannot take responsibility for any issues that may arise due to modifications made to the product or the use 3rd party components. In such cases, we will not be able to provide support or warranty coverage. 

Thank you for your understanding and for choosing our product. If you have any questions or concerns, please don&#39t hesitate to contact our customer support team.
This product is designed mainly to be a replacement part for the NewBeeDrone x Team BlackSheep AcroBee65 BLV4 Crossfire. 

BeeBrain BLV4 CRSF Spec:
MCU: STM32F411GYRO：BMI270VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw)  with BeeTX 5.8Ghz AntennaESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHzESC Connector: JST-1.0 3PinOSD: NBD7456 Graphical OSD compatible with Betaflight OSDReceiver: Crossfire Nano receiver with MINIMORTAL T ANTENNAFlight Controller Weight: 6.5g(Include antennas and battery connector)Flight Controller Size: Outer dimensions: 29x29x7.6mmFlight Controller Holes: 25.5x25.5mmBattery input: 1SUart2: Crossfire Nano receiver 
Power Connector: NBD-PH2.0 connector
Includes


1 x BeeBrain BLV4 CRSF Flight Controller
4 x Grommet
4 x Screw

1 x MINIMORTAL T Antenna
1 x VTX Antenna




Firmware: 1. BeeBrain BLV4 CRSF Betaflight 4.4  firmware 
All New firmware can be found on our Github Page

All firmware can be found on our Github PageWire Diagram:
 

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built in Crossfire Rx Warning: We would like to remind you that our flight controller product is designed to work with our own product line. While we have taken every possible measure to ensure the quality and compatibility of our product line, using third party components ma

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built-in Crossfire Rx AIO Flight Controller from WREKD Co.

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built-in Crossfire Rx AIO Flight Controller

NEWBEEDRONE

The NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller provides optimal performance for pilots who want a compact build. This single board is equipped with a flight controller, 12A 32Bit 4in1 ESC, 5.8GHz VTX, and a TBS Crossfire receiver, all on a 29x29mm platform. Enjoy advanced features and excellent performance for your compact setup! 
The new "Smart Max" technology uses the MCU to read the board temperature on the back of the VTEC chip and uses PID control to control the output power of the VTX amplifier. When the board temperature rises, the VTX power will be automatically reduced. When the temperature is low, the maximum output power can be up to 400mW. If
Check out all our Whoop/AIO Flight Controllers and the rest of our NewBeeDrone products.
Features

Built-In TBS Crossfire Nano Receiver
SmartMAX (SmartMax up to 400mw) 
25x25 Mounting Pattern
5w/25w Switchable VTX
F411 Flight Controller
12A BLHeli_S ESC
1-2S Voltage
BMI270 Gyro

Specifications

MCU: STM32F411
GYRO：BMI270
VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw) with BeeTX 5.8Ghz Antenna
ESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHz
ESC Connector: JST-1.0 3Pin
OSD: NBD7456 Graphical OSD compatible with Betaflight OSD
Receiver: Crossfire Nano receiver with MINIMORTAL T ANTENNA
Flight Controller Weight: 6.5g(Include antennas and battery connector)
Flight Controller Size: Outer dimensions: 29x29x7.6mm
Flight Controller Holes: 25.5x25.5mm
Battery input: 1-2S (For 2S you will need to set throttle cap at less 50%)
Uart2: Crossfire Nano receiver 
Power Connector: NBD-PH2.0 connector

Additional Information

UART2 TX and RX for onboard Crossfire (CRSF)

UART1 TX and RX free

VTX Adjustable power 5mW-25mW-SmartMAX. SmartMAX will automatically adjust the VTX power according to the board temperature. When the board temperature rises, the VTX power will be automatically reduced. When the temperature is low, the maximum output power can be up to 400mW.

Firmware 

Download: BeeBrain BLV4 CRSF Betaflight 4.4 firmware


Includes

1x NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller w/ 12A 8Bit 4in1 ESC &amp 400mW VTX - CRSF
4x Grommet
4x Screw

1x Receiver T-Antennas 


1x Receiver Mono Pole Antenna


1x VTX Antenna


Wiring Diagram 


The NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller provides optimal performance for pilots who want a compact build. This single board is equipped with a flight controller, 12A 32Bit 4in1 ESC, 5.8GHz VTX, and a TBS Crossfire receiver, all on a 29x29mm platform. Enjoy advanced features and exc

NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller w/ 12A 8Bit 4in1 ESC & 400mW VTX - CRSF

NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Control

The BeeBrain BLV4 AIO Flight Controller integrates an F411 flight controller, a 12AMP 4-In-1 BLHeli_S ESC, a 5.8GHz VTX, and a TBS Crossfire receiver onto a compact 29x29mm platform.

NewBeeDrone BeeBrain BLV4 AIO - F411 FC + 12A 1-2S BLHeli_S ESC + Built-In TBS Crossfire

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built in Crossfire Rx
Warning:

We would like to remind you that our flight controller product is designed to work with our own product line. While we have taken every possible measure to ensure the quality and compatibility of our product line, using third party components may result in incompatibility or improper functioning of the product. such as Camere with different voltage signal will mass up the OSD function, frame from other company that is not fitting well with our FC, Motor plug are not compatible with the JST1.0 on the FC. etc. 
We strongly recommend that you verify the compatibility and functioning before any soldering or modification. 

Please be aware, drone flight controller will break due to crash, any physical damage or crash will have posibility to destory the hardware. This is also not cover by our warranty.  If you find that the product is Dead On Arrival (DOA), we will replace it for you free of charge.
However, we cannot take responsibility for any issues that may arise due to modifications made to the product or the use 3rd party components. In such cases, we will not be able to provide support or warranty coverage. 

Thank you for your understanding and for choosing our product. If you have any questions or concerns, please don't hesitate to contact our customer support team.
This product is designed mainly to be a replacement part for the NewBeeDrone x Team BlackSheep AcroBee65 BLV4 Crossfire. 

BeeBrain BLV4 CRSF Spec:
MCU: STM32F411GYRO：BMI270VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw)  with BeeTX 5.8Ghz AntennaESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHzESC Connector: JST-1.0 3PinOSD: NBD7456 Graphical OSD compatible with Betaflight OSDReceiver: Crossfire Nano receiver with MINIMORTAL T ANTENNAFlight Controller Weight: 6.5g(Include antennas and battery connector)Flight Controller Size: Outer dimensions: 29x29x7.6mmFlight Controller Holes: 25.5x25.5mmBattery input: 1SUart2: Crossfire Nano receiver 
Power Connector: NBD-PH2.0 connector
Includes


1 x BeeBrain BLV4 CRSF Flight Controller
4 x Grommet
4 x Screw

1 x MINIMORTAL T Antenna
1 x VTX Antenna




Firmware: 1. BeeBrain BLV4 CRSF Betaflight 4.4  firmware 
All New firmware can be found on our Github Page

All firmware can be found on our Github PageWire Diagram:
 

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built-in Crossfire Rx AIO 

The NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller provides optimal performance for pilots who want a compact build. This single board is equipped with a flight controller, 12A 32Bit 4in1 ESC, 5.8GHz VTX, and a TBS Crossfire receiver, all on a 29x29mm platform. Enjoy advanced features and excellent performance for your compact setup! 
The new &quotSmart Max&quot technology uses the MCU to read the board temperature on the back of the VTEC chip and uses PID control to control the output power of the VTX amplifier. When the board temperature rises, the VTX power will be automatically reduced. When the temperature is low, the maximum output power can be up to 400mW. If
Check out all our Whoop/AIO Flight Controllers and the rest of our NewBeeDrone products.
Features

Built-In TBS Crossfire Nano Receiver
SmartMAX (SmartMax up to 400mw) 
25x25 Mounting Pattern
5w/25w Switchable VTX
F411 Flight Controller
12A BLHeli_S ESC
1-2S Voltage
BMI270 Gyro

Specifications

MCU: STM32F411
GYRO：BMI270
VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw) with BeeTX 5.8Ghz Antenna
ESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHz
ESC Connector: JST-1.0 3Pin
OSD: NBD7456 Graphical OSD compatible with Betaflight OSD
Receiver: Crossfire Nano receiver with MINIMORTAL T ANTENNA
Flight Controller Weight: 6.5g(Include antennas and battery connector)
Flight Controller Size: Outer dimensions: 29x29x7.6mm
Flight Controller Holes: 25.5x25.5mm
Battery input: 1-2S (For 2S you will need to set throttle cap at less 50%)
Uart2: Crossfire Nano receiver 
Power Connector: NBD-PH2.0 connector

Additional Information

UART2 TX and RX for onboard Crossfire (CRSF)

UART1 TX and RX free

VTX Adjustable power 5mW-25mW-SmartMAX. SmartMAX will automatically adjust the VTX power according to the board temperature. When the board temperature rises, the VTX power will be automatically reduced. When the temperature is low, the maximum output power can be up to 400mW.

Firmware 

Download: BeeBrain BLV4 CRSF Betaflight 4.4 firmware


Includes

1x NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller w/ 12A 8Bit 4in1 ESC &ampamp 400mW VTX - CRSF
4x Grommet
4x Screw

1x Receiver T-Antennas 


1x Receiver Mono Pole Antenna


1x VTX Antenna


Wiring Diagram 


NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller w/ 12A 8Bit 4in1 ESC & 400mW VTX - CRSF from WREKD Co.

Processor (MCU)

The FC is the brain or the CPU of your quad. It has a processor and other components that allow it to listen to your inputs and tells the quad what to do. FCs are commonly sold together with other components integrated or stacked (like ESCs and video transmitters). For beginners, choose a FC with a F4 or F7 processor that has a compatible mount with your frame. 

Flight Controllers

FC Stack Mount

Built-in VTX

Built-in ESC

SpeedyBee

SpeedyBee F405 V4 Flight Controller Stack - 55A 3-6S 4in1 ESC

RUNCAM

Richer features, unbelievable price!












The SpeedyBee F405 V4 BLS 3-6S 30x30 Stack/Combo is a powerhouse of features at a remarkably competitive price. It boasts a wireless FC &amp ESC configuration, dual gyroscope power supply filtering, onboard 4-level battery indicators, 8 motor support, 4x LED strips soldering pads, 3A output 5V &amp 9V BECs, fixed SD card compatibility issue, wireless motor direction change, a DJI Air Unit plug-and-play, and a built-in barometer. Get it now and enjoy an unparalleled performance!
The powerful 55A (70A burst) 4-in-1 ESC, built with aluminum alloy heat sink + TVS protective diode + Japan made TDK SMT capacitors + external 1000uF low ESR capacitor, everything is for a durable build and smooth flight.
All of that for only $69.99! Top-shelf spec at a crazy low price, what are you waiting for?
Interested in the SpeedyBee BLS 8Bit 55A 3-6S 30x30 4in1 ESC?
Interested in the SpeedyBee F405 V4 3-6S 30x30 Flight Controller?
Check out all our 30x30 stacks &amp combos, and all our Speedy Bee products!












Features

User manual
Wireless FC &amp ESC full configuration
ESC upgraded to 55A with heat sink 
Dual gyroscope power supply filtering 
Onboard 4-level battery indicators
Supports up to 8 Motors 
4x LED strips soldering pads
5V &amp 9V BECs upgraded to 3A output
Fixed SD card compatibility issue
Change motor direction wirelessly 
1000uF huge filtering capacitor 
DJI Air Unit plug-and-play
Built-in barometer









































Specifications
SpeedyBee F405 V4 30x30 Flight Controller

MCU: STM32F405

IMU(Gyro): ICM42688P

USB Port Type: Type-C

Barometer: Built-in

OSD Chip: AT7456E chip

BLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)

WIFI: Not supported

DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.

6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Blackbox MicroSD Card Slot: Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. 

Current Sensor Input: Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0.

Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)

5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.

9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.

3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output: Supported. Designed for a receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.

UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

ESC Telemetry: UART R5(UART5)

I2C: Supported. SDA &amp SCL pads on front side. Used for magnetometer, sonar, etc.

Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.

Buzzer: BZ+ and BZ- pad used for 5V Buzzer

BOOT Button: Supported.[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input: Supported. Named as RS on the front side.

Smart Port / F.Port: Not supported

Supported Flight Controller Firmware: BetaFlight(Default), INAV

Firmware Target Name: SPEEDYBEEF405V4

Mounting: 30.5 x 30.5mm( 4mm hole diameter)

Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm

Weight: 10.5g

SpeedyBee BLS 55A 30x30 4-in-1 ESC

Firmware: BLHeli_S J-H-40

Wireless Configuration: Full Configuration Supported in the SpeedyBee app

PC Configurator Download Link: https://esc-configurator.com/
Continuous Current: 55A x 4
Burst Current: 70(10 seconds)
TVS Protective diode: Yes
External Capacitor: 1000uF Low ESR Capacitor(In the package)
ESC Protocol: DSHOT300/600
Power Input: 3-6S LiPo
Power Output: VBAT
Current Sensor: Support (Scale=400 Offset=0)
ESC Telemetry: Not supported
Mounting: 30.5 x 30.5mm( 4mm hole diameter)
Dimension: 45.6(L) x 44(W) x 8mm(H)
Weight: 23.5g

Includes

1x SpeedyBee F405 V4  BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC)


 Wiring Diagram




Richer features, unbelievable price! The SpeedyBee F405 V4 BLS 3-6S 30x30 Stack/Combo is a powerhouse of features at a remarkably competitive price. It boasts a wireless FC &amp; ESC configuration, dual gyroscope power supply filtering, onboard 4-level battery indicators, 8 motor support, 4x LED strips soldering pads, 

SpeedyBee F405 V4  BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC)

SpeedyBee F405 V4 BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 

Richer features, unbelievable price!












The SpeedyBee F405 V4 BLS 3-6S 30x30 Stack/Combo is a powerhouse of features at a remarkably competitive price. It boasts a wireless FC &ampamp ESC configuration, dual gyroscope power supply filtering, onboard 4-level battery indicators, 8 motor support, 4x LED strips soldering pads, 3A output 5V &ampamp 9V BECs, fixed SD card compatibility issue, wireless motor direction change, a DJI Air Unit plug-and-play, and a built-in barometer. Get it now and enjoy an unparalleled performance!
The powerful 55A (70A burst) 4-in-1 ESC, built with aluminum alloy heat sink + TVS protective diode + Japan made TDK SMT capacitors + external 1000uF low ESR capacitor, everything is for a durable build and smooth flight.
All of that for only $69.99! Top-shelf spec at a crazy low price, what are you waiting for?
Interested in the SpeedyBee BLS 8Bit 55A 3-6S 30x30 4in1 ESC?
Interested in the SpeedyBee F405 V4 3-6S 30x30 Flight Controller?
Check out all our 30x30 stacks &ampamp combos, and all our Speedy Bee products!












Features

User manual
Wireless FC &ampamp ESC full configuration
ESC upgraded to 55A with heat sink 
Dual gyroscope power supply filtering 
Onboard 4-level battery indicators
Supports up to 8 Motors 
4x LED strips soldering pads
5V &ampamp 9V BECs upgraded to 3A output
Fixed SD card compatibility issue
Change motor direction wirelessly 
1000uF huge filtering capacitor 
DJI Air Unit plug-and-play
Built-in barometer









































Specifications
SpeedyBee F405 V4 30x30 Flight Controller

MCU: STM32F405

IMU(Gyro): ICM42688P

USB Port Type: Type-C

Barometer: Built-in

OSD Chip: AT7456E chip

BLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)

WIFI: Not supported

DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.

6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Blackbox MicroSD Card Slot: Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. 

Current Sensor Input: Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0.

Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)

5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.

9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.

3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output: Supported. Designed for a receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.

UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

ESC Telemetry: UART R5(UART5)

I2C: Supported. SDA &ampamp SCL pads on front side. Used for magnetometer, sonar, etc.

Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.

Buzzer: BZ+ and BZ- pad used for 5V Buzzer

BOOT Button: Supported.[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input: Supported. Named as RS on the front side.

Smart Port / F.Port: Not supported

Supported Flight Controller Firmware: BetaFlight(Default), INAV

Firmware Target Name: SPEEDYBEEF405V4

Mounting: 30.5 x 30.5mm( 4mm hole diameter)

Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm

Weight: 10.5g

SpeedyBee BLS 55A 30x30 4-in-1 ESC

Firmware: BLHeli_S J-H-40

Wireless Configuration: Full Configuration Supported in the SpeedyBee app

PC Configurator Download Link: https://esc-configurator.com/
Continu..

SpeedyBee F405 V4  BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC) from WREKD Co.

With only $69.99, you will get an STM32F405 FC (better than F411), onboard 4-level battery life indicator, 4GB Blackbox SD card slot for your flight logs, 4 groups of LED strip pads, complete with a DJI plug for your digital quad, and built-in Bluetooth for wireless configuration on the SpeedyBee app. Don't forget abou

SpeedyBee F405 V4 Stack w/ 55A 3-6S BLS 4in1 ESC - 30x30mm

Elevate your drone's performance with the SpeedyBee F405 V4 Stack, featuring STM32F405 MCU and ICM42688P gyro for precise control.&nbsp

Elevate your drone's performance with the SpeedyBee F405 V4 Stack, featuring STM32F405 MCU and ICM42688P gyro for precise control. 

SpeedyBee F405 V4 Stack - F4 V4 FC + 55A BLHeli_S ESC - 30x30

SpeedyBee F405 V4 Flight Controller

Elevate your drone's performance with the SpeedyBee F405 V4 Flight Controller, featuring STM32F405 MCU and ICM42688P gyro for precise control.&nbsp

Elevate your drone's performance with the SpeedyBee F405 V4 Flight Controller, featuring STM32F405 MCU and ICM42688P gyro for precise control. 

SpeedyBee F405 V4 Flight Controller - 30x30

Introducing the SpeedyBee F405 V4 flight controller with dual gyroscope power supply filtering, 4-level battery indicators, support for up to 8 motors, 4x LED strip soldering pads, 3A 5V &ampamp 9V BECs, and fixed SD card compatibility issue. Change motor direction wirelessly and quickly get set up with the DJI Air Unit plug-and-play set up. Plus, onboard barometer is included.












Interested in the SpeedyBee F405 V4  BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC)?
Interested in the SpeedyBee BLS 8Bit 55A 3-6S 30x30 4in1 ESC?
Check out all our 30x30 stacks &ampamp combos, and all our Speedy Bee products!
Features














User manual
Wireless FC &ampamp ESC full configuration
Dual gyroscope power supply filtering 

Onboard 4-level battery indicators
Supports up to 8 Motors 
4x LED strips soldering pads
5V &ampamp 9V BECs upgraded to 3A output
Fixed SD card compatibility issue
Change motor direction wirelessly 
DJI Air Unit plug-and-play

Built-in barometer








































Specifications
SpeedyBee F405 V4 30x30 Flight Controller

MCU: STM32F405

IMU(Gyro): ICM42688P

USB Port Type: Type-C

Barometer: Built-in

OSD Chip: AT7456E chip

BLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)

WIFI: Not supported

DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.

6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Blackbox MicroSD Card Slot: Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. 

Current Sensor Input: Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0.

Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)

5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.

9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.

3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output: Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.

UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

ESC Telemetry: UART R5(UART5)

I2C: Supported. SDA &ampamp SCL pads on front side. Used for magnetometer, sonar, etc.

Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.

Buzzer: BZ+ and BZ- pad used for 5V Buzzer

BOOT Button: Supported.[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input: Supported. Named as RS on the front side.

Smart Port / F.Port: Not supported

Supported Flight Controller Firmware: BetaFlight(Default), INAV

Firmware Target Name: SPEEDYBEEF405V4

Mounting: 30.5 x 30.5mm( 4mm hole diameter)

Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm

Weight: 10.5g


Includes

1x SpeedyBee F405 V4 3-6S 30x30 Flight Controller


 Wiring Diagram



Introducing the SpeedyBee F405 V4 flight controller with dual gyroscope power supply filtering, 4-level battery indicators, support for up to 8 motors, 4x LED strip soldering pads, 3A 5V &amp; 9V BECs, and fixed SD card compatibility issue. Change motor direction wirelessly and quickly get set up with the DJI Air Unit 

SpeedyBee F405 V4 3-6S 30x30 Flight Controller from WREKD Co.

SpeedyBee F405 V4 3-6S 30x30 Flight Controller

SpeedyBee F405 V4 FC uses the STM32F405 chip (better than F411), onboard 4-level battery life indicator, 4GB Blackbox SD card slot for your flight logs, 4 groups of LED strip pads, complete with a DJI plug for your digital quad, and built-in Bluetooth for wireless configuration on the SpeedyBee app. * The DJI Air Unit 

SpeedyBee F405 V4 Flight Controller - 30x30mm

Speedybee

Introducing the SpeedyBee F405 V4 BLS 55A 30x30 FC&ampESC Stack – a high-performance flight controller and ESC combination that redefines value for money. Packed with top-shelf features, this stack offers exceptional performance at an unbeatable price of $69.99.Key Features:Powerful STM32F405 FC: Outclassing the F411, the STM32F405 FC ensures precise and responsive flight control.Onboard Battery Life Indicator: Stay informed with the 4-level battery life indicator, eliminating the need for additional tools.4GB Blackbox SD Card Slot: Capture and review your flight logs effortlessly with the onboard 4GB Blackbox SD card slot.DJI Plug Compatibility: Seamlessly connect your digital quad with the DJI plug, compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1.Built-in Bluetooth: Configure your setup wirelessly using the SpeedyBee app, enhancing user convenience.Robust 55A 4-in-1 ESC: The ESC features an aluminum alloy heat sink, TVS protective diode, Jap...

The best quality First Person View equipment. Free or discounted shipping on all orders.Drone Racing, RC Airplanes, FPV Cameras, FPV Goggles, Video Transmitters, RC Quads, Drone Antennas, Lipo Batteries, and Ground Station Equipment.All available for amateurs, schools, hobbyists, government, and wholesale buyers.

SpeedyBee F405 V4 BLS 55A 30x30 FC&ESC Stack - RMRC

SpeedyBee F405 V4 BLS 55A 30x30 FC&ampESC Stack

Introducing the SpeedyBee F405 V4 flight controller with dual gyroscope power supply filtering, 4-level battery indicators, support for up to 8 motors, 4x LED strip soldering pads, 3A 5V &amp 9V BECs, and fixed SD card compatibility issue. Change motor direction wirelessly and quickly get set up with the DJI Air Unit plug-and-play set up. Plus, onboard barometer is included.












Interested in the SpeedyBee F405 V4  BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC)?
Interested in the SpeedyBee BLS 8Bit 55A 3-6S 30x30 4in1 ESC?
Check out all our 30x30 stacks &amp combos, and all our Speedy Bee products!
Features














User manual
Wireless FC &amp ESC full configuration
Dual gyroscope power supply filtering 

Onboard 4-level battery indicators
Supports up to 8 Motors 
4x LED strips soldering pads
5V &amp 9V BECs upgraded to 3A output
Fixed SD card compatibility issue
Change motor direction wirelessly 
DJI Air Unit plug-and-play

Built-in barometer








































Specifications
SpeedyBee F405 V4 30x30 Flight Controller

MCU: STM32F405

IMU(Gyro): ICM42688P

USB Port Type: Type-C

Barometer: Built-in

OSD Chip: AT7456E chip

BLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)

WIFI: Not supported

DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.

6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Blackbox MicroSD Card Slot: Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. 

Current Sensor Input: Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0.

Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)

5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.

9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.

3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output: Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.

UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

ESC Telemetry: UART R5(UART5)

I2C: Supported. SDA &amp SCL pads on front side. Used for magnetometer, sonar, etc.

Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.

Buzzer: BZ+ and BZ- pad used for 5V Buzzer

BOOT Button: Supported.[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input: Supported. Named as RS on the front side.

Smart Port / F.Port: Not supported

Supported Flight Controller Firmware: BetaFlight(Default), INAV

Firmware Target Name: SPEEDYBEEF405V4

Mounting: 30.5 x 30.5mm( 4mm hole diameter)

Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm

Weight: 10.5g


Includes

1x SpeedyBee F405 V4 3-6S 30x30 Flight Controller


 Wiring Diagram



Matek

Matek F405-WMN Flight Controller 

Matek Systems

Matek's F405-WMN (Wing Mini) board is a great flight controller for those looking to save space and weight on their builds.&nbsp It puts pretty much all features from a full-size&nbspboard on something that measures just 31x26x16mm.&nbsp&nbsp

Matek's F405-WMN (Wing Mini) board is a great flight controller for those looking to save space and weight on their builds.  It puts pretty much all features from a full-size board on something that measures just 31x26x16mm.  

MATEKSYS F405-WMN Flight Controller 

Happymodel

Happymodel DiamondF4 1S AIO Whoop Flight Controller - F4 FC, 5A ESC, 25-200mW VTX

The Happymodel Diamond F4 AIO 5-IN-1 Flight Controller has a built-in VTX, ESC, OSD, and receiver - all on one triangle-shaped whoop board!

Happymodel Diamond F4 ELRS 5-in-1 AIO Flight Controller - SPI ELRS 2.4GHz

Happymodel DiamondF4 AIO 5-IN-1 Flight controller built-in VTX ESC OSD Receiver with Frsky Receiver For Moblite 6/7 Check out all our Flight Controllers! Specification: Flight controller: (Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FR MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI con

Happymodel DiamondF4 AIO 5-IN-1 Flight controller built-in VTX ESC OSD Receiver with Frsky Receiver For Moblite 6/7

Happymodel X12 5in1 AIO Flight Controller - F4 FC, 12A ESC, 400mW VTX, RX

HAPPYMODEL

The HappyModel X12 2S AIO Whoop Flight Controller (F4 FC / 12A 4in1 ESC / 25-400mW VTX) AIO board featuring an F4 Flight Controller, onboard 12A 4-in-1 ESC, 5.8GHz OpenVTX and built-in receiver of your choice! Happymodel continues to impress with yet another fantastic AIO for whoop applications!
Browse the rest of our Whoop AIO boards and all our Happymodel products! 
Specifications

Input Voltage: 1-2S
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: MPU6000 or ICM20689 or BMI270
Max Continuous Current: 12A
VTX Output Power: 25-400mW
Antenna Connector: U.FL
OSD: Yes
Betaflight Target: ELRS Version: CRAZYBEEF4SX1280, PNP Version: CRAZYBEEF4DX
ESC Firmware: Z_H_30_REV16_7
Mounting Pattern: 25x25mm
Weight: 5.1g

ELRS Version

Packet Rate: 50Hz/150Hz/250Hz/500Hz
ELRS Firmware Version: V2.0
RF Frequency: 2.4GHz
Antenna: SMD antenna
Telemetry output Power: &lt12dBm

Includes

1x HappyModel X12 2S AIO Whoop Flight Controller (F4 FC / 12A 4in1 ESC / 25-400mW VTX)
1x Connecting Wires Set
1x Hardware Set
1x Antenna



Increase your range with the impressive HappyModel X12 2S AIO Whoop Flight Controller. Optimize your flight today!

HappyModel X12 2S AIO Whoop Flight Controller (F4 FC / 12A 4in1 ESC / 25-400mW VTX) - Choose Version

HappyModel X12 2S AIO Whoop Flight Controller (F4 FC / 12A 4in1 ESC / 25-400mW VTX) - For Sale

The Happymodel X12&nbspis a&nbsp5-in-1&nbspAIO board featuring an F4 Flight Controller, onbard 12A 4-in-1 ESC, 5.8GHz OpenVTX, and three different receiver options:&nbspPNP, FrSky, or ELRS. This AIO is great for brushless whoops with its great RX an VTX range!

The Happymodel X12 is a 5-in-1 AIO board featuring an F4 Flight Controller, onbard 12A 4-in-1 ESC, 5.8GHz OpenVTX, and three different receiver options: PNP, FrSky, or ELRS. This AIO is great for brushless whoops with its great RX

Happymodel X12 AIO 5-in-1 Board - F4 FC + 12A ESC

The HappyModel X12 2S AIO Whoop Flight Controller (F4 FC / 12A 4in1 ESC / 25-400mW VTX) AIO board featuring an F4 Flight Controller, onboard 12A 4-in-1 ESC, 5.8GHz OpenVTX and built-in receiver of your choice! Happymodel continues to impress with yet another fantastic AIO for whoop applications!
Browse the rest of our Whoop AIO boards and all our Happymodel products! 
Specifications

Input Voltage: 1-2S
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: MPU6000 or ICM20689 or BMI270
Max Continuous Current: 12A
VTX Output Power: 25-400mW
Antenna Connector: U.FL
OSD: Yes
Betaflight Target: ELRS Version: CRAZYBEEF4SX1280, PNP Version: CRAZYBEEF4DX
ESC Firmware: Z_H_30_REV16_7
Mounting Pattern: 25x25mm
Weight: 5.1g

ELRS Version

Packet Rate: 50Hz/150Hz/250Hz/500Hz
ELRS Firmware Version: V2.0
RF Frequency: 2.4GHz
Antenna: SMD antenna
Telemetry output Power: &amplt12dBm

Includes

1x HappyModel X12 2S AIO Whoop Flight Controller (F4 FC / 12A 4in1 ESC / 25-400mW VTX)
1x Connecting Wires Set
1x Hardware Set
1x Antenna



The HappyModel X12 2S AIO Whoop Flight Controller (F4 FC / 12A 4in1 ESC / 25-400mW VTX) AIO board featuring an F4 Flight Controller, onboard 12A 4-in-1 ESC, 5.8GHz OpenVTX and built-in receiver of your choice! Happymodel continues to impress with yet another fantastic AIO for whoop applications! Browse the rest of our 

HappyModel X12 2S AIO Whoop Flight Controller (F4 FC / 12A 4in1 ESC / 25-400mW VTX) - Choose Version from WREKD Co.

Lumenier

Lumenier LUX F4 HD Ultimate 30x30 Flight Controller 

The Lumenier LUX F4 HD Ultimate Flight Controller is full of features including a plug for DJI HD system, 3rd generation IMU ICM42688-P, dual plug-and-play 4in1 ESC ports, 12x PWM outputs, barometer, OSD, 6x UARTs, 9-16V BEC, dual analog camera inputs, easy soldering layout and much more...LUX H7 is compatible with:BetaflightArduPilotiNav (comes pre-loaded by default from factory)

The Lumenier LUX F4 HD Ultimate Flight Controller is full of features including a plug for DJI HD system, 3rd generation IMU ICM42688-P, dual plug-and-play 4in1 ESC ports, 12x PWM outputs, barometer, OSD, 6x UARTs, 9-16V BEC, dual analog camera input

Lumenier LUX F4 HD Ultimate Flight Controller 

JHEMCU

JHEMCU NOXE F4 V2 Deluxe 20x20 Flight Controller For DJI

The&nbspJHEMCU NOXE F4 V2 Flight Controller&nbspis made with DJI Pilots in mind. This Deluxe FC packs a 16MB Blackbox, Barometer, 2 UARTs, and BEC into a mini-sized 20x20 board with 3-6S capabilities!

The JHEMCU NOXE F4 V2 Flight Controller is made with DJI Pilots in mind. This Deluxe FC packs a 16MB Blackbox, Barometer, 2 UARTs, and BEC into a mini-sized 20x20 board with 3-6S capabilities!

JHEMCU NOXE F411 V2 DJI Flight Controller - Mini 20x20 - Deluxe

WREKD General

JHEMCU had a new flight controller aimed at those DJI pilots. This board comes feature-packed and ready for your next build.  The 20x20 form factor makes it a perfect fit for nearly any size drone and the 6s capability means that it will be able to keep up with your power needs. The deluxe version supports 16MB black box recording and features a barometer.
Check out our other 20x20 flight controllers, as well as the rest of our JHEMCU selection!
Specifications


Input Voltage: 3-6S LiPo


MCU: STM32F411


Gyro: MPU6000

OSD: Yes

UARTs: 2 Sets

ESC Connections: Yes

Firmware: JHEF411


BEC: 5V 3A, 10V 2A

Current Sensor: Yes
Buzzer: Yes
Barometer: Yes
Black Box: 16MB
DJI Compatible: Yes
Stack Size: 20x20

Dimensions: 27x27xmm


Weight: 4.5g


Includes

1x JHEMCU NOXE F4 V2 Deluxe 3-6S 20x20 Flight Controller


JHEMCU had a new flight controller aimed at those DJI pilots. This board comes feature-packed and ready for your next build.  The 20x20 form factor makes it a perfect fit for nearly any size drone and the 6s capability means that it will be able to keep up with your power needs. The deluxe version supports 16MB black b

JHEMCU NOXE F4 V2 Deluxe HD 3-6S 20x20 Flight Controller from WREKD Co.

JHEMCU NOXE F4 V2 Deluxe HD 3-6S 20x20 Flight Controller

FPVELITE

JHEMCU had a new flight controller aimed at those DJI pilots. This board comes feature-packed and ready for your next build. The 20x20 form factor makes it a perfect fit for nearly any size drone and the 6s capability means that it will be able to keep up with your power needs. The deluxe version supports 16MB black box recording and features a barometer.

JHEMCU NOXE F4 V2 Deluxe 3-6S 20x20 Flight Controller For DJI - For Sale At RaceDayQuads

BetaFPV

BetaFPV F4 1S 12A AIO Brushless Flight Controller - ELRS 2.4GHz

BETAFPV

F4 1S 12A AIO Brushless Flight Controller V2.2 is the default FC for Cetus X brushless whoop quadcopter, also great for 85mm whoop drones like Meteor85 and 3" toothpick drones like HX115 SE Toothpick Drone and HX115 LR Toothpick Drone. We updated the FC to V2.2 with BMI270 gyro and BB51 ESC hardware in place of ICM20689 gyro and BB21 ESC hardware.
Please click here to page F4 1S 12A AIO SPI ELRS V2.0 if you need information about it.
Tons of ExpressLRS items are available now!

Bullet Point


F4 1S 12A AIO Flight Controller is the best choice for building ultra-lightweight 3" toothpick drones like HX115 SE FPV Quad and 85mm whoop drones. Recommend Meteor85.
Most of the 1S flight controllers on the market come with 5A ESC by now, but this FC especially integrates 1S 12A ESC, providing more sufficient power for 3" toothpick drones or 85mm whoop drones.
Built-in current meter, 2 programmable RGB LEDs, and SPI ELRS or Frsky receiver. At the same time, all the pads are left for the external receivers with UART1 and UART2, for buzzers, etc.
Large pads are reserved for solder motor cables, this design will make solder easier.

Specification of FC

Item: F4 1S 12A AIO FC
Weight: 4.74 g (without power cable and BT2.0 connector)
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: BMI270 (SPI connection)
Firmware version: betaflight_4.3.1_BETAFPVF4SX1280 (ELRS) /betaflight_4.2.11_BETAFPVF411RX (Frsky)

OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: SPI ELRS 2.4G Receiver/SPI Frsky
Motor Pin Connector: 1.25mm Header Pins
Mounting Hole Size: 26mm x 26mm (suitable for whoop pattern mounting hole)
USB Port: SH1.0 4-Pin

Specification of 1S 12A ESC

Built-in ESC with 12A continuous and peak 25A current
Input voltage: 1S-2S
ESC firmware: C_X_30_48_V0.18.1.hex for Bluejay BB51 hardware
Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM

The Bluejay firmware could support the BB51 hardware now. Both ELRS and Frsky boards are powered by BB51 hardware. If you want to setup the ESC specification, please use the BLHeliSuite16714902A_Beta or ESC-Configurator.

ESC-Configurator: https://preview.esc-configurator.com/

Download BLHeliSuite16714902A_Beta here.
Download the Bluejay ESC firmware. Please choose C_X_30.HEX.

Note: Only SPI ELRS 2.4G version supports motor direction set through Betaflight Configurator and SPI Frsky version does not support it. BLHeli Configurator and Bluejay Configurator are invalid for the BB51 ESC (both versions).
Diagram for F4 1S 12A AIO FC
Below is the diagram for SPI ELRS 2.4G board.


Below is the diagram for SPI Frsky board.


The current meter is integrated on the FC board. Here is the configuration in Betaflight Configurator.

12A 1S ESC
Should we really need a 12A ESC for 1S drones? If it is a 65mm or 75mm Whoop drone-like Meteor65, 5A ESC is enough for all actions. But how about with 3" propellers and 1102/1202.5 motors? Still, want smooth and powerful flying actions? The 5A ESC has developed about 3 years ago and was designed for whoop drones with 0603/0802 motors. For the past year, the BETAFPV team has been cooperating with BLHeli author Steffen on the 12A 1S ESC for 3" toothpick drones. Finally, it is here!
SPI ELRS 2.4G RX
This board integrates the receiver with the most popular radio link ExpressLRS since 2021. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. Know more about the ExpressLRS project on Github or join the discussion in the Facebook Group.

This board is designed for long-range 3inch ultralight toothpick drones or 2S whoop drones. If you want to try ExpressLRS on 65mm/75mm whoop drones, please build it with our F4 1S FC board with a built-in SPI ExpressLRS receiver.
F4 1S 12A AIO V2.2 integrates SPI ELRS 2.4G RX. The configuration is as follows.

How to Bind with Betaflight FC with SPI ExpressLRS Receiver.
How to Bind with Betaflight FC with External ExpressLRS Receiver.
More details and discussion on Github about SPI ELRS receiver.
SPI Frsky RX
Come with the built-in SPI Frsky Receiver (CC2500 chip), F4 1S 12A AIO FC can be compatible with Futaba S-FHSS, Frsky D8, and D16 protocol. The default protocol is configured to Frsky D16 FCC out of the factory. Pilots could set up the protocol according to your own need in Betaflight Configurator.






Configuration


Protocol




FRSKY_D


Frsky D8



FRSKY_X


Frsky D16 FCC (ACCST 1.X version)




FRSKY_X_LBT


Frsky D16 LBT (ACCST 1.X version)




SFHSS


Futaba S-FHSS







How to Bind with Betaflight FC with SPI Frsky Receiver.
Betaflight Firmware and CLI
F4 1S 12A FC board comes with the default firmware betaflight_4.3.1_BETAFPVF4SX1280 (ELRS) or betaflight_4.2.11_BETAFPVF411RX (Frsky). The default firmware for SPI ELRS 2.4G RX version supports ELRS V2.0 RX.
Pay attention, For the SPI ELRS 2.4G version, ONLY the Betaflight firmware 4.3.0 and up start to support this BMI270 gyro. For the SPI Frsky version, DO NOT flash the other firmware. We have already built our own firmware betaflight_4.2.11_BETAFPVF411RX for SPI Frsky RX version to support BMI270 gyro. Please check the below link to download the firmware.
Download the firmware and CLI dump file for the F4 1S 12A FC board (ELRS and Frsky).
Bluejay ESC Firmware

F4 1S 12A flight controller with BB51 ESC hardware could flash the Bluejay ESC firmware now, which is based on BLHeli_S revision 16.7. With Bluejay ESC firmware, it supports bidirectional D-shot and RPM filtering in Betaflight, offers 24KHz, 48KHz, and 96KHz fixed PWM frequency for options, and custom start-up melodies. By using Bluejay ESC firmware on Cetus X and Meteor85 whoop drones with 1103 11000KV motors, the flight time is increasing effectively.

For pilots who want to flash Bluejay ESC firmware for F4 1S 12A FC, please use the BLHeliSuite16714902A_Beta or ESC-Configurator and download Bluejay ESC firmware C_X_30_.HEX from the below links.

ESC-Configurator: https://preview.esc-configurator.com/

Download BLHeliSuite16714902A_Beta here.
Download the Bluejay ESC firmware. Please choose C_X_30.HEX.


Note: Only SPI ELRS 2.4G version supports motor direction set through Betaflight Configurator and SPI Frsky version does not support it. BLHeli Configurator and Bluejay Configurator are invalid for the BB51 ESC (both versions).
Connecting External RX/HD Digital or Analog VTX
Both SPI ELRS 2.4G RX and SPI Frsky RX version support external HD digital VTX or Analog VTX. Please note that the board reserves an SBUS port and a UART port, which is available for the SBUS protocol receiver or other external receivers. You can refer to the below picture.

Recommend Parts
If you want to try the popular ExpressLRS receiver version for long-range performance, highly recommend you check the items for the ExpressLRS series.

Drones: Cetus X, 85mm whoop frame like Meteor85, Meteor85 HD, 3" toothpick drones
Battery: BT2.0 450mAh 1S 30C Battery, 450mAh 2S 45C Battery

Motor: 1102 18000KV motor, 1103 11000KV motor

Propeller: HQ3020 2-blade Props, 2020 4-blade Props


Package

1 * F4 1S 12A AIO FC
4 * Anti-vibration Rubber Dampers
4 * M2 x 10mm Screws
4 * M2 x 10mm Screws
4 * M2 Screw Nut
8 * PH-1.25 Connectors for Motor
1 * SH1.0 4-Pin Cable
1 * SH1.0 4-Pin to USB Type-C Adapter



F4 1S 12A AIO Brushless Flight Controller V2.2 is the default FC for Cetus X brushless whoop quadcopter, also great for 85mm whoop drones like Meteor85 and 3" toothpick drones like HX115 SE Toothpick Drone and HX115 LR Toothpick Drone. We updated the FC to V2.2 with BMI270 gyro and BB51 ESC hardware in place of ICM2068

F4 1S 12A AIO Brushless Flight Controller 2022

&nbspIf you want to try a bigger FPV drone than 65mm/75mm on 1S power, and still want smooth and powerful flying actions, this 12A&nbsp AIO FC V1.0&nbsp ELRS is definitely your best choice!

 If you want to try a bigger FPV drone than 65mm/75mm on 1S power, and still want smooth and powerful flying actions, this 12A  AIO FC V1.0  ELRS is definitely your best choice!

BetaFPV F4 1S 12A AIO Brushless Flight Controller - ELRS 2.4G V1.0

&nbspIf you want to try a bigger FPV drone than 65mm/75mm on 1S power, and still want smooth and powerful flying actions, this 12A&nbsp AIO FC V2&nbsp ELRS is definitely your best choice!

 If you want to try a bigger FPV drone than 65mm/75mm on 1S power, and still want smooth and powerful flying actions, this 12A  AIO FC V2  ELRS is definitely your best choice!

BetaFPV F4 1S 12A AIO Brushless Flight Controller - ELRS 2.4G V2.0

Diatone

Diatone Mamba F405 DJI MK2 40A 3-6S 30x30 Flight Controller Stack - F405 HD FC, F40 40A ESC






Description



MAMBA F405MK2 V2 Flight Controller ICM42688P
MCU: 168MHz STM32F405GYRO: ICM-42688-PTarget：FURYF4OSDOSD: YesBlacbox: 16M Flash MemoryBarometer: NoUarts: 3 SetI2C: YesF.Port: NoRSSI: YesBuzzer Pad: YesCURR Pad: YesESC Signal: 4 SetESC Soft: Dshot300/600ESC Telemetry: YesPower Led: YesLED Controller:BF LEDAIR UNIT Port: YesWIFI: NoVTX Switch: NoReceiver Protection: YesBEC Protection: YesTVS Protection: YesBEC:3.3V 0.5A&amp 5V 3A&amp 9V 3AInput: 3~6S Lipo (12.6~25.2V)Mounting size: 30.5mm/M3ESC SpecificationsMAMBA F40MK2Input voltage: 3~6S Lipo (12.6V~25.2V)Continue current:40A×4Burst current 50A (10S)BEC: NoTarget：BLHeli_S CH40SOFT: Dshot300/600TVS Protection: NoMOUNTING: 30.5mm/M3
MAMBA F50_BLSInput voltage: 3~6S Lipo (12.6V~25.2V)Continue current:50A×4Burst current 50A (10S)BEC: NoTarget：BLHeli_S CH40SOFT: Dshot300/600TVS Protection: NoMOUNTING: 30.5mm/M3












Description MAMBA F405MK2 V2 Flight Controller ICM42688P MCU: 168MHz STM32F405GYRO: ICM-42688-PTarget：FURYF4OSDOSD: YesBlacbox: 16M Flash MemoryBarometer: NoUarts: 3 SetI2C: YesF.Port: NoRSSI: YesBuzzer Pad: YesCURR Pad: YesESC Signal: 4 SetESC Soft: Dshot300/600ESC Telemetry: YesPower Led: YesLED Controller:BF LEDAIR 

Diatone Mamba Stack - F405 MK2 FC + F40 40A BLHeli_S ESC Gyro: ICM42688P

Diatone Mamba Stack - F405 MK2 FC + F40 40A BLHeli_S ESC Gyro: ICM4268

The&nbspDiatone Mamba F405 DJI Mini&nbspStack&nbspbrings BIG power all in a mini 20x20 mounting size! This stack can push 40A all while bringing you the latest features!&nbspThe built-in plug-in allows you to easily connect to the&nbspDJI FPV Air System.&nbsp

The Diatone Mamba F405 DJI Mini Stack brings BIG power all in a mini 20x20 mounting size! This stack can push 40A all while bringing you the latest features! The built-in plug-in allows you to easily connect to the DJI FPV Ai

Diatone Mamba Stack - DJI F405 MK2 FC + F40 40A 128K ESC - Mini 20x20

JHEMCU GSF405A 1S-2S AIO F4 Flight Controller - 5A ESC, ELRS 2.4GHz Rx

The&nbspJHEMCU GS405A AIO&nbspfeatures an F4 FC and a 5A ESC with built-in ELRS 2.4GHz receiver. This is an ultra-light 3.3g brushless AIO flight controller with 25.5x25.5mm mounting pattern!!&nbspThis FC can handle 5A of continuous current and up to 2S.

The JHEMCU GS405A AIO features an F4 FC and a 5A ESC with built-in ELRS 2.4GHz receiver. This is an ultra-light 3.3g brushless AIO flight controller with 25.5x25.5mm mounting pattern!! This FC can handle 5A of continuous current and up

JHEMCU AIO Board - GSF405A F4 FC + 5A 1-2S ESC w/ Built-in ELRS 2.4GHz Receiver

JHEMCU has done it again with this impressive 1-2S AIO featuring an ExpressLRS built-in RX!
Browse the rest of our Whoop AIO boards and the rest of our JHEMCU selection!
Specifications

Input Voltage: 1-2S
CPU: STM32F405
Gyro: MPU6000
OSD: AT7456E
Barometer: BMP280
Black box: 8MB
IIC: Support
BEC: 5V
UART: UART1 (ELRS), UART2 (external RC), UART3, UART4, UART6
Receiver: ELRS (CRSF), TBS (CRSF), SBUS, IBUS, DSM2, DSMX
Buzzer: Yes
Current Sensor: Yes

Protocol: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Continuous current: 5A
Firmware: BLHELI_S S_H_50_REV16_7.HEX
Mounting Pattern: 25x25 M2
Weight: 3.3 grams

Express LRS Receiver

Frequency: 2.4GHZ
Protocol: CRSF 
Firmware: DIY_2400_RX_ESP8285_SX1280

Includes

JHEMCU GSF405A 1-2S Toothpick/Whoop AIO Flight Controller w/ 8bit 5A ESC and ELRS 2.4GHz RX


JHEMCU has done it again with this impressive 1-2S AIO featuring an ExpressLRS built-in RX! Browse the rest of our Whoop AIO boards and the rest of our JHEMCU selection! Specifications Input Voltage: 1-2S CPU: STM32F405 Gyro: MPU6000 OSD: AT7456E Barometer: BMP280 Black box: 8MB IIC: Support BEC: 5V UART: UART1 (ELRS),

JHEMCU GSF405A 1-2S Toothpick/Whoop AIO Flight Controller w/ 8bit 5A ESC and ELRS 2.4GHz RX

JHEMCU GSF405A 1-2S Toothpick/Whoop AIO Flight Controller w/ 8bit 5A E

JHEMCU GSF405A is a 1-2S F4 AIO, which also integrates four-in-one brushless ESC and ELRS 2.4G receiver.It has 5 serial ports (UART1, UART2, UART3, UART4, UART6), one I2C port, and one SBUS interface. (The serialport used by SBUS is RX2), the built-in ELRS receiver is UART1 port, onboard a WS2812 LED light, and theWS28

JHEMCU GSF405A 1S-2S AIO F4 Flight Control W/ 5A ESC & ELRS 2.4G RX - 25.5×25.5mm

JHEMCU GSF405A 1-2S Toothpick/Whoop AIO Flight Controller w/ 8bit 5A ESC and ELRS 2.4GHz RX from WREKD Co.

JHEMCU GSF405A-BMI is a 1-2S F4 AIO that includes a 4in1 brushless ESC and ELRS 2.4G receiver. It possesses 5 UARTs (1-4, 6), an I2C port, and is SBUS compatible (RX2 port). Additionally, a built-in ELRS receiver is available on UART1 and WS2812 LED light is preinstalled on the board. Moreover, an 8MB black box, barometer, buzzer, and 5V supply camera interface are featured along with a reserved camera interface.

Specifications

CPU: STM32F405
Gyroscope/Accelerometer: BMI270
OSD: AT7456E
Barometer: BMP280
Black box: 8MB
IIC: support
BEC: 5V
UART: UART1 (ELRS), UART2 (external RC), UART3, UART4, UART6
USB: micro usb
Size: 25.5x25.5mm M2
Receiver: ELRS(CRSF), TBS(CRSF), SBUS, IBUS, DSM2, DSMX
Support programmable LEDs such as WS2812
Support buzzer
Built-in voltage, current sensor
Firmware: Betaflight_ 4.3.0_STM32F405.HEX (JHEF405PRO)
Weight: 3.3g

Receiver Specifications

Protocol: ELRS (ExpressLRS)
Frequency: 2.4GHZ
Working Agreement: CRSF(Betaflight)
Firmware: JHEMCU_EP24S_2400_RX-2.2.0.bin

ESC Specifications

Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 1S-2S Lipo
Continuous current: 5A
Firmware: BLHELI_S S_H_50_REV16_7.HEX

Includes

1 x GSF405A-BMI board
1 x 2.4G Antenna
1 x 2.0MM plug wire
1 x 470UF/10V capacitor
4 x M2*6.5MM shock-absorbing ball
1 x 2S series board


JHEMCU GSF405A-BMI is a 1-2S F4 AIO that includes a 4in1 brushless ESC and ELRS 2.4G receiver. It possesses 5 UARTs (1-4, 6), an I2C port, and is SBUS compatible (RX2 port). Additionally, a built-in ELRS receiver is available on UART1 and WS2812 LED light is preinstalled on the board. Moreover, an 8MB black box, barome

JHEMCU GSF405A 1S-2S AIO F4 Flight Control W/ 5A ESC & ELRS 2.4G RX - 25.5×25.5mm from WREKD Co.

Matek F405-miniTE 20x20 Flight Controller

MATEK

Another solid choice in the Matek F405-miniTE 20x20 Flight Controller by a company that leads the pack when it comes to quality and performance.
Check out all our 20x20 FCs as well as the entire Matek selection!
Features

F405 has 1MB flash which can run with ArduPilot.  even with INAV firmware.
Redesigned target MATEKF405TE support 8x bi-directional DSHOT.
Support DJI air unit PnP, and a 10V BEC for DJI OSD or analog VTX
Compared with F722-miniSE 8motors or 6motor+2servos, F405-miniTE supports 8motors+3servos in INAV/BF multirotor mixer
Convertible 20mm to 30.5mm mounting

Specifications

Input: 6~30V (2~6S LiPo)
MCU: STM32F405RGT6
IMU: ICM42688-P

OSD: AT7456E
Baro: Goertek SPL06-001 (I2C)
Blackbox: 16M-byte Flash memory
UARTs: 6
PWM outputs: 12 (8 Dshot)
I2C: 1
ADC: 4 (VBAT, Current, RSSI, Airspeed)
Current Sensor: No
PINIO: 2
BEC: 5V 1.7A &amp 10V 1.4A
Mounting Pattern: 20x20 M2/M3, 30X30 M3
Weight: 5g

Includes

1x Matek F405-miniTE 20x20 Flight Controller
1x 20mm to 30mm conversion plate(blue PCB)
6x Silicon grommets M4 to M3
6x Brass grommets M3 to M2
1x SH1.0_8pin cable 5cm (including 2x 8pin connectors) for 4in1 ESC
1x SH1.0_6pin to GH1.25_8pin cable 8cm for DJI Air Unit


The Matek F405-miniTE 20x20 Flight Controller is yet another solid addition to our 20x20 lineup. Matek leads the pack when it comes to 20x20 quality and performance.

Matek F405-miniTE 20x20 Flight Controller for Sale - RaceDayQuads

Another solid choice in the Matek F405-miniTE 20x20 Flight Controller by a company that leads the pack when it comes to quality and performance.
Check out all our 20x20 FCs as well as the entire Matek selection!
Features

F405 has 1MB flash which can run with ArduPilot.  even with INAV firmware.
Redesigned target MATEKF405TE support 8x bi-directional DSHOT.
Support DJI air unit PnP, and a 10V BEC for DJI OSD or analog VTX
Compared with F722-miniSE 8motors or 6motor+2servos, F405-miniTE supports 8motors+3servos in INAV/BF multirotor mixer
Convertible 20mm to 30.5mm mounting

Specifications

Input: 6~30V (2~6S LiPo)
MCU: STM32F405RGT6
IMU: ICM42688-P

OSD: AT7456E
Baro: Goertek SPL06-001 (I2C)
Blackbox: 16M-byte Flash memory
UARTs: 6
PWM outputs: 12 (8 Dshot)
I2C: 1
ADC: 4 (VBAT, Current, RSSI, Airspeed)
Current Sensor: No
PINIO: 2
BEC: 5V 1.7A &ampamp 10V 1.4A
Mounting Pattern: 20x20 M2/M3, 30X30 M3
Weight: 5g

Includes

1x Matek F405-miniTE 20x20 Flight Controller
1x 20mm to 30mm conversion plate(blue PCB)
6x Silicon grommets M4 to M3
6x Brass grommets M3 to M2
1x SH1.0_8pin cable 5cm (including 2x 8pin connectors) for 4in1 ESC
1x SH1.0_6pin to GH1.25_8pin cable 8cm for DJI Air Unit


Another solid choice in the Matek F405-miniTE 20x20 Flight Controller by a company that leads the pack when it comes to quality and performance. Check out all our 20x20 FCs as well as the entire Matek selection! Features F405 has 1MB flash which can run with ArduPilot.  even with INAV firmware. Redesigned target MATEKF

Matek F405-miniTE 20x20 Flight Controller from WREKD Co.

The&nbspF405 MiniTE Flight Controller&nbspwas designed to be smaller and lighter than its bigger brother, and the 20x20mm mount allows for more space to work with on your build.

The F405 MiniTE Flight Controller was designed to be smaller and lighter than its bigger brother, and the 20x20mm mount allows for more space to work with on your build.

MATEKSYS F405-MiniTE Flight Controller - Mini 20x20

This new F405 board from Matek is packed with a 3rd Gen. 8K Gyro, Barometer, BFOSD, 16M Blackbox Flash Memory, and a convenient 20x20mm to 30x30mm adapter board which supports M2 or M3 hardware. It also has Dual BEC 5V and 10V to properly supply power to more amp hungry devices like the DJI Air Unit. And for those that

Matek F405-MINITE - 30x30mm or 20x20mm w/ 32K Gyro, Barometer, and BetaFlight OSD

JHEMCU NOXE F4 V2 Standard 3-6S 20x20 Flight Controller For DJI

New 20x20mm flight controller line from JHEMCU available as standard and deluxe.Deluxe verion features blackbox and barometer. Standard: No BarometerDeluxe: With Baromete Check out all our 20x20mm Flight Controllers and the rest of our JHEMCU Products! Specifications: JHEMCU F4 NOXE 3-6S 20*20 Flight Controller for DJI

JHEMCU NOXE F4 V2 Standard 3-6S V2 Flight Controller For DJI - 20x20mm

The&nbspJHEMCU NOXE F4 V2 Flight Controller&nbspis made with DJI Pilots in mind. This standard version FC packs 2 UARTs, and a BEC into a mini-sized 20x20 board with 3-6S capabilities!

The JHEMCU NOXE F4 V2 Flight Controller is made with DJI Pilots in mind. This standard version FC packs 2 UARTs, and a BEC into a mini-sized 20x20 board with 3-6S capabilities!

JHEMCU NOXE F411 V2 DJI Flight Controller - Mini 20x20 - Standard

GEPRC

GEPRC F411 35A Toothpick AIO Flight Controller - F411 FC, 35A 2S-6S ESC

I am glad to introduce a new member of GEP FC AIO, GEP-F4-35A,it is released now. GEP-F4-35A is developed on the basis of GEP-F4-20A. It can handle 35A continuous current and (40A burst), totally supports the 2-6S lipo battery.It can be used with 1204/1404/1507/1805/2004 motors and 2-5 inch propellers. Support OSD para

GEPRC GEP-F411-35A AIO F411 FC 35A 2-6S 8bit BLHeli_S ESC - 25.5x25.5mm

The&nbspGEPRC F411 35A Toothpick AIO can&nbsphandle 35A continuous current and (40A burst), supports 2-6S lipo batteries, and can be used with 1204/1404/1507/1805/2004 motors and 2-5 inch propellers!&nbsp

The GEPRC F411 35A Toothpick AIO can handle 35A continuous current and (40A burst), supports 2-6S lipo batteries, and can be used with 1204/1404/1507/1805/2004 motors and 2-5 inch propellers! 

GEPRC F411 35A Toothpick AIO - F411 FC + 35A 2S-6S BLS ESC


GEP-F4-35A is developed on the basis of GEP-F4-20A. It can handle 35A continuous current and (40A burst) and totally supports the 2-6S lipo battery. It can be used with 1204/1404/1507/1805/2004 motors and 2-5 inch propellers. It supports OSD parameter adjustments. And It’s only 8.8g ultra-lightweight. With 25.5mm x 25.5mm mounting holes, this AIO is suitable for most of the frames on the market.
Check out all our whoop flight controllers, and our GEPRC products!

Features

BLheli_ S 35A ESC, supports 2-6S LIPO battery input, it can handle 35A continuous current (40A burst), with a current meter.
Mainstream STM32F411 FC runs stably.

BMI270 gyroscope with 8K sampling frequency.

External Buzzer: Support
LED Control: Support
The overall weight is about 8.8g



Specifications

Model Name: GEP-F411-35A AIO
MCU: STM32F411
IMU: BMI270 gyro/accelerometer (SPI)
FC Firmware target: GEPRC_F411_AIO
OSD: BetaFlight OSD w/ AT7456E chip
Baro: NO
Current Monitoring: Yes
Betaflight OSD: Yes
External Buzzer: Yes supported
LED: Yes Supported
USB Port: MicroUSB
BEC Output: 5V@1A
Integrated LC Filter
ESC MCU: 8BB21F16G
Continuous current: 35A
Peak current: 40A(10s)
Input: 2-6S lipo
Supports Dshot300/600, Oneshot, Multishot
Current meter: 210
Target: G_H_30 BLS
Size: 32x32mm board,25.5mm mounting holes (M2)
Installing Hole: 25.5×25.5mm, M2

Manual PDF
Includes

1 x GEP-F4-35A-AIO
1 x XT30-7CM-18AWG cables
1 x 35V220UF capacitance
8 x M2*6.5mm Damping rings




GEP-F4-35A is developed on the basis of GEP-F4-20A. It can handle 35A continuous current and (40A burst) and totally supports the 2-6S lipo battery. It can be used with 1204/1404/1507/1805/2004 motors and 2-5 inch propellers. It supports OSD parameter adjustments. And It’s only 8.8g ultra-lightweight. With 25.5mm x 25.

GEPRC F411 2-6S AIO Toothpick / Whoop Flight Controller w/ 35A 4in1 ESC

GEPRC F411 2-6S AIO Toothpick / Whoop Flight Controller w/ 35A 4in1 ES

Model: GEP-F4-35A
 	MCU: STM32F411
 	IMU: BMI270/accelerometer(SPI)
 	OSD: Betaflight OSD w/ AT7456Ev
 	ESC MCU: BB21F16G
 	Continue Current: 35A
 	Input Voltage: 2~6S (LIPO Battery)
 	ESC Protocol: Dshot300/600,Oneshot,Multishot
 	Size: 32x32mm Board
 	Mount Holes: 25.5x25.5mm
 	Weight: 8.8g

Model: GEP-F4-35A  MCU: STM32F411  IMU: BMI270/accelerometer(SPI)  OSD: Betaflight OSD w/ AT7456Ev  ESC MCU: BB21F16G  Continue Current: 35A  Input Voltage: 2~6S (LIPO Battery)  ESC Protocol: Dshot300/600,Oneshot,Multishot  Size: 32x32mm Board  Mount Holes: 25.5x25.5mm  Weight: 8.8g

GEP-F411-35A AIO (F411 FC 35A 2-6S 8bits BLS ESC 25.5mm) - GEPRC

GEP-F411-35A AIO (F411 FC 35A 2-6S  8bits BLS ESC 25.5mm)

GEPRC F411 2-6S AIO Toothpick / Whoop Flight Controller w/ 35A 4in1 ESC from WREKD Co.

Skystars

SkyStars F4 & KO55 3-6S ESC 30x30 Fly Tower Flight Controller Stack   

SkyStars

The SkyStars F4+ KO55 Blheli_S Fly Tower Stack features the SkyStars F4 flight controller, as well as the KO55 55A 4-in-1 ESC to give your multirotor full power!

SkyStars Fly Tower Stack - F4 FC + KO55 55A 3-6S 4-in-1 BLHeli_S ESC - 30x30

Skystars F4 F405 Flight controller and 55A Blheli-S ESC fly tower stack Check out all our Stacks and the rest of our Skystars Products! Specifications: MCU: STM32F405 IMU: MPU6000 OSD: AT7456E Blackbox: 8MB 6X Uarts(1 2 345 6) WS2812 led Strip: YES Baro: No Beeper: YES BEC: 5V/3A cont FC Firmware: Betaflight FC Target:

Skystars F4 F405 Flight controller and 55A Blheli-S ESC fly tower stack - 30x30mm

EMAX

EMAX Babyhawk II HD Part B - AIO Flight Controller ESC Board

This Emax AIO Flight Controller + ESC is a replacement part for the EMAX BabyHawk II HD Freestyle! Check out all our Whoop Style AIO Flight Controllers and the rest of our Emax Babyhawk II Collection! Specifications: Brand Name: Emax Input Voltage: 2-4S Lipo Firmware:STM32F411 Firmware Gyroscope: MPU6000 Onboard: 25A B

EMAX BabyHawk II HD BLHeli_S F4 2-4S 25A Whoop Style AIO

This Emax AIO Flight Controller + ESC is a replacement part for the&nbspEMAX BabyHawk II HD Freestyle RTF.

This Emax AIO Flight Controller + ESC is a replacement part for the EMAX BabyHawk II HD Freestyle RTF.

EMAX BabyHawk II HD BLHeli_S F4 2-4S 25A  AIO FC + ESC

HAKRC

HAKRC F4530D 3-6S HD Flight Controller for DJI

The HAKRC F4530D Flight Controller provides great power all in a 30.5x30.5 mounting pattern. Features MPU6000, MATEK405 4.1 Betaflight, STM32F405RGT6 processor, and other cool features! Compatible with DJI Digital FPV.

Happymodel Crazybee F4 Lite 1S Whoop Flight Controller for Mobula 6

The Happymodel CrazyBee F4 Lite Flight Controller brings lots of power in a small package. This 4-in-1 FC comes with an integrated receiver (FrSky), ESC, and an onboard 5.8GHz VTX!

Happymodel Crazybee F4 Lite 1S Whoop Flight Controller - Frsky

Replacement flight controller for the popular Happymodel Mobula 6 or any 1S build Checkout our Mobula 6 parts and our full collection of Happymodel Products! Specifications Flight Controller (Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR (Flysky SPI RX version) CRAZYBEE F4 Lite Flys

HappyModel Crazybee F4 Lite 1S Whoop Flight Controller for Mobula 6 - Frsky

The Happymodel CrazyBee F4 Lite Flight Controller brings lots of power in a small package. This 4-in-1 FC comes with an integrated receiver (Flysky), ESC, and an onboard 5.8GHz VTX!