FPV Quad Parts

Peripherals and Replacement Parts

Equipment

Equipment Peripherals

Build Page Parts

Build Parts Equipment

Pre-Built Quads and Kits 

Build Page Parts Overflow

Build Parts Equipment Overflow

Compatibility Categories

NewBeeDrone

NewBeeDrone BeeCeiver 2.4Ghz ELRS Diversity TCXO Receiver

NewBeeDrone BeeCeiver ExpressLRS 2.4Ghz Diversity with TCXO Oscillator Micro Receiver
Discover the NewBeeDrone BeeCeiver ExpressLRS 2.4Ghz Diversity Micro Receiver, a marvel in compact and efficient design. Equipped with the industry-leading TCXO (temperature-compensated crystal oscillator), this micro receiver ensures unmatched signal stability and precision for an elevated flight experience.Despite its smaller size, the BeeCeiver does not compromise on performance. It utilizes ExpressLRS 2.4ghz open-source firmware for a responsive and extended range, supported by the ESP8285 MCU and SX1280IMLTRT RF Chip with Skyworks RFX2401C PA LNA. This powerful combination delivers a reliable and far-reaching RF link, enhancing control and connectivity.Ease of use is at the forefront of the BeeCeiver's design. Quick and simple binding, coupled with convenient in-craft WiFi firmware updates, makes setup and maintenance hassle-free. It's designed to integrate effortlessly into any drone setup, prioritizing both functionality and user experience.In essence, the NewBeeDrone BeeCeiver is not just an addition to your drone - it's a significant upgrade, pushing the boundaries of what you can achieve in the sky. Compact, powerful, and user-friendly, it sets a new standard in drone receiver technology. 
Specification:

Type: ISM
MCU: ESP8285
RF Chip: SX1280
Telemetry RF power: 20dbm
Antenna: 60mm 2.4ghz x2 or T-Antenna IPEX3 x 2
Frequency Range: 2.404 - 2.479 Ghz
Working voltage: 4.5-5.5v
Weight: 1.6g (Including two antenna)
Dimension: 17mm*9.5mm*3mm
Firmware Version: ExpressLRS v3.x
FW Target: NewBeeDrone Diversity 2.4Ghz RX
Bus interface: CRSF
Extend Interface：UART
TCXO Oscillator

Include:
1x NewBeeDrone BeeCeiver ExpressLRS 2.4Ghz Diversity with TCXO Oscillator Micro Receiver2x NewBeeDrone BeeT-Antenna2x NewBeeDrone 2.4G Replacement Receiver Antennas 60mm4x Silicone wire 2x 3M double side tape
Binding: 
Power on 3-times will trigger the receiver get into binding mode. 
Firmware:
ExpressLRS web-flasherUnder NewBeeDrone brand and the target name is NewBeeDrone Diversity 2.4Ghz RX

NewBeeDrone BeeCeiver ExpressLRS 2.4Ghz Diversity with TCXO Oscillator Micro Receiver Discover the NewBeeDrone BeeCeiver ExpressLRS 2.4Ghz Diversity Micro Receiver, a marvel in compact and efficient design. Equipped with the industry-leading TCXO (temperature-compensated crystal oscillator), this micro receiver ensures

NewBeeDrone BeeCeiver ELRS 2.4Ghz Diversity with TCXO Oscillator Micro Receiver

NewBeeDrone BeeCeiver ELRS 2.4Ghz Diversity with TCXO Oscillator Micro

NewBeeDrone BeeCeiver ExpressLRS 2.4Ghz Diversity with TCXO Oscillator Micro Receiver
Discover the NewBeeDrone BeeCeiver ExpressLRS 2.4Ghz Diversity Micro Receiver, a marvel in compact and efficient design. Equipped with the industry-leading TCXO (temperature-compensated crystal oscillator), this micro receiver ensures unmatched signal stability and precision for an elevated flight experience.Despite its smaller size, the BeeCeiver does not compromise on performance. It utilizes ExpressLRS 2.4ghz open-source firmware for a responsive and extended range, supported by the ESP8285 MCU and SX1280IMLTRT RF Chip with Skyworks RFX2401C PA LNA. This powerful combination delivers a reliable and far-reaching RF link, enhancing control and connectivity.Ease of use is at the forefront of the BeeCeiver&#39s design. Quick and simple binding, coupled with convenient in-craft WiFi firmware updates, makes setup and maintenance hassle-free. It&#39s designed to integrate effortlessly into any drone setup, prioritizing both functionality and user experience.In essence, the NewBeeDrone BeeCeiver is not just an addition to your drone - it&#39s a significant upgrade, pushing the boundaries of what you can achieve in the sky. Compact, powerful, and user-friendly, it sets a new standard in drone receiver technology. 
Specification:

Type: ISM
MCU: ESP8285
RF Chip: SX1280
Telemetry RF power: 20dbm
Antenna: 60mm 2.4ghz x2 or T-Antenna IPEX3 x 2
Frequency Range: 2.404 - 2.479 Ghz
Working voltage: 4.5-5.5v
Weight: 1.6g (Including two antenna)
Dimension: 17mm*9.5mm*3mm
Firmware Version: ExpressLRS v3.x
FW Target: NewBeeDrone Diversity 2.4Ghz RX
Bus interface: CRSF
Extend Interface：UART
TCXO Oscillator

Include:
1x NewBeeDrone BeeCeiver ExpressLRS 2.4Ghz Diversity with TCXO Oscillator Micro Receiver2x NewBeeDrone BeeT-Antenna2x NewBeeDrone 2.4G Replacement Receiver Antennas 60mm4x Silicone wire 2x 3M double side tape
Binding: 
Power on 3-times will trigger the receiver get into binding mode. 
Firmware:
ExpressLRS web-flasherUnder NewBeeDrone brand and the target name is NewBeeDrone Diversity 2.4Ghz RX

NewBeeDrone BeeCeiver ExpressLRS 2.4Ghz Diversity with TCXO Oscillator Micro Receiver from WREKD Co.

NewBeeDrone BeeCeiver ExpressLRS 2.4Ghz Diversity with TCXO Oscillator Micro Receiver

Receiver Type

The radio receiver takes the inputs from your radio and sends them to your flight controller. Your receiver will need to be compatible with your radio or radio module. Beginners should get an ELRS receiver for the best range and price point. Learn more about radios and receivers.

Receivers

TBS Crossfire Nano RX

Team Black Sheep

Welcome one of the best reliable link receivers you will find on the market today! The TBS Crossfire Nano RX! TeamBlackSheep has taken the crossfire receiver and slammed it down in to the smallest receiver we have ever seen for a long range system. Pair this receiver with your mini quad your micro quad your whoop quad or any of your fixed wing airplanes and go further than you have ever have before! Get yours today!
Specifications

Weight: 0.5g (receiver only)
Size: 11mm x 18mm
Requires: Firmware V2.25

Includes

1x TBS Crossfire Nano Receiver
1x TBS Crossfire Micro Antenna
1x Spare shrink tube
6x 30awg silicon connection wires (2 black, 2 red, 1 white, 1 yellow)
1 x pin header 1x4

Wiring Diagram


Welcome one of the best reliable link receivers you will find on the market today! The TBS Crossfire Nano RX! TeamBlackSheep has taken the crossfire receiver and slammed it down in to the smallest receiver we have ever seen for a long range system. Pair this receiver with your mini quad your micro quad your whoop quad 

Nano 915MHz Receiver For Crossfire Protocol

Team BlackSheep

The TBS Crossfire Nano Rx (Special Edition).

TBS is stepping up the Long Range / UHF game, with no competition in sight! With the TBS Crossfire Nano RX, we condense two years of engineering experience, listening to our customer requirements, and pushing ourselves to the maximum (or in this case

TBS Crossfire Nano Rx (SE) w/ Immortal T V2 Antenna

<p>TBS is stepping up the Long Range / UHF game, with no competition in sight! With the TBS Crossfire Nano RX, we condense two years of engineering experience, listening to our customer requirements, and pushing ourselves to the maximum (or in 

TBS Crossfire Nano Rx

Team BlackSheep TBS Crossfire Nano RX - 3 Pack TBS Crossfire nano RX for people who want to save space and solder. Full range, designed specifically for mini- and micro-quads! TBS is stepping up the Long Range / UHF game, with no competition in sight! With the TBS Crossfire Nano RX we condense 2 years of engineering ex

3 Pack Team BlackSheep TBS Crossfire Nano RX

TBS is stepping up the Long Range / UHF game, with no competition in sight! With the TBS Crossfire Nano RX, we condense two years of engineering experience, listening to our customer requirements, and pushing ourselves to the maximum (or in this case, the minimum!). The end result is a full range receiver, at the smallest size of any receiver in the industry (yes, it's smaller than the XM+).
Specifications

Weight: 0.5g (receiver only)
Size: 11mm x 18mm
Requires: Firmware V2.24

Includes

1x TBS Crossfire Nano Receiver
1x TBS Crossfire Micro Receiver Antenna
1x TBS Immortal-T Antenna
1x Spare shrink tube
6x 30awg silicon connection wires (2 black, 2 red, 1 white, 1 yellow)
1 x pin header 1x4

Resources

TBS Crossfire - RED Declaration of Conformity
Quickstart Guide / Manual


TBS Crossfire Nano Rx (Special Edition) TBS is stepping up the Long Range / UHF game, with no competition in sight! With the TBS Crossfire Nano RX, we condense two years of engineering experience, listening to our customer requirements, and pushing ourselves to the maximum (or in this case, the minimum!). The

TBS Crossfire Nano Rx (Special Edition)

TBS Crossfire Nano Rx (Special Edition) DroneRacingParts.com

TBS Crossfire Nano RX is for people who want to save space and solder. Full range, designed specifically for mini- and micro-quads!
Check out the rest of out TBS Products and all our receivers!
Features
TBS is stepping up the Long Range / UHF game, with no competition in sight! With the TBS Crossfire Nano RX, we condense two years of engineering experience, listening to our customer requirements, and pushing ourselves to the maximum (or in this case, the minimum!). The end result is a full range receiver, at the smallest size of any receiver in the industry (yes, it's smaller than the XM+).

Specifications

Weight: 0.5g (receiver only)
Size: 11mm x 18mm
Requires: Firmware V2.24
Quickstart Guide / Manual

Includes

1x TBS Crossfire Nano Receiver
1x TBS Crossfire Micro Receiver Antenna
1x Spare shrink tube
6x 30awg silicon connection wires (2 black, 2 red, 1 white, 1 yellow)
1 x pin header 1x4


TBS Crossfire Nano RX is for people who want to save space and solder. Full range, designed specifically for mini- and micro-quads! Check out the rest of out TBS Products and all our receivers! Features TBS is stepping up the Long Range / UHF game, with no competition in sight! With the TBS Crossfire Nano RX, we conden

TBS Crossfire Nano 900MHz Receiver w/ CRSF Micro Antenna

RadioMaster

RadioMaster RP4TD ELRS 2.4GHz Diversity Receiver

Featuring dual-channel 2.4GHz radios, the RP4TD excels in signal sensitivity, signal-to-noise ratio, and overall performance due to its optimized circuit design. The reliable DCDC power supply circuit ensures lower operating temperatures during extended usage. Additionally, the dual TCXO contributes to the utmost frequ

HOBBYPORTER

Featuring dual-channel 2.4GHz radios, the RP4TD excels in signal sensitivity, signal-to-noise ratio, and overall performance due to its optimized circuit design. The reliable DCDC power supply circuit ensures lower operating temperatures during extended usage. Additionally, the dual TCXO contributes to the utmost frequency stability and makes the RP4TD a leader in its class. The RP4TD features built in WIFI, allowing you to wirelessly upgrade firmware to configure the receiver via the built-in WebUI with your PC or mobile phone.Suitable for drones and fixed-wing models, the receiver can be installed in virtually any application that requires a serial receiver!
Check out the rest of our RC receivers and all our RC transmitters, modules, and accessories!
Features

Dual TCXO (temperature compensated crystal oscillator)
The TCXO ensures high stability and accuracy in frequency control, compensating for temperature variations. This results in consistent and reliable signal reception, even in extreme temperature conditions. It also reduces frequency drift over time, providing long-term frequency stability and preventing signal degradation. In our testing, we found that two TCXOs offer better advantages in true diversity receivers.




Specifications

Item: RP4TD ExpressLRS 2.4GHz Diversity Receiver
Type: ISM
MCU: ESP32
RF Chip: SX1281 x 2
Antenna: 65mm 2.4GHz T Antenna x 2
Frequency Range: 2.4GHz
Maximum Refresh Rate: 500Hz / F1000Hz
Telemetry RF Power: Max 2x 100mW
Working Voltage: DC 4.5-12.0V
Weight: 1.4g (without antenna)
Dimension: 23.7x16.3x4.0mm
Firmware Version: ExpressLRS V3.3.0 pre-installed
FW Target: RadioMaster RP4TD 2400 RX
Bus interface: CRSF
Extend interface: UART


Includes

1x RadioMaster RP4TD ExpressLRS 2.4GHz Nano Receiver
1x CRSF wire
3x Heat-Shrinkable Tube
2x 65mm 2.4GHz T Antenna (Installed on receiver)
1x User Manual

 

RadioMaster RP4TD 2.4GHz ELRS Nano Diversity Receiver

RadioMaster RP4TD 2.4GHz ELRS Nano Diversity Receiver from WREKD Co.

RP4TD ExpressLRS 2.4ghz Diversity ReceiverSpecificcations:Type: ISMMCU: ESP32RF Chip: SX1281 x 2Antenna: 65mm 2.4ghz T Antenna x 2Frequency Range: 2.4GHzMaximum receive refresh rate: 500Hz / F1000HzWorking voltage: 5VWeight: 1.4g(without antenna)Dimension: 23.7mm*16.3mm*4.0mmFirmware Version: ExpressLRS v3.3.0 pre-installedFW Target: RadioMaster RP4TD 2400 RXBus interface: CRSFExtend interface : UARTDual TCXO (temperature compensated crystal oscillator)Package Includes:1 * RP4TD ExpressLRS 2.4ghz Diversity Receiver1 * CRSF wire3 * Heat-Shrinkable Tube2 * 65mm 2.4Ghz T Antenna (Installed on receiver)1 * User Manual

The best quality First Person View equipment. Free or discounted shipping on all orders.Drone Racing, RC Airplanes, FPV Cameras, FPV Goggles, Video Transmitters, RC Quads, Drone Antennas, Lipo Batteries, and Ground Station Equipment.All available for amateurs, schools, hobbyists, government, and wholesale buyers.

RadioMaster RP4TD ExpressLRS 2.4ghz Nano Receiver - RMRC

RadioMaster RP4TD ELRS 2.4ghz Diversity Nano Receiver

NewBeeDrone BeeCeiver Frsky V2 Receiver



Instruction Video:


The second generation of the Beeceiver RX is here! This FrSky compatible receiver is even smaller than its predecessor to be compatible with even more tiny builds when space is so tight. Even though this unit is our smallest yet, the input voltage range is large! And if you need inverted or un-inverted SBus signal, this unit has you covered! With the User Instruction Manual, setup and use is a breeze! Check out the rest of our NewBeeDrone receivers.
New Features:

Diversity
Multi Protocol (Frsky D16 &amp D8. Futaba s-fhss.)
Inverted &amp un-inverted S-Bus signal switchable


Specifications

Dimension: 16*11*5.4mm (L*W*H)
Weight: 0.91g
Operating Voltage Range: 3~10V

Instructions for Use
 


Instruction Video: The second generation of the Beeceiver RX is here! This FrSky compatible receiver is even smaller than its predecessor to be compatible with even more tiny builds when space is so tight. Even though this unit is our smallest yet, the input voltage range is large! And if you need inverted or un-invert

NewBeeDrone BeeCeiver Frsky V2 Compatible Receiver



Instruction Video:


The second generation of the Beeceiver RX is here! This FrSky compatible receiver is even smaller than its predecessor to be compatible with even more tiny builds when space is so tight. Even though this unit is our smallest yet, the input voltage range is large! And if you need inverted or un-inverted SBus signal, this unit has you covered! With the User Instruction Manual, setup and use is a breeze! Check out the rest of our NewBeeDrone receivers.
New Features:

Diversity
Multi Protocol (Frsky D16 &ampamp D8. Futaba s-fhss.)
Inverted &ampamp un-inverted S-Bus signal switchable


Specifications

Dimension: 16*11*5.4mm (L*W*H)
Weight: 0.91g
Operating Voltage Range: 3~10V

Instructions for Use
 


NewBeeDrone BeeCeiver Frsky V2 Compatible Receiver from WREKD Co.

The second generation of the Beeceiver RX is here! This FrSky compatible receiver is even smaller than its predecessor to be compatible with even more tiny builds when space is so tight. Even though this unit is our smallest yet, the input voltage range is large! And if you need inverted or un-inverted SBus signal, this unit has you covered! With the User Instruction Manual, setup and use is a breeze! Check out the rest of our NewBeeDrone receivers.New Features:DiversityMulti Protocol (Frsky D16 &amp D8. Futaba s-fhss.)Inverted &amp un-inverted S-Bus signal switchableSpecificationsDimension: 16*11*5.4mm (L*W*H)Weight: 0.91gOperating Voltage Range: 3~10V

The second generation of the Beeceiver RX is here! This FrSky compatible receiver is even smaller than its predecessor to be compatible with even more tiny builds when space is so tight. Even though this unit is our smallest yet, the input voltage range is large! And if you need inverted or un-inverted SBus signal, thi

NewBeeDrone BeeCeiver Frsky V1 Receiver



From deep inside the hive, our bee scientists have been working madly to bring you a receiver not only incredibly small in size, light enough to seem almost non-existent, and affordable with just the right amount of features you would want for all micro sized drones.The NewBeeDrone Beeceiver is our latest and greatest addition to the NewBeeDrone line up of small yet awesome hardware. Aimed at being the perfect receiver for any micro sized quad, This is possible thanks to it weighing less then 1 gram, making it almost unBEElevable!
Features

Ultra mini size and light weight
Support Frsky telemetry
SBUS signal output
IPEX connector, replaceable antennas

Specifications

Dimension: 16*11*5.4mm (L*W*H)
Weight: 0.91g
Number of channels:D8 8Channel
Operating Voltage Range: 3~10V

**Important note:  This RX only does traditional Sbus, meaning the FC it is used on must have an inverter in order to see the signal.


From deep inside the hive, our bee scientists have been working madly to bring you a receiver not only incredibly small in size, light enough to seem almost non-existent, and affordable with just the right amount of features you would want for all micro sized drones.The NewBeeDrone Beeceiver is our latest and greatest 

NewBeeDrone BeeCeiver Frsky Compatible Receiver V1 from WREKD Co.

NewBeeDrone BeeCeiver Frsky Compatible Receiver V1

NewBeeDrone Beeceiver DSM V2 Receiver

After creating one of the best micro receivers on the market, we went back to the lab and improved the range by almost double! By using diversity antennas (The world&#39s smallest diversity DSM compatible receivers) not only are you getting better range, but your getting a more reliable signal in tougher RF environments. We also made it smaller and lighter making it and even better choice for current micro brushed and brushless whoops. 
Binding Instruction:

Power on receiver
Push bind button once - (LED will blink red/blue)
Bind to Radio - Done!

Features

Ultra mini size and light weight
Serial signal output
IPEX connector, replaceable antennas

Specifications

Dimension: 16*11*5.4mm (L*W*H)
Weight: 0.78g (including dual antenna)
Compatible Protocols: DSMX / DSM2
Operating Voltage Range: 3~10V

Includes

Beeceiver V2
Silicone Wires
Heatshrink


After creating one of the best micro receivers on the market, we went back to the lab and improved the range by almost double! By using diversity antennas (The world's smallest diversity DSM compatible receivers) not only are you getting better range, but your getting a more reliable signal in tougher RF environments. 

NewBeeDrone Beeceiver DSM V2 Compatible Micro Receiver from WREKD Co.

NewBeeDrone Beeceiver DSM V2 Compatible Micro Receiver

After creating one of the best micro receivers on the market, we went back to the lab and improved the range by almost double! By using diversity antennas (The world's smallest diversity DSM compatible receivers) not only are you getting better range, but your getting a more reliable signal in tougher RF environments. We also made it smaller and lighter making it and even better choice for current micro brushed and brushless whoops. 
Binding Instruction:

Power on receiver
Push bind button once - (LED will blink red/blue)
Bind to Radio - Done!

Features

Ultra mini size and light weight
Serial signal output
IPEX connector, replaceable antennas

Specifications

Dimension: 16*11*5.4mm (L*W*H)
Weight: 0.78g (including dual antenna)
Compatible Protocols: DSMX / DSM2
Operating Voltage Range: 3~10V

Includes

Beeceiver V2
Silicone Wires
Heatshrink


NewBeeDrone BeeCeiver Flysky Receiver

After creating one of the best micro receivers on the market, we went back to the lab and improved the range by almost double! By using diversity antennas (The world&#39s smallest diversity Flysky compatible receivers)not only are you getting better range, but your getting a more reliable signal in tougher RF environments. We also made it smaller and lighter making it an even better choice for current micro brushed and brushless whoops. 

Binding Instructions:

Power on receiver
Push bind button once - (LED will blink red/blue)
Bind to Radio - Done!

Features

Ultra mini size and lightweight
Sbus signal output
Solder onboard Micro Antenna

Specifications

Dimension: 13mm*11.5mm (L*W)
Weight: 0.51g
Compatible Protocols: Flysky
Operating Voltage Range: 3~10V

Includes

BeeCeiver Flysky
Silicone Wires
Heat shrink


After creating one of the best micro receivers on the market, we went back to the lab and improved the range by almost double! By using diversity antennas (The world's smallest diversity Flysky compatible receivers)not only are you getting better range, but your getting a more reliable signal in tougher RF environments

NewBeeDrone Beeceiver Flysky Compatible Micro Receiver from WREKD Co.

NewBeeDrone Beeceiver Flysky Compatible Micro Receiver

After creating one of the best micro receivers on the market, we went back to the lab and improved the range by almost double! By using diversity antennas (The world's smallest diversity Flysky compatible receivers)not only are you getting better range, but your getting a more reliable signal in tougher RF environments. We also made it smaller and lighter making it an even better choice for current micro brushed and brushless whoops. 

Binding Instructions:

Power on receiver
Push bind button once - (LED will blink red/blue)
Bind to Radio - Done!

Features

Ultra mini size and lightweight
Sbus signal output
Solder onboard Micro Antenna

Specifications

Dimension: 13mm*11.5mm (L*W)
Weight: 0.51g
Compatible Protocols: Flysky
Operating Voltage Range: 3~10V

Includes

BeeCeiver Flysky
Silicone Wires
Heat shrink


BayckRC

BayckRC ELRS 2.4GHz Dual Diversity TCXO Receiver - T Antenna

BAYCKRC














Stay connected and in control with the BayckRC ELRS Nano Receiver. Designed with a T Antenna, this 2.4GHz receiver ensures steady and reliable signal transmission for your RC device. Experience seamless control and enjoy uninterrupted connection with this receiver.













Now the new TCXO version receiver applies a “Temperature Compensated Crystal Oscillator”, accurate frequency, and excellent performance in extreme temperature environments, making the TCXO much more reliable.


























Check out the rest of our RC receivers and all our RC transmitters, modules, and accessories, as well as all our BayckRC Products!
Features


Small size


1.6g weight

ELRS open source project, remote control

The operation is simple

Specifications

Name: ExpressLRS Receiver
RF: Freq: 2.4Ghz
IC: ESP32+2 x SX1281+TCXO
TX Power: 2x 100mW
Color: Blue
Weight: 1.6g (receiver only)
Size: 13mmx22mm
Firmware: BAYCKRC 2.4GHz Dual Core RX

Input Power: 3.6-5.5V 
Connector: 2x IPEX 1 (U.FL)

Includes

1x BayckRC ELRS 2.4GHz Dual Diversity TCXO Receiver w/ Plug - T Antenna


Stay connected and in control with the BayckRC ELRS Nano Receiver. Designed with a T Antenna, this 2.4GHz receiver ensures steady and reliable signal transmission for your RC device. Experience seamless control and enjoy uninterrupted connection with this receiver. Now the new TCXO version receiver applies a “Temperatu

BayckRC ELRS 2.4GHz Dual Diversity TCXO Receiver w/ Plug - T Antenna

BayckRC ELRS 2.4GHz Dual Diversity TCXO Receiver w/ Plug - T Antenna from WREKD Co.

BayckRC ELRS 2.4GHz TCXO Receiver - T Antenna














Stay connected and in control with the BayckRC ELRS Nano Receiver. Designed with a T Antenna, this 2.4GHz receiver ensures steady and reliable signal transmission for your RC device. Experience seamless control and enjoy uninterrupted connection with this receiver. 
Now the new TCXO version receiver applies a “Temperature Compensated Crystal Oscillator”, accurate frequency, and excellent performance in extreme temperature environments, making the TCXO much more reliable.













Check out the rest of our RC receivers and all our RC transmitters, modules, and accessories, as well as all our BayckRC Products!
Features


Small size


0.6g weight

ELRS open source project, remote control

The operation is simple

Specifications

Name: ExpressLRS Receiver
RF: Freq: 2.4Ghz
IC: SX1281+ESP8285+TCXO
TX Power: 100mW
Color: Blue
Weight: 0.6g (receiver only)
Size: 11mmx18mm
Firmware: BAYCKRC 2.4GHz Nano RX

Input Power: 3.6-5.5V 
Connector: U.FL

Includes

1x BayckRC ELRS TCXO 2.4GHz Receiver w/ Plug - T Antenna


Stay connected and in control with the BayckRC ELRS Nano Receiver. Designed with a T Antenna, this 2.4GHz receiver ensures steady and reliable signal transmission for your RC device. Experience seamless control and enjoy uninterrupted connection with this receiver.  Now the new TCXO version receiver applies a “Temperat

BayckRC ELRS 2.4GHz TCXO Receiver w/ Plug - T Antenna from WREKD Co.

BayckRC ELRS 2.4GHz TCXO Receiver w/ Plug - T Antenna

BayckRC ELRS 2.4GHz Receiver - T Antenna














Stay connected and in control with the BayckRC ELRS Nano Receiver. Designed with a T Antenna, this 2.4GHz receiver ensures steady and reliable signal transmission for your RC device. Experience seamless control and enjoy uninterrupted playtime with this receiver. 













Check out the rest of our RC receivers and all our RC transmitters, modules, and accessories! 
Features


Small size

0.4g weight

ELRS open source project, remote control

The operation is simple

Specifications

Name: ExpressLRS Receiver
RF: Freq: 2.4Ghz
Connector: U.FL
IC: SX1281+ESP8285
TX Power: 100mW
Color: Black 
Weight: 0.4g (receiver only)
Size: 11mmx18mm
Firmware: BAYCKRC 2.4GHz Nano RX


Includes

1x BayckRC ELRS 2.4GHz Receiver - T Antenna


Stay connected and in control with the BayckRC ELRS Nano Receiver. Designed with a T Antenna, this 2.4GHz receiver ensures steady and reliable signal transmission for your RC device. Experience seamless control and enjoy uninterrupted playtime with this receiver.  Check out the rest of our RC receivers and all our RC t

BayckRC ELRS 2.4GHz Receiver - T Antenna from WREKD Co.

TBS Crossfire Nano SE 900MHz Receiver - Immortal T Antenna













A crossfire receiver and slammed down into one of the smallest receivers we have ever seen for a long-range system. 


Check out the rest of out TBS Products and all our receivers!













Specifications 

Weight: 0.5g (receiver only)

Size: 11mm x 18mm

Requires: Firmware V2.25

Input Power: +3.3V to 8.4V

Includes

1x Crossfire Nano Receiver
1x Crossfire Immortal T V2 Antenna
1x Spare shrink tube
6x 30awg silicon connection wires (2 black, 2 red, 1 white, 1 yellow)
1 x pin header 1x4



A crossfire receiver and slammed down into one of the smallest receivers we have ever seen for a long-range system.  Check out the rest of out TBS Products and all our receivers! Specifications  Weight: 0.5g (receiver only) Size: 11mm x 18mm Requires: Firmware V2.25 Input Power: +3.3V to 8.4V Includes 1x Crossfire Nano

TBS Crossfire Nano SE 900MHz Receiver w/  Immortal T Antenna

TBS Crossfire Nano SE 900MHz Receiver w/ Immortal T Antenna













A crossfire receiver and slammed down into one of the smallest receivers we have ever seen for a long-range system. 

Check out all our receivers!













Specifications 

Weight: 0.5g (receiver only)

Size: 11mm x 18mm

Requires: Firmware V2.25

Input Power: +3.3V to 8.4V

Includes

1x Crossfire Nano Receiver
1x Crossfire Immortal T V2 Antenna
1x Spare shrink tube
6x 30awg silicon connection wires (2 black, 2 red, 1 white, 1 yellow)
1 x pin header 1x4



A crossfire receiver and slammed down into one of the smallest receivers we have ever seen for a long-range system.  Check out all our receivers! Specifications  Weight: 0.5g (receiver only) Size: 11mm x 18mm Requires: Firmware V2.25 Input Power: +3.3V to 8.4V Includes 1x Crossfire Nano Receiver 1x Crossfire Immortal T

TBS Crossfire Nano SE 900MHz Receiver w/  Immortal T Antenna from WREKD Co.

Flywoo

Flywoo ELRS EL24E 2.4GHz Micro Receiver w/ Ceramic Antenna

The new Flywoo TCXO 2.4G ELRS utilizes a temperature-compensated crystal oscillator to enhance the accuracy of the MCU clock frequency, thereby improving the performance and reliability of the RC link. It enables longer control distances, allowing users to operate devices within a wider range. This module boasts low latency and high refresh rates.
The TCXO EL24E features a built-in SMD antenna and is based on the ESP8285 MCU and can be upgraded via WiFi. They are also equipped with the SX1280 (or SX1281) IMLTRT RF module.
Check out the rest of our receivers, as well as the rest of our Flywoo selection!
Features

Enhances MCU clock frequency accuracy
Improves RC link performance and reliability
Enables longer control distances
Low latency and high refresh rates
EL24E: built-in SMD antenna
Based on ESP8285 MCU

Upgradeable via WiFi
Equipped with SX1280 (or SX1281) IMLTRT RF module.











Specifications

Type: ISM2.4GHz

ESP8285 MCU

SX1280(SX1281)IMLTRT RF Module

Frequency Range: 2400 MHz to 2500 MHz

Receive refresh rate: 25HZ~500Hz

Working voltage: 5V

Weight: 0.44 gram(without antenna)

Dimension: 10mmx10mmx6mm

Communication Protocol: CRSF(Betaflight)

Peak gain: 3.7dB
Default Firmware out of the factory: Flywoo EL24E 2.4GHz RX 3.0.0

Built-in a TCXO (temperature-compensated crystal oscillator)

Includes

1x Flywoo EL24E TCXO V2 ELRS 2.4GHz Micro Receiver - Ceramic Antenna
1x Silicone Cable
1x Heat shrink tubing


The new Flywoo TCXO 2.4G ELRS utilizes a temperature-compensated crystal oscillator to enhance the accuracy of the MCU clock frequency, thereby improving the performance and reliability of the RC link. It enables longer control distances, allowing users to operate devices within a wider range. This module boasts low la

Flywoo EL24E TCXO V2 ELRS 2.4GHz Micro Receiver - Ceramic Antenna from WREKD Co.

Flywoo EL24E TCXO V2 ELRS 2.4GHz Micro Receiver - Ceramic Antenna

The Flywoo 2.4GHz ELRS Nano Series Receiver is an Open Source Program Based on ExpressLRS, the Lightweight, the Lightweight, Minimal Size, Use ESP8285 MCU. So You Can Upgrade Firmware by WiFi, That's Too Simple, divided into two Version EL24E / EL24P.  It has a Built-in Ceramic Antenna, Which Is Super Light and Small i

FLYWOO

GEPRC

GEPRC ELRS 2.4GHz Dual RX Diversity Receiver













The ELRS DUAL 2.4G Diversity Receiver from GEPRC is a game-changing, dual-antenna system utilizing ExpressLRS open source tech. It offers exceptional coverage, low latency, and a fast refresh rate of 1000Hz, all at a budget-friendly price! With its optimal positioning of dual antennas, it offers far better signal reception and sturdier connection than most single-antenna setups. It uses a TCXO temperature-compensated crystal oscillator to avoid frequency shifts caused by temperature changes and the telemetry power is up to 100mW.








Check out all our receivers,  as well as the rest of our GEPRC selection.















Features

20mmx14mm Small size

1.2g weight

WIFI Upgrade firmware

ELRS open source project, remote control

Maximum refresh rate of 1000Hz

Two independent RF receiving links, true diversity receiver

The use of a temperature-compensated crystal oscillator (TXCO), no fear of high or
low-temperature impact, more stable performance, even if long hours of work is
not easy to cause loss of control

Built-in PA + LNA, up to 100mW telemetry power











Specifications

Size: 20x14mm
Weight: 1.2g (RX only)
Chips: ESP32-PICO-D4, SX1281
Crystal Oscillator: TCXO
Frequency Band: 2.4GHz ISM
Refresh Rate: 25Hz-1000Hz
Input Voltage: 5V
Antenna Connector: ipex1
Indicator Light: RGB light
TLM Power: 20dBm

Binding
The factory firmware version of ELRS DUAL 2.4G Diversity Receiver is above 3.x , 3.x and 2.x firmware are not compatible, so the TX module firmware needs to be upgraded to above 3.x before binding.

Power on and off the diversity receiver three times with 1 second between each interval continuously to enter the Binding Mode.；
RGB indicator flashes twice quickly on the diversity receiver, indicating that the receiver is now in Binding Mode.；
Configure remote control or transmitter module to bind with the receiver If the receiver RGB indicator is solid on, this indicates that the receiver has successfully bound.

Includes

1x GEPRC ELRS 2.4GHz Dual RX Diversity Receiver
2x ELRS 2.4GHz Antenna


The ELRS DUAL 2.4G Diversity Receiver from GEPRC is a game-changing, dual-antenna system utilizing ExpressLRS open source tech. It offers exceptional coverage, low latency, and a fast refresh rate of 1000Hz, all at a budget-friendly price! With its optimal positioning of dual antennas, it offers far better signal recep

GEPRC ELRS 2.4GHz Dual RX Diversity Receiver from WREKD Co.

Happymodel

HappyModel ELRS ES900 900MHz Dual RX Diversity Receiver

The Happymodel ES900 DUAL RX ELRS Diversity 915MHz Long Range Receiver is the perfect addition to any quadcopter or drone. With its advanced 915MHz radio frequency technology, it provides superior signal quality and lower latency. Enjoy a reliable, crystal-clear connection with the ES900 dual receiver. Check out our Ex

Happymodel ES900 DUAL RX ELRS Diversity 915MHz Long Range Receiver

HappyModel ES900 DUAL RX ELRS Diversity Receiver 915MHz / 868MHz Built-in TCXO for RC Airplane FPV Long Range Drones. 
Check out the rest of our ELRS accessories, and our HappyModel collection!
Specifications 

Brand: Happymodel

Type: 915MHz/868MHz true diversity receiver

ESP32 PICO D4, dual SX1276

Antenna connector: IPEX MHF 1/U.FL

RF Frequency: 915MHz or 868MHz (Optional)

Telemetry power: 17dbm

Receiver protocol: CRSF

Input voltage: +5V DC @ “5v” pad

PCB size: 21.5mm x 16mm

Weight: 1.5gram exclude antenna

Built-in a TCXO (temperature compensated crystal oscillator)

 Includes

1x HappyModel ES900 900MHz ELRS Dual RX Diversity Receiver



HappyModel ES900 DUAL RX ELRS Diversity Receiver 915MHz / 868MHz Built-in TCXO for RC Airplane FPV Long Range Drones.  Check out the rest of our ELRS accessories, and our HappyModel collection! Specifications  Brand: Happymodel Type: 915MHz/868MHz true diversity receiver ESP32 PICO D4, dual SX1276 Antenna connector: IP

HappyModel ES900 900MHz ELRS Dual RX Diversity Receiver from WREKD Co.

HappyModel ES900 900MHz ELRS Dual RX Diversity Receiver

HAPPYMODEL

Foxeer

Foxeer ELRS 900MHz Receiver

For use with 915MHz ELRS Transmitters. Not compatible with 2.4GHz ELRS.
Foxeer had dipped their toe into the ELRS game with their new receivers. This version includes T shaped antenna giving fantastic ELRS reception.
Specifications

Processor: ESP8285+SX1276
Work Frequency: 915/868MHz

Flash Frequency: 25~500Hz
Telemetry RF Power: 50mW Max
FW Version: 3.2.0

Firmware Target: Foxeer 900 RX

Bus Interface: CRSF
Indicator: Blue LED
Antenna Connector: U.fl
Input Voltage: 4-5.5V
Weight: 1g (without antenna)
Dimensions: 11x18.5mm

Includes

1x T Antenna 915/868MHz Receiver For ELRS Protocol
1x Antenna
1x Heat Shrink Tube
1x Cable
1x 4-Pin Header

Wiring Diagram



Foxeer had dipped their toe into the ELRs game with their new receivers. This version includes T shaped antenna giving fantastic ELRS reception.

T Antenna 915/868MHz Receiver For ELRS Protocol

FOXEER

Note: For use with 900MHz ELRS Transmitters. Not compatible with 2.4GHz ELRS.
The Foxeer ELRS 915Mhz/868MHz  receiver offers superior ELRS reception with its T-shaped antenna, giving you reliable and secure control over your aircraft. Enjoy worry-free communication with top of the line reception.
Check out the rest of our ELRS accessories, as well as the rest of our Foxeer Collection!
Features

50mW Telemetry RF Power
Improved RF Design
200Hz High Refresh Rate


Specifications 

Processor: ESP8285+SX1276

Work Frequency: 915MHz/868MHz

Flash Frequency: 25~200Hz

Telemetry RF Power: 50mW Max

FW Version: V3.2.0 pre-installed

FW Target: Foxeer 900 RX

Bus Interface: CRSF

Indicator: Blue LED

Antenna Connector: U.FL

Input: 4~5.5V

Weight: 1g without antenna

Size: 11x18.5mm


Includes

Foxeer ELRS 915/868MHz Receiver


Note: For use with 900MHz ELRS Transmitters. Not compatible with 2.4GHz ELRS. The Foxeer ELRS 915Mhz/868MHz  receiver offers superior ELRS reception with its T-shaped antenna, giving you reliable and secure control over your aircraft. Enjoy worry-free communication with top of the line reception. Check out the rest of 

Foxeer ELRS 900MHz Receiver from WREKD Co.

RadioMaster RP1 V2 2.4GHz ELRS Nano Receiver

The RadioMaster RP series receivers are built-in a TCXO (temperature-compensated crystal oscillator) now, which ensures reliable, stable, and accurate signal reception, allowing for superior performance in demanding environments and enhancing the flight experience. The RP1 and RP2 2.4GHz ELRS nano series receivers are 

RadioMaster RP1 V2 ELRS 2.4GHz Nano Receiver w/ UFL Antenna

The RadioMaster RP1 ExpressLRS 2.4ghz Nano Receiver w/ 65mm UFL T-Antenna is an open-source receiver based on ExpressLRS.

#html-body [data-pb-style=UX2NAEC]{display:none}#html-body [data-pb-style=QJIDK79]{justify-content:flex-start;display:flex;flex-direction:column;background-position:left top;background-size:cover;background-repeat:no-repeat;background-attachment:scro

RadioMaster RP1 ExpressLRS 2.4GHz Nano Receiver w/ 65mm UFL T-Antenna

The RP1 2.4GHz ELRS nano series receivers are open-source receivers based on the ExpressLRS receiver protocol. It features WIFI built in so you can upgrade firmware by WIFI and configure the Receiver via the built-in WebUI with your PC or mobile phone. Thanks to the low-latency and high-refresh-rate RF module, the RP1 is ideal for FPV races or Long Range. Suitable for Whoops, drones, and fixed-wing models due to the ultra-light and Nano size, these receivers can fit just about anywhere!
Specifications

Antenna: 65mm 2.4ghz T Antenna
Maximum receive refresh rate: 500Hz / F1000Hz
Minimum receiver refresh rate: 25Hz
Working voltage: 5v
Weight: 2.2g (Including antenna)
Dimension: 13x11x3mm
Firmware Version: ExpressLRS v2.4 pre-installed
FW Target: RadioMaster RP1/2 2400 RX
Bus interface: CRSF 

Includes

1x RP1 2.4GHz Receiver For ELRS Protocol

Wiring Diagram



The RP1 2.4GHz ELRS nano series receivers are open-source receivers based on the ExpressLRS receiver protocol. It features WIFI built in so you can upgrade firmware by WIFI and configure the Receiver via the built-in WebUI with your PC or mobile phone. Thanks to the low-latency and high-refresh-rate RF module, the RP1 is ideal for FPV races or Long Range. Suitable for Whoops, drones, and fixed-wing models due to the ultra-light and Nano size, these receivers can fit just about anywhere!

RP1 2.4GHz Receiver For ELRS Protocol

RadioMaster RP1 ExpressLRS 2.4ghz Nano Receiver

RadioMaster RP1 ExpressLRS 2.4ghz Nano Receiver - RMRC










Note: The packaging in this product will mention V2, however the software is confirmed ELRS V3.
The Nano receivers, developed by Jye Smith of ExpressLRS, have ESP8285 MCU and SX1280 RF chip. RP1 has a UFL antenna socket while RP2 has a built-in ceramic antenna, making it super light and small. Both have WIFI built in, allowing you to upgrade firmware and configure the Receiver via WebUI. Both RP1 and RP2 have low-latency, high-refresh-rate RF module, making them ideal for FPV and long-range. Furthermore, their ultra-light Nano size allows you to fit them anywhere, from whoops to fixed-wing models. The EP1 comes with ELRS Firmware V3 pre-installed and a TCXO oscillator for solid connection &amp reliability.









Check out the RP2 if that fits your needs more!
Check out the rest of our RC receivers and all our RC transmitters, modules, and accessories!
Features


TCXO oscillator for solid connection &amp reliability.
Improved PCB design is better for heat dissipation.
ELRS Firmware V3 (pre-installed)

LED on the top side of PCB.

Solder pads are improved and easier to solder to.
Open-source receiver based on ExpressLRS
Upgraded rigid antenna with greater durability and performance










Specifications

Item: RP1 Nano ExpressLRS 2.4ghz Receiver
Type: ISM
Antenna: 65mm 2.4ghz T Antenna
Maximum receive refresh rate: 500Hz / F1000Hz
Minimum receiver refresh rate: 25Hz
Working voltage: 5v
Weight: 2.2g (Including antenna)
Dimension: 13mmx11mmx3mm
Firmware Version: ExpressLRS v3.0 pre-installed
FW Target: RadioMaster RP1/2 2400 RX
Bus interface: CRSF

User Manual

RP1 Receiver User Manual

Includes

1x RadioMaster RP1 V2 2.4GHz ELRS Nano Receiver
1x 65mm UFL 2.4Ghz T Antenna
1x User Manual



Note: The packaging in this product will mention V2, however the software is confirmed ELRS V3. The Nano receivers, developed by Jye Smith of ExpressLRS, have ESP8285 MCU and SX1280 RF chip. RP1 has a UFL antenna socket while RP2 has a built-in ceramic antenna, making it super light and small. Both have WIFI built in, allowing you to upgrade firmware and configure the Receiver via WebUI. Both RP1 and RP2 have low-latency, high-refresh-rate RF module, making them ideal for FPV and long-range. Furthermore, their ultra-light Nano size allows you to fit them anywhere, from whoops to fixed-wing models. Check out the RP2 if that fits your needs more! Check out the rest of our RC receivers and all our RC transmitters, modules, and accessories! Features Improved PCB design is better for heat dissipation. ELRS Firmware V3 (pre-installed) LED on the top side of PCB. Solder pads are improved and easier to solder to. Open-source receiver based on ExpressLRS Upgraded rigid antenna with greater durability and performance Specifications Item: RP1 Nano ExpressLRS 2.4ghz Receiver Type: ISM Antenna: 65mm 2.4ghz T Antenna Maximum receive refresh rate: 500Hz / F1000Hz Minimum receiver refresh rate: 25Hz Working voltage: 5v Weight: 2.2g (Including antenna) Dimension: 13mmx11mmx3mm Firmware Version: ExpressLRS v3.0 pre-installed FW Target: RadioMaster RP1/2 2400 RX Bus interface: CRSF User Manual RP1 Receiver User Manual Includes 1x RadioMaster RP1 V2 2.4GHz ELRS Nano Receiver 1x 65mm UFL 2.4Ghz T Antenna 1x User Manual

RADIOMASTER










Note: The packaging in this product will mention V2, however the software is confirmed ELRS V3.
The Nano receivers, developed by Jye Smith of ExpressLRS, have ESP8285 MCU and SX1280 RF chip. RP1 has a UFL antenna socket while RP2 has a built-in ceramic antenna, making it super light and small. Both have WIFI built in, allowing you to upgrade firmware and configure the Receiver via WebUI. Both RP1 and RP2 have low-latency, high-refresh-rate RF module, making them ideal for FPV and long-range. Furthermore, their ultra-light Nano size allows you to fit them anywhere, from whoops to fixed-wing models. The EP1 comes with ELRS Firmware V3 pre-installed and a TCXO oscillator for solid connection &ampamp reliability.









Check out the RP2 if that fits your needs more!
Check out the rest of our RC receivers and all our RC transmitters, modules, and accessories!
Features


TCXO oscillator for solid connection &ampamp reliability.
Improved PCB design is better for heat dissipation.
ELRS Firmware V3 (pre-installed)

LED on the top side of PCB.

Solder pads are improved and easier to solder to.
Open-source receiver based on ExpressLRS
Upgraded rigid antenna with greater durability and performance










Specifications

Item: RP1 Nano ExpressLRS 2.4ghz Receiver
Type: ISM
Antenna: 65mm 2.4ghz T Antenna
Maximum receive refresh rate: 500Hz / F1000Hz
Minimum receiver refresh rate: 25Hz
Working voltage: 5v
Weight: 2.2g (Including antenna)
Dimension: 13mmx11mmx3mm
Firmware Version: ExpressLRS v3.0 pre-installed
FW Target: RadioMaster RP1/2 2400 RX
Bus interface: CRSF

User Manual

RP1 Receiver User Manual

Includes

1x RadioMaster RP1 V2 2.4GHz ELRS Nano Receiver
1x 65mm UFL 2.4Ghz T Antenna
1x User Manual



Note: The packaging in this product will mention V2, however the software is confirmed ELRS V3. The Nano receivers, developed by Jye Smith of ExpressLRS, have ESP8285 MCU and SX1280 RF chip. RP1 has a UFL antenna socket while RP2 has a built-in ceramic antenna, making it super light and small. Both have WIFI built in, 

RadioMaster RP1 V2 2.4GHz ELRS Nano Receiver from WREKD Co.

RadioMaster - RP1 2.4ghz ExpressLRS ELRS Nano Receiver V2

RadioMaster - RP1 2.4ghz ExpressLRS ELRS Nano Receiver V2 - RMRC

RadioMaster - RP1 2.4ghz ELRS Nano Receiver V2

RadioMaster RP2 V2 2.4GHz Nano ELRS Receiver










Note: The packaging in this product will mention V2, however the software is confirmed ELRS V3.
The RP2 has a ceramic antenna, super light &amp small, ideal for racing. Built-in WIFI lets you upgrade firmware &amp configure the receiver via WebUI on PC/mobile. Low latency &amp high refresh rate makes it perfect for FPV &amp long-range flights. Also great for whoops, drones &amp fixed-wing models, as this nano receiver can fit anywhere! Developed by Jye Smith &amp the ExpressLRS team, it uses ESP8285 MCU &amp SX1280 RF chip. The EP2 comes with ELRS Firmware V3 pre-installed and a TCXO oscillator for solid connection &amp reliability.
Check out the rest of our RC receivers and all our RC transmitters, modules, and accessories!













 

Features


TCXO oscillator for solid connection &amp reliability.
Improved PCB design is better for heat dissipation.
LED on the top side of PCB.

Solder pads are improved and easier to solder to.
Open-source receiver based on ExpressLRS
Upgraded rigid antenna with greater durability and performance

Specifications

MCU: ESP8285

Type: ISM

Antenna: On Board SMT Antenna
Bus interface: CRSF

Power input range: 5V

RF Chip: SX1280IMLTRT

Maximum receive refresh rate: 500Hz / F1000Hz
Minimum receiver refresh rate: 25Hz
Firmware Version: ExpressLRS V3.0 pre-installed

Signal format: ELRS
FW Target: RadioMaster RP2 2400 RX
Size: 13 x 11 x 7mm

Weight: 0.55g (On Board antenna)


User Manual

RP2 Receiver User Manual

Includes

1 x RadioMaster RP2 V2 2.4GHz ELRS Nano Receiver - Ceramic Antenna
1 x User Manual



Note: The packaging in this product will mention V2, however the software is confirmed ELRS V3. The RP2 has a ceramic antenna, super light &amp; small, ideal for racing. Built-in WIFI lets you upgrade firmware &amp; configure the receiver via WebUI on PC/mobile. Low latency &amp; high refresh rate makes it perfect for 

RadioMaster RP2 V2 2.4GHz ELRS Nano Receiver - Ceramic Antenna

RadioMaster RP2 2.4ghz ExpressLRS ELRS Nano Receiver V2

RadioMaster RP2 2.4ghz ExpressLRS ELRS Nano Receiver V2 - RMRC

RadioMaster RP2 2.4ghz ELRS Nano Receiver V2










Note: The packaging in this product will mention V2, however the software is confirmed ELRS V3.
The RP2 has a ceramic antenna, super light &ampamp small, ideal for racing. Built-in WIFI lets you upgrade firmware &ampamp configure the receiver via WebUI on PC/mobile. Low latency &ampamp high refresh rate makes it perfect for FPV &ampamp long-range flights. Also great for whoops, drones &ampamp fixed-wing models, as this nano receiver can fit anywhere! Developed by Jye Smith &ampamp the ExpressLRS team, it uses ESP8285 MCU &ampamp SX1280 RF chip. The EP2 comes with ELRS Firmware V3 pre-installed and a TCXO oscillator for solid connection &ampamp reliability.
Check out the rest of our RC receivers and all our RC transmitters, modules, and accessories!













 

Features


TCXO oscillator for solid connection &ampamp reliability.
Improved PCB design is better for heat dissipation.
LED on the top side of PCB.

Solder pads are improved and easier to solder to.
Open-source receiver based on ExpressLRS
Upgraded rigid antenna with greater durability and performance

Specifications

MCU: ESP8285

Type: ISM

Antenna: On Board SMT Antenna
Bus interface: CRSF

Power input range: 5V

RF Chip: SX1280IMLTRT

Maximum receive refresh rate: 500Hz / F1000Hz
Minimum receiver refresh rate: 25Hz
Firmware Version: ExpressLRS V3.0 pre-installed

Signal format: ELRS
FW Target: RadioMaster RP2 2400 RX
Size: 13 x 11 x 7mm

Weight: 0.55g (On Board antenna)


User Manual

RP2 Receiver User Manual

Includes

1 x RadioMaster RP2 V2 2.4GHz ELRS Nano Receiver - Ceramic Antenna
1 x User Manual



RadioMaster RP2 V2 2.4GHz ELRS Nano Receiver - Ceramic Antenna from WREKD Co.

BetaFPV

BetaFPV ELRS SuperD Diversity 2.4GHz Receiver

BETAFPV

BETAFPV SuperD ELRS is the first True Diversity Receiver that applies two antennas, dual receiver chains, and TCXO (temperature compensated crystal oscillator) tech, achieving a super accurate frequency rate and excellent performance in extreme temperature environments. It offers 2.4GHz and 915MHz/868MHz versions, and greatly fulfills the requirements of reliability for long-range flying, aerial photography, or FPV freestyle tricks.
A ton of ExpressLRS items are available now!
Recommend ExpressLRS Recovery Dongle for flashing or recovering the receiver.

Bullet Points

A true diversity receiver with two complete RF receiver chains (referring to dual SX1280/SX1281 or dual SX1276), based on the latest official ExprssLRS. It comes with ExpressLRS V3.0.0 firmware.
Ultralight weight is only 1.1g without the antenna. The receiver board features a reasonable layout and is impeccably clean. Very easy to solder.
Two Dipole T antennas will create an omnidirectional signal for good signal transmission. Placing the antenna separately and vertically as far apart as possible to get a better signal is recommended.
Not only it is used for FPV drones but also for FPV fixed-wing, or other FPV aircraft. It has superb performance in long-range flying.

The first true diversity receiver for the 915MHz/868MHz frequency bands, with two separate receiving modules working together to improve signal reception quality and overall reliability.
The 900MHz radio system exhibits greater diffraction ability due to its lower frequency, while the 2.4GHz systems tend to be directional and susceptible to attenuation caused by buildings, foliage, or moisture.

Specification

Item: BETAFPV SuperD ELRS 2.4GHz/915MHz/868MHz Diversity Receiver
MCU: ESP32 PICO D4, dual SX1280(SX1281) (2.4GHz) / dual SX1276 (915MHz/868MHz)
Telemetry power: 20dBm (2.4GHz) / 17dBm (915MHz/868MHz)
Weight excluding antenna: 1.1g (2.4GHz) / 1.2g (915MHz/868MHz)
RF Frequency: 2.4GHz (ISM) / 915MHz FCC/868MHz EU

Antenna connector: IPEX MHF 1/U.FL
Input voltage: +5V DC @ “+” pad
Receiver protocol: CRSF
PCB size: 22mm x 14mm

First True Diversity Receiver with TCXO
SuperD ELRS 2.4GHz Diversity Receiver is built-in a TCXO (temperature compensated crystal oscillator), which is shared by two RF chips for a super accurate clock source. The true diversity receiver including two RF chips and PA+LNA will generate a large amount of heat when working. With the high-quality TCXO, it can withstand extreme temperatures with no fear of heat and cold, continuously outputting accurate frequency for long-range flight. Click to learn more about the TCXO.

BETAFPV ExpressLRS Receivers
SuperD ELRS 2.4GHz Diversity Receiver has dual RF receiver chains with two antennas, ensuring longer and more stable flying for FPV drones and RC airplanes. Choosing a suitable receiver to fly quadcopter or other RC models is very important. BETAFPV ExpressLRS Receivers including ELRS Lite, Nano, Micro, and the newest SuperD, greatly fulfill pilots' requirements for FPV flying.




SuperD RX
Micro RX
Nano RX
Lite RX


Weight

1.1g (2.4GHz), 1.2g (915/868MHz)

3.5g (RX only)
0.7g (RX only)
0.47g (Tower), 0.53g (Flat)



Antenna
IPEX MHF1 + T antenna
IPEX MHF1 + T antenna
IPEX MHF1 + T antenna
SMD ceramic antenna



MCU
ESP32-PICO-D4
ESP8285

ESP8285

ESP8285 



RF Chip

Dual SX128X + Dual PA (2.4GHz), Dual SX1276 (915/868MHz)

SX128X
SX128X + PA, SX1276 + PA
SX128X


Frequency
2.4GHz ISM, 915MHz (FCC), 868MHz (EU)
2.4GHz ISM
2.4GHz ISM, 915MHz (FCC), 868MHz (EU)

2.4GHz ISM



Telemetry Power
100mW
17mW
100mW
17mW


Serial Output Protocol
CRSF
PWM or CRSF
CRSF
CRSF


Model Type
FPV Drone, Fixed-wing aircraft
Fixed-wing aircraft, Helicopter, RC Cars, RC Boats
FPV Drone
Whoop Drone





Diagram
The SuperD receiver 2.4GHz version diagram is shown below.

The SuperD receiver 915MHz/868MHz version diagram is shown below.

SuperD receiver RGB status indication is shown below.



RGB Color
Status
Description


Rainbow
Fade effect
Power on


Green
Slow flash
WIFI upgrading mode


Red
Quick flash
No RF chip detected


Orange
Double flash
Binding mode


Orange
Triple flash
Connected, but mismatched model-match configuration



Orange
Slow flash
Waiting for connection



Solid on
Connected and color indicates packet rate



The RGB light color corresponding to the packet rate is shown in the figure below.
2.4GHz:

Note: F1000 and F500 are packet rates in FLRC mode, providing faster modulation and lower latency, but at the same time having shorter reception distance than normal Lora mode. This mode is great for racers.
D500 and D250 are packet rates in DVDA (Deja Vu Diversity Aid) mode. This mode works at the F1000 data packet rate of FLRC mode, providing better link connection in the case of complex interference by sending the same data packet multiple times. D500 and D250 indicate that the same data packet is sent twice and four times respectively.
915MHz/868MHz:

Note: D50 is a unique mode of ELRS Team900. Under the 200Hz refresh rate of Lora mode, the same data packet is repeatedly sent four times, and the receiving distance is equivalent to 200Hz.
100Hz Full is a mode that realizes 16-channel full-resolution output at the 200Hz refresh rate of Lora mode, and the receiving distance is equivalent to 200Hz.
Configuration &amp Bind
ExpressLRS uses the Crossfire serial protocol (AKA CRSF protocol) to communicate between the SuperD diversity receiver and the flight controller board. Take the flight controller using the Betaflight firmware as an example to introduce its wiring and port configuration. 
The connection between the SuperD diversity receiver and the flight controller is shown in the figure below

Connect the flight controller to the Betaflight Configurator for basic configuration. First, on the "Port" page, enable the flight controller serial port (take UART1 as an example) as "Serial Rx". 

On the configuration page, set Receiver Mode to Serial (via UART) and Serial Receiver Provider to CRSF.

The default firmware of the SuperD diversity receiver uses the ExpressLRS V3.0.0 protocol and has no preset binding phrase.  Therefore, the firmware version of the transmitter module must be ExpressLRS V3.0.0 or later versions. Both the receiver and transmitter module should not have any binding phrase.

Power on and off the receiver 3 times, each step pausing 2 seconds to enter binding mode
When the indicator starts fast blink with orange twice, the receiving is at binding mode
Enter the radio or transmitter module's binding mode to bind with the receiver if the Indicator has turned solid, it indicates that the device has been bound successfully.

Note: After binding once, the receiver will remember the autosaved binding phrase and device. Further restarting of the device will be bound automatically without the need for a rebinding process.
The 2.4GHz default firmware is ELRS V3.0.0. If you would like to bind with a remote control or transmitter module, please upgrade it to V3.0.0 or above. If you would like to flash the latest official ELRS firmware for the SuperD receiver, please upgrade ELRS Configurator to V1.5.2 or above. Select the target device "BETAFPV SuperD 2.4GHz RX". 

The 915MHz/868MHz default firmware is ELRS V3.3.0. The official version has not yet been released. It will be updated synchronously with the ELRS V3.3 version. Then you can click the latest ELRS Configurator Nightly to operate. Select the target device ''BETAFPV SuperD 900MHz RX''.
Note: Firmware for 915MHz/868MHz is currently self-compiled firmware.

FAQ

BETAFPV SuperD ELRS 2.4GHz Diversity Receiver user manual for download.
Download the Firmware for SuperD ELRS 2.4GHz/915MHz/868MHz Diversity Receiver.
How to flash the firmware via Passthrough or WIFI for SuperD Receiver.
Download TPU holders 3D-printing STL file for SuperD ELRS 2.4GHz Diversity RX.

Know More About ExpressLRS
ExpressLRS is an open-source RC link for RC applications. Everyone could find this project on Github or join the discussion in Facebook Group.

Package

1* SuperD 2.4GHz Diversity Receiver
2* 2.4GHz T Antenna
1* 4-Pin Header
1* 4-Pin Wire Harness
1* Instruction Manual
2* Heat Shrink Tubing



1* SuperD 915MHz/868MHz Diversity Receiver
2* 915MHz/868MHz T Antenna
1* 4-Pin Header
1* 4-Pin Wire Harness
1* Instruction Manual
2* Heat Shrink Tubing



BETAFPV SuperD ELRS is the first True Diversity Receiver that applies two antennas, dual receiver chains, and TCXO (temperature compensated crystal oscillator) tech, achieving a super accurate frequency rate and excellent performance in extreme temperature environments. It offers 2.4GHz and 915MHz/868MHz versions, and 

SuperD ELRS Diversity Receiver

BETAFPV SuperD ELRS 2.4G is the world&#39s first True Diversity Receiver that applies two antennas, dual receiver chains, and TCXO (temperature compensated crystal oscillator) tech, achieving super accurate frequency rate and excellent performance in extreme temperature environments. It greatly fulfills the requirements of reliability for long range flying, aerial photography, or FPV freestyle tricks
Check out all our receivers, and our entire BetaFPV selection!

Specifications

Item: BETAFPV SuperD ELRS 2.4G Diversity Receiver
MCU: ESP32 PICO D4, dual SX1280 (SX1281)
Antenna Connector: IPEX MHF 1/U.FL
RF Frequency: 2.4GHz (2400~2480MHz)
Telemetry Power: 20dBm (100mW)
Receiver Protocol: CRSF
Input Voltage: +5V DC @ “+” pad
PCB Size: 22mm*14mm
Weight: 1.1g excluding antenna


Includes

1x SuperD ELRS 2.4G Diversity Receiver
2x BETAFPV Dipole T Antenna
1x Pin Header
1x 30AWG Silicon Wires (1 black, 1 red, 1 white, 1 yellow)
1x User Manual


BETAFPV SuperD ELRS 2.4G is the world's first True Diversity Receiver that applies two antennas, dual receiver chains, and TCXO (temperature compensated crystal oscillator) tech, achieving super accurate frequency rate and excellent performance in extreme temperature environments. It greatly fulfills the requirements o

BetaFPV SuperD ELRS Diversity 2.4GHz Receiver from WREKD Co.

BetaFPV SuperD ELRS Diversity 2.4GHz Receiver

BETAFPV SuperD ELRS 2.4G is the world's first True Diversity Receiver that applies two antennas, dual receiver chains, and TCXO (temperature compensated crystal oscillator) tech, achieving super accurate frequency rate and excellent performance in extreme temperature environments. It greatly fulfills the requirements of reliability for long range flying, aerial photography, or FPV freestyle tricks
Check out all our receivers, and our entire BetaFPV selection!

Specifications

Item: BETAFPV SuperD ELRS 2.4G Diversity Receiver
MCU: ESP32 PICO D4, dual SX1280 (SX1281)
Antenna Connector: IPEX MHF 1/U.FL
RF Frequency: 2.4GHz (2400~2480MHz)
Telemetry Power: 20dBm (100mW)
Receiver Protocol: CRSF
Input Voltage: +5V DC @ “+” pad
PCB Size: 22mm*14mm
Weight: 1.1g excluding antenna


Includes

1x SuperD ELRS 2.4G Diversity Receiver
2x BETAFPV Dipole T Antenna
1x Pin Header
1x 30AWG Silicon Wires (1 black, 1 red, 1 white, 1 yellow)
1x User Manual


Happymodel ELRS EP1 TCXO 2.4GHz Receiver

The Happymodel EP1 TCXO RX is a nano-sized true diversity 2.4GHz ELRS receiver with RF amps that comes with a IPEX connector for a dipole antenna.

#html-body [data-pb-style=U8AL89K]{justify-content:flex-start;display:flex;flex-direction:column;background-position:left top;background-size:cover;background-repeat:no-repeat;background-attachment:scroll}#html-body [data-pb-style=PTNE7PN]{display:no

Happymodel TCXO ExpressLRS 2.4GHz Nano Receiver - EP1

EP1 ELRS receiver is the hottest ExpressLRS receiver since it was released. Now the new TCXO version EP series receiver apply “temperature compensated crystal oscillator”, accurate frequency and excellent performance in extreme temperature environments make these TCXO much reliable.

Check out our ExpressLRS Collection, all our Receivers and the rest of our Happymodel Products!
Specifications:

 	Type: ISM2.4GHz
 	ESP8285 MCU
 	SX1280(SX1281)IMLTRT RF Module
 	Omni directional antenna
 	Frequency Range: 2400 MHz to 2500 MHz
 	Receive refresh rate: 25HZ~500Hz
 	Working voltage: 5v
 	Weight: 0.41 gram(without antenna)
 	Dimension: 10mm*10mm*6mm
 	Peak gain: 2.23dB
 	Default Firmware out of factory: HappyModel_EP_2400_RX V2.2 version
 	Built-in a TCXO (temperature compensated crystal oscillator)

Package Includes:

 	1 x Happymodel 2.4G ExpressLRS EP1 TCXO RX Receiver Module

Happymodel 2.4G ExpressLRS EP1 TCXO RX Receiver Module | Five33

Happymodel 2.4G ExpressLRS EP1 TCXO RX Receiver Module

EP1 ELRS receiver is the hottest ExpressLRS receiver since it was released. Now the new TCXO version EP series receiver apply “temperature compensated crystal oscillator”, accurate frequency and excellent performance in extreme temperature environments make these TCXO much reliable. Check out our ExpressLRS Collection,

EP1 ELRS receiver is the hottest ExpressLRS receiver since it was released. Now the new TCXO version EP series receiver applies a “temperature compensated crystal oscillator”, accurate frequency and excellent performance in extreme temperature environments making these TCXO much more reliable.
Check out our other great receivers, and the rest of our Happymodel offerings.
Specifications


Type: ISM2.4GHz


SX1280(SX1281)IMLTRT RF Module


Antenna connector: IPEX MHF 1/U.FL


RF Frequency: 2.4GHz (2400~2480MHz)


Telemetry power: &ampgt19dbm


Receiver protocol: CRSF


Input voltage: +5V DC @ “+” pad


PCB size: 10mm x 10mm


Weight: .04 grams excluding antenna

Built-in a TCXO (temperature-compensated crystal oscillator)


Includes

1x HappyModel 2.4GHz EP1 TCXO RX Express LRS Receiver
2x Antennas


EP1 ELRS receiver is the hottest ExpressLRS receiver since it was released. Now the new TCXO version EP series receiver applies a “temperature compensated crystal oscillator”, accurate frequency and excellent performance in extreme temperature environments making these TCXO much more reliable. Check out our other great

HappyModel 2.4GHz EP1 TCXO RX ELRS Receiver from WREKD Co.

HappyModel 2.4GHz EP1 TCXO RX ELRS Receiver

EP1 ELRS receiver is the hottest ExpressLRS receiver since it was released. Now the new TCXO version EP series receiver applies a “temperature compensated crystal oscillator”, accurate frequency and excellent performance in extreme temperature environments making these TCXO much more reliable.
Check out our other great receivers, and the rest of our Happymodel offerings.
Specifications


Type: ISM2.4GHz


SX1280(SX1281)IMLTRT RF Module


Antenna connector: IPEX MHF 1/U.FL


RF Frequency: 2.4GHz (2400~2480MHz)


Telemetry power: &gt19dbm


Receiver protocol: CRSF


Input voltage: +5V DC @ “+” pad


PCB size: 10mm x 10mm


Weight: .04 grams excluding antenna

Built-in a TCXO (temperature-compensated crystal oscillator)


Includes

1x HappyModel 2.4GHz EP1 TCXO RX Express LRS Receiver
2x Antennas


Happymodel ELRS EP2 TCXO 2.4GHz Receiver

The Happymodel EP2 TCXO RX is a nano-sized true diversity 2.4GHz ELRS receiver with RF amps. This TCXO Rx receiver uses a temperature-compensated crystal oscillator to help with accurate MCU clock frequency, thus improving the performance and reliability of your RC link. Despite the small size, the low latency and high refresh rate of the ELRS system allow this receiver to be used on full-size/long-range quads, while also being small enough to be used on whoop-size quads! The Happymodel EP1 RX includes an IPEX connector for a dipole antenna, while the EP2 RX includes a built-in SMD antenna.
The EP1, EP2, and EP1 Dual modules are based on the ESP8285 MCU that allows for upgrading via WiFi, along with the SX1280(SX1281)IMLTRT RF Module.
Check out our other great receivers, and the rest of our Happymodel offerings.

Specifications


Type: ISM2.4GHz 

ESP8285 MCU
SX1280(SX1281)IMLTRT RF Module

Antenna connector: SMD Ceramic antenna

RF Frequency: 2.4GHz (2400~2480MHz)


Telemetry power: &ampgt19dbm


Receiver protocol: CRSF


Input voltage: +5V DC @ “+” pad


PCB size: 10mm x 10mm


Weight: 1gram exclude antenna

Built-in a TCXO (temperature-compensated crystal oscillator)

Firmware


Default Firmware out of the factory: HappyModel_EP_2400_RX V2.2 version
Built-in a TCXO (temperature-compensated crystal oscillator)

Includes

HappyModel 2.4GHz EP2 TCXO RX Express LRS Receiver


The Happymodel EP2 TCXO RX is a nano-sized true diversity 2.4GHz ELRS receiver with RF amps. This TCXO Rx receiver uses a temperature-compensated crystal oscillator to help with accurate MCU clock frequency, thus improving the performance and reliability of your RC link. Despite the small size, the low latency and high

HappyModel 2.4GHz EP2 TCXO RX Express LRS Receiver - Ceramic Antenna from WREKD Co.

HappyModel 2.4GHz EP2 TCXO RX Express LRS Receiver - Ceramic Antenna

EP2 ELRS receiver is the hottest ExpressLRS receiver since it was released. Now the new TCXO version EP series receiver apply “temperature compensated crystal oscillator”, accurate frequency and excellent performance in extreme temperature environments make these TCXO much reliable. Check out our ExpressLRS Collection,

Happymodel 2.4G ExpressLRS EP2 TCXO RX Receiver Module

The Happymodel EP2 TCXO RX is a nano-sized true diversity 2.4GHz ELRS receiver with RF amps. This TCXO Rx receiver uses a temperature-compensated crystal oscillator to help with accurate MCU clock frequency, thus improving the performance and reliability of your RC link. Despite the small size, the low latency and high refresh rate of the ELRS system allow this receiver to be used on full-size/long-range quads, while also being small enough to be used on whoop-size quads! The Happymodel EP1 RX includes an IPEX connector for a dipole antenna, while the EP2 RX includes a built-in SMD antenna.
The EP1, EP2, and EP1 Dual modules are based on the ESP8285 MCU that allows for upgrading via WiFi, along with the SX1280(SX1281)IMLTRT RF Module.
Check out our other great receivers, and the rest of our Happymodel offerings.

Specifications


Type: ISM2.4GHz 

ESP8285 MCU
SX1280(SX1281)IMLTRT RF Module

Antenna connector: SMD Ceramic antenna

RF Frequency: 2.4GHz (2400~2480MHz)


Telemetry power: &gt19dbm


Receiver protocol: CRSF


Input voltage: +5V DC @ “+” pad


PCB size: 10mm x 10mm


Weight: 1gram exclude antenna

Built-in a TCXO (temperature-compensated crystal oscillator)

Firmware


Default Firmware out of the factory: HappyModel_EP_2400_RX V2.2 version
Built-in a TCXO (temperature-compensated crystal oscillator)

Includes

HappyModel 2.4GHz EP2 TCXO RX Express LRS Receiver


EP2 ELRS receiver is the hottest ExpressLRS receiver since it was released. Now the new TCXO version EP series receiver apply “temperature compensated crystal oscillator”, accurate frequency and excellent performance in extreme temperature environments make these TCXO much reliable.

&ampnbsp
Specifications:

 	Type: ISM2.4GHz
 	ESP8285 MCU
 	SX1280(SX1281)IMLTRT RF Module
 	SMD Ceramic antenna
 	Frequency Range: 2400 MHz to 2500 MHz
 	Receive refresh rate: 25HZ~500Hz
 	Working voltage: 5v
 	Weight: 0.44 gram
 	Dimension: 10mm*10mm*6mm
 	Peak gain: 3.7dB
 	Default Firmware out of factory: HappyModel_EP_2400_RX V2.2 version
 	Built-in a TCXO (temperature compensated crystal oscillator)

Package Includes:

 	1 x Happymodel 2.4G ExpressLRS EP2 TCXO RX Receiver Module

Happymodel 2.4G ExpressLRS EP2 TCXO RX Receiver Module | Five33

The Happymodel EP2 TCXO RX is a nano-sized true diversity 2.4GHz ELRS receiver with RF amps and comes with a built-in SMD antenna.

#html-body [data-pb-style=RM2X10X]{justify-content:flex-start;display:flex;flex-direction:column;background-position:left top;background-size:cover;background-repeat:no-repeat;background-attachment:scroll}#html-body [data-pb-style=BOJW1X5]{display:no