FPV Quad Parts

Peripherals and Replacement Parts

Equipment

Equipment Peripherals

Build Page Parts

Build Parts Equipment

Pre-Built Quads and Kits 

Build Page Parts Overflow

Build Parts Equipment Overflow

Compatibility Categories

Continuous Amp Rating

Axis Flying

AxisFlying ECO F405 4-6S 30x30 Flight Controller Stack - F405 FC, 60A 32Bit ESC

AXIS FLYING

Argus is axisflying electronic series that include ESC, FC and stack. The lightweight Argus ECO will reduce the weight of the whole FPV to a greater extent, while providing stable and excellent control.
Check out all our 30x30 FC Stacks, and all our Axis Flying Products!
Features

The Argus ECO is significantly lighter than the Argus Pro with its aluminum housing.
The FC supports up to 4 motor outputs, easily build your drone.
Quickly check the working status of the FC by turning on and off the corresponding status indicator light.
Open circuit board, free soldering equipment.


Specifications
ECO F405 Flight Controller

Firmware: SPDX-SPEDIXF405(Betaflight)
MCU: STM43F405RGT6
GYRO: ICM42688P
BEC: 5V3A / 12V2A
UART: 6
OSD: Supported
Black box: 16M
Barometer: Not Supported
Input voltage: 4-6S
Size: 36x36x6mm
Mounting holes: 30.5x30.5mm﻿
Weight: 7g

32Bit 60A 4in1 ESC

Firmware name: Bluejay_QH30 (default)
Amperage Meter: 200
Input voltage: 4-6S
Continuous current: 60A
Burst current: 70A
Temperature protection: Supported
Telemetry: Not supported
BEC: Not supported
Size: 44.8x43.6mm
Mounting holes: 30.5x30.5mm
Weight: 13.5g

Includes

1x Axis Flying ECO F405 4-6S 30x30 Stack/Combo (F405 FC / 32Bit 60A 4in1 ESC)


Argus is axisflying electronic series that include ESC, FC and stack. The lightweight Argus ECO will reduce the weight of the whole FPV to a greater extent, while providing stable and excellent control. Check out all our 30x30 FC Stacks, and all our Axis Flying Products! Features The Argus ECO is significantly lighter 

AxisFlying ECO F405 4-6S 30x30 Stack/Combo (F405 FC / 32Bit 60A 4in1 ESC)

AxisFlying ECO F405 4-6S 30x30 Stack/Combo (F405 FC / 32Bit 60A 4in1 E

Processor (MCU)

The FC is the brain or the CPU of your quad. It has a processor and other components that allow it to listen to your inputs and tells the quad what to do. FCs are commonly sold together with other components integrated or stacked (like ESCs and video transmitters). For beginners, choose a FC with a F4 or F7 processor that has a compatible mount with your frame. 

Flight Controllers

FC Stack Mount

Built-in VTX

Built-in ESC

iFlight

iFlight Blitz F7 V1.2 2-6S 30x30 Flight Controller Stack - F7 FC, E55 32Bit 55A ESC

IFLIGHT

The V1.2 of the iFlight Blitz F7 E55 2-6S 30x30 Stack/Combo has arrived. These new flight controllers are equipped with a plug and play connectors making connecting your video transmitter, radio receiver, and other periphery sensors a breeze.
They also make diagnosing issues in the field much easier with status indicator LED's that let you know in seconds if you are having a problem with the 3.3V, 5V, or VBat. Coupled with iFlight's new 55 Amp BLHeli_32 Blitz 4-in-1 ESC, this stack can handle even the most amp hungry motors.
Check out our other 30x30 Stacks &amp Combos as well as our entire iFlight selection!
Features

Improved circuit design, better components and lower electrical noise!
DJI HD VTX Connector (Plug-and-Play / No soldering required)
FC indicator LEDs for visual debugging
With LC filter

Specification
Jan. 12, 2024: Gyroscope changed from BMI270 to ICM42688. Product name updated to BLITZ F7 V1.2 Flight Controller.
Blitz F7 V1.2

MCU: STM32 F722
Gyro: ICM42688
Barometer: DPS310
OSD Chip: AT7456E
Flash: 32MB (Blackbox flash)
UARTS: 6
Motor outputs: 4x (SH1.0 connector)
I2C serial: SDA / SLA pads
Smartaudio / IRC Tramp VTX protocol supported
LED controller: Yes
Beeper pad: Yes
Firmware target: IFRC-IFLIGHT_BLITZ_F722
Mount pattern: 30.5x30.5mm / 4mm PCB hole diameter
Dimensions: 36.5x35 mm
Weight: 7.8g
BEC: 5V 2.5A / 9V 2A

E55 4in1 ESC

Input Voltage: 2-6S

Max. Continuous Current: 55A
Max. Burst Current: 65A 
MCU: G071
BEC: No
Firmware: BLHeli32
Current Sensor: Yes
Target: IFLIGHT_BLITZ_G2
Mounting Dimensions: 30.5x30.5mm/Φ4mm
Dimensions: 35x42mm
Weight: 15.3g

Includes

1x iFlight Blitz F7 V1.2 2-6S 30x30 Stack/Combo (F7 FC/ E55 32Bit 55A 4in1 ESC)
1x XT60 Pigtail


The V1.2 of the iFlight Blitz F7 E55 2-6S 30x30 Stack/Combo has arrived. These new flight controllers are equipped with a plug and play connectors making connecting your video transmitter, radio receiver, and other periphery sensors a breeze. They also make diagnosing issues in the field much easier with status indicat

iFlight Blitz F7 V1.2 2-6S 30x30 Stack/Combo (F7 FC/ E55 32Bit 55A 4in1 ESC)

iFlight Blitz F7 V1.2 2-6S 30x30 Stack/Combo (F7 FC/ E55 32Bit 55A 4in

NewBeeDrone

NewBeeDrone X FETTec Infinity AIO G4 3-6S 30x30 Flight Controller - 45A 4in1 ESC


NewBeeDrone X FETTec InfinityAIO G4 Flight Controller MPU6000 45A 3-6S
The InfinityAIO Fettec G4 flight controller is a robust, high-performance solution that ensures reliability and protection for your drone, enabling you to fly with confidence in any environment, being the first to offer a dust and moisture-proof design with a built-in FETtec system. This 30.5x30.5 sized All-In-One (AIO) controller is a marvel of engineering, employing a unique infinityAIO design concept with two CNC aluminum heatsinks that encapsulate all electronic components. This innovative design not only ensures effective heat dissipation but also seals the sensitive electronics from environmental hazards such as dust, raindrops, and organic matter like plant juices that can cause short-circuiting and damage.
Engineered for heavy-duty performance, the InfinityAIO Fettec G4 is tailored to excel in diverse flying conditions, whether for racing, freestyle, or cinematic drone applications. It boasts an STM32G474 microcontroller unit (MCU) for rapid processing, along with an MPU6000 gyro for stable flight dynamics. The flight controller includes a 6-pin DJI FPV Air Unit connector, Micro USB connector, multiple UART ports for versatile connectivity.
The ESCs are powered by four SMT32G071 MCUs running FETTec ESC Firmware. 1.0-241 capable of handling a continuous current of 45A and bursts of up to 55A. The Dshot 300-2400 protocol is supported, ensuring high-resolution control over the motor speeds. With a power input range of 3-6S and a 12V 2A design specifically for the DJI O3 FPV Air Unit, this flight controller is built to cater to the needs of advanced FPV systems. Its compact dimensions, precise 30.5x30.5 mounting holes, and a lightweight build of 19.4 grams with grommets make it a versatile choice for various drone builds.
Additional features like the FETTEC OSD support for analog builds, buzzer readiness, and 4xLED outputs for visibility and customization highlight its user-centric design. Moreover, the provision of a 5V 3A power supply for external LED or GPS modules expands its utility for different flight scenarios.
Specification:
Microcontroller Unit (MCU) Specifications:

MCU: STM32G474 Running FETTec Alpha Firmware 0.7-62
Gyro: MPU6000
4x STM32G071 @64MHz FETtec ESC MCU Running FETTec ESC Firmware 1.0-241

Connectivity:

6-Pin DJI FPV Air Unit Connector
Micro USB Connector
UART1: DJI Connector
UART2: Used for Receiver
UART3: Free (also connect to Fettec Analog Onboard OSD)
UART4: Free
UART5: Used for ESCs / TLM / Onewire
OneWire BUS with up to 8kHz looptime (one cable for all Motor signals and Telemetry)

Power Specifications:

Continuous Current 45A and 55A Burst ESC
Dshot 300-2400
3-6S Battery Input
12V 2A Design for DJI FPV Air Unit
5V 3A Power supply for external LED or GPS module

Physical Characteristics:

Dimensions: 41x37x7.6mm with 30.5x30.5mm Mounting Holes
Weight: 19.4gr with grommets, 18.8gr without grommets

Additional Features:

FETTEC OSD support for Analog build
Buzzer Ready
4x LED

Package Contents:

1x Infinity FETtec AIO Flight Controller + ESC
1x DJI O3 Cable 100mm (Silicon wire)
2x 16Pin Cable 150mm (Teflon wire)
13x Nylon Lock Nut
5x Steel Screw M3x14
4x Grommets Short, 4x Grommets Long
1x 470uf 35v Electrolytic Capacitor
1x XT60 Cable

Note For Analog Build:
Analog build will need to setup Serial 3 to talk to the internal Analog OSD Chips.Please follow the setting below to enable the Analog OSD chips. Settings&ampgtFC Setup&ampgtSerial MSP Port1   - Serial3 
Video:
 
Wire Diagram: 


NewBeeDrone X FETTec InfinityAIO G4 Flight Controller MPU6000 45A 3-6S The InfinityAIO Fettec G4 flight controller is a robust, high-performance solution that ensures reliability and protection for your drone, enabling you to fly with confidence in any environment, being the first to offer a dust and moisture-proof des

NewBeeDrone X FETTec InfinityAIO G4 Flight Controller MPU6000 45A 3-6S from WREKD Co.

NewBeeDrone X FETTec InfinityAIO G4 Flight Controller MPU6000 45A 3-6S


NewBeeDrone X FETTec InfinityAIO G4 Flight Controller MPU6000 45A 3-6S
The InfinityAIO Fettec G4 flight controller is a robust, high-performance solution that ensures reliability and protection for your drone, enabling you to fly with confidence in any environment, being the first to offer a dust and moisture-proof design with a built-in FETtec system. This 30.5x30.5 sized All-In-One (AIO) controller is a marvel of engineering, employing a unique infinityAIO design concept with two CNC aluminum heatsinks that encapsulate all electronic components. This innovative design not only ensures effective heat dissipation but also seals the sensitive electronics from environmental hazards such as dust, raindrops, and organic matter like plant juices that can cause short-circuiting and damage.
Engineered for heavy-duty performance, the InfinityAIO Fettec G4 is tailored to excel in diverse flying conditions, whether for racing, freestyle, or cinematic drone applications. It boasts an STM32G474 microcontroller unit (MCU) for rapid processing, along with an MPU6000 gyro for stable flight dynamics. The flight controller includes a 6-pin DJI FPV Air Unit connector, Micro USB connector, multiple UART ports for versatile connectivity.
The ESCs are powered by four SMT32G071 MCUs running FETTec ESC Firmware. 1.0-241 capable of handling a continuous current of 45A and bursts of up to 55A. The Dshot 300-2400 protocol is supported, ensuring high-resolution control over the motor speeds. With a power input range of 3-6S and a 12V 2A design specifically for the DJI O3 FPV Air Unit, this flight controller is built to cater to the needs of advanced FPV systems. Its compact dimensions, precise 30.5x30.5 mounting holes, and a lightweight build of 19.4 grams with grommets make it a versatile choice for various drone builds.
Additional features like the FETTEC OSD support for analog builds, buzzer readiness, and 4xLED outputs for visibility and customization highlight its user-centric design. Moreover, the provision of a 5V 3A power supply for external LED or GPS modules expands its utility for different flight scenarios.
Specification:
Microcontroller Unit (MCU) Specifications:

MCU: STM32G474 Running FETTec Alpha Firmware 0.7-62
Gyro: MPU6000
4x STM32G071 @64MHz FETtec ESC MCU Running FETTec ESC Firmware 1.0-241

Connectivity:

6-Pin DJI FPV Air Unit Connector
Micro USB Connector
UART1: DJI Connector
UART2: Used for Receiver
UART3: Free (also connect to Fettec Analog Onboard OSD)
UART4: Free
UART5: Used for ESCs / TLM / Onewire
OneWire BUS with up to 8kHz looptime (one cable for all Motor signals and Telemetry)

Power Specifications:

Continuous Current 45A and 55A Burst ESC
Dshot 300-2400
3-6S Battery Input
12V 2A Design for DJI FPV Air Unit
5V 3A Power supply for external LED or GPS module

Physical Characteristics:

Dimensions: 41x37x7.6mm with 30.5x30.5mm Mounting Holes
Weight: 19.4gr with grommets, 18.8gr without grommets

Additional Features:

FETTEC OSD support for Analog build
Buzzer Ready
4x LED

Package Contents:

1x Infinity FETtec AIO Flight Controller + ESC
1x DJI O3 Cable 100mm (Silicon wire)
2x 16Pin Cable 150mm (Teflon wire)
13x Nylon Lock Nut
5x Steel Screw M3x14
4x Grommets Short, 4x Grommets Long
1x 470uf 35v Electrolytic Capacitor
1x XT60 Cable

Note For Analog Build:
Analog build will need to setup Serial 3 to talk to the internal Analog OSD Chips.Please follow the setting below to enable the Analog OSD chips. Settings&gtFC Setup&gtSerial MSP Port1   - Serial3 
Video:
 
Wire Diagram: 


NewBeeDrone X FETTec Infinity AIO G4 3-6S 30x30 Flight Controller (w/ 45A 4in1 ESC) - MPU6000

NewBeeDrone X FETTec Infinity AIO G4 3-6S 30x30 Flight Controller (w/ 

HAKRC

HAKRC F4126 20A Whoop AIO Flight Controller

The F4126 is HakRC's new whoop style flight controller/ESC AIO board for ultralight and whoop build. This FC features a Barometer which is rare to see in this type of flight controller and can handle up to 4S power.Checkout all our Whoop Style Flight Controllers and the rest of our HAKRC products! Features: 1.PCB adopt

HAKRC  F4126 BLHELI_S 20A WHOOP AIO FC

The F4126 is HakRC's new whoop style flight controller/ESC AIO board for ultralight and whoop build. This FC features a Barometer which is rare to see in this type of flight controller and can handle up to 5S power.
Check out the rest of our 20x20 ESCs, as well as HAKRC products!
Features

The PCB uses high-end 8 layers of 2oZ thick copper, which has stronger over current capability and good heat dissipation.
MOS adopts imported 30V high current resistance MOS, long life and strong load capacity.
Using industrial grade LDO, high temperature resistance.
Using high-quality Japanese Murata capacitors, strong filtering performance





Specifications

Brand: HAKRC
Item Name: HAKRC F411 20A AIO
Mounting Hole: 25.5x25.5mm/26.5x26.5mm
Weight: 8.5g
Package weight: 50g
Size: 31x31mm

Flight Controller:

CPU: STM32F411CEU6
IMU: ICM42688
OSD: AT7456E
Barometer: SPL06
LED: Supports programmable such as WS2812
Current meter: Yes
Firmware: HAKRC F411D
Support receiver: Frsky/ Futabas/ Flysky/ TBS Crossfire/ DSMX:DSM2

ESC:

Firmware: BLHELI_ S (G- H-20)
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150，Dshot300，Dshot600
Input: 2S-5S Lipo
Con. Current: 20A
Peak Current: 25A

Includes

1xHakRC F411 2-5S (F4126) AIO FC w/ 20A 8Bit 4in1 ESC
4x M2 Shock absorber
1x XT30 power cord
1x Small bandage
1x Type-C USB
1x USB cable
1x 270uf/35V capacitor
1x DJI FPV Cable
1x DJI O3 Air Unit 3-in-1 Cable
1x Instructions

Wiring


The F4126 is HakRC's new whoop style flight controller/ESC AIO board for ultralight and whoop build. This FC features a Barometer which is rare to see in this type of flight controller and can handle up to 5S power. Check out the rest of our 20x20 ESCs, as well as HAKRC products! Features The PCB uses high-end 8 layers

HakRC F4126 F411 2-5S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bit 4in1 ESC)

HakRC F4126 F411 2-5S AIO Whoop/Toothpick Flight Controller (w/ 20A 8B

BetaFPV

BetaFPV F411 V5 20A Toothpick AIO Flight Controller - F4 FC, 20A ESC

BETAFPV

As a continuance of the F411 chip, the V5 FC board is upgraded from the F4 20A V3 FC board. F411 4S 20A Toothpick Brushless Flight Controller V5 adopts BMI270 gyro instead of MPU6000 on V3 board. With two integrated plug &amp play ports for receiver and HD digital VTX, it is easy to install and requires less solder work. Besides, the board is a solid value for durable use thanks to the high-quality PCB material and enhanced production process.
Check out all our whoop flight controllers, and all our BetaFPV gear!
Features

With a large pad to solder, it is easy to solder external electronics. In addition, the V5 board features plug&ampplay ports for the receiver and HD digital VTX, which requires less solder work for convenient installation.
High-quality MOSFETs are applied to F411 4S 20A FC V5 to handle 20A continuous current and reach 25A peak current.
The motor solder pads are reinforced by thick copper and edge plating technology, allowing lower resistance for more current on motors.
F411 4S 20A FC V5 reserves the UART ports layout, UART1 for RX, UART2 for DJI OSD or Analog VTX, and UART6 for spare usage, more convenient for pilots to solder.
Come with a 25.5x25.5mm whoop mounting pattern, this board can be added to both the toothpick drone and the cinematic whoop quadcopter frame like Pavo25 and X-knight 35


The board integrates 3 LEDs, including the Power LED (Red), FC LED(Blue) and Receiver LED.

Connecting External RX/HD Digital VTXF411 4S 20A FC V5 integrates the Plug &amp Play port for the external RX and HD digital VTX, and there will be a 4-pin connector for RX and a 6-pin connector for HD digital VTX in the package. Thus, we highly recommend pilots use the port to save the solder work.
.



 
FC &amp ESC FirmwareThe default firmware is including CLI dump file. But if you flash firmware from the Betaflight configurator official site, please flash a CLI dump file for F411 4S 20A FC V5. We offer the default firmware and CLI dump file to download.

Download the FC default firmware betaflight_4.3.x_BETAFPVF411 and CLI dump file.

BMI270 gyro will need more software filters and is sensitive in high frequency. This can be solved by adjusting filter settings in PID tuning. The Betaflight official or BETAFPV default FC firmware and CLI dump file do not include the filter settings. For pilots who want to configure it, we recommend setting gyro lowpass 2 at 145Hz and choosing filter type at PT2.

F411 4S 20A FC V5 is available to flash both BLHeli_S and BLUEJAY ESC firmware and it comes with default BLHeliI_S firmware. The main difference is that the BLUEJAY firmware supports bidirectional D-shot, while BLHeli_S does not support it. Here are the download links for two firmware.When using BLHeli_S ESC firmware, please configure the settings on BLHeli - Configurator software.

Download the BLHeli_S ESC firmware
Download the BLHeliSuite16714902a 
Download the BLHeli - Configurator
Download the ESC - Configurator

We offer the BLUEJAY ESC firmware for pilots. When using BLUEJAY ESC firmware, please configure the ESC on ESC-Configurator software.

Download the BLUEJAY ESC firmware
Download the ESC - Configurator
Download the Bluejay Configurator

Recommend Parts

Motors: 1404 Brushless Motors, 1506 Brushless Motors
Battery: 2S 600mAh, 3S/4S 850mAh, 4S 750mAh, or 4S 1000mAh
Frame: Pavo25 Frame, X-knight 35, or other frames with whoop mounting pattern

Specifications
Flight Controller:

CPU: STM32F411CEU6 (100MHZ)
Six-Axis: BMI270 (SPI connection)
Mounting Size: 25.5x25.5mm (M2 Anti-vibration rubber damper available)
FC Firmware: betaflight_4.3.x_BETAFPVF411
OSD: Built-in Betaflight OSD (OSD chip: AT7456E)
Receiver: SBUS/CRSF/DSMX Receiver
BEC: 5V 3A
Built-in current sensor
Weight: 8.15g

ESC:

ESC Chip: SILABS EFM8BB21F16G-C
Support D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Input voltage: 2S-4S Lipo
Continuous current: 20A
Peak current: 25A
Firmware: G_H_20_REV16_7.HEX (Default BLHeli_S), BLUEJAY (Optional)


Note: F411 4S 20A FC V5 is available to flash both BLHeli_S and BLUEJAY ESC firmware and it comes with default BLHeliI_S firmware. The main difference is that the BLUEJAY firmware supports bidirectional D-shot, while BLHeli_S does not support it.
Includes

1x BetaFPV F411 2-4S 20A Whoop/Toothpick Flight Controller V5 8bit 4in1 ESC BLHeli_S - BMI270
1x Cable Pigtail (XT30)
1x 6-Pin Connector for Digital VTX
1x 4-Pin Connector for RX
4x M2x12 Screws
8x M2 Nuts 
4x M2 Anti-vibration rubber dampers

Diagram



As a continuance of the F411 chip, the V5 FC board is upgraded from the F4 20A V3 FC board. F411 4S 20A Toothpick Brushless Flight Controller V5 adopts BMI270 gyro instead of MPU6000 on V3 board. With two integrated plug &amp; play ports for receiver and HD digital VTX, it is easy to install and requires less solder wo

BetaFPV F411 V5 2-4S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bit 4in1 ESC) - BMI270

BetaFPV F411 V5 2-4S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bi

As a continuance of the F411 chip, the V5 FC board is upgraded from the F4 20A V3 FC board. F411 4S 20A Toothpick Brushless Flight Controller V5 adopts BMI270 gyro instead of MPU6000 on V3 board. With two integrated plug&ampplay ports for receiver and HD digital VTX, it is easy to install and requires less solder work. Besides, the board is a solid value for durable use thanks to the high-quality PCB material and enhanced production process.

Bullet Point

With a large pad to solder, it is easy to solder external electronics. In addition, the V5 board features plug&ampplay ports for the receiver and HD digital VTX, which requires less solder work for convenient installation.
High-quality MOSFETs are applied to F411 4S 20A FC V5 to handle 20A continuous current and reach 25A peak current.
The motor solder pads are reinforced by thick copper and edge plating technology, allowing lower resistance for more current on motors.

F411 4S 20A FC V5 reserves the UART ports layout, UART1 for RX, UART2 for DJI OSD or Analog VTX, and UART6 for spare usage, more convenient for pilots to solder.
Come with a 25.5*25.5mm whoop mounting pattern, this board can be added to both the toothpick drone and the cinematic whoop quadcopter frame like Pavo25 and X-knight 35.

Specification
Flight Controller










CPU: STM32F411CEU6 (100MHZ)
Six-Axis: BMI270 (SPI connection)
Mounting Size: 25.5*25.5mm (M2 Anti-vibration rubber damper available)
FC Firmware: betaflight_4.3.x_BETAFPVF411
OSD: Built-in Betaflight OSD (OSD chip: AT7456E)
Receiver: SBUS/CRSF/DSMX Receiver
BEC: 5V 3A
Built-in current sensor
Weight: 8.15g

ESC

ESC Chip: SILABS EFM8BB21F16G-C
Support D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Input voltage: 2S-4S Lipo
Continuous current: 20A
Peak current: 25A
Firmware: G_H_20_REV16_7.HEX (Default BLHeli_S), BLUEJAY (Optional)


Note: F411 4S 20A FC V5 is available to flash both BLHeli_S and BLUEJAY ESC firmware and it comes with default BLHeliI_S firmware. The main difference is that the BLUEJAY firmware supports bidirectional D-shot, while BLHeli_S does not support it. 
Comparison to F411 4S 20A V3 FC
We upgraded the F411 4S 20A V3 board to V5 by adopting BMI270 gyro instead of MPU6000 and adding some new features. BMI270 gyro works great in most cases, especially in low frequency. Unlike the V3 board that supports JST1.25 connectors, the motor solder pads on V5 board are solderable only and reinforced by thick copper and edge plating technology, allowing lower resistance for more current on motors. Besides, the V5 FC board features high-quality material for the stability of the solder and durability of use. The below pictures show the difference between the two flight controllers.

Diagram for Toothpick F411 4S 20A Brushless FC V5
The board integrates 3 LEDs, including the Power LED (Red), FC LED(Blue) and Receiver LED.




LED
Status
Description


Power LED (Red)
Solid
Power on


FC LED (Blue)
Flashing
Motor Disarmed



FC LED (Blue)
Solid
Motor Armed



Receiver LED (Orange)
Solid
Connected Successfully



Connecting External RX/HD Digital VTX
F411 4S 20A FC V5 integrates the Plug &amp Play port for the external RX and HD digital VTX, and there will be a 4-pin connector for RX and a 6-pin connector for HD digital VTX in the package. Thus, we highly recommend pilots use the port to save the solder work.



FC &amp ESC Firmware
The default firmware is including CLI dump file. But if you flash firmware from the Betaflight configurator official site, please flash a CLI dump file for F411 4S 20A FC V5. We offer the default firmware and CLI dump file to download.

Download the FC default firmware betaflight_4.3.x_BETAFPVF411 and CLI dump file.

BMI270 gyro will need more software filters and is sensitive in high frequency. This can be solved by adjusting filter settings in PID tuning. The Betaflight official or BETAFPV default FC firmware and CLI dump file do not include the filter settings. For pilots who want to configure it, we recommend setting gyro lowpass 2 at 145Hz and choosing filter type at PT2.


F411 4S 20A FC V5 is available to flash both BLHeli_S and BLUEJAY ESC firmware and it comes with default BLHeliI_S firmware. The main difference is that the BLUEJAY firmware supports bidirectional D-shot, while BLHeli_S does not support it. Here are the download links for two firmware.
When using BLHeli_S ESC firmware, please configure the settings on BLHeli - Configurator software.

Download the BLHeli_S ESC firmware.

Download the BLHeliSuite16714902a. 
Download the BLHeli - Configurator.
Download the ESC - Configurator.

We offer the BLUEJAY ESC firmware for pilots. When using BLUEJAY ESC firmware, please configure the ESC on ESC-Configurator software.

Download the BLUEJAY ESC firmware.
Download the ESC - Configurator.

Download the Bluejay Configurator.

Recommend Parts


Motors: 1404 Brushless Motors, 1506 Brushless Motors

Battery: 2S 600mAh, 3S/4S 850mAh, 4S 750mAh, or 4S 1000mAh

Frame: Pavo25 Frame, X-knight 35, or other frames with whoop mounting pattern.


Package


1 * F411 4S 20A Toothpick Brushless Flight Controller V5 BLHeli_S (BMI270)
1 * Cable Pigtail (XT30)
1 * 6-Pin Connector for Digital VTX

1 * 4-Pin Connector for RX

4 * M2x12 Screws
8 * M2 Nuts 
4 * M2 Anti-vibration rubber dampers



As a continuance of the F411 chip, the V5 FC board is upgraded from the F4 20A V3 FC board. F411 4S 20A Toothpick Brushless Flight Controller V5 adopts BMI270 gyro instead of MPU6000 on V3 board. With two integrated plug&amp;play ports for receiver and HD digital VTX, it is easy to install and requires less solder work

F411 4S 20A Toothpick Brushless Flight Controller V5 BLHeli_S (BMI270)

Happymodel

HappyModel CruxF405HD 2-4S F4 20x20 AIO Flight Controller - 20A 8Bit 4in1 ESC, 2.4GHz ELRS RX

HAPPYMODEL

The CruxF405HD ELRS AIO flight controller comes with integrated UART 2.4GHz ExpressLRS receiver and 20A Blheli_s ESC(Bluejay firmware pre-installed) which could support 2-4s battery. Bigger Mosfet could support high to 20A currents would be better for 2-4S toothpick drone or long range FPV drone. Reserved 6 pin socket for DJI HD equipment plug and play. It’s a great solution of build HD digital FPV drone .
Check out our other AIO flight controllers, and the rest of our Happymodel offerings.

NOTES: If upgrade firmware to betaflight 4.4.x , need to add custom Defines “GYRO_SPI_ICM42688P ACC_SPI_ICM42688P” from build configuration of Betaflight configurator otherwise gyro may not be recognized. 
Features


Integrated UART 2.4GHz ExpressLRS receiver and 
20A Blheli_s ESC(Bluejay firmware pre-installed) 
Big Mosfets that support high 20A currents
Great for 2-4S toothpick
Reserved 6 pin socket for DJI HD equipment plug &amp play.

 
Specifications

Flight controller 

MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
GYRO Sensor: ICM42688 (SPI connection)
Mount hole size: 20mm*20mm
Power supply: 2~4S battery input (DC 8.7V-17.4V)
Built-in 20A(each) Blheli_S 4in1 ESC
Built-in Serial ExpressLRS 2.4G (Default connected to UART2)
Built-in BMP280 Barometer
Built-in 8MBp blackbox
Built-in voltage meter sensor , voltage meter scale 110
Built-in current meter sensor , current meter scale 470
Flight controller firmware target: BETAFLIGHTF4

4in1 ESC (MCU upgraded to EFM8BB21)

Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Currents: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: Bluejay 0.19.2
Firmware target: F_H_40_48_v0.19.2
Default protocol: DSHOT150/DSHOT300/DSHOT600

UART ExpressLRS 2.4GHz 

Receiver Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHz
Antenna plug: IPEX
Telemetry output Power: &lt12dBm
Receiver protocol: CRSF
Default firmware version: ExpressLRS V3.0.1

Voltage and Amperage meters settings 

Voltage meter scale setting 110
Amperage meter scale setting 470

Includes

1x HappyModel CruxF405HD 2-4S F4 AIO 20x20 Flight Controller (w/ 20A 8Bit 4in1 ESC &amp 2.4GHz ELRS RX)
1x XT30 Pigtail
1x ELRS T Antenna
4x Rubber Grommets
4x Motor Plugs


Binding
Binding procedure:

Supply power to the flight controller by plug USB, wait until the red LED on the FC is off, immediately turn off the power, and then repeat again the above steps. When the FC is powered on for the third time, the red LED light will start to double-flash, which means that the Receiver enters the binding mode
Please make sure your ExpressLRS tx module firmware is v3.x.x. And go to ExpressLRS.lua from “TOOLS” menu of your radio transmitter. Then hit [Bind] to binding with the onboard ExpressLRS receiver. The red LED should blinking slowly first then turn to solid, that means binding was successfully. If the red led keep tri-flash after binding ,please change Model Match tab value from “off” to “on” or from “on” to “off”

Receiver LED status meanings:
Red LED solid means bind successful or RC link established Red LED double-flash means get into bind mode Red LED flash slowly means no RC signal input from TX module Red LED continuous flash fast means ExpressLRS wifi enabled Red LED tri-flash means model mismatch need to change model match from “off” to “on”.
UART description:ELRS receiver was connected to UART2 default out of factory.Usually UART1 or UART6 Could be used for MSP OSD with HD VTX.UART6 could be used for GPS or other serial equipment.IRX6 is an inverted serial RX6 for SBUS input.IRX6 and TX6/RX6 couldn’t be used at the same time.

The world’s first AIO 5in1 F4 flight controller with integrated SPI 2.4GHz ExpressLRS receiver has been launched. The flight controller integrates SPI controlled 2.4GHz ExpressLRS receiver, Dshot protocol 4-in-1 ESC, 5.8GHz 40ch video transmitter and Betaflight OSD. Ultra-small size and ultra-stable remote control range can improve the range of the original SPI receiver. And because the 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate and low latency, this flight controller is the one that all Race/Freestyle pilots needed. It is suitable for use in Tiny whoop Race or Toothpick Freestyle, and can also be used in 1S ultra-lightweight Nano Long Range platform.

HappyModel CruxF405HD 2-4S F4 AIO 20x20 Flight Controller (w/ 20A 8Bit 4in1 ESC & 2.4GHz ELRS RX)

HappyModel ELRS 2G4 Whoop Flight Controller - For Sale At RaceDayQuads

The CruxF405HD ELRS AIO flight controller comes with integrated UART 2.4GHz ExpressLRS receiver and 20A Blheli_s ESC(Bluejay firmware pre-installed) which could support 2-4s battery. Bigger Mosfet could support high to 20A currents would be better for 2-4S toothpick drone or long range FPV drone. Reserved 6 pin socket 

Happymodel CruxF405 HD AIO Flight Controller 2-4S 20A ESC-UART ELRS 2.4GHz- 20x20mm

iFlight Blitz Whoop F7 2-6S AIO Fight Controller - 55A 8Bit 4in1 ESC

This is our new iFlight BLITZ series AIO FCs for your ultimate build. A future proof all-in-one FC to step up the game and make some more room for future flight firmware development like Betaflight, Emuflight etc. Lightweight, minimum size, minimum work.This could only be achieved by using BGA chipsets instead of ordinary QFP (big size) MCUs and ultra powerful Mosfets for almost any build. Solder your motor wires on and let's go! 
 Check out our other AIO FCs, as well as the rest of our iFlight selection!
Features

Separated Flight Control board to minimize electrical gyro noise
Pass-through DJI O3 and Caddx Vista/Polar Connector
FC PCB can be disassembled from the ESC PCB Repair allowed!
MCU: BGA-STM32F745, 216MHz
OSD: AT7456E
Blackbox: 16MB Onboard Flash
Gyro: BMI270

Specifications

FC Specifications


MCU: BGA-STM32F745
Gyro: BMI270
Blackbox: 16MB Onboard Flash
BEC output: 5V 2.5A 
WS2812 LED Strip: Yes
Buzzer: Yes
Barometer: DPS310
Connector: Micro-USB
OSD: IFLIGHT OSD (AT745E）
FC Firmware：IFLIGHT_BLITZ_F7_AIO
Mounting pattern: 25.5 x 25.5mm φ3mm
Dimensions: 35mm x 35mm
Weight: 10.5g 
BEC: 5V 2A / 3A
Input voltage: 2-6S, support LIHV battery
Smartaudio / IRC Tramp VTX protocol supported




ESC Specifications


ESC MCU: BB21
Driver: FD6288
Input voltage: 2-6S Support LIHV battery
Output current: 55A, peak value 65A (10 seconds)
ESC firmware: Q-H-40 - Bluejay, 0.16, 24kHz
Current sensor: ratio 200 (1/10mV/A)
BEC: NO
ESC Telemetry: NO
Bidirectional DShot: Yes(need to use Bluejay firmware)
Supports DShot DShot150/300/600/MultiShot/ OneShot etc.



Includes

iFlight Blitz Whoop F7 AIO V1.1 (w/ 55A 8Bit 4in1 ESC)
2 x Capacitor 470uF/35V
1 x XT30U Male 18AWG cable 70mm
1 x 1.0-7P cable 50mm-28mm
1 x 1.0-7P cable 50mm
4 x M2 silicon grommets
8 x M2x12mm screws
8 x M2 Transparent Nylon Nut
10 x 0.8mm black Heat shrink tube 10mm


Wiring Diagram


This is our new iFlight BLITZ series AIO FCs for your ultimate build. A future proof all-in-one FC to step up the game and make some more room for future flight firmware development like Betaflight, Emuflight etc. Lightweight, minimum size, minimum work.This could only be achieved by using BGA chipsets instead of ordin

iFlight Blitz Whoop F7 AIO [V1.1] 2-6S AIO Toothpick / Whoop Flight Controller (w/ 55A 8Bit 4in1 ESC)

iFlight Blitz Whoop F7 AIO [V1.1] 2-6S AIO Toothpick / Whoop Flight Co

NewBeeDrone x ImmersionRC BeeBrain BLV4 AIO Flight Controller - Ghost Rx


NewBeeDrone x ImmersionRC BeeBrain BLV4 Built in Ghost Rx

Warning! The BeeBrainBLV4 OSD might not compatible with third party camera. If you are planning to use it for customized build, Please be aware it only support the camera below: 
NewBeeDrone BeeEye CameraRuncam Nano4 
BeeBrain BLV4 GHOST Spec:MCU: STM32F411GYRO：BMI270VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw)  with BeeTX 5.8Ghz AntennaESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHzESC Connector: JST-1.0 3PinOSD: NBD7456 Graphical OSD compatible with Betaflight OSDReceiver: GHOST 2.4G receiver with GHOST 2.4G qT AntennaFlight Controller Weight: 6.5g(Include antennas and battery connector)Flight Controller Size: Outer dimensions: 29x29x7.6mmFlight Controller Holes: 25.5x25.5mmBattery input: 1SUart2: Tx for GHOST 2.4G ReceiverUart1:  Tx&ampampRx freePower Connector: 

NBD-PH2.0 connector

Includes

1 x BeeBrain BLV4 GHOST Flight Controller
4 x Grommet
4 x Screw
1 x qT Antenna

1 x VTX Antenna



Firmware: 1. BeeBrain BLV4 GHOST Betaflight 4.4  firmware 
All New firmware can be found on our Github Page
 
Terms and Condition:
We would like to remind you that our flight controller product is designed to work with our own product line. While we have taken every possible measure to ensure the quality and compatibility of our product line, using third party components may result in incompatibility or improper functioning of the product. such as Camere with different voltage signal will mass up the OSD function, frame from other company that is not fitting well with our FC, Motor plug are not compatible with the JST1.0 on the FC. etc. 
We strongly recommend that you verify the compatibility and functioning before any soldering or modification. 
Please be aware, drone flight controller will break due to crash, any physical damage or crash will have posibility to destory the hardware. This is also not cover by our warranty.  If you find that the product is Dead On Arrival (DOA), we will replace it for you free of charge.
However, we cannot take responsibility for any issues that may arise due to modifications made to the product or the use 3rd party components. In such cases, we will not be able to provide support or warranty coverage. 
Wire Diagram:

NewBeeDrone x ImmersionRC BeeBrain BLV4 Built in Ghost Rx Warning! The BeeBrainBLV4 OSD might not compatible with third party camera. If you are planning to use it for customized build, Please be aware it only support the camera below:  NewBeeDrone BeeEye CameraRuncam Nano4  BeeBrain BLV4 GHOST Spec:MCU: STM32F411GYRO：

NewBeeDrone x ImmersionRC BeeBrain BLV4 Built-in Ghost Rx AIO Flight Controller from WREKD Co.

NewBeeDrone x ImmersionRC BeeBrain BLV4 Built-in Ghost Rx AIO Flight Controller


NewBeeDrone x ImmersionRC BeeBrain BLV4 Built in Ghost Rx

Warning! The BeeBrainBLV4 OSD might not compatible with third party camera. If you are planning to use it for customized build, Please be aware it only support the camera below: 
NewBeeDrone BeeEye CameraRuncam Nano4 
BeeBrain BLV4 GHOST Spec:MCU: STM32F411GYRO：BMI270VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw)  with BeeTX 5.8Ghz AntennaESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHzESC Connector: JST-1.0 3PinOSD: NBD7456 Graphical OSD compatible with Betaflight OSDReceiver: GHOST 2.4G receiver with GHOST 2.4G qT AntennaFlight Controller Weight: 6.5g(Include antennas and battery connector)Flight Controller Size: Outer dimensions: 29x29x7.6mmFlight Controller Holes: 25.5x25.5mmBattery input: 1SUart2: Tx for GHOST 2.4G ReceiverUart1:  Tx&ampRx freePower Connector: 

NBD-PH2.0 connector

Includes

1 x BeeBrain BLV4 GHOST Flight Controller
4 x Grommet
4 x Screw

1 x qT Antenna
1 x VTX Antenna



Firmware: 1. BeeBrain BLV4 GHOST Betaflight 4.4  firmware 
All New firmware can be found on our Github Page
 
Terms and Condition:
We would like to remind you that our flight controller product is designed to work with our own product line. While we have taken every possible measure to ensure the quality and compatibility of our product line, using third party components may result in incompatibility or improper functioning of the product. such as Camere with different voltage signal will mass up the OSD function, frame from other company that is not fitting well with our FC, Motor plug are not compatible with the JST1.0 on the FC. etc. 
We strongly recommend that you verify the compatibility and functioning before any soldering or modification. 
Please be aware, drone flight controller will break due to crash, any physical damage or crash will have posibility to destory the hardware. This is also not cover by our warranty.  If you find that the product is Dead On Arrival (DOA), we will replace it for you free of charge.
However, we cannot take responsibility for any issues that may arise due to modifications made to the product or the use 3rd party components. In such cases, we will not be able to provide support or warranty coverage. 
Wire Diagram:

NewBeeDrone x ImmersionRC BeeBrain BLV4 Built-in Ghost Rx AIO Flight C

NewBeeDrone x Team BlackSheep BeeBrain BLV4 AIO Flight Controller - 12A ESC, Crossfire Rx

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built in Crossfire Rx
Warning:

We would like to remind you that our flight controller product is designed to work with our own product line. While we have taken every possible measure to ensure the quality and compatibility of our product line, using third party components may result in incompatibility or improper functioning of the product. such as Camere with different voltage signal will mass up the OSD function, frame from other company that is not fitting well with our FC, Motor plug are not compatible with the JST1.0 on the FC. etc. 
We strongly recommend that you verify the compatibility and functioning before any soldering or modification. 

Please be aware, drone flight controller will break due to crash, any physical damage or crash will have posibility to destory the hardware. This is also not cover by our warranty.  If you find that the product is Dead On Arrival (DOA), we will replace it for you free of charge.
However, we cannot take responsibility for any issues that may arise due to modifications made to the product or the use 3rd party components. In such cases, we will not be able to provide support or warranty coverage. 

Thank you for your understanding and for choosing our product. If you have any questions or concerns, please don't hesitate to contact our customer support team.
This product is designed mainly to be a replacement part for the NewBeeDrone x Team BlackSheep AcroBee65 BLV4 Crossfire. 

BeeBrain BLV4 CRSF Spec:
MCU: STM32F411GYRO：BMI270VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw)  with BeeTX 5.8Ghz AntennaESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHzESC Connector: JST-1.0 3PinOSD: NBD7456 Graphical OSD compatible with Betaflight OSDReceiver: Crossfire Nano receiver with MINIMORTAL T ANTENNAFlight Controller Weight: 6.5g(Include antennas and battery connector)Flight Controller Size: Outer dimensions: 29x29x7.6mmFlight Controller Holes: 25.5x25.5mmBattery input: 1SUart2: Crossfire Nano receiver 
Power Connector: NBD-PH2.0 connector
Includes


1 x BeeBrain BLV4 CRSF Flight Controller
4 x Grommet
4 x Screw

1 x MINIMORTAL T Antenna
1 x VTX Antenna




Firmware: 1. BeeBrain BLV4 CRSF Betaflight 4.4  firmware 
All New firmware can be found on our Github Page

All firmware can be found on our Github PageWire Diagram:
 

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built in Crossfire Rx Warning: We would like to remind you that our flight controller product is designed to work with our own product line. While we have taken every possible measure to ensure the quality and compatibility of our product line, using third party components ma

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built-in Crossfire Rx AIO Flight Controller

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built-in Crossfire Rx AIO 

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built in Crossfire Rx
Warning:

We would like to remind you that our flight controller product is designed to work with our own product line. While we have taken every possible measure to ensure the quality and compatibility of our product line, using third party components may result in incompatibility or improper functioning of the product. such as Camere with different voltage signal will mass up the OSD function, frame from other company that is not fitting well with our FC, Motor plug are not compatible with the JST1.0 on the FC. etc. 
We strongly recommend that you verify the compatibility and functioning before any soldering or modification. 

Please be aware, drone flight controller will break due to crash, any physical damage or crash will have posibility to destory the hardware. This is also not cover by our warranty.  If you find that the product is Dead On Arrival (DOA), we will replace it for you free of charge.
However, we cannot take responsibility for any issues that may arise due to modifications made to the product or the use 3rd party components. In such cases, we will not be able to provide support or warranty coverage. 

Thank you for your understanding and for choosing our product. If you have any questions or concerns, please don&#39t hesitate to contact our customer support team.
This product is designed mainly to be a replacement part for the NewBeeDrone x Team BlackSheep AcroBee65 BLV4 Crossfire. 

BeeBrain BLV4 CRSF Spec:
MCU: STM32F411GYRO：BMI270VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw)  with BeeTX 5.8Ghz AntennaESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHzESC Connector: JST-1.0 3PinOSD: NBD7456 Graphical OSD compatible with Betaflight OSDReceiver: Crossfire Nano receiver with MINIMORTAL T ANTENNAFlight Controller Weight: 6.5g(Include antennas and battery connector)Flight Controller Size: Outer dimensions: 29x29x7.6mmFlight Controller Holes: 25.5x25.5mmBattery input: 1SUart2: Crossfire Nano receiver 
Power Connector: NBD-PH2.0 connector
Includes


1 x BeeBrain BLV4 CRSF Flight Controller
4 x Grommet
4 x Screw

1 x MINIMORTAL T Antenna
1 x VTX Antenna




Firmware: 1. BeeBrain BLV4 CRSF Betaflight 4.4  firmware 
All New firmware can be found on our Github Page

All firmware can be found on our Github PageWire Diagram:
 

NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built-in Crossfire Rx AIO Flight Controller from WREKD Co.

NEWBEEDRONE

The NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller provides optimal performance for pilots who want a compact build. This single board is equipped with a flight controller, 12A 32Bit 4in1 ESC, 5.8GHz VTX, and a TBS Crossfire receiver, all on a 29x29mm platform. Enjoy advanced features and excellent performance for your compact setup! 
The new "Smart Max" technology uses the MCU to read the board temperature on the back of the VTEC chip and uses PID control to control the output power of the VTX amplifier. When the board temperature rises, the VTX power will be automatically reduced. When the temperature is low, the maximum output power can be up to 400mW. If
Check out all our Whoop/AIO Flight Controllers and the rest of our NewBeeDrone products.
Features

Built-In TBS Crossfire Nano Receiver
SmartMAX (SmartMax up to 400mw) 
25x25 Mounting Pattern
5w/25w Switchable VTX
F411 Flight Controller
12A BLHeli_S ESC
1-2S Voltage
BMI270 Gyro

Specifications

MCU: STM32F411
GYRO：BMI270
VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw) with BeeTX 5.8Ghz Antenna
ESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHz
ESC Connector: JST-1.0 3Pin
OSD: NBD7456 Graphical OSD compatible with Betaflight OSD
Receiver: Crossfire Nano receiver with MINIMORTAL T ANTENNA
Flight Controller Weight: 6.5g(Include antennas and battery connector)
Flight Controller Size: Outer dimensions: 29x29x7.6mm
Flight Controller Holes: 25.5x25.5mm
Battery input: 1-2S (For 2S you will need to set throttle cap at less 50%)
Uart2: Crossfire Nano receiver 
Power Connector: NBD-PH2.0 connector

Additional Information

UART2 TX and RX for onboard Crossfire (CRSF)

UART1 TX and RX free

VTX Adjustable power 5mW-25mW-SmartMAX. SmartMAX will automatically adjust the VTX power according to the board temperature. When the board temperature rises, the VTX power will be automatically reduced. When the temperature is low, the maximum output power can be up to 400mW.

Firmware 

Download: BeeBrain BLV4 CRSF Betaflight 4.4 firmware


Includes

1x NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller w/ 12A 8Bit 4in1 ESC &amp 400mW VTX - CRSF
4x Grommet
4x Screw

1x Receiver T-Antennas 


1x Receiver Mono Pole Antenna


1x VTX Antenna


Wiring Diagram 


The NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller provides optimal performance for pilots who want a compact build. This single board is equipped with a flight controller, 12A 32Bit 4in1 ESC, 5.8GHz VTX, and a TBS Crossfire receiver, all on a 29x29mm platform. Enjoy advanced features and exc

NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller w/ 12A 8Bit 4in1 ESC & 400mW VTX - CRSF

NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Control

The NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller provides optimal performance for pilots who want a compact build. This single board is equipped with a flight controller, 12A 32Bit 4in1 ESC, 5.8GHz VTX, and a TBS Crossfire receiver, all on a 29x29mm platform. Enjoy advanced features and excellent performance for your compact setup! 
The new &quotSmart Max&quot technology uses the MCU to read the board temperature on the back of the VTEC chip and uses PID control to control the output power of the VTX amplifier. When the board temperature rises, the VTX power will be automatically reduced. When the temperature is low, the maximum output power can be up to 400mW. If
Check out all our Whoop/AIO Flight Controllers and the rest of our NewBeeDrone products.
Features

Built-In TBS Crossfire Nano Receiver
SmartMAX (SmartMax up to 400mw) 
25x25 Mounting Pattern
5w/25w Switchable VTX
F411 Flight Controller
12A BLHeli_S ESC
1-2S Voltage
BMI270 Gyro

Specifications

MCU: STM32F411
GYRO：BMI270
VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw) with BeeTX 5.8Ghz Antenna
ESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHz
ESC Connector: JST-1.0 3Pin
OSD: NBD7456 Graphical OSD compatible with Betaflight OSD
Receiver: Crossfire Nano receiver with MINIMORTAL T ANTENNA
Flight Controller Weight: 6.5g(Include antennas and battery connector)
Flight Controller Size: Outer dimensions: 29x29x7.6mm
Flight Controller Holes: 25.5x25.5mm
Battery input: 1-2S (For 2S you will need to set throttle cap at less 50%)
Uart2: Crossfire Nano receiver 
Power Connector: NBD-PH2.0 connector

Additional Information

UART2 TX and RX for onboard Crossfire (CRSF)

UART1 TX and RX free

VTX Adjustable power 5mW-25mW-SmartMAX. SmartMAX will automatically adjust the VTX power according to the board temperature. When the board temperature rises, the VTX power will be automatically reduced. When the temperature is low, the maximum output power can be up to 400mW.

Firmware 

Download: BeeBrain BLV4 CRSF Betaflight 4.4 firmware


Includes

1x NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller w/ 12A 8Bit 4in1 ESC &ampamp 400mW VTX - CRSF
4x Grommet
4x Screw

1x Receiver T-Antennas 


1x Receiver Mono Pole Antenna


1x VTX Antenna


Wiring Diagram 


NewBeeDrone BeeBrain BLV4 F411 1-2S AIO Whoop/Toothpick Flight Controller w/ 12A 8Bit 4in1 ESC & 400mW VTX - CRSF from WREKD Co.

NewBeeDrone Infinity200 F4 3-6S 20x20 Flight Controller for DJI

 
Note: the Infinity200 FC now uses a USB-C connector.
-Infinity200 Flight Controller Firmware on Official BetaflightTarget name: NBD_INFINITYF4
Flight Controller Spec:

MPU6000 Gyro
STM32F405 CPUE @ 168mhz, can be overclocked
3-6S direct battery input
5V 2A
9V 2A 18W Design for DJI FPV Air Unit
5V Camera Power
betaflight OSD
31.5x27 CB with 20x20 mounting holes, weight: 5.85g
6 UARTS. UART1 (INVERTER FOR SBUS)
UART2 (FREE)
UART3 (INVERTED TELEMETRY)
UART4 (Free)
UART5 (Smart Audio)
UART6(Free)
Built-in 4 IN 1 ESC socket(including ESC telemetry, External current sensor) JST1.0 8Pin
Plug and plug with NBD Infinity200 ESC. Also compatible with most of the ESC on the market.
Built-in solder pads for ESC signal output and power
Printed layout instructions ON the board - no need for instructions!
DJI FPV Air Unit socket (use UART1 and UART6)

Pinout for USB-C Version (Recent)


Pinout for Micro USB Version

Includes:

1x Infinity200 flight controller
4x Grommets short 4x Grommets Long
1x Infinity200 FC to DJI Air module cable 40mm
1x Infinity200 FC to DJI Air module cable 100mm
1x Infinity200 FC to DJI Air module cable 150mm

NOTE: We suggest running a Electrolytic capacitor on 4s builds. Even though we tested and designed it to not need one, all builds are different and there are always exceptions.



  Note: the Infinity200 FC now uses a USB-C connector. -Infinity200 Flight Controller Firmware on Official BetaflightTarget name: NBD_INFINITYF4 Flight Controller Spec: MPU6000 Gyro STM32F405 CPUE @ 168mhz, can be overclocked 3-6S direct battery input 5V 2A 9V 2A 18W Design for DJI FPV Air Unit 5V Camera Power betaflig

NewBeeDrone Infinity200 F4 Flight Controller from WREKD Co.

NewBeeDrone Infinity200 F4 Flight Controller

-Infinity200 Flight Controller Firmware NBD Infinity Flight Controller 4.1.0 ﻿The same power and smoovness you can get in the Infinity 30x30 stack but smaller! For those looking for a DJI plug and play system for those small frame builds, this is a great option! Flight Controller Spec:• MPU6000 Gyro • STM32F405 CPUE @ 

NewBeeDrone Infinity200 20x20 BetaFlight Flight Controller

Note: the Infinity200 FC now uses a USB-C connector.
-Infinity200 Flight Controller Firmware on Official BetaflightTarget name: NBD_INFINITYF4
Flight Controller Spec:

MPU6000 Gyro
STM32F405 CPUE @ 168mhz, can be overclocked
3-6S direct battery input
5V 2A
9V 2A 18W Design for DJI FPV Air Unit
5V Camera Power
betaflight OSD
31.5x27 CB with 20x20 mounting holes, weight: 5.85g
6 UARTS. UART1 (INVERTER FOR SBUS)
UART2 (FREE)
UART3 (INVERTED TELEMETRY)
UART4 (Free)
UART5 (Smart Audio)
UART6(Free)
Built-in 4 IN 1 ESC socket(including ESC telemetry, External current sensor) JST1.0 8Pin
Plug and plug with NBD Infinity200 ESC. Also compatible with most of the ESC on the market.
Built-in solder pads for ESC signal output and power
Printed layout instructions ON the board - no need for instructions!
DJI FPV Air Unit socket (use UART1 and UART6)

Pinout for USB-C Version (Recent)


Pinout for Micro USB Version

Includes:

1x Infinity200 flight controller
4x Grommets short 4x Grommets Long
1x Infinity200 FC to DJI Air module cable 40mm
1x Infinity200 FC to DJI Air module cable 100mm
1x Infinity200 FC to DJI Air module cable 150mm

NOTE: We suggest running a Electrolytic capacitor on 4s builds. Even though we tested and designed it to not need one, all builds are different and there are always exceptions.



Note: the Infinity200 FC now uses a USB-C connector. -Infinity200 Flight Controller Firmware on Official BetaflightTarget name: NBD_INFINITYF4 Flight Controller Spec: MPU6000 Gyro STM32F405 CPUE @ 168mhz, can be overclocked 3-6S direct battery input 5V 2A 9V 2A 18W Design for DJI FPV Air Unit 5V Camera Power betaflight

NewBeeDrone Infinity V2 PRO 3-6S 30x30 AIO Flight Controller - 55A 32Bit ESC

NewBeeDrone Infinity AIO V2 is the next generation of Infinity AIO Flight Controller. NBD has invested an immense amount of R&ampD time to optimize the hardware between high current and signal processing layout to make the board extremely compact and with no interference. Additionally, by sealing every component inside the aluminum heatsink which acts like a shield to protect from dust and other conditions, NBD maximizes the physical toughness of the AIO stack.
The NewBeeDrone Infinity AIO V2 Pro is upgraded from AIO V2. Now it comes with Dual BMI270 Gyro. Better performance on handling noise and better reliability. Dual-Gyros allows device redundancy and also measurement redundancy. Having two gyros mounted to each other, the flight controller is able to cancel out the effects of a noisy axis on one of the IMUs to better handle strong winds and gusts, allowing smoother flight capabilities for filming aerial views.
Check out our AIO flight controllers, as well as the rest of our NewBeeDrone selection!
Specifications

Voltage Input: 3-6S
MCU: STM32F745VEH6
Gyro: 2xBMI270

Blackbox: 16MB
UARTs: 5
ESC MCU: SMT32G071 BLHELI32 
Max Continuous Current: 55A 
Max Burst Current: 65A
BEC: 10V 3A 30W Design for DJI FPV Air Unit
Betaflight OSD support Analog build

I2C: SCL &amp SDA ready
Buzzer: Yes
LED: Yes
5V 3A Power supply for external LED or GPS module
Mounting Pattern: 30.5x30.5 
Weight: 22g


Includes

1x NewBeeDrone Infinity V2 PRO 3-6S 30x30 AIO Flight Controller w/ 55A 32bit ESC
1x Infinity AIO V2 PRO to DJI Air Module Cable 100mm (Silicon wire)
1x Infinity AIO V2 PRO to DJI Air Module V2 Cable 100mm (Silicon wire)
2x Infinity AIO V2 PRO8 16Pin Cable 150mm (Teflon wire)
13x Nylon Lock Nut
5x Steel Screw M3x14
4x Grommets Short 4x Grommets Long
1x 470uf 35v Electrolytic Capacitor
1x XT60 Cable


NewBeeDrone Infinity AIO V2 is the next generation of Infinity AIO Flight Controller. NBD has invested an immense amount of R&amp;D time to optimize the hardware between high current and signal processing layout to make the board extremely compact and with no interference. Additionally, by sealing every component insid

NewBeeDrone Infinity V2 PRO 3-6S 30x30 AIO Flight Controller w/ 55A 32bit ESC

NewBeeDrone Infinity V2 PRO 3-6S 30x30 AIO Flight Controller w/ 55A 32

NewBeeDrone Infinity AIO V2 is the next generation of Infinity AIO Flight Controller. NBD has invested an immense amount of R&ampampD time to optimize the hardware between high current and signal processing layout to make the board extremely compact and with no interference. Additionally, by sealing every component inside the aluminum heatsink which acts like a shield to protect from dust and other conditions, NBD maximizes the physical toughness of the AIO stack.
The NewBeeDrone Infinity AIO V2 Pro is upgraded from AIO V2. Now it comes with Dual BMI270 Gyro. Better performance on handling noise and better reliability. Dual-Gyros allows device redundancy and also measurement redundancy. Having two gyros mounted to each other, the flight controller is able to cancel out the effects of a noisy axis on one of the IMUs to better handle strong winds and gusts, allowing smoother flight capabilities for filming aerial views.
Check out our AIO flight controllers, as well as the rest of our NewBeeDrone selection!
Specifications

Voltage Input: 3-6S
MCU: STM32F745VEH6
Gyro: 2xBMI270

Blackbox: 16MB
UARTs: 5
ESC MCU: SMT32G071 BLHELI32 
Max Continuous Current: 55A 
Max Burst Current: 65A
BEC: 10V 3A 30W Design for DJI FPV Air Unit
Betaflight OSD support Analog build

I2C: SCL &ampamp SDA ready
Buzzer: Yes
LED: Yes
5V 3A Power supply for external LED or GPS module
Mounting Pattern: 30.5x30.5 
Weight: 22g


Includes

1x NewBeeDrone Infinity V2 PRO 3-6S 30x30 AIO Flight Controller w/ 55A 32bit ESC
1x Infinity AIO V2 PRO to DJI Air Module Cable 100mm (Silicon wire)
1x Infinity AIO V2 PRO to DJI Air Module V2 Cable 100mm (Silicon wire)
2x Infinity AIO V2 PRO8 16Pin Cable 150mm (Teflon wire)
13x Nylon Lock Nut
5x Steel Screw M3x14
4x Grommets Short 4x Grommets Long
1x 470uf 35v Electrolytic Capacitor
1x XT60 Cable


NewBeeDrone Infinity V2 PRO 3-6S 30x30 AIO Flight Controller w/ 55A 32bit ESC from WREKD Co.

Infinity AIO V2 PRO Dual BMI270 Gyro
Note for DJI O3 User.For Canvas Mode (O3 +Airunits) Please enter these commands on CLIset osd_displayport_device = MSPset displayport_msp_serial = 2save
Please follow this solder instruction to complete the installation it will bring the best performance out of the InfinityAIO V2 PRO!  





Overview
NewBeeDrone Infinity AIO V2 Pro is Upgraded from AIO V2. Now it comes with Dual BMI270 Gyro. Better performance on handling noise and better reliability. 
Any requests from the V1, we have them on the V2. 
Our first-generation board was fully covered in heatsink and the components were sealed completely to provide better reliability and durability. Improving upon that, our V2 version is even better on weatherproofing and packed in all the requested features such as OSD Chips and more Uart ports. 
The AIO is truly the next level solution for flight controllers and ESCs. Based on our data from the Infinity AIO V1, not only was the AIO solution more compact but there were also less issues compared to stacks.  
We have invested immense amount of R&ampD time to optimize the hardware between high current and signal processing layout to make the board extremely compact and with no interference. Additionally, by sealing every component inside the aluminum heatsink which acts like a shield to protect from dusts and other conditions, we maximize the physical toughness of the AIO stack.
 Infinity AIO V2 Pro features dual-gyro for better flight handling.Dual-Gyros allows device redundancy and also measurement redundancy. Having two gyros mounted to each other, the flight controller is able to cancel out effects of a noisy axis on one of the IMU’s to better handle strong winds and gusts, allowing smoover flight capabilities for filming aerial views.
Specification:

MCU: STM32F745VEH6
Gyro: 2xBMI270
Blackbox:16MB
6-Pin DJI FPV Air Unit Connector
Micro USB Connector
UART1 - SBUS on DJI Connector (RX only)
UART2 - DJI Connector
UART3 - Free
UART7 - Free
UART8 - Free
4x SMT32G071 BLHELI32 ESC MCU
Continous Current 55A and 65A Burst ESC
3-6S Battery Input
12V 3A 30W Design for DJI FPV Air Unit
5x37mm with 30.5x30.5 Mounting Holes
Weight: 22gr. without grommets
Betaflight OSD support Analog build
I2C_SCL I2C_SDA Ready
Buzzer Ready
LED Ready
5V 3A Power supply for external LED or GPS module

 
Includes

1x Infinity AIO V2 PRO Flight Controller + ESC 
1x Infinity AIO V2 PRO to DJI Air Module Cable 100mm (Silicon wire) SH1.0 6Pin
1x Infinity AIO V2 PRO to DJI Air Module V2 Cable 100mm (Silicon wire) SH1.0 6Pin

2x Infinity AIO V2 PRO8 16Pin Cable 150mm (Teflon wire) JST0.8 16Pin 32AWG 
13x Nylon Lock Nut
5x Steel Screw M3x14
4x Grommets Short 4x Grommets Long
1x 470uf 35v Electrolytic Capacitor
1x XT60 Cable

 Firmware target name on official Betaflight GUI: NBD_INFINITYAIOV2PROif you are using the previous InfinityAIO generation, You can also find the target on official betaflight GUI, first generation is NBD_INFINITYAIOsecond generation is NBD_INFINITYAIOV2
Review Video: 

Infinity AIO V2 PRO Dual BMI270 Gyro Note for DJI O3 User.For Canvas Mode (O3 +Airunits) Please enter these commands on CLIset osd_displayport_device = MSPset displayport_msp_serial = 2save Please follow this solder instruction to complete the installation it will bring the best performance out of the InfinityAIO V2 PR

NewBeeDrone Infinity AIO V2 Pro

NewBeeDrone Infinity F7 3-6S AIO Flight Controller - 45A 32Bit 45A ESC


NewBeeDrone Infinity AIO 255 Flight Controller F7 MPU6000 45A 2-6S




Introducing the NewBeeDrone InfinitvAl0 255 F7 Flight Controller MPU6000 45A 2-6S. This all-in-one controller features a 25.5x25.5 mounting base, ideal for 3-4 inch lightweight builds. With motor solder pads on both sides and a traditional layout, it&#39s perfect for seamless integration into your setup. Plus, its MPU6000 and 45A 2-6S capability ensures superior performance and reliability. Ideal for drone enthusiasts looking for top-notch quality and seamless integration.
 



Specifications



MCU: STM32F745VEH6
Gyro: MPU6000
Blackbox:128MB
6-Pin DJI FPV Air Unit Connector
Micro USB Connector
UART1 - SBUS on DJI Connector (RX only)
UART2 - DJI Connector
UART3 – Free
UART5 – ESC
UART7 - Free
UART8 - Free
4x SMT32G071 BLHELI32 ESC MCU
Continous Current 45A and 55A Burst ESC
3-6S Battery Input
12V 3A 30W Design for DJI FPV Air Unit
37x32mm with 25.5x25.5 Mounting Holes
Weight: 10.2gr. without grommets
Betaflight OSD support Analog build
I2C_SCL I2C_SDA Ready
Buzzer Ready
LED Ready
5V 3A Power supply for external LED or GPS module



Includes



1x Infinity 255 AIO Flight Controller + ESC
1x DJI O3 Cable 100mm (Silicon wire)
2x 16Pin Cable 150mm (Teflon wire)
13x Nylon Lock Nut
5x Steel Screw M2x14
4x Grommets Short, 4x Grommets Long
1x 470uf 35v Electrolytic Capacitor
1x XT30 Cable



Media and Videos



Manuals and Downloads



Product Short Description
 




NewBeeDrone Infinity AIO 255 Flight Controller F7 MPU6000 45A 2-6S Introducing the NewBeeDrone InfinitvAl0 255 F7 Flight Controller MPU6000 45A 2-6S. This all-in-one controller features a 25.5x25.5 mounting base, ideal for 3-4 inch lightweight builds. With motor solder pads on both sides and a traditional layout, it's 

NewBeeDrone Infinity AIO 255 Flight Controller F7 MPU6000 45A 2-6S from WREKD Co.

NewBeeDrone Infinity AIO 255 Flight Controller F7 MPU6000 45A 2-6S


NewBeeDrone Infinity AIO 255 Flight Controller F7 MPU6000 45A 2-6S




Introducing the NewBeeDrone InfinitvAl0 255 F7 Flight Controller MPU6000 45A 2-6S. This all-in-one controller features a 25.5x25.5 mounting base, ideal for 3-4 inch lightweight builds. With motor solder pads on both sides and a traditional layout, it's perfect for seamless integration into your setup. Plus, its MPU6000 and 45A 2-6S capability ensures superior performance and reliability. Ideal for drone enthusiasts looking for top-notch quality and seamless integration.
 



Specifications



MCU: STM32F745VEH6
Gyro: MPU6000
Blackbox:128MB
6-Pin DJI FPV Air Unit Connector
Micro USB Connector
UART1 - SBUS on DJI Connector (RX only)
UART2 - DJI Connector
UART3 – Free
UART5 – ESC
UART7 - Free
UART8 - Free
4x SMT32G071 BLHELI32 ESC MCU
Continous Current 45A and 55A Burst ESC
3-6S Battery Input
12V 3A 30W Design for DJI FPV Air Unit
37x32mm with 25.5x25.5 Mounting Holes
Weight: 10.2gr. without grommets
Betaflight OSD support Analog build
I2C_SCL I2C_SDA Ready
Buzzer Ready
LED Ready
5V 3A Power supply for external LED or GPS module



Includes



1x Infinity 255 AIO Flight Controller + ESC
1x DJI O3 Cable 100mm (Silicon wire)
2x 16Pin Cable 150mm (Teflon wire)
13x Nylon Lock Nut
5x Steel Screw M2x14
4x Grommets Short, 4x Grommets Long
1x 470uf 35v Electrolytic Capacitor
1x XT30 Cable



Media and Videos



Manuals and Downloads



Product Short Description
 




The NewBeeDrone Infinity AIO is designed to be the board that can last forever. This workhorse is perfect for those looking for a simple solution and strong protection. A double-sided custom aluminum heatsink gives the board protection and a unique look.

The NewBeeDrone Infinity AIO is designed to be the board that can last forever. This workhorse is perfect for those looking for a simple solution and strong protection. A double-sided custom aluminum heatsink gives the board a unique look and provide

NewBeeDrone Infinity AIO F7 FC + 45A BLHeli_32 3-6S ESC

NewBeeDrone Galaxy AIO 255 Flight Controller - 45A ESC

NewBeeDrone Galaxy AIO 255
Specification:


MCU: STM32H743VIH6

Gyro: 2xBMI270

Blackbox: SDIO 512M SD

Baro：Infineon DPS310(I2C2)
6-Pin DJI FPV Air Unit Connector
Micro USB Connector
UART1 - Free
UART2 - Free
UART3 – Free
UART4- DJI Connector
UART6- SBUS on DJI Connector (RX only)
UART7 - Free

UART8 - ESC Telemetry

4x SMT32G071 BLHELI32 ESC MCU
Continuedly Current 45A and 55A Burst ESC
3-6S Battery Input

12V 2A 30W Design for DJI FPV Air Unit

34x34mm with 25.5x25.5 Mounting Holes
Weight: 10.8gr. without grommets
Betaflight OSD support Analog build
I2C_SCL I2C_SDA Ready
Buzzer Ready
LED Ready

5V 3A Power supply for external LED or GPS module


 
Includes

1x Galaxy AIO Flight Controller + ESC
1x Galaxy AIO DJI JST0.8 6Pin Cable 100mm (Teflon wire)
10x M2 Nylon Lock Nut
5x Steel Screw M2x14
4x Grommets short
1x 470uf 35v Electrolytic Capacitor
1x XT60 Cable
1x XT30 Cable





NewBeeDrone Galaxy AIO 255 Specification: MCU: STM32H743VIH6 Gyro: 2xBMI270 Blackbox: SDIO 512M SD Baro：Infineon DPS310(I2C2) 6-Pin DJI FPV Air Unit Connector Micro USB Connector UART1 - Free UART2 - Free UART3 – Free UART4- DJI Connector UART6- SBUS on DJI Connector (RX only) UART7 - Free UART8 - ESC Telemetry 4x SMT3

NewBeeDrone Galaxy AIO 255

NewBeeDrone Galaxy AIO 255 from WREKD Co.

HolyBro

Holybro Kakute G4 2-6S AIO Flight Controller - F4 AM32 35A 32Bit 4in1 ESC

HOLYBRO














The Holybro Kakute G473 AIO packs a ton of features into a compact and powerful flight controller + 4in1 ESC board. It's plug-and-play compatible with the DJI O3 VTX. It also works with analog systems due to the onboard OSD chip. The FC on this AIO uses a G4 processor, and the 4in1 ESC uses four F4 processors running AM32 firmware. Boasting an ICM-42688p gyro, 5V &amp 10V BEC, 16MB of flash storage &amp DSP310 baro. And with its super-hydrophobic, nano-waterproof coating, it weighs only 7.5g and provides protection from moisture and other elements.













Check out all our Whoop/AIO Flight Controllers, and the rest of our Holybro selection!
Features

AIO board with G4 Processor FC &amp F4 ESC

35A ESC running AM32 firmware, capable of up to 6S

10V/2.5A BEC for DJI O3 Air Unit

Digital VTX port 

Superhydrophobic Nano Coating




Specifications
FC

MCU: STM32G473

Gyro: ICM42688

Baro: DPS310

BEC: 5V/3A &amp 10V/2.5A

Blackbox: 128Mbit (16MB) Flash

OSD: AT7456

UART: 5 total

ESC

AM32 firmware with F4 MCU

Open Source firmware

Firmware upgradable via Betaflight passthrough (make sure your Betaflight
firmware is up to date when you try to use passthrough)

Article explaining AM32 by Oscar Liang

Input Voltage: 2S-6S

For input voltage below 4S, 10V BEC output cannot be used

For input voltage below 3S, both the 10V &amp 5V BEC output cannot be used

PWM Frequency 8k to 48k

Supports

DShot 150/300/600/1200

MultiShot/OneShot/Proshot/PWM etc.

ESC telemetry

Onboard analog current sensor

Metal MOSFETs for better heat dissipation
Mounting: 25 x 25mm/Φ3mm hole with Φ2mm Grommets

Dimension: 33x33mm

Weight: 7.5g

Includes

1x KAKUTE G4 AIO 35A
1x Capacitor 35V 470µF
2x 6 Pin SH1.0- 8 Pin GHR1.25 Cable (DJI VTx)
1x 6 Pin SH1.0 Cable
4x M2 Anti-Vibration Silicone Grommet Insert

Wiring Diagram


 


The Holybro Kakute G473 AIO packs a ton of features into a compact and powerful flight controller + 4in1 ESC board. It's plug-and-play compatible with the DJI O3 VTX. It also works with analog systems due to the onboard OSD chip. The FC on this AIO uses a G4 processor, and the 4in1 ESC uses four F4 processors running A

Holybro Kakute G4 2-6S AIO Whoop/Toothpick Flight Controller w/ F4 AM32 35A 32Bit 4in1 ESC

Holybro Kakute G4 2-6S AIO Whoop/Toothpick Flight Controller w/ F4 AM3














The Holybro Kakute G473 AIO packs a ton of features into a compact and powerful flight controller + 4in1 ESC board. It&#39s plug-and-play compatible with the DJI O3 VTX. It also works with analog systems due to the onboard OSD chip. The FC on this AIO uses a G4 processor, and the 4in1 ESC uses four F4 processors running AM32 firmware. Boasting an ICM-42688p gyro, 5V &ampamp 10V BEC, 16MB of flash storage &ampamp DSP310 baro. And with its super-hydrophobic, nano-waterproof coating, it weighs only 7.5g and provides protection from moisture and other elements.













Check out all our Whoop/AIO Flight Controllers, and the rest of our Holybro selection!
Features

AIO board with G4 Processor FC &ampamp F4 ESC

35A ESC running AM32 firmware, capable of up to 6S

10V/2.5A BEC for DJI O3 Air Unit

Digital VTX port 

Superhydrophobic Nano Coating




Specifications
FC

MCU: STM32G473

Gyro: ICM42688

Baro: DPS310

BEC: 5V/3A &ampamp 10V/2.5A

Blackbox: 128Mbit (16MB) Flash

OSD: AT7456

UART: 5 total

ESC

AM32 firmware with F4 MCU

Open Source firmware

Firmware upgradable via Betaflight passthrough (make sure your Betaflight
firmware is up to date when you try to use passthrough)

Article explaining AM32 by Oscar Liang

Input Voltage: 2S-6S

For input voltage below 4S, 10V BEC output cannot be used

For input voltage below 3S, both the 10V &ampamp 5V BEC output cannot be used

PWM Frequency 8k to 48k

Supports

DShot 150/300/600/1200

MultiShot/OneShot/Proshot/PWM etc.

ESC telemetry

Onboard analog current sensor

Metal MOSFETs for better heat dissipation
Mounting: 25 x 25mm/Φ3mm hole with Φ2mm Grommets

Dimension: 33x33mm

Weight: 7.5g

Includes

1x KAKUTE G4 AIO 35A
1x Capacitor 35V 470µF
2x 6 Pin SH1.0- 8 Pin GHR1.25 Cable (DJI VTx)
1x 6 Pin SH1.0 Cable
4x M2 Anti-Vibration Silicone Grommet Insert

Wiring Diagram


 


Holybro Kakute G4 2-6S AIO Whoop/Toothpick Flight Controller w/ F4 AM32 35A 32Bit 4in1 ESC from WREKD Co.

JHEMCU

JHEMCU F7 3-6S 30x30 Flight Controller Stack - GF30F745 FC, 32Bit 60A 4in1 ESC

FPVELITE

Meet your budget-friendly stack featuring an F7 FC on top of a 60A 32Bit ESC!
The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in port designed for HD VTXs like the DJI O3 Air Unit. 


























Experience the power of 32 bit performance with the JHEMCU BL32 4-in-1 ESC. This high-efficiency ESC accommodates 3-6S LiPo input and supports  60 amps. Get ready for smooth, rapid response and precise control.













Check out all our 30x30 stacks &amp combos, and the rest of our JHEMCU selection!















Specifications
FC

Chip: STM32F745VG(216MHZ)

Gyro: MPU6000

Barometer: DPS310

OSD Chip: AT7456E

Black box:16MM

LED Program: Support

BB buzzer: Support

Input voltage: 3-6S

I2C Connector: Support

BEC: 5V/2.5A

BEC: 10V/2.0A

Cam Input: Support

USART: UART1,UART2.UART3.UART4.UART6.UART7

Receiver: ELRS(CRSF).TBS(CRSF).SBUS.IBUS.DSM2.DSMX

GPS: YES

COMPASS: YES

HD O3: YES

ESC Signal: Dshoot150.Dshot300,Dshot600

USB: TYPE-C

Current Port: Yes.

Voltage Sensor: Yes

DFU Button: YES

FC firmware: betaflight_4.4.2_JHEF745.HEX

Instal hole: 30.5x30.5x4MM

Board size: 36x36MM

Weight: 7.5g

ESC

Input Power: 3-6S(11-27V)

Current: 60A

BEC: NO

Instal Hole: 30.5x30.5xM4

Size: 44x43MM

Firmware:BLHELI_32 JHEMCU_ESC32_MULTI_32_9.HEX

Weight: 15.4g

Includes

1x JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 60A 4in1 ESC) - Choose Version - MPU6000



Meet your budget-friendly stack featuring an F7 FC on top of a 60A 32Bit ESC! The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience wit

JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 60A 4in1 ESC) - MPU6000

JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 60A 4in1 ES

The JHEMCU GF30F745-MPU Flight Controller, combined with the BL32 60A 3-6S 4in1 ESC is a compact 30x30mm package providing reliable, high-performance Stack. Check out all our FPV Stacks Collection and the rest of our JHEMCU Products! Specifications: FC Chip:STM32F745VG(216MHZ) Gyro:MPU6000 Barometer:DPS310 OSD Chip:AT7

JHEMCU GF30F745-MPU Flight Controller with BL32 60A 3-6S 4in1 ESC Stack - 30x30mm

WREKD General

Meet your budget-friendly stack featuring an F7 FC on top of a 60A 32Bit ESC! The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in port designed for HD VTXs like the DJI O3 Air Unit.                            Experience the power of 32 bit performance with the JHEMCU BL32 4-in-1 ESC. This high-efficiency ESC accommodates 3-6S LiPo input and supports  60 amps. Get ready for smooth, rapid response and precise control.              Check out all our 30x30 stacks &ampamp combos, and the rest of our JHEMCU selection!                Specifications FC  Chip: STM32F745VG(216MHZ)  Gyro: MPU6000  Barometer: DPS310  OSD Chip: AT7456E  Black box:16MM  LED Program: Support  BB buzzer: Support  Input voltage: 3-6S  I2C Connector: Support  BEC: 5V/2.5A  BEC: 10V/2.0A  Cam Input: Support  USART: UART1,UART2.UART3.UART4.UART6.UART7  Receiver: ELRS(CRSF).TBS(CRSF).SBUS.IBUS.DSM2.DSMX  GPS: YES  COMPASS: YES  HD O3: YES  ESC Signal: Dshoot150.Dshot300,Dshot600  USB: TYPE-C  Current Port: Yes.  Voltage Sensor: Yes  DFU Button: YES  FC firmware: betaflight_4.4.2_JHEF745.HEX  Instal hole: 30.5x30.5x4MM  Board size: 36x36MM  Weight: 7.5g  ESC  Input Power: 3-6S(11-27V)  Current: 60A  BEC: NO  Instal Hole: 30.5x30.5xM4  Size: 44x43MM  Firmware:BLHELI_32 JHEMCU_ESC32_MULTI_32_9.HEX  Weight: 15.4g  Includes  1x JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 60A 4in1 ESC) - Choose Version - MPU6000  

JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 60A 4in1 ESC) - MPU6000 from WREKD Co.

JHEMCU F7 3-6S 30x30 Flight Controller Stack - GF30F745 FC, 32Bit 45A 4in1 ESC

Meet your budget-friendly stack featuring an F7 FC on top of a 45A 32Bit ESC! The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in port designed for HD VTXs like the DJI O3 Air Unit.                            Experience the power of 32 bit performance with the JHEMCU BL32 4-in-1 ESC. This high-efficiency ESC accommodates 3-6S LiPo input and supports  45 amps. Get ready for smooth, rapid response and precise control.              Check out all our 30x30 stacks &ampamp combos, and the rest of our JHEMCU selection!                Specifications FC  Chip: STM32F745VG(216MHZ)  Gyro: MPU6000  Barometer: DPS310  OSD Chip: AT7456E  Black box:16MM  LED Program: Support  BB buzzer: Support  Input voltage: 3-6S  I2C Connector: Support  BEC: 5V/2.5A  BEC: 10V/2.0A  Cam Input: Support  USART: UART1,UART2.UART3.UART4.UART6.UART7  Receiver: ELRS(CRSF).TBS(CRSF).SBUS.IBUS.DSM2.DSMX  GPS: YES  COMPASS: YES  HD O3: YES  ESC Signal: Dshoot150.Dshot300,Dshot600  USB: TYPE-C  Current Port: Yes.  Voltage Sensor: Yes  DFU Button: YES  FC firmware: betaflight_4.4.2_JHEF745.HEX  Instal hole: 30.5x30.5x4MM  Board size: 36x36MM  Weight: 7.5g  ESC  Input Power: 3-6S(11-27V)  Current: 45A  BEC: NO  Instal Hole: 30.5x30.5xM4  Size: 44x43MM  Firmware:BLHELI_32 JHEMCU_ESC32_MULTI_32_9.HEX  Weight: 15.4g  Includes  1x JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 45A 4in1 ESC) - Choose Version - MPU6000  

Meet your budget-friendly stack featuring an F7 FC on top of a 45A 32Bit ESC! The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience wit

JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 45A 4in1 ESC) - MPU6000 from WREKD Co.

JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 45A 4in1 ESC) - MPU6000

Meet your budget-friendly stack featuring an F7 FC on top of a 45A 32Bit ESC!
The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in port designed for HD VTXs like the DJI O3 Air Unit. 


























Experience the power of 32 bit performance with the JHEMCU BL32 4-in-1 ESC. This high-efficiency ESC accommodates 3-6S LiPo input and supports  45 amps. Get ready for smooth, rapid response and precise control.













Check out all our 30x30 stacks &amp combos, and the rest of our JHEMCU selection!















Specifications
FC

Chip: STM32F745VG(216MHZ)

Gyro: MPU6000

Barometer: DPS310

OSD Chip: AT7456E

Black box:16MM

LED Program: Support

BB buzzer: Support

Input voltage: 3-6S

I2C Connector: Support

BEC: 5V/2.5A

BEC: 10V/2.0A

Cam Input: Support

USART: UART1,UART2.UART3.UART4.UART6.UART7

Receiver: ELRS(CRSF).TBS(CRSF).SBUS.IBUS.DSM2.DSMX

GPS: YES

COMPASS: YES

HD O3: YES

ESC Signal: Dshoot150.Dshot300,Dshot600

USB: TYPE-C

Current Port: Yes.

Voltage Sensor: Yes

DFU Button: YES

FC firmware: betaflight_4.4.2_JHEF745.HEX

Instal hole: 30.5x30.5x4MM

Board size: 36x36MM

Weight: 7.5g

ESC

Input Power: 3-6S(11-27V)

Current: 45A

BEC: NO

Instal Hole: 30.5x30.5xM4

Size: 44x43MM

Firmware:BLHELI_32 JHEMCU_ESC32_MULTI_32_9.HEX

Weight: 15.4g

Includes

1x JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 45A 4in1 ESC) - Choose Version - MPU6000



JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 45A 4in1 ES

The JHEMCU GF30F745-MPU Flight Controller, combined with the BL32 45A 3-6S 4in1 ESC is a compact 30x30mm package providing reliable, high-performance Stack. Check out all our FPV Stacks Collection and the rest of our JHEMCU Products! Specifications: FC Chip:STM32F745VG(216MHZ) Gyro:MPU6000 Barometer:DPS310 OSD Chip:AT7

JHEMCU GF30F745-MPU Flight Controller with BL32 45A 3-6S 4in1 ESC Stack - 30x30mm

T-Motor

T-Motor VELOX Cine F7 Flight Controller Stack - 50A ESC

T-Motor Hobby

Unleash the true potential of your drone with the TMOTOR Velox CINE F7 Stack – the powerhouse combo of Velox CINE F7 FC and the robust V50A SE 4-in-1 ESC. Designed for those who understand that “average” just doesn’t cut it in the high-octane world of drone flight.
Performance That Leaves ‘Good Enough’ in the Dust: Dive into the specs, and you’ll see the ESC isn’t just smart, it’s ‘I-just-skipped-a-grade’ smart. With an F4 MCU flexing 50% more brainpower than its predecessor, it’s not just keeping up it’s setting the pace.
The flight controller is not one to be outdone. Equipped with an F7 MCU, it’s the tech equivalent of going from a brisk walk to a supersonic jet, boasting 30% more computing power than the F4.
Stability Meets Responsiveness: Our gyroscopes don’t mess around. High sampling rates? Check. A concoction of specialized optimization programs, whisper-quiet circuitry, and low noise design? Check, check, and check. Expect a flight experience so smooth, you’ll be forgiving of the occasional turbulence in life.
Upgrade your firmware to version 4.4.2 or better, and unlock the secret level of flight control. Think of it as the cheat code for unrivaled stability.
Endurance: Tested, Proven, Assured: 1,000 real flights with the Velox V3 motors and no glitches to report. That’s not just quality that’s ‘make-a-notebook-out-of-it’ level consistency.
Check out our other 30x30 Stacks &ampamp Combos and all our T-Motor products!


 
Specifications
VELOX CINE F7 Flight Controller

MCU: STM32F722

Input Voltage: 3-6S

Gyroscope: ICM-42688P

OSD: AT7456E&ampampHD

Barometer: SPL06

Mounting Holes: 30.5x30.5/Φ4mm

Size: 36x36x8mm

Weight: 9.2g

Firmware: TMTR-TMOTORVELOXF7V2 (BETAFLIGHT)


V50A SE ESC

MCU: AT32F421

Input Voltage: 3-6S

Current: 50A

Peak Current(5S): 60A

Size: 41x44.4x5.8mm

Mounting Holes: 30.5x30.5/Φ4mm
Weight: 12.3g

Includes

1x T-Motor CINE F7 FC+ V50A SE 3-6S 30x30 Stack/Combo (F722 FC / F4 32Bit 50A 4in1 ESC)


Unleash the true potential of your drone with the TMOTOR Velox CINE F7 Stack – the powerhouse combo of Velox CINE F7 FC and the robust V50A SE 4-in-1 ESC. Designed for those who understand that “average” just doesn’t cut it in the high-octane world of drone flight. Performance That Leaves ‘Good Enough’ in the Dust: Div

T-Motor CINE F7 FC + V50A SE 3-6S 30x30 Stack/Combo (F722 FC / 32Bit 50A F4 4in1 ESC) from WREKD Co.

T-Motor CINE F7 FC + V50A SE 3-6S 30x30 Stack/Combo (F722 FC / 32Bit 50A F4 4in1 ESC)

TMOTOR

Unleash the true potential of your drone with the TMOTOR Velox CINE F7 Stack – the powerhouse combo of Velox CINE F7 FC and the robust V50A SE 4-in-1 ESC. Designed for those who understand that “average” just doesn’t cut it in the high-octane world of drone flight.
Performance That Leaves ‘Good Enough’ in the Dust: Dive into the specs, and you’ll see the ESC isn’t just smart, it’s ‘I-just-skipped-a-grade’ smart. With an F4 MCU flexing 50% more brainpower than its predecessor, it’s not just keeping up it’s setting the pace.
The flight controller is not one to be outdone. Equipped with an F7 MCU, it’s the tech equivalent of going from a brisk walk to a supersonic jet, boasting 30% more computing power than the F4.
Stability Meets Responsiveness: Our gyroscopes don’t mess around. High sampling rates? Check. A concoction of specialized optimization programs, whisper-quiet circuitry, and low noise design? Check, check, and check. Expect a flight experience so smooth, you’ll be forgiving of the occasional turbulence in life.
Upgrade your firmware to version 4.4.2 or better, and unlock the secret level of flight control. Think of it as the cheat code for unrivaled stability.
Endurance: Tested, Proven, Assured: 1,000 real flights with the Velox V3 motors and no glitches to report. That’s not just quality that’s ‘make-a-notebook-out-of-it’ level consistency.
Check out our other 30x30 Stacks &amp Combos and all our T-Motor products!


 
Specifications
VELOX CINE F7 Flight Controller

MCU: STM32F722

Input Voltage: 3-6S

Gyroscope: ICM-42688P

OSD: AT7456E&ampHD

Barometer: SPL06

Mounting Holes: 30.5x30.5/Φ4mm

Size: 36x36x8mm

Weight: 9.2g

Firmware: TMTR-TMOTORVELOXF7V2 (BETAFLIGHT)


V50A SE ESC

MCU: AT32F421

Input Voltage: 3-6S

Current: 50A

Peak Current(5S): 60A

Size: 41x44.4x5.8mm

Mounting Holes: 30.5x30.5/Φ4mm
Weight: 12.3g

Includes

1x T-Motor CINE F7 FC+ V50A SE 3-6S 30x30 Stack/Combo (F722 FC / F4 32Bit 50A 4in1 ESC)


T-Motor CINE F7 FC + V50A SE 3-6S 30x30 Stack/Combo (F722 FC / 32Bit 5

The T-Motor Velox Cine F7 F722 Flight Controller &amp; Velox V50A SE 3-6S BLheli32 4in1 ESC STACK - 30x30mm provides an ideal combination of power, performance, and reliability for RC enthusiasts. This stack's 3-6S input supports up to 50A of total current, ensuring long-term durability and consistent results. Addition

T-Motor Velox Cine F7 F722 Flight Controller & Velox V50A SE 3-6S BLheli32 4in1 ESC STACK - 30x30mm

Diatone

Diatone Mamba MK5 G4 Alpha AIO Flight Controller - 40A 6S 32Bit ESC

DiatoneUSA

 Please notice：This AIO only supports Alpha and does not support BetaFlight
Alpha: https://gui.fettec.net/FC/index.html
Flight controllers that use Aphla are known to be the best for freestyling, for smoothness and reliability. Diatone is delivering on next-gen premium FPV parts, especially seen with the MK5 AIO. Capable of supporting up to 40 amps of power while working off metal mosfets, for better performance. You are going to want to put this on your next 3-4 inch freestyle ripper. 
Check out all our Whoop/AIO Flight Controllers and our full Diatone collection!
 Features

Metal Mosfets
Comes with a User Manual with a Wiring Diagram
PWM: 24~128K
HD Compatible 



Specification
FC Specifications


Target： Alpha


MCU: 170MHz STM32G473


GYRO: IIM-42652


OSD: Yes


Uarts: 4 Set


Motor Signal:4 Set


ESC Soft: Dshot300/600/1200/2400


Power Led: Yes


LED Controller: Yes


AIR UNIT Port: Yes


Buzz: Yes


Input: 4~6S Lipo (14.8~25.2V)


BEC Protection: Yes


Receiver Protection: Yes


TVS Protection: Yes


BEC: 10V 2A&ampamp 5V 2A


Mounting size: 25.5×25.5mm/M2


Overall dimensions: 35×34.5×6.5mm


ESC Specifications


Input: 4~6S Lipo (14.8~25.2V)f


Continue Current: 40A×4


Burst current: 45A (10S)


Target：BLHeli_32 MAMBA F40_128K


SOFT: Dshot300/600/1200/2400

PWM:24~128K

Includes

1x Diatone Mamba MK5 G4 4-6S AIO Whoop/Toothpick Flight Controller w/ 40A 32Bit 4in1 ESC - DSHOT2400 
1x High Frequency 470uF/35V

1x AIR UNIT sh1.0 connector

2x 16AWG 60mm

1x AMASS Original XT60



 Please notice：This AIO only supports Alpha and does not support BetaFlight Alpha: https://gui.fettec.net/FC/index.html Flight controllers that use Aphla are known to be the best for freestyling, for smoothness and reliability. Diatone is delivering on next-gen premium FPV parts, especially seen with the MK5 AIO. Capab

Diatone Mamba MK5 G4 4-6S AIO Whoop/Toothpick Flight Controller w/ 40A 32Bit 4in1 ESC - DSHOT2400 from WREKD Co.

Diatone Mamba MK5 G4 4-6S AIO Whoop/Toothpick Flight Controller w/ 40A 32Bit 4in1 ESC - DSHOT2400

DIATONE

 Please notice：This AIO only supports Alpha and does not support BetaFlight
Alpha: https://gui.fettec.net/FC/index.html
Flight controllers that use Aphla are known to be the best for freestyling, for smoothness and reliability. Diatone is delivering on next-gen premium FPV parts, especially seen with the MK5 AIO. Capable of supporting up to 40 amps of power while working off metal mosfets, for better performance. You are going to want to put this on your next 3-4 inch freestyle ripper. 
Check out all our Whoop/AIO Flight Controllers and our full Diatone collection!
 Features

Metal Mosfets
Comes with a User Manual with a Wiring Diagram
PWM: 24~128K
HD Compatible 



Specification
FC Specifications


Target： Alpha


MCU: 170MHz STM32G473


GYRO: IIM-42652


OSD: Yes


Uarts: 4 Set


Motor Signal:4 Set


ESC Soft: Dshot300/600/1200/2400


Power Led: Yes


LED Controller: Yes


AIR UNIT Port: Yes


Buzz: Yes


Input: 4~6S Lipo (14.8~25.2V)


BEC Protection: Yes


Receiver Protection: Yes


TVS Protection: Yes


BEC: 10V 2A&amp 5V 2A


Mounting size: 25.5×25.5mm/M2


Overall dimensions: 35×34.5×6.5mm


ESC Specifications


Input: 4~6S Lipo (14.8~25.2V)f


Continue Current: 40A×4


Burst current: 45A (10S)


Target：BLHeli_32 MAMBA F40_128K


SOFT: Dshot300/600/1200/2400

PWM:24~128K

Includes

1x Diatone Mamba MK5 G4 4-6S AIO Whoop/Toothpick Flight Controller w/ 40A 32Bit 4in1 ESC - DSHOT2400 
1x High Frequency 470uF/35V

1x AIR UNIT sh1.0 connector

2x 16AWG 60mm

1x AMASS Original XT60



Diatone Mamba MK5 G4 4-6S AIO Whoop/Toothpick Flight Controller w/ 40A

AxisFlying Argus PRO F7 3-6S 30x30 Flight Controller Stack - F722 FC, 65A 32Bit 4in1 ESC

AxisFlying

The Plug and Play Argus is AxisFlying electronic series that includes ESC, FC, and stack.  Argus PRO series adopt a full aluminum cover wrapped that can get IP54 to protect PCB.  Argus series is PCB electronic only. The FC is F722 which can support X8. If you want the best and for your build to look futuristic, this is the stack for you!
Check out all our 30x30 FC Stacks, and all our Axis Flying Products!

Specification
Argus PRO F722 Flight Controller

MCU: STM32F722RET6
Gyro: BMI270
Barometer: Yes
OSD: Yes
BEC: 9V/2A, 5V/2A
UART Ports: 6
Black Box: 16MB onboard
Number of supported motors: 8
Firmware Name: AXISFLYINGF7
Input Voltage: 3-6S LiPo 
Installation Holes: 30.5x30.5mm M3

32bit 4in1 ESC

Continuous Current: 65A
BLHeli_32 32bit
Burst Current: 75A
Size: 30.5x30.5mm M3
BEC: No
Weight: 32g
Input Voltage: 3-6S LiPo (12-30V Max)
ESC Target: BLHeli_32 (ST_G0_04)
Current Proportion Value: Scale = 400
PMW Frequency Range: 16-96khz
Telemetry: Supported
Ammeter: Supported
BEC: No
Installation Holes 30.5x30.5mm
Size: 48.6x46.6x8.7mm
Weight: 32g

Includes

1x AxisFlying Argus PRO F722 3-6S 30x30 Stack/Combo (F7 FC / 32bit 65A 4in1 ESC)
1x Wiring Set


The Plug and Play Argus is AxisFlying electronic series that includes ESC, FC, and stack.  Argus PRO series adopt a full aluminum cover wrapped that can get IP54 to protect PCB.  Argus series is PCB electronic only. The FC is F722 which can support X8. If you want the best and for your build to look futuristic, this is

AxisFlying Argus PRO F7 3-6S 30x30 Stack/Combo (F722 FC / 32Bit 65A 4in1 ESC) from WREKD Co.

AxisFlying Argus PRO F7 3-6S 30x30 Stack/Combo (F722 FC / 32Bit 65A 4in1 ESC)

AxisFlying Argus PRO F7 3-6S 30x30 Stack/Combo (F722 FC / 32Bit 65A 4i

HGLRC

HGLRC SPECTER F460 HD 2-6S 30x30 Flight Controller Stack - F405 V2 FC, 60A 8Bit 4in1 ESC

Check out this fantastic budget stack brought to you by HGLRC, which is 2S-6S capable and can confidently handle 60 amps of power. (70 Burst) Boasting an MP6000 for precise and reliable performance from your flight controller.  The SPECTER F460 is an excellent choice for your next 5-6&quot build! 

Check out our other 30x30 Stacks, and all our HGLRC products!
Features

The flight control adopts the extremely stable MPU6000 gyroscope

The flight control main control chip adopts F405 chip, and the serial port supports up to 4 groups, with fast operation speed and smoother control

The main chip of the ESC selects a new imported FD6288 processor, which is matched with ON3109 high-performance MOS, and can continuously withstand current and stabilize output

It can be quickly connected to the camera/receiver/image transmission/LED/GPS through the socket, no welding required

Maximum support for BEC 9V2A/BEC 5V2.5A, which can provide stable voltage and current output to external devices

Immersion gold high-tech design is temperature-resistant and current-resistant, the ESC has a large pad, and the flight controller is directly plugged in, so there is no trouble in welding

Integrated 16M black box, can record flight data

Onboard galvanometer module, real-time viewing of data such as current feedback through the flight control

 

Specifications

Input Voltage: 2-6S Lipo (7.4V-22.8V)

Installing Hole: 30.5x30.5mm, M3

Support Protocols :DShot600/300/150/Oneshot125/42,MultiShot

Weight:29g

SPECTER F405 FC

MCU: STM32F405

GYRO: MPU6000

OSD: AT7456E

Blackbox: 16MB

UART: 4

BEC: 9V2A/5V2.5A

FC Firmware: HGLRCF405V2

Size: 38mmx38mm

SPECTER 60A ESC

Constant Current: 60A

Peak Current: 70A（10s）

ESC Firmware: BL_S (J-H-30)

Size: 37x42.7mm

Includes

1x HGLRC SPECTER F460 HD 2-6S 30x30 Stack/Combo (F4 FC / 8Bit 60A 4in1 ESC) - MPU6000



Check out this fantastic budget stack brought to you by HGLRC, which is 2S-6S capable and can confidently handle 60 amps of power. (70 Burst) Boasting an MP6000 for precise and reliable performance from your flight controller.  The SPECTER F460 is an excellent choice for your next 5-6" build!  Check out our other 30x30

HGLRC SPECTER F460 HD 2-6S 30x30 Stack/Combo (F405 V2 FC  / 8Bit 60A 4in1 ESC) - MPU6000 from WREKD Co.

HGLRC SPECTER F460 HD 2-6S 30x30 Stack/Combo (F405 V2 FC  / 8Bit 60A 4in1 ESC) - MPU6000

Check out this fantastic budget stack brought to you by HGLRC, which is 2S-6S capable and can confidently handle 60 amps of power. (70 Burst) Boasting an MP6000 for precise and reliable performance from your flight controller.  The SPECTER F460 is an excellent choice for your next 5-6" build! 

Check out our other 30x30 Stacks, and all our HGLRC products!
Features

The flight control adopts the extremely stable MPU6000 gyroscope

The flight control main control chip adopts F405 chip, and the serial port supports up to 4 groups, with fast operation speed and smoother control

The main chip of the ESC selects a new imported FD6288 processor, which is matched with ON3109 high-performance MOS, and can continuously withstand current and stabilize output

It can be quickly connected to the camera/receiver/image transmission/LED/GPS through the socket, no welding required

Maximum support for BEC 9V2A/BEC 5V2.5A, which can provide stable voltage and current output to external devices

Immersion gold high-tech design is temperature-resistant and current-resistant, the ESC has a large pad, and the flight controller is directly plugged in, so there is no trouble in welding

Integrated 16M black box, can record flight data

Onboard galvanometer module, real-time viewing of data such as current feedback through the flight control

 

Specifications

Input Voltage: 2-6S Lipo (7.4V-22.8V)

Installing Hole: 30.5x30.5mm, M3

Support Protocols :DShot600/300/150/Oneshot125/42,MultiShot

Weight:29g

SPECTER F405 FC

MCU: STM32F405

GYRO: MPU6000

OSD: AT7456E

Blackbox: 16MB

UART: 4

BEC: 9V2A/5V2.5A

FC Firmware: HGLRCF405V2

Size: 38mmx38mm

SPECTER 60A ESC

Constant Current: 60A

Peak Current: 70A（10s）

ESC Firmware: BL_S (J-H-30)

Size: 37x42.7mm

Includes

1x HGLRC SPECTER F460 HD 2-6S 30x30 Stack/Combo (F4 FC / 8Bit 60A 4in1 ESC) - MPU6000



HGLRC SPECTER F460 HD 2-6S 30x30 Stack/Combo (F405 V2 FC / 8Bit 60A 4i

ESC Stack Mount

The ESC(s) controls your motors’ speed. It draws power from the battery to spin the motors based on what the FC tells it to do. Each motor needs an ESC. It’s common today to see 4-in-1 ESCs so you only need to buy a single part. For beginners, choose a 4-in-1 ESC that has a compatible mount with your frame and FC. The biggest consideration is amperage limit. We show you ESCs with appropriate amperage limits based on your frame size. You can calculate how much amperage you need based on your motor and prop choice. 

ESCs

Frame Stack Mount

The frame is typically the first part to pick because it determines what kind of flying you’ll be doing the most. Start by picking a frame type, and narrow down the options by propeller size. The frame holds your quad parts together and heavily impacts what the quad can do. 

Frames

The VTX processes the image from your FPV camera and sends it to your goggle’s video receiver (VRX). If you chose as digital video system, you need a VTX that matches the system. Most analog VTXs and VRXs are compatible with each other, and your biggest consideration will be how much output power you need. The more output power, the more range and better signal you’ll get. Learn more about VTXs.