FPV Quad Parts

Peripherals and Replacement Parts

Equipment

Equipment Peripherals

Build Page Parts

Build Parts Equipment

Pre-Built Quads and Kits 

Build Page Parts Overflow

Build Parts Equipment Overflow

Compatibility Categories

Continuous Amp Rating

HolyBro

Holybro Kakute H7 V1.3 4-6S 30x30 Flight Controller Stack -H7 FC, 50A F4 32bit 4in1 ESC

HOLYBRO

The Holybro Kakute H7 has integrated Bluetooth, dual 4in1 ESC ports, HD camera plug, barometer, OSD, 6 UARTs, MicroSD card, 5V &amp 9V BEC, easy soldering layout, etc. Supporting DJI HD, its 9V regulator powers FPV Air Unit &amp Caddx Vista. With 6 UART ports &amp inversion, it offers unlimited Blackbox data logging. BetaFlight OSD displays info on FPV display, and barometer helps autonomous flight. LED &amp buzzer pad, I2C pad for external GPS/Magnetometer.
Check out all our 30x30 Stacks and the rest of our HolyBro selection!


Features

This V1.3 now has USB-C, 9V 3A BEC for VTX, and JST-SH connector for VTX port.

Specifications for HolyBro Kakute H7 V1.3 FC


MCU - STM32H743 32-bit processor running at 480 MHz
IMU - MPU6000
Barometer - BMP280
OSD - AT7456E

Onboard Bluetooth chip - ESP32-C3

SpeedyBee IOS &amp Android App Compatible 
Note: The Bluetooth onboard is set to automatically turn off when the flight controller is unlocked (arm) and turn on automatically when the flight controller is locked (disarm).


6x UARTs (1,2,3,4,6,7 UART2 is used for Bluetooth telemetry)
9x PWM Outputs (8 Motor Output, 1 LED)
2x JST-SH1.0 8pin ESC port (4in1 ESCs, x8/Octocopter compatible)
1x JST-SH1.0 6pin VTX port (For HD System like Caddx Vista &amp Air Unit)
Battery input voltage: 7V to 42V
BEC 5V 2A Cont.
BEC 9V 3A Cont 
USB Type-C
Mounting - 30.5 x 30.5mm/Φ4mm hole with Φ3mm Grommets
Dimension - 35x35mm
Weight - 8g

Specifications for Tekko32 F4 4in1 50A ESC


Continuous Current: 50A x4
Burst Current: 60A x4
Supports 4-6S battery
Supports DShot 150/300/600/1200 &amp MultiShot/OneShot/Proshot/PWM etc.
ESC telemetry Supported
Onboard analog current sensor
No output BEC
BLHeli_32 firmware
1000uf 35v capacitor included (highly recommended for 6s setup)
Amperage meter scale ratio: 120 (V1.9 Version)
Dimensions: 48x37x6mm / Weight: 13.8g
Mounting holes: M4 30.5x30.5mm (M3 grommets included)

Firmware Targets

BetaFlight: KakuteH7 (v4.2.11 and above)

INAV: KakuteH7 (4.0.0 &amp above) SD card support added in 4.1.0.

ArduPilot: KakuteH7 (4.2.0 &amp above)


Includes

Holybro Kakute H7 V1.3 Tekko32 F4 50A 4-6S 30x30 Stack/Combo (H7 FC / 50A F4 32bit 4in1 ESC)
1x Wiring Kit

Wiring Diagram



The Holybro Kakute H7 has integrated Bluetooth, dual 4in1 ESC ports, HD camera plug, barometer, OSD, 6 UARTs, MicroSD card, 5V &amp; 9V BEC, easy soldering layout, etc. Supporting DJI HD, its 9V regulator powers FPV Air Unit &amp; Caddx Vista. With 6 UART ports &amp; inversion, it offers unlimited Blackbox data logging

Holybro Kakute H7 V1.3 Tekko32 F4 50A 4-6S 30x30 Stack/Combo (H7 FC / 50A F4 32bit 4in1 ESC)

Holybro Kakute H7 V1.3 Tekko32 F4 50A 4-6S 30x30 Stack/Combo (H7 FC / 

Holybro Kakute H7 V1.3 Tekko32 F4 50A 4-6S 30x30 Stack/Combo (H7 FC / 50A F4 32bit 4in1 ESC) from WREKD Co.

The version that is being ship at the moment is Kakute H7 V1.3. This V1.3 now has USB-C, 9V 3A BEC for VTX, and JST-SH connector for VTX port. For details on the difference between versions, please see this chart. The Holybro Kakute H7 v1 Flight Controller is full of features including integrated Bluetooth, dual plug-a

Holybro Kakute H7 v1.3 HD Bluetooth W/Tekko32 F4 4in1 50A ESC STACK - 30x30mm

Processor (MCU)

The FC is the brain or the CPU of your quad. It has a processor and other components that allow it to listen to your inputs and tells the quad what to do. FCs are commonly sold together with other components integrated or stacked (like ESCs and video transmitters). For beginners, choose a FC with a F4 or F7 processor that has a compatible mount with your frame. 

Flight Controllers

FC Stack Mount

Built-in VTX

Built-in ESC

Happymodel

HappyModel SuperF405HD 2-4S F4 AIO Flight Controller - 20A 8Bit 4in1 ESC,  2.4GHz ELRS RX

The Super F405HD ELRS AIO flight controller comes with integrated UART 2.4GHz ExpressLRS receiver and 20A Blheli_s ESC(Bluejay firmware pre-installed) which could support 2-4s battery. Bigger Mosfet could support high to 20A currents and reserved 6 pin socket for DJI HD equipment plug and play. It’s a great solution of build 2-4S HD digital FPV whoop.
Check out our other whoop flight controllers, and the rest of our Happymodel offerings.

Features


Integrated UART 2.4GHz ExpressLRS receiver and
20A Blheli_s ESC(Bluejay firmware pre-installed)
Big Mosfets that support high 20A currents
Great for 2-4S toothpick
Reserved 6 pin socket for DJI HD equipment plug &amp play.


Specifications

Flight Controller

MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
GYRO Sensor: ICM42688 (SPI connection)
Mount hole size: 25mm*25mm
Power supply: 2~4S battery input (DC 8.7V-17.4V)
Built-in 20A(each) Blheli_S 4in1 ESC
Built-in Serial ExpressLRS 2.4G (Default connected to UART2)
Built-in BMP280 Barometer
Built-in 8MBp blackbox
Built-in voltage meter sensor , voltage meter scale 110
Built-in current meter sensor , current meter scale 470
Flight controller firmware target: BETAFLIGHTF4

4in1 ESC (MCU upgraded to EFM8BB21)

Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Currents: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: Bluejay 0.19.2
Firmware target: F_H_40_48_v0.19.2
Default protocol: DSHOT150/DSHOT300/DSHOT600

UART ExpressLRS 2.4GHz Receiver 

Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna plug: IPEX
Telemetry output Power: &lt12dBm
Receiver protocol: CRSF
Default firmware version: ExpressLRS V3.0.1

Onboard voltage and Amperage meters settings 

Voltage meter scale setting 110
Amperage meter scale setting 470

 
Includes

1x HappyModel SuperF405HD 2-4S F4 AIO Toothpick/Whoop Flight Controller (w/ 20A 8Bit 4in1 ESC &amp 2.4GHz ELRS RX)
1x XT30 Pigtail
1x ELRS T Antenna
4x Rubber Grommets
4x Motor Plugs

 
Wiring


Binding
Binding procedure:

Supply power to the flight controller by plug USB, wait until the red LED on the FC is off, immediately turn off the power, and then repeat again the above steps. When the FC is powered on for the third time, the red LED light will start to double-flash, which means that the Receiver enters the binding mode
Please make sure your ExpressLRS tx module firmware is v3.x.x. And go to ExpressLRS.lua from “TOOLS” menu of your radio transmitter. Then hit [Bind] to binding with the onboard ExpressLRS receiver. The red LED should blinking slowly first then turn to solid, that means binding was successfully. If the red led keep tri-flash after binding ,please change Model Match tab value from “off” to “on” or from “on” to “off”

Receiver LED status meanings:
Red LED solid means bind successful or RC link established Red LED double-flash means get into bind mode Red LED flash slowly means no RC signal input from TX module Red LED continuous flash fast means ExpressLRS wifi enabled Red LED tri-flash means model mismatch need to change model match from “off” to “on”.
UART description:ELRS receiver was connected to UART2 default out of factory.Usually UART1 or UART6 Could be used for MSP OSD with HD VTX.UART6 could be used for GPS or other serial equipment.IRX6 is an inverted serial RX6 for SBUS input.IRX6 and TX6/RX6 couldn’t be used at the same time.

The Super F405HD ELRS AIO flight controller comes with integrated UART 2.4GHz ExpressLRS receiver and 20A Blheli_s ESC(Bluejay firmware pre-installed) which could support 2-4s battery. Bigger Mosfet could support high to 20A currents and reserved 6 pin socket for DJI HD equipment plug and play. It’s a great solution of

HappyModel SuperF405HD 2-4S F4 AIO Toothpick/Whoop Flight Controller (w/ 20A 8Bit 4in1 ESC & 2.4GHz ELRS RX) from WREKD Co.

HappyModel SuperF405HD 2-4S F4 AIO Toothpick/Whoop Flight Controller (w/ 20A 8Bit 4in1 ESC & 2.4GHz ELRS RX)

Happymodel SuperF405 HD AIO Flight Controller for HD Whoops 2-4S 20A ESC-UART ELRS 2.4GHz- 25x25mm

HAPPYMODEL

The world’s first AIO 5in1 F4 flight controller with integrated SPI 2.4GHz ExpressLRS receiver has been launched. The flight controller integrates SPI controlled 2.4GHz ExpressLRS receiver, Dshot protocol 4-in-1 ESC, 5.8GHz 40ch video transmitter and Betaflight OSD. Ultra-small size and ultra-stable remote control range can improve the range of the original SPI receiver. And because the 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate and low latency, this flight controller is the one that all Race/Freestyle pilots needed. It is suitable for use in Tiny whoop Race or Toothpick Freestyle, and can also be used in 1S ultra-lightweight Nano Long Range platform.

HappyModel ELRS 2G4 Whoop Flight Controller - For Sale At RaceDayQuads

HappyModel CruxF405HD 2-4S F4 20x20 AIO Flight Controller - 20A 8Bit 4in1 ESC, 2.4GHz ELRS RX

The CruxF405HD ELRS AIO flight controller comes with integrated UART 2.4GHz ExpressLRS receiver and 20A Blheli_s ESC(Bluejay firmware pre-installed) which could support 2-4s battery. Bigger Mosfet could support high to 20A currents would be better for 2-4S toothpick drone or long range FPV drone. Reserved 6 pin socket for DJI HD equipment plug and play. It’s a great solution of build HD digital FPV drone .
Check out our other AIO flight controllers, and the rest of our Happymodel offerings.

NOTES: If upgrade firmware to betaflight 4.4.x , need to add custom Defines “GYRO_SPI_ICM42688P ACC_SPI_ICM42688P” from build configuration of Betaflight configurator otherwise gyro may not be recognized. 
Features


Integrated UART 2.4GHz ExpressLRS receiver and 
20A Blheli_s ESC(Bluejay firmware pre-installed) 
Big Mosfets that support high 20A currents
Great for 2-4S toothpick
Reserved 6 pin socket for DJI HD equipment plug &amp play.

 
Specifications

Flight controller 

MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
GYRO Sensor: ICM42688 (SPI connection)
Mount hole size: 20mm*20mm
Power supply: 2~4S battery input (DC 8.7V-17.4V)
Built-in 20A(each) Blheli_S 4in1 ESC
Built-in Serial ExpressLRS 2.4G (Default connected to UART2)
Built-in BMP280 Barometer
Built-in 8MBp blackbox
Built-in voltage meter sensor , voltage meter scale 110
Built-in current meter sensor , current meter scale 470
Flight controller firmware target: BETAFLIGHTF4

4in1 ESC (MCU upgraded to EFM8BB21)

Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Currents: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: Bluejay 0.19.2
Firmware target: F_H_40_48_v0.19.2
Default protocol: DSHOT150/DSHOT300/DSHOT600

UART ExpressLRS 2.4GHz 

Receiver Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHz
Antenna plug: IPEX
Telemetry output Power: &lt12dBm
Receiver protocol: CRSF
Default firmware version: ExpressLRS V3.0.1

Voltage and Amperage meters settings 

Voltage meter scale setting 110
Amperage meter scale setting 470

Includes

1x HappyModel CruxF405HD 2-4S F4 AIO 20x20 Flight Controller (w/ 20A 8Bit 4in1 ESC &amp 2.4GHz ELRS RX)
1x XT30 Pigtail
1x ELRS T Antenna
4x Rubber Grommets
4x Motor Plugs


Binding
Binding procedure:

Supply power to the flight controller by plug USB, wait until the red LED on the FC is off, immediately turn off the power, and then repeat again the above steps. When the FC is powered on for the third time, the red LED light will start to double-flash, which means that the Receiver enters the binding mode
Please make sure your ExpressLRS tx module firmware is v3.x.x. And go to ExpressLRS.lua from “TOOLS” menu of your radio transmitter. Then hit [Bind] to binding with the onboard ExpressLRS receiver. The red LED should blinking slowly first then turn to solid, that means binding was successfully. If the red led keep tri-flash after binding ,please change Model Match tab value from “off” to “on” or from “on” to “off”

Receiver LED status meanings:
Red LED solid means bind successful or RC link established Red LED double-flash means get into bind mode Red LED flash slowly means no RC signal input from TX module Red LED continuous flash fast means ExpressLRS wifi enabled Red LED tri-flash means model mismatch need to change model match from “off” to “on”.
UART description:ELRS receiver was connected to UART2 default out of factory.Usually UART1 or UART6 Could be used for MSP OSD with HD VTX.UART6 could be used for GPS or other serial equipment.IRX6 is an inverted serial RX6 for SBUS input.IRX6 and TX6/RX6 couldn’t be used at the same time.

The CruxF405HD ELRS AIO flight controller comes with integrated UART 2.4GHz ExpressLRS receiver and 20A Blheli_s ESC(Bluejay firmware pre-installed) which could support 2-4s battery. Bigger Mosfet could support high to 20A currents would be better for 2-4S toothpick drone or long range FPV drone. Reserved 6 pin socket 

HappyModel CruxF405HD 2-4S F4 AIO 20x20 Flight Controller (w/ 20A 8Bit 4in1 ESC & 2.4GHz ELRS RX) from WREKD Co.

HappyModel CruxF405HD 2-4S F4 AIO 20x20 Flight Controller (w/ 20A 8Bit 4in1 ESC & 2.4GHz ELRS RX)

Happymodel CruxF405 HD AIO Flight Controller 2-4S 20A ESC-UART ELRS 2.4GHz- 20x20mm

GEPRC

GEPRC TAKER G4 35A AIO Flight Controller - 35A ESC

TAKER G4 35A is a newly developed AIO flight control by the GEPRC team. It adopts G473 main control and has more redundant computing power. In response to market demand, the TYPE-C interface has been upgraded, and the power supply pad and motor wire pad have been optimized to make welding easier. It is compatible with 

GEPRC TAKER G4 35A AIO Flight Controller and 2-4S 35A ESC - 25x25mm

Summary
TAKER G4 35A is a newly developed AIO flight control by the GEPRC team. It adopts G473 main control and has more redundant computing power.

In response to market demand, the TYPE-C interface has been upgraded, and the power supply pad and motor wire pad have been optimized to make welding easier. It is compatible with two mounting holes of 25.5-26.5mm and can be compatible with more frames.

We are committed to pursuing flight controllers that are smaller in size, lighter in weight and stronger in performance.
Feature

 	Compact size and compatible mounting holes make installation convenient.
 	 Light weight only 7.7g.
 	G473 main control, 170MHz operating frequency, abundant computing power.
 	 Upgraded Type-c USB for better versatility.

Specifications

 	Model Name：TAKER G4 35A AIO
 	MCU：STM32G473CEU6
 	IMU：ICM 42688-P
 	Firmware target：TAKERG4AIO
 	OSD：Betaflight OSD w/ AT7456Ev
 	Uart：R1 T1 / R2 T2 / R4 T4 / R5 T5
 	Buzzer：YES
 	LED ：YES
 	USB ：Type-c USB
 	BEC output：5V@3A
 	ESC MCU：BB21F16G
 	Continuous Current：35A
 	Burst Current：45A(5″)
 	lnput Voltage：2~4S (LIPO Battery)
 	Supports：Dshot600,Oneshot,Multishot
 	Current meter: YES
 	target：J -H -15
 	Size：33.4x34.4mm Board
 	Install hole：25.5-26.5 Φ3.05mm
 	Weight：7.7g

Includes
1 x GEP-TAKER G4 35A AIO

1 x Cable Set

Summary TAKER G4 35A is a newly developed AIO flight control by the GEPRC team. It adopts G473 main control and has more redundant computing power. In response to market demand, the TYPE-C interface has been upgraded, and the power supply pad and motor wire pad have been optimized to make welding easier. It is [...]

GEP-TAKER G4 35A AIO - GEPRC

GEP-TAKER G4 35A AIO

iFlight

iFlight Blitz ATF435 E55S 2-6S 30x30 Flight Controller Stack - ATF435 FC, 55A 32bit 4in1 ESC

Please note, this Flight Controller is based on the ATF435 chip opposed the the F4's and F7's most of the community is used to.  Downloading new drivers and using custom targets may be required. As long as your BetaFlight 10.10 you should be good to go! The iFlight Blitz ATF435 Stack/Combo provides dependable performan

iFlight Blitz ATF435 E55S 2-6S Stack/Combo (ATF435 FC/ 55A 8Bit 4in1 ESC) - 30x30

IFLIGHT












The iFlight Blitz ATF435 Stack/Combo provides dependable performance and efficient control of your 2-6S powered quadcopter. This 30x30 stack/combo features an ATF435 FC and 55A 8Bit 4in1 ESC to give you responsive controls and reliable power delivery. Fly worry-free and explore new heights. This flight controller comes with plug-in ports for 9V VTXs, LED/Buzzer, receiver, camera, &amp the ESC. The NEW ATF processors allow for a product like this, a 60-dollar stack that is feature-rich and comes with a 55Amp ESC, which is perfect for those amp-hungry builds. 











Check out our other 30x30 Stacks &amp Combos as well as our entire iFlight selection!
To configure download ATBetaflight and if that does not automatically connect, here are virtual com port drivers.  Future versions of Betaflight will fully support these boards.

Specifications

iFlight Blitz ATF435

MCU: AT32F435CGU7

Gyro: BMI270

Barometer: DPS310

OSD Chip: AT7456E

Flash: 32MB (Blackbox flash)
UARTS: 6

Motor outputs: 4x (SH1.0 connector)

I2C serial: SDA / SLA pads

Smartaudio / IRC Tramp VTX protocol supported

LED controller: Yes

Beeper pad: Yes

Firmware target: IFLIGHT_BLITZ_ATF435

Mount pattern: 30.5x30.5mm / 4mm PCB hole diameter

Dimensions: 36.5x35 mm

Weight: 7.8g

BEC: 5V 2.5A / 9V 2A

Blitz E55S ESC

Mounting Holes: 30.5x30.5mm/Φ4mm

Weight: 14.7g

Supports 2-6S lipo input

MCU: G071

Constant: 55 Amps 

Burst: 65 Amp

Current sensor: Yes

BEC: No

Current rate: 200

Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.

Target: Q-H-25 16.7(BlheliS) / Bluejay Q-H-50 (Bluejay)


Include

1x iFlight Blitz ATF435 E55S 2-6S 30x30 Stack/Combo (ATF435 FC/ 55A 8Bit 4in1 ESC)


The iFlight Blitz ATF435 Stack/Combo provides dependable performance and efficient control of your 2-6S powered quadcopter. This 30x30 stack/combo features an ATF435 FC and 55A 8Bit 4in1 ESC to give you responsive controls and reliable power delivery. Fly worry-free and explore new heights. This flight controller comes

iFlight Blitz ATF435 E55S 2-6S 30x30 Stack/Combo (ATF435 FC/ 55A 8Bit 4in1 ESC)

iFlight Blitz ATF435 E55S 2-6S 30x30 Stack/Combo (ATF435 FC/ 55A 8Bit 

RaceDayQuads












The iFlight Blitz ATF435 Stack/Combo provides dependable performance and efficient control of your 2-6S powered quadcopter. This 30x30 stack/combo features an ATF435 FC and 55A 8Bit 4in1 ESC to give you responsive controls and reliable power delivery. Fly worry-free and explore new heights. This flight controller comes with plug-in ports for 9V VTXs, LED/Buzzer, receiver, camera, &amp the ESC. The NEW ATF processors allow for a product like this, a 60-dollar stack that is feature-rich and comes with a 55Amp ESC, which is perfect for those amp-hungry builds. 











To configure download ATBetaflight and if that does not automatically connect, here are virtual com port drivers.  Future versions of Betaflight will fully support these boards.

Specifications

iFlight Blitz ATF435

MCU: AT32F435CGU7

Gyro: BMI270

Barometer: DPS310

OSD Chip: AT7456E

Flash: 32MB (Blackbox flash)
UARTS: 6

Motor outputs: 4x (SH1.0 connector)

I2C serial: SDA / SLA pads

Smartaudio / IRC Tramp VTX protocol supported

LED controller: Yes

Beeper pad: Yes

Firmware target: IFLIGHT_BLITZ_ATF435

Mount pattern: 30.5x30.5mm / 4mm PCB hole diameter

Dimensions: 36.5x35 mm

Weight: 7.8g

BEC: 5V 2.5A / 9V 2A

Blitz E55S ESC

Mounting Holes: 30.5x30.5mm/Φ4mm

Weight: 14.7g

Supports 2-6S lipo input

MCU: G071

Constant: 55 Amps 

Burst: 65 Amp

Current sensor: Yes

BEC: No

Current rate: 200

Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.

Target: Q-H-25 16.7(BlheliS) / Bluejay Q-H-50 (Bluejay)


Include

1x iFlight Blitz ATF435 E55S 2-6S 30x30 Stack/Combo (ATF435 FC/ 55A 8Bit 4in1 ESC)













Please note, this Flight Controller is based on the ATF435 chip opposed the the F4's and F7's most of the community is used to.  Downloading new drivers and using custom targets may be required.
As long as your BetaFlight 10.10 you should be good to go!
The iFlight Blitz ATF435 Stack/Combo provides dependable performance and efficient control of your 2-6S powered quadcopter. This 30x30 stack/combo features an ATF435 FC and 55A 8Bit 4in1 ESC to give you responsive controls and reliable power delivery. Fly worry-free and explore new heights. This flight controller comes with plug-in ports for 9V VTXs, LED/Buzzer, receiver, camera, &amp the ESC. The NEW ATF processors allow for a product like this, a 60-dollar stack that is feature-rich and comes with a 55Amp ESC, which is perfect for those amp-hungry builds. 











Check out our other 30x30 Stacks &amp Combos as well as our entire iFlight selection!
To configure download ATBetaflight and if that does not automatically connect, here are virtual com port drivers.  Future versions of Betaflight will fully support these boards.

Specifications

iFlight Blitz ATF435

MCU: AT32F435CGU7

Gyro: BMI270

Barometer: DPS310

OSD Chip: AT7456E

Flash: 32MB (Blackbox flash)
UARTS: 6

Motor outputs: 4x (SH1.0 connector)

I2C serial: SDA / SLA pads

Smartaudio / IRC Tramp VTX protocol supported

LED controller: Yes

Beeper pad: Yes

Firmware target: IFLIGHT_BLITZ_ATF435

Mount pattern: 30.5x30.5mm / 4mm PCB hole diameter

Dimensions: 36.5x35 mm

Weight: 7.8g

BEC: 5V 2.5A / 9V 2A

Blitz E55S ESC

Mounting Holes: 30.5x30.5mm/Φ4mm

Weight: 14.7g

Supports 2-6S lipo input

MCU: G071

Constant: 55 Amps 

Burst: 65 Amp

Current sensor: Yes

BEC: No

Current rate: 200

Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.

Target: Q-H-25 16.7(BlheliS) / Bluejay Q-H-50 (Bluejay)


Include

1x iFlight Blitz ATF435 E55S 2-6S 30x30 Stack/Combo (ATF435 FC/ 55A 8Bit 4in1 ESC)


iFlight Blitz ATF435 E55S 2-6S 30x30 Stack/Combo (ATF435 FC/ 55A 8Bit 4in1 ESC) from WREKD Co.

T-Motor

T-Motor VELOX Cine F7 Flight Controller Stack - 50A ESC

T-Motor Hobby

Unleash the true potential of your drone with the TMOTOR Velox CINE F7 Stack – the powerhouse combo of Velox CINE F7 FC and the robust V50A SE 4-in-1 ESC. Designed for those who understand that “average” just doesn’t cut it in the high-octane world of drone flight.
Performance That Leaves ‘Good Enough’ in the Dust: Dive into the specs, and you’ll see the ESC isn’t just smart, it’s ‘I-just-skipped-a-grade’ smart. With an F4 MCU flexing 50% more brainpower than its predecessor, it’s not just keeping up it’s setting the pace.
The flight controller is not one to be outdone. Equipped with an F7 MCU, it’s the tech equivalent of going from a brisk walk to a supersonic jet, boasting 30% more computing power than the F4.
Stability Meets Responsiveness: Our gyroscopes don’t mess around. High sampling rates? Check. A concoction of specialized optimization programs, whisper-quiet circuitry, and low noise design? Check, check, and check. Expect a flight experience so smooth, you’ll be forgiving of the occasional turbulence in life.
Upgrade your firmware to version 4.4.2 or better, and unlock the secret level of flight control. Think of it as the cheat code for unrivaled stability.
Endurance: Tested, Proven, Assured: 1,000 real flights with the Velox V3 motors and no glitches to report. That’s not just quality that’s ‘make-a-notebook-out-of-it’ level consistency.
Check out our other 30x30 Stacks &amp Combos and all our T-Motor products!


 
Specifications
VELOX CINE F7 Flight Controller

MCU: STM32F722

Input Voltage: 3-6S

Gyroscope: ICM-42688P

OSD: AT7456E&ampHD

Barometer: SPL06

Mounting Holes: 30.5x30.5/Φ4mm

Size: 36x36x8mm

Weight: 9.2g

Firmware: TMTR-TMOTORVELOXF7V2 (BETAFLIGHT)


V50A SE ESC

MCU: AT32F421

Input Voltage: 3-6S

Current: 50A

Peak Current(5S): 60A

Size: 41x44.4x5.8mm

Mounting Holes: 30.5x30.5/Φ4mm
Weight: 12.3g

Includes

1x T-Motor CINE F7 FC+ V50A SE 3-6S 30x30 Stack/Combo (F722 FC / F4 32Bit 50A 4in1 ESC)


Unleash the true potential of your drone with the TMOTOR Velox CINE F7 Stack – the powerhouse combo of Velox CINE F7 FC and the robust V50A SE 4-in-1 ESC. Designed for those who understand that “average” just doesn’t cut it in the high-octane world of drone flight. Performance That Leaves ‘Good Enough’ in the Dust: Div

T-Motor CINE F7 FC + V50A SE 3-6S 30x30 Stack/Combo (F722 FC / 32Bit 50A F4 4in1 ESC) from WREKD Co.

T-Motor CINE F7 FC + V50A SE 3-6S 30x30 Stack/Combo (F722 FC / 32Bit 50A F4 4in1 ESC)

The T-Motor Velox Cine F7 F722 Flight Controller &amp; Velox V50A SE 3-6S BLheli32 4in1 ESC STACK - 30x30mm provides an ideal combination of power, performance, and reliability for RC enthusiasts. This stack's 3-6S input supports up to 50A of total current, ensuring long-term durability and consistent results. Addition

T-Motor Velox Cine F7 F722 Flight Controller & Velox V50A SE 3-6S BLheli32 4in1 ESC STACK - 30x30mm

TMOTOR

T-Motor CINE F7 FC + V50A SE 3-6S 30x30 Stack/Combo (F722 FC / 32Bit 5

Tiger Motors

Introducing the T-Motor VELOX Stack, featuring the powerful combination of the Cine F7 flight controller and the V50A SE 6S BLHeli_32 4-in-1 ESC.

T-Motor VELOX Stack - Cine F7 FC + V50A SE 6S BLHeli_32 4-in-1 ESC

GEPRC TAKER F411 AIO Flight Controller - 12A ESC, ELRS 2.4GHz Receiver

Introducing the GEPRC Taker F411 8bit 12A AIO Flight Controller, the perfect addition to your mini FPV drone. It is packed with features like ICM-42688-P gyro, 12A ESC support, 2-4S power, and a built-in black box with 16MB flash memory for easy parameter adjustments. Best of all, this AIO comes with a built-in ELRS 2.4GHz receiver with a U.FL connector. Get ready for smooth and precise races and freestyles with this highly-integrated powerful all-in-one flight controller! 
Check out all our Whoop/AIO Flight Controllers, as well as the rest of our GEPRC selection.
Features

Bluejay 12A ESC, support 2-4S battery, continuous current 12A, peak current 13A, built-in ammeter
SPI ELRS 2.4G receiver 
Using STM32F411 FC, the flight control is running stably
Using IMU: ICM42688P gyroscope, 8K sampling rate
Support buzzer and LED light function
With 25.5mm x 25.5mm mounting holes 


Specifications 

Model: TAKER F411 8Bit 12A AIO  
MCU: STM32F411
IMU: ICM42688P
Firmware target: GEPRC_F411_SX1280
OSD: BetaFlight OSD w/ AT7456E chip
UART Ports: R1 T1\R2 T2
Reverse Port: NR2
Buzzer: YES
LED: YES
USB Port: Micro USB
ESC MCU: BB21F16G
Black Box: 16Mb onboard flash memory
Continuous Current: 12A
Peak Current: 13A
Input: 2-4S
ESC Protocol: Dshot300, Oneshot, Multishot
Current Meter: 210
ESC Firmware: G-H-30 – Bluejay, 0.16, 48kH
Size: 31.2 x 31.2mm Board
Mounting holes: 25.5mm x 25.5mm hole, M2 hole
Weight: 7g
ELRS Connector: U.FL

Includes 

1x GEPRC Taker F411 2-4S AIO Whoop/Toothpick w/12A 8bit 4in1 ESC - ELRS 2.4GHz (SPI)
1x XT30-5.5CM-20AWG power cable
8x M2x6.5mm FC damping grommets (4 each in red/black)
1x 35V220UF capacitor
5x Self-tapping screws (M1.4X5)
1x Instruction manual


Introducing the GEPRC Taker F411 8bit 12A AIO Flight Controller, the perfect addition to your mini FPV drone. It is packed with features like ICM-42688-P gyro, 12A ESC support, 2-4S power, and a built-in black box with 16MB flash memory for easy parameter adjustments. Best of all, this AIO comes with a built-in ELRS 2.

GEPRC Taker F411 2-4S AIO Whoop/Toothpick w/12A 8Bit 4in1 ESC - ELRS 2.4GHz (SPI)

GEPRC Taker F411 2-4S AIO Whoop/Toothpick w/12A 8Bit 4in1 ESC - ELRS 2

Brand new TAKER F411 8Bit 12A AIO adds new blood to the MINI FPV, the weight of the AIO integrated board is only 7 grams, making the small body lighter and improving the overall feel of the small FPV drones.  TAKER F411 8Bit 12A AIO adopts ICM-42688-P gyro, with precise and smooth touch, both racing and freestyle flyin

GEPRC TAKER F411 AIO Flight Controller Built-in ELRS 2.4G Receiver and 2-4S 12A Bluejay ESC - 25x25mm

Summary
TAKER F411-12A-E 1~2S AIO is a lightweight and highly integrated flight control system, weighing only 4.2g. It is suitable for 1.2-2-inch Whoop models or 3-inch toothpick models.

The 12A ESC overcurrent capability has sufficient redundancy on a small model, and the integrated ELRS2.4G 3.0 receiver makes the installation more space-saving and complete. The F411 main control is equipped with a BMI270 gyroscope, making the flight feel silky and stable.
Feature

 	 Highly integrated and lightweight flight system
 	 Supports 1-2S power supply and has higher battery compatibility
 	STM32F411 main control and BMI270 gyroscope solution, the flight feels silky and stable
 	 The motor wiring is reserved for welding or SH1
 	 Integrated ELRS2

Specifications

 	Model: TAKER F411-12A-E 1~2S AIO
 	MCU: STM32F411
 	IMU: BMI270
 	Firmware Target: TAKERF411
 	OSD: Betaflight OSD w/ AT7456Ev
 	UART: T1 R1 / T2 R2
 	SBUS: R2
 	Receiver: ELRS2.4G 3.0
 	Buzzer: Support
 	LED: Support
 	USB: Micro USB
 	ESC MCU: EFM8BB21F16G
 	Continuous Current: 12A
 	Burst Current: 13A
 	Input Voltage: LiPo/LiHv 1S-2S
 	Support Protocol: Dshot300/600,Oneshot,Multishot
 	Blackbox: 8MB
 	Galvanometer: Support
 	Firmware Target: C-X-30
 	Size: 30.5mm*30.5mm
 	Fixing hole size：25.5mm*25.5mm（M2）
 	Weight: 4.2g

Includes
1 x TAKER F411-12A-E 1~2S AIO

1 x Cable Set

Summary TAKER F411-12A-E 1~2S AIO is a lightweight and highly integrated flight control system, weighing only 4.2g. It is suitable for 1.2-2-inch Whoop models or 3-inch toothpick models. The 12A ESC overcurrent capability has sufficient redundancy on a small model, and the integrated ELRS2.4G 3.0 receiver makes the installation more space-saving and complete. The F411 [...]

GEP-TAKER F411-12A-E 1~2S AIO - GEPRC

GEP-TAKER F411-12A-E 1~2S AIO

GEPRC Taker F411 2-4S AIO Whoop/Toothpick w/12A 8Bit 4in1 ESC - ELRS 2.4GHz (SPI) from WREKD Co.

JHEMCU

JHEMCU F7 3-6S 30x30 Flight Controller Stack - GF30F745 FC, 32Bit 45A 4in1 ESC

FPVELITE

Meet your budget-friendly stack featuring an F7 FC on top of a 45A 32Bit ESC!
The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in port designed for HD VTXs like the DJI O3 Air Unit. 


























Experience the power of 32 bit performance with the JHEMCU BL32 4-in-1 ESC. This high-efficiency ESC accommodates 3-6S LiPo input and supports  45 amps. Get ready for smooth, rapid response and precise control.













Check out all our 30x30 stacks &amp combos, and the rest of our JHEMCU selection!















Specifications
FC

Chip: STM32F745VG(216MHZ)

Gyro: MPU6000

Barometer: DPS310

OSD Chip: AT7456E

Black box:16MM

LED Program: Support

BB buzzer: Support

Input voltage: 3-6S

I2C Connector: Support

BEC: 5V/2.5A

BEC: 10V/2.0A

Cam Input: Support

USART: UART1,UART2.UART3.UART4.UART6.UART7

Receiver: ELRS(CRSF).TBS(CRSF).SBUS.IBUS.DSM2.DSMX

GPS: YES

COMPASS: YES

HD O3: YES

ESC Signal: Dshoot150.Dshot300,Dshot600

USB: TYPE-C

Current Port: Yes.

Voltage Sensor: Yes

DFU Button: YES

FC firmware: betaflight_4.4.2_JHEF745.HEX

Instal hole: 30.5x30.5x4MM

Board size: 36x36MM

Weight: 7.5g

ESC

Input Power: 3-6S(11-27V)

Current: 45A

BEC: NO

Instal Hole: 30.5x30.5xM4

Size: 44x43MM

Firmware:BLHELI_32 JHEMCU_ESC32_MULTI_32_9.HEX

Weight: 15.4g

Includes

1x JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 45A 4in1 ESC) - Choose Version - MPU6000



Meet your budget-friendly stack featuring an F7 FC on top of a 45A 32Bit ESC! The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience wit

JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 45A 4in1 ESC) - MPU6000

JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 45A 4in1 ES

WREKD General

Meet your budget-friendly stack featuring an F7 FC on top of a 45A 32Bit ESC! The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in port designed for HD VTXs like the DJI O3 Air Unit.                            Experience the power of 32 bit performance with the JHEMCU BL32 4-in-1 ESC. This high-efficiency ESC accommodates 3-6S LiPo input and supports  45 amps. Get ready for smooth, rapid response and precise control.              Check out all our 30x30 stacks &amp combos, and the rest of our JHEMCU selection!                Specifications FC  Chip: STM32F745VG(216MHZ)  Gyro: MPU6000  Barometer: DPS310  OSD Chip: AT7456E  Black box:16MM  LED Program: Support  BB buzzer: Support  Input voltage: 3-6S  I2C Connector: Support  BEC: 5V/2.5A  BEC: 10V/2.0A  Cam Input: Support  USART: UART1,UART2.UART3.UART4.UART6.UART7  Receiver: ELRS(CRSF).TBS(CRSF).SBUS.IBUS.DSM2.DSMX  GPS: YES  COMPASS: YES  HD O3: YES  ESC Signal: Dshoot150.Dshot300,Dshot600  USB: TYPE-C  Current Port: Yes.  Voltage Sensor: Yes  DFU Button: YES  FC firmware: betaflight_4.4.2_JHEF745.HEX  Instal hole: 30.5x30.5x4MM  Board size: 36x36MM  Weight: 7.5g  ESC  Input Power: 3-6S(11-27V)  Current: 45A  BEC: NO  Instal Hole: 30.5x30.5xM4  Size: 44x43MM  Firmware:BLHELI_32 JHEMCU_ESC32_MULTI_32_9.HEX  Weight: 15.4g  Includes  1x JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 45A 4in1 ESC) - Choose Version - MPU6000  

JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 45A 4in1 ESC) - MPU6000 from WREKD Co.

The JHEMCU GF30F745-MPU Flight Controller, combined with the BL32 45A 3-6S 4in1 ESC is a compact 30x30mm package providing reliable, high-performance Stack. Check out all our FPV Stacks Collection and the rest of our JHEMCU Products! Specifications: FC Chip:STM32F745VG(216MHZ) Gyro:MPU6000 Barometer:DPS310 OSD Chip:AT7

JHEMCU GF30F745-MPU Flight Controller with BL32 45A 3-6S 4in1 ESC Stack - 30x30mm

JHEMCU F7 3-6S 30x30 Flight Controller Stack - GF30F745 FC, 32Bit 60A 4in1 ESC

The JHEMCU GF30F745-MPU Flight Controller, combined with the BL32 60A 3-6S 4in1 ESC is a compact 30x30mm package providing reliable, high-performance Stack. Check out all our FPV Stacks Collection and the rest of our JHEMCU Products! Specifications: FC Chip:STM32F745VG(216MHZ) Gyro:MPU6000 Barometer:DPS310 OSD Chip:AT7

JHEMCU GF30F745-MPU Flight Controller with BL32 60A 3-6S 4in1 ESC Stack - 30x30mm

Meet your budget-friendly stack featuring an F7 FC on top of a 60A 32Bit ESC! The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in port designed for HD VTXs like the DJI O3 Air Unit.                            Experience the power of 32 bit performance with the JHEMCU BL32 4-in-1 ESC. This high-efficiency ESC accommodates 3-6S LiPo input and supports  60 amps. Get ready for smooth, rapid response and precise control.              Check out all our 30x30 stacks &amp combos, and the rest of our JHEMCU selection!                Specifications FC  Chip: STM32F745VG(216MHZ)  Gyro: MPU6000  Barometer: DPS310  OSD Chip: AT7456E  Black box:16MM  LED Program: Support  BB buzzer: Support  Input voltage: 3-6S  I2C Connector: Support  BEC: 5V/2.5A  BEC: 10V/2.0A  Cam Input: Support  USART: UART1,UART2.UART3.UART4.UART6.UART7  Receiver: ELRS(CRSF).TBS(CRSF).SBUS.IBUS.DSM2.DSMX  GPS: YES  COMPASS: YES  HD O3: YES  ESC Signal: Dshoot150.Dshot300,Dshot600  USB: TYPE-C  Current Port: Yes.  Voltage Sensor: Yes  DFU Button: YES  FC firmware: betaflight_4.4.2_JHEF745.HEX  Instal hole: 30.5x30.5x4MM  Board size: 36x36MM  Weight: 7.5g  ESC  Input Power: 3-6S(11-27V)  Current: 60A  BEC: NO  Instal Hole: 30.5x30.5xM4  Size: 44x43MM  Firmware:BLHELI_32 JHEMCU_ESC32_MULTI_32_9.HEX  Weight: 15.4g  Includes  1x JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 60A 4in1 ESC) - Choose Version - MPU6000  

Meet your budget-friendly stack featuring an F7 FC on top of a 60A 32Bit ESC! The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience wit

JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 60A 4in1 ESC) - MPU6000 from WREKD Co.

JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 60A 4in1 ESC) - MPU6000

Meet your budget-friendly stack featuring an F7 FC on top of a 60A 32Bit ESC!
The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in port designed for HD VTXs like the DJI O3 Air Unit. 


























Experience the power of 32 bit performance with the JHEMCU BL32 4-in-1 ESC. This high-efficiency ESC accommodates 3-6S LiPo input and supports  60 amps. Get ready for smooth, rapid response and precise control.













Check out all our 30x30 stacks &amp combos, and the rest of our JHEMCU selection!















Specifications
FC

Chip: STM32F745VG(216MHZ)

Gyro: MPU6000

Barometer: DPS310

OSD Chip: AT7456E

Black box:16MM

LED Program: Support

BB buzzer: Support

Input voltage: 3-6S

I2C Connector: Support

BEC: 5V/2.5A

BEC: 10V/2.0A

Cam Input: Support

USART: UART1,UART2.UART3.UART4.UART6.UART7

Receiver: ELRS(CRSF).TBS(CRSF).SBUS.IBUS.DSM2.DSMX

GPS: YES

COMPASS: YES

HD O3: YES

ESC Signal: Dshoot150.Dshot300,Dshot600

USB: TYPE-C

Current Port: Yes.

Voltage Sensor: Yes

DFU Button: YES

FC firmware: betaflight_4.4.2_JHEF745.HEX

Instal hole: 30.5x30.5x4MM

Board size: 36x36MM

Weight: 7.5g

ESC

Input Power: 3-6S(11-27V)

Current: 60A

BEC: NO

Instal Hole: 30.5x30.5xM4

Size: 44x43MM

Firmware:BLHELI_32 JHEMCU_ESC32_MULTI_32_9.HEX

Weight: 15.4g

Includes

1x JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 60A 4in1 ESC) - Choose Version - MPU6000



JHEMCU F7 3-6S 30x30 Stack/Combo (GF30F745 FC / BL32 32Bit 60A 4in1 ES

Flywoo

Flywoo GOKU F405 ERVT 1-2S 5in1 AIO Flight Controller - 12A ESC, 2.4GHz ELRS, 400mW VTX

Flywoo has released another highly integrated AlO product, the GOKU Versatile F405 1-2S 12A5-in-1 400mw AlO with Built-in ELRS 2.4G. This remarkable AlO stands out as the world's firstto utilize the STM32F405 BGA chip while offering unrivaled integration capabilities. With 5UART serial ports, it facilitates seamless co

Flywoo GOKU F405 ERVT 1-2S 12A 5-in-1 400mw AIO with Built-in ELRS 2.4G - 25.5x25.5mm

The GOKU F405 ERVT AIO is an impressive 1-2S 12A 5-in-1 AIO with Built-in ELRS and a powerful 400mw VTX.&nbsp

The GOKU F405 ERVT AIO is an impressive 1-2S 12A 5-in-1 AIO with Built-in ELRS and a powerful 400mw VTX. 

Flywoo GOKU AIO - F405 ERVT FC + 12A 1-2S BLHeli_32 ESC + ELRS + VTX

FLYWOO

&ltp&gt&ltimg src&#x3D&quothttps://img-va.myshopline.com/image/store/2004172091/1673593876355/GOKU-Versatile-F405-2S-12A-5-in-1-400mw-AIO-(1)_1.jpeg?w&#x3D1600&ampamph&#x3D3922&quot alt&#x3D&quot&quot width&#x3D&quot1600&quot height&#x3D&quot3922&quot /&gt&ltimg src&#x3D&quothttps://img-va.myshopline.com/image/store/2004172091/1673593876355/GOKU-Versatile-F405-2S-12A-5-in-1-400mw-AIO-(2)_1.jpeg?w&#x3D1600&ampamph&#x3D5354&quot alt&#x3D&quot&quot width&#x3D&quot1600&quot height&#x3D&quot5354&quot /&gt&ltimg src&#x3D&quothttps://img-va.myshopline.com/image/store/2004172091/1673593876355/GOKU-Versatile-F405-2S-12A-5-in-1-400mw-AIO-(3).jpeg?w&#x3D1600&ampamph&#x3D7286&quot alt&#x3D&quot&quot width&#x3D&quot1600&quot height&#x3D&quot7286&quot /&gt&lt/p&gt

GOKU F405 ERVT 1-2S 12A 5-in-1 400mw AIO w/Bulit-in ELRS 2.4G

JHEMCU GF30F745 3-6S HD 30x30 Flight Controller

The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in port designed for HD VTXs like the DJI O3 Air Unit. 
Check out our other 30x30 FCs, and the rest of our JHEMCU selection!



Specifications

Chip: STM32F745VG(216MHZ)

Gyro: MPU6000

Barometer: DPS310

OSD Chip: AT7456E

Black box: 16MM

LED Program: Support

BB buzzer: Support

Input voltage: 3-6S

I2C Connector: Support

BEC: 5V/2.5A

BEC: 10V/2.0A

Cam Input: Support

USART: UART1,UART2.UART3.UART4.UART6.UART7

Receiver: ELRS(CRSF).TBS(CRSF).SBUS.IBUS.DSM2.DSMX

GPS: YES

COMPASS: YES

HD O3: YES

ESC Signal: Dshoot150.Dshot300,Dshot600

USB: TYPE-C

Current Port: Yes.

Voltage Sensor: Yes

DFU Button: YES

FC firmware: betaflight_4.4.2_JHEF745.HEX

Instal hole: 30.5x30.5x4MM

Board size: 36x36MM

Weight: 7.5g

Includes

1x JHEMCU GF30F745 3-6S 30x30 Flight Controller - MPU6000
4x grommets 


The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in po

JHEMCU GF30F745 3-6S HD 30x30 Flight Controller - MPU6000 from WREKD Co.

JHEMCU GF30F745 3-6S HD 30x30 Flight Controller - MPU6000

The JHEMCU GF30F745 3-6S 30x30 Flight Controller is ideal for drone pilots who demand high performance. It supports 3-6S and features advanced MPU6000 capabilities for smoother and more accurate flight. Enjoy an improved flying experience with this intuitive and reliable flight controller. Coming within 6pin plug in port designed for HD VTXs like the DJI O3 Air Unit.  Check out our other 30x30 FCs, and the rest of our JHEMCU selection!    Specifications  Chip: STM32F745VG(216MHZ)  Gyro: MPU6000  Barometer: DPS310  OSD Chip: AT7456E  Black box: 16MM  LED Program: Support  BB buzzer: Support  Input voltage: 3-6S  I2C Connector: Support  BEC: 5V/2.5A  BEC: 10V/2.0A  Cam Input: Support  USART: UART1,UART2.UART3.UART4.UART6.UART7  Receiver: ELRS(CRSF).TBS(CRSF).SBUS.IBUS.DSM2.DSMX  GPS: YES  COMPASS: YES  HD O3: YES  ESC Signal: Dshoot150.Dshot300,Dshot600  USB: TYPE-C  Current Port: Yes.  Voltage Sensor: Yes  DFU Button: YES  FC firmware: betaflight_4.4.2_JHEF745.HEX  Instal hole: 30.5x30.5x4MM  Board size: 36x36MM  Weight: 7.5g  Includes  1x JHEMCU GF30F745 3-6S 30x30 Flight Controller - MPU6000 4x grommets  

JHEMCU GF30F745-MPU 3-6S Flight Controller - 30x30mm Check out all our 30x30mm Flight Controllers and the rest of our JHEMCU Products!   Specifications: Chip:STM32F745VG(216MHZ) Gyro:MPU6000 Barometer:DPS310 OSD Chip:AT7456E Black box:16MM LED Program:Support BB buzzer:Support Input voltage:3-6S I2C Connector:Support B

JHEMCU GF30F745-MPU 3-6S Flight Controller - 30x30mm

Skystars

Skystars F722HD Pro 4 Flight Controller Stack - KM50A 50A ESC

Skystars F7HD Stack with 30x30 F722HD Pro4 Flight Controller &amp; KM50A 50A ESC! The flight controller Includes 6 UARTS, a 10V 3A Regulator for Caddx Vista or DJI Air Unit, and 8MB Blackbox! The flight controller also has convenient solder pads placed at each corner for easy wiring of LED's. The KM50A ESC is stable fo

Skystars F7HD Stack F722HD Pro 4 OSD & KM50A 50A ESC - 30 x 30mm

Skystars F7HD Pro 4 F722 Flight Controller

The new ﻿Skystars F722 HD Pro4 is a flight controller with a modern F7 processor. The fourth generation uses the MPU6000 gyro, has 16MB of blackbox memory, and both 5V/3A and 10V/3A BECs. The unit also has a connector for DJI Vista, Air Unit 03, or any FPV analog video transmission. The pads for connecting the LEDs are

Skystars F7HD Pro4 Flight Controller - 30x30mm

Skystars F7RS F722 Flight Controller

Skystars F7RS is a flight controller designed for racing and freestyle 5" drones. The flight controller is based on the F722 processor with a MPU6000 gyro. The FC also includes a 5V 3A BEC, OSD and 16MB of blackbox memory. The flight controller is protected against voltage spikes by a TVS diode. The main advantage of t

Skystars F7RS F722 FPV Drone Flight Controller - 20x20mm

Skystars F7RS Flight Controller Stack - MVP60A 60A 4in1 ESC

Skystars F7RS + MVP60 is a powerful stack designed for racing and freestyle 5" drones. At the heart of the flight controller is the F722 processor with MPU6000 gyro. The flight controller also includes a 5V 3A BEC, OSD and 16MB of blackbox memory. The ESCs support power from 3-6S Lipo batteries and can handle current u

Skystars F7RS Stack F722RS Flight Controller & MVP60A F4 Blheli_32 60A 3-6S 4in1 ESC - 20 x 20mm

BetaFPV

BetaFPV F4 2-3S AIO Flight Controller V1 - 20A ESC, 2.4GHz ELRS

BETAFPV












The BetaFPV V1 F4 2-3S AIO is the perfect choice for modern Whoop/Toothpick builds. Featuring an F4 AIO Flight Controller and 20A 4-in-1 ESC with ELRS serial, this setup guarantees smooth, consistent performance.  It features a dual BEC solution that delivers stable power outputs of 9V@2A for DJI O3 and 5V@3A for external devices. With a 20A ESC, it enables agile flight and increases dynamic. And connector for DJI O3 HD VTX and USB port for easy installation and maintenance. Ideal for HD VTX whoop enthusiasts, offering a heightened level of professionalism and convenience with this FC option.











Note: If you use the F4 2-3S 20A AIO FC V1, the serial port of the SBUS receiver is UART5Check out all our whoop flight controllers, and all our BetaFPV gear!
Features

Designed for HD VTX, it features a dual 9V@2A for DJI O3 and 5V@3A for external device BEC solution to prevent screen blackout on the DJI O3 due to low voltage during throttle increase.
It includes a new DJI O3 6-pin PMU for easy installation without soldering, reducing assembly complexity. Newbie friendly.
The power range of 2-3S provides increased thrust and improved control with a 20A ESC featuring a single NMOS for continuous current capability.
The upgraded onboard receiver allows selective power cutoff for saving power and offers additional UART TX3 and RX3 ports for connecting the external device.
The redesigned solder pad layout ensures larger, more secure pads for easy and reliable soldering, while the relocated USB port at the rear facilitates computer tuning.
It features an STM32F405RGT6 chip, Integrate Serial ELRS 2.4G receiver, 16M black box, barometer, current meter, reserve 3 complete serial ports and a standard SBUS, support GPS, HD VTX, external receiver, and other equipment.

F4 2-3S 20A AIO FC V1 also has extended the USB port to the end for easier parameter adjustment and wiring. And a new DJI O3 6-pin PMU has been added for convenient installation and maintenance.FAQPower cutoff: Removing the chip bead disconnects the power supply, and to reuse the onboard ELRS receiver, soldering the solder pads together restores power.UART3 release: Removing two resistors on the solder pads releases UART3. The left side is TX3, and the right side is RX3. To reconnect, solder the solder pads together when reusing the onboard ELRS receiver.Voltage Switch: The HD VTX connector defaults to 9V. The chip bead is soldered between the 9V pad and the middle pad. To use WalkSnail Avatar HD mini 1s and Lite, please ensure the power supply voltage is 5V. Remove the chip bead first from the 9V pad and solder it between the middle pad and the 5V pad. Alternatively, you can use solder instead the chip bead to switch between the 5V and 9V pads.Motor choice: Avoid selecting motors with excessively high KV ratings, as motors above 20,000KV are prone to burn.Betaflight Firmware and CLIFC firmware: Betaflight_4.4.1_BETAFVF405Download the firmware and CLI dump fileReference link:https://github.com/betaflight/betaflight/releases/tag/4.4.1ESC FirmwareWith BB51 ESC solution, F4 2-3S 20A AIO FC V1 is based on BLHeliSuite16714903 with Bluejay ESC firmware, it supports bidirectional D-shot and RPM filtering in Betaflight, offers 24KHz, 48KHz, and 96KHz fixed PWM frequency for options, and custom start-up melodies. F4 2-3S 20A AIO FC V1 default factory setting is 48KHz and it doesn’t recommend upgrading the 96KHz, or it might cause an error in the motor idle setting, not spinning when disarmed.DO NOT flash the firmware with a shorter interval, otherwise, there will be a certain chance of stalling and burning the flight controller.ESC-Configurator: https://preview.esc-configurator.com/Download BLHeliSuite16714903Download the Bluejay ESC firmware. Please choose C_X_70.HEXConnecting External DevicesPlease note that the board reserves two serial ports and a standard SBUS port, which is available for the external CRSF protocol receiver or GPS module, and SBUS protocol receiver. You can refer to the below picture.
Specifications

Weight: 5.58g (without motor connectors and power cable), 5.92g (with motor connectors)

Mounting Hole Size: 26mm x 26mm
CPU*: STM32F405RGT6 (168MHz)
Six-Axis: ICM42688P (SPI connection)
RX: Serial ELRS 2.4G Receiver
RX firmware version: BETAFPV AIO 2400 RX ELRS V2.5.2
Antenna: Enameled wire
Blackbox Memory: 16MB
Sensor: Barometer(BMP280),  Voltage&ampCurrent
5V BEC*: 5V 3A@8V supply
9V BEC*: 9V 2A@8V supply

USB Port: SH1.0 4-Pin
Built-in ESC with 20A continuous and peak 25A current
ESC input voltage: 2-3S
FC firmfware version: Betaflight_4.4.1_BETAFPVF405
ESC firmware: C_X_70_48_V0.19.2.hex for BB51 Bluejay hardware
Signal support: D-shot300, D-shot600

Includes

1x BetaFPV V1 F4 2-3S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bit 4in1 ESC) - ELRS Serial

Wiring Diagram 


 


The BetaFPV V1 F4 2-3S AIO is the perfect choice for modern Whoop/Toothpick builds. Featuring an F4 AIO Flight Controller and 20A 4-in-1 ESC with ELRS serial, this setup guarantees smooth, consistent performance.  It features a dual BEC solution that delivers stable power outputs of 9V@2A for DJI O3 and 5V@3A for exter

BetaFPV F4 20A V1 2-3S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bit 4in1 ESC) - ELRS 2.4GHz (UART)

BetaFPV F4 20A V1 2-3S AIO Whoop/Toothpick Flight Controller (w/ 20A 8

F4 2-3S 20A AIO FC V1 is specifically designed for HD VTX, utilizing 2-3S batteries for enhancing the flight experience. It features a dual BEC solution that delivers stable power outputs of 9V@2A for DJI O3 and 5V@3A for external devices. With a 20A ESC, it enables agile flight and increases dynamic. And connector for DJI O3 HD VTX and USB port for easy installation and maintenance. Ideal for HD VTX whoop enthusiasts, offering a heightened level of professionalism and convenience with this FC option.

Features

Designed for HD VTX, it features a dual 9V@2A for DJI O3 and 5V@3A for external device BEC solution to prevent screen blackout on the DJI O3 due to low voltage during throttle increase.
It includes a new DJI O3 6-pin PMU for easy installation without soldering, reducing assembly complexity. Newbie friendly.
The power range of 2-3S provides increased thrust and improved control with a 20A ESC featuring a single NMOS for continuous current capability.
The upgraded onboard receiver allows selective power cutoff for saving power and offers additional UART TX3 and RX3 ports for connecting the external device.
Redesigned solder pad layout ensures larger, more secure pads for easy and reliable soldering, while the relocated USB port at the rear facilitates computer tuning.
It features an STM32F405RGT6 chip, Integrate Serial ELRS 2.4G receiver, 16M black box, barometer, current meter, reserve 3 complete serial ports and a standard SBUS, support GPS, HD VTX, external receiver, and other equipment.

Specifications

Weight: 5.58g (without motor connectors and power cable),5.92g (with motor connectors)

Mounting Hole Size: 26mm x 26mm
CPU*: STM32F405RGT6 (168MHz)
Six-Axis: ICM42688P (SPI connection)
RX: Serial ELRS 2.4G Receiver
RX firmware version: BETAFPV AIO 2400 RX ELRS V2.5.2
Antenna: Enameled wire
Blackbox Memory: 16MB
Sensor: Barometer(BMP280),  Voltage&ampCurrent
5V BEC*: 5V 3A@8V supply
9V BEC*: 9V 2A@8V supply

USB Port: SH1.0 4-Pin
Built-in ESC with 20A continuous and peak 25A current
ESC input voltage: 2-3S
FC firmfware version: Betaflight_4.4.1_BETAFPVF405
ESC firmware: C_X_70_48_V0.19.2.hex for BB51 Bluejay hardware
Signal support: D-shot300, D-shot600

Includes

1 * F4 2-3S 20A AIO FC V1
4 * M2*10 Machine Screw 
4 * M2*10 Nylon Screw 
4 * M2 Nuts 
4 * Shock Absorbing Ball 
4 * JST1.25mm Angle Socket 
4 * JST1.25mm Straight Socket 
1 * SH1.0 4Pin Adapter Cable
1 * Type-C to SH1.0 Adapter 
1 * XT30 Power Cord
1 * Filter Capacitor 
1 * 30mm Double-head VTX connector wire 
1 * 60mm Single-head VTX connector wire

Wiring Diagram
Below is the diagram for F4 2-3S 20A AIO FC V1.



F4 2-3S 20A AIO FC V1 is specifically designed for HD VTX, utilizing 2-3S batteries for enhancing the flight experience. It features a dual BEC solution that delivers stable power outputs of 9V@2A for DJI O3 and 5V@3A for external devices. With a 20A ESC, it enables agile flight and increases dynamic. And connector for

F4 V1 2-3S 25x25 AIO Flight Controller with 8Bit 20A ESC and ELRS

F4 2-3S 20A AIO FC V1 is specifically designed for HD VTX, utilizing 2-3S batteries for enhancing the flight experience. It features a dual BEC solution that delivers stable power outputs of 9V@2A for DJI O3 and 5V@3A for external devices. With a 20A ESC, it enables agile flight and increases dynamic. And connector for DJI O3 HD VTX and USB port for easy installation and maintenance. Ideal for HD VTX whoop enthusiasts, offering a heightened level of professionalism and convenience with this FC option. Features Designed for HD VTX, it features a dual 9V@2A for DJI O3 and 5V@3A for external device BEC solution to prevent screen blackout on the DJI O3 due to low voltage during throttle increase. It includes a new DJI O3 6-pin PMU for easy installation without soldering, reducing assembly complexity. Newbie friendly. The power

F4 2-3S 20A AIO FC V1 is specifically designed for HD VTX, utilizing 2-3S batteries for enhancing the flight experience. It features a dual BEC solution that delivers stable power outputs of 9V@2A for DJI O3 and 5V@3A for external devices. With a 20A ESC, it enables agile flight and increases dynamic. And connector for

BetaFPV F4 2-3S 20A AIO FC V1 ELRS 2.4G Brushless Flight Controller

BetaFPV F4 20A V1 2-3S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bit 4in1 ESC) - ELRS 2.4GHz (UART) from WREKD Co.

SpeedyBee

SpeedyBee F405 V4 Flight Controller

Introducing the SpeedyBee F405 V4 flight controller with dual gyroscope power supply filtering, 4-level battery indicators, support for up to 8 motors, 4x LED strip soldering pads, 3A 5V &amp 9V BECs, and fixed SD card compatibility issue. Change motor direction wirelessly and quickly get set up with the DJI Air Unit plug-and-play set up. Plus, onboard barometer is included.












Features













User manual
Wireless FC &amp ESC full configuration
Dual gyroscope power supply filtering 

Onboard 4-level battery indicators
Supports up to 8 Motors 
4x LED strips soldering pads
5V &amp 9V BECs upgraded to 3A output
Fixed SD card compatibility issue
Change motor direction wirelessly 
DJI Air Unit plug-and-play

Built-in barometer














































Specifications
SpeedyBee F405 V4 30x30 Flight Controller

MCU: STM32F405

IMU(Gyro): ICM42688P

USB Port Type: Type-C

Barometer: Built-in

OSD Chip: AT7456E chip

BLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)

WIFI: Not supported

DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.

6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Blackbox MicroSD Card Slot: Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. 

Current Sensor Input: Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0.

Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)

5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.

9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.

3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output: Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.

UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

ESC Telemetry: UART R5(UART5)

I2C: Supported. SDA &amp SCL pads on front side. Used for magnetometer, sonar, etc.

Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.

Buzzer: BZ+ and BZ- pad used for 5V Buzzer

BOOT Button: Supported.[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input: Supported. Named as RS on the front side.

Smart Port / F.Port: Not supported

Supported Flight Controller Firmware: BetaFlight(Default), INAV

Firmware Target Name: SPEEDYBEEF405V4

Mounting: 30.5 x 30.5mm( 4mm hole diameter)

Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm

Weight: 10.5g


Includes

1x SpeedyBee F405 V4 3-6S 30x30 Flight Controller


 Wiring Diagram



Introducing the SpeedyBee F405 V4 flight controller with dual gyroscope power supply filtering, 4-level battery indicators, support for up to 8 motors, 4x LED strip soldering pads, 3A 5V &amp; 9V BECs, and fixed SD card compatibility issue. Change motor direction wirelessly and quickly get set up with the DJI Air Unit 

SpeedyBee F405 V4 3-6S 30x30 Flight Controller

SpeedyBee F405 V4 FC uses the STM32F405 chip (better than F411), onboard 4-level battery life indicator, 4GB Blackbox SD card slot for your flight logs, 4 groups of LED strip pads, complete with a DJI plug for your digital quad, and built-in Bluetooth for wireless configuration on the SpeedyBee app. * The DJI Air Unit 

SpeedyBee F405 V4 Flight Controller - 30x30mm

Speedybee

Introducing the SpeedyBee F405 V4 BLS 55A 30x30 FC&ampESC Stack – a high-performance flight controller and ESC combination that redefines value for money. Packed with top-shelf features, this stack offers exceptional performance at an unbeatable price of $69.99.Key Features:Powerful STM32F405 FC: Outclassing the F411, the STM32F405 FC ensures precise and responsive flight control.Onboard Battery Life Indicator: Stay informed with the 4-level battery life indicator, eliminating the need for additional tools.4GB Blackbox SD Card Slot: Capture and review your flight logs effortlessly with the onboard 4GB Blackbox SD card slot.DJI Plug Compatibility: Seamlessly connect your digital quad with the DJI plug, compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1.Built-in Bluetooth: Configure your setup wirelessly using the SpeedyBee app, enhancing user convenience.Robust 55A 4-in-1 ESC: The ESC features an aluminum alloy heat sink, TVS protective diode, Jap...

The best quality First Person View equipment. Free or discounted shipping on all orders.Drone Racing, RC Airplanes, FPV Cameras, FPV Goggles, Video Transmitters, RC Quads, Drone Antennas, Lipo Batteries, and Ground Station Equipment.All available for amateurs, schools, hobbyists, government, and wholesale buyers.

SpeedyBee F405 V4 BLS 55A 30x30 FC&ESC Stack - RMRC

SpeedyBee F405 V4 BLS 55A 30x30 FC&ampESC Stack

Elevate your drone's performance with the SpeedyBee F405 V4 Flight Controller, featuring STM32F405 MCU and ICM42688P gyro for precise control.&nbsp

Elevate your drone's performance with the SpeedyBee F405 V4 Flight Controller, featuring STM32F405 MCU and ICM42688P gyro for precise control. 

SpeedyBee F405 V4 Flight Controller - 30x30

RUNCAM

Introducing the SpeedyBee F405 V4 flight controller with dual gyroscope power supply filtering, 4-level battery indicators, support for up to 8 motors, 4x LED strip soldering pads, 3A 5V &amp 9V BECs, and fixed SD card compatibility issue. Change motor direction wirelessly and quickly get set up with the DJI Air Unit plug-and-play set up. Plus, onboard barometer is included.












Interested in the SpeedyBee F405 V4  BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC)?
Interested in the SpeedyBee BLS 8Bit 55A 3-6S 30x30 4in1 ESC?
Check out all our 30x30 stacks &amp combos, and all our Speedy Bee products!
Features














User manual
Wireless FC &amp ESC full configuration
Dual gyroscope power supply filtering 

Onboard 4-level battery indicators
Supports up to 8 Motors 
4x LED strips soldering pads
5V &amp 9V BECs upgraded to 3A output
Fixed SD card compatibility issue
Change motor direction wirelessly 
DJI Air Unit plug-and-play

Built-in barometer








































Specifications
SpeedyBee F405 V4 30x30 Flight Controller

MCU: STM32F405

IMU(Gyro): ICM42688P

USB Port Type: Type-C

Barometer: Built-in

OSD Chip: AT7456E chip

BLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)

WIFI: Not supported

DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.

6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Blackbox MicroSD Card Slot: Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. 

Current Sensor Input: Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0.

Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)

5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.

9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.

3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output: Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.

UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

ESC Telemetry: UART R5(UART5)

I2C: Supported. SDA &amp SCL pads on front side. Used for magnetometer, sonar, etc.

Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.

Buzzer: BZ+ and BZ- pad used for 5V Buzzer

BOOT Button: Supported.[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input: Supported. Named as RS on the front side.

Smart Port / F.Port: Not supported

Supported Flight Controller Firmware: BetaFlight(Default), INAV

Firmware Target Name: SPEEDYBEEF405V4

Mounting: 30.5 x 30.5mm( 4mm hole diameter)

Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm

Weight: 10.5g


Includes

1x SpeedyBee F405 V4 3-6S 30x30 Flight Controller


 Wiring Diagram



SpeedyBee F405 V4 3-6S 30x30 Flight Controller from WREKD Co.

SpeedyBee F405 V4 Flight Controller Stack - F405 FC, 55A 4in1 ESC

Richer features, unbelievable price!












The SpeedyBee F405 V4 BLS 3-6S 30x30 Stack/Combo is a powerhouse of features at a remarkably competitive price. It boasts a wireless FC &amp ESC configuration, dual gyroscope power supply filtering, onboard 4-level battery indicators, 8 motor support, 4x LED strips soldering pads, 3A output 5V &amp 9V BECs, fixed SD card compatibility issue, wireless motor direction change, a DJI Air Unit plug-and-play, and a built-in barometer. Get it now and enjoy an unparalleled performance!
The powerful 55A (70A burst) 4-in-1 ESC, built with aluminum alloy heat sink + TVS protective diode + Japan made TDK SMT capacitors + external 1000uF low ESR capacitor, everything is for a durable build and smooth flight.
All of that for only $69.99! Top-shelf spec at a crazy low price, what are you waiting for?
Interested in the SpeedyBee BLS 8Bit 55A 3-6S 30x30 4in1 ESC?
Interested in the SpeedyBee F405 V4 3-6S 30x30 Flight Controller?
Check out all our 30x30 stacks &amp combos, and all our Speedy Bee products!












Features

User manual
Wireless FC &amp ESC full configuration
ESC upgraded to 55A with heat sink 
Dual gyroscope power supply filtering 
Onboard 4-level battery indicators
Supports up to 8 Motors 
4x LED strips soldering pads
5V &amp 9V BECs upgraded to 3A output
Fixed SD card compatibility issue
Change motor direction wirelessly 
1000uF huge filtering capacitor 
DJI Air Unit plug-and-play
Built-in barometer









































Specifications
SpeedyBee F405 V4 30x30 Flight Controller

MCU: STM32F405

IMU(Gyro): ICM42688P

USB Port Type: Type-C

Barometer: Built-in

OSD Chip: AT7456E chip

BLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)

WIFI: Not supported

DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.

6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Blackbox MicroSD Card Slot: Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. 

Current Sensor Input: Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0.

Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)

5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.

9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.

3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output: Supported. Designed for a receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.

UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

ESC Telemetry: UART R5(UART5)

I2C: Supported. SDA &amp SCL pads on front side. Used for magnetometer, sonar, etc.

Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.

Buzzer: BZ+ and BZ- pad used for 5V Buzzer

BOOT Button: Supported.[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input: Supported. Named as RS on the front side.

Smart Port / F.Port: Not supported

Supported Flight Controller Firmware: BetaFlight(Default), INAV

Firmware Target Name: SPEEDYBEEF405V4

Mounting: 30.5 x 30.5mm( 4mm hole diameter)

Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm

Weight: 10.5g

SpeedyBee BLS 55A 30x30 4-in-1 ESC

Firmware: BLHeli_S J-H-40

Wireless Configuration: Full Configuration Supported in the SpeedyBee app

PC Configurator Download Link: https://esc-configurator.com/
Continuous Current: 55A x 4
Burst Current: 70(10 seconds)
TVS Protective diode: Yes
External Capacitor: 1000uF Low ESR Capacitor(In the package)
ESC Protocol: DSHOT300/600
Power Input: 3-6S LiPo
Power Output: VBAT
Current Sensor: Support (Scale=400 Offset=0)
ESC Telemetry: Not supported
Mounting: 30.5 x 30.5mm( 4mm hole diameter)
Dimension: 45.6(L) x 44(W) x 8mm(H)
Weight: 23.5g

Includes

1x SpeedyBee F405 V4  BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC)


 Wiring Diagram




Richer features, unbelievable price! The SpeedyBee F405 V4 BLS 3-6S 30x30 Stack/Combo is a powerhouse of features at a remarkably competitive price. It boasts a wireless FC &amp; ESC configuration, dual gyroscope power supply filtering, onboard 4-level battery indicators, 8 motor support, 4x LED strips soldering pads, 

SpeedyBee F405 V4  BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC) from WREKD Co.

SpeedyBee F405 V4  BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC)

With only $69.99, you will get an STM32F405 FC (better than F411), onboard 4-level battery life indicator, 4GB Blackbox SD card slot for your flight logs, 4 groups of LED strip pads, complete with a DJI plug for your digital quad, and built-in Bluetooth for wireless configuration on the SpeedyBee app. Don't forget abou

SpeedyBee F405 V4 Stack w/ 55A 3-6S BLS 4in1 ESC - 30x30mm

Elevate your drone's performance with the SpeedyBee F405 V4 Stack, featuring STM32F405 MCU and ICM42688P gyro for precise control.&nbsp

Elevate your drone's performance with the SpeedyBee F405 V4 Stack, featuring STM32F405 MCU and ICM42688P gyro for precise control. 

SpeedyBee F405 V4 Stack - F4 V4 FC + 55A BLHeli_S ESC - 30x30

Richer features, unbelievable price!












The SpeedyBee F405 V4 BLS 3-6S 30x30 Stack/Combo is a powerhouse of features at a remarkably competitive price. It boasts a wireless FC &amp ESC configuration, dual gyroscope power supply filtering, onboard 4-level battery indicators, 8 motor support, 4x LED strips soldering pads, 3A output 5V &amp 9V BECs, fixed SD card compatibility issue, wireless motor direction change, a DJI Air Unit plug-and-play, and a built-in barometer. Get it now and enjoy an unparalleled performance!
The powerful 55A (70A burst) 4-in-1 ESC, built with aluminum alloy heat sink + TVS protective diode + Japan made TDK SMT capacitors + external 1000uF low ESR capacitor, everything is for a durable build and smooth flight.
All of that for only $69.99! Top-shelf spec at a crazy low price, what are you waiting for?
 












Features

User manual
Wireless FC &amp ESC full configuration
ESC upgraded to 55A with heat sink 
Dual gyroscope power supply filtering 
Onboard 4-level battery indicators
Supports up to 8 Motors 
4x LED strips soldering pads
5V &amp 9V BECs upgraded to 3A output
Fixed SD card compatibility issue
Change motor direction wirelessly 
1000uF huge filtering capacitor 
DJI Air Unit plug-and-play
Built-in barometer









































Specifications
SpeedyBee F405 V4 30x30 Flight Controller

MCU: STM32F405

IMU(Gyro): ICM42688P

USB Port Type: Type-C

Barometer: Built-in

OSD Chip: AT7456E chip

BLE Bluetooth: Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)

WIFI: Not supported

DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.

6-pin DJI Air Unit Plug: Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Blackbox MicroSD Card Slot: Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. 

Current Sensor Input: Supported. For SpeedyBee BLS 55A ESC, please set scale = 400 and Offset = 0.

Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)

5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.

9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.

3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.

4.5V Output: Supported. Designed for a receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.

UART: 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

ESC Telemetry: UART R5(UART5)

I2C: Supported. SDA &amp SCL pads on front side. Used for magnetometer, sonar, etc.

Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.

Buzzer: BZ+ and BZ- pad used for 5V Buzzer

BOOT Button: Supported.[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input: Supported. Named as RS on the front side.

Smart Port / F.Port: Not supported

Supported Flight Controller Firmware: BetaFlight(Default), INAV

Firmware Target Name: SPEEDYBEEF405V4

Mounting: 30.5 x 30.5mm( 4mm hole diameter)

Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm

Weight: 10.5g

SpeedyBee BLS 55A 30x30 4-in-1 ESC

Firmware: BLHeli_S J-H-40

Wireless Configuration: Full Configuration Supported in the SpeedyBee app

PC Configurator Download Link: https://esc-configurator.com/
Continuous Current: 55A x 4
Burst Current: 70(10 seconds)
TVS Protective diode: Yes
External Capacitor: 1000uF Low ESR Capacitor(In the package)
ESC Protocol: DSHOT300/600
Power Input: 3-6S LiPo
Power Output: VBAT
Current Sensor: Support (Scale=400 Offset=0)
ESC Telemetry: Not supported
Mounting: 30.5 x 30.5mm( 4mm hole diameter)
Dimension: 45.6(L) x 44(W) x 8mm(H)
Weight: 23.5g

Includes

1x SpeedyBee F405 V4  BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 55A 4in1 ESC)


 Wiring Diagram




KISS

KISS Ultra Mini V2 Flight Controller

We are extremely happy to be an official retailer for the fan favorite KISS Ultra V2! The Anuta Software KISS Ultra Mini V2 features the latest STM32H743 processor. Providing unparalleled processing power to your aircraft. Along with an IIM-42652 SPI gyro, 5v 2A BEC, 6-27V (2-8S) power handling, and a host of other fea

KISS Ultra Mini V2 FPV Drone Flight Controller - 20x20mm

GEPRC TAKER F405 Flight Controller Stack - 50A 4in1 ESC

The GEPRC TAKER Stack - F405 FC+ 50A 3-6S BLHeli_S ESC is a plug-and-play system designed for the DJI Air Unit.

GEPRC TAKER Stack - F405 FC+ 50A 3-6S BLHeli_S ESC

GEPRC TAKER F405 BLS 50A STACK is a plug-and-play stack system specially designed for DJI Air Unit. Use STM32F405 chip, ICM42688-P gyroscope, integrated 16M black box, and GEP-BLS50A-4IN1 ESC to have a more delicate hand feeling experience. The GEPRC TAKER F405 BLS 50A STACK can be directly plugged into the DJI Air Uni

GEPRC TAKER F405 Stack with BLS 50A 4in1 ESC - 30*30mm

Summary
GEPRC TAKER F405 BLS 50A STACK is a plug-and-play stack system specially designed for DJI Air Unit. Use STM32F405 chip, ICM42688-P gyroscope, integrated 16M black box, and GEP-BLS50A-4IN1 ESC to have a more delicate hand feeling experience.

The GEPRC TAKER F405 BLS 50A STACK can be directly plugged into the DJI Air Unit, which can save the trouble of soldering. Upgrade the type-C USB connector, which greatly improves the service life of the socket and reduces the risk of poor contact. 9V 2.5A + 5V 3A dual independent BEC, more stable power supply for external devices.
Features

 	Use mainstream STM32F405 chip
 	Equipped with the latest 42688-P gyroscope
 	16M black box storage
 	Integrated LC filter
 	Upgrade type-C USB interface
 	Directly plugged into the DJI Air Unit
 	With GEP-BLS50A-4IN1 ESC, the flying feel is silky
 	Simple and reasonable installation method, the shock absorber can make the gyroscope work very stably
 	9V 2.5A + 5V 3A dual independent BEC

Specifications
GEP-F405-HD v2 Flight Controller

 	MCU: STM32F405
 	IMU: ICM42688-P(SPI)
 	Air Unit Connection: Direct plugging into DJI Air Unit
 	Black Box: 16M onboard
 	USB Connector: Type-C
 	OSD: BetaFlight OSD w/ AT7456E chip
 	BEC: 5V,9V dual BEC
 	Firmware Target: GEPRCF405
 	Size: 36.8x36.8mm, hole 30.5x30.5mm，φ4mm hole becomes φ3mm after using a silicone shock-absorbing circle.
 	Input Voltage: 3-6S LiPo
 	UART: 6
 	Power Filter: Integrated LC filter
 	Weight: 7.7g

GEP-BLS50A-4IN1 ESC

 	Input Voltage: 3-6S Lipo
 	Galvanometer: Support
 	Continuous Current: 50A
 	Burst Current: 55A（5s）
 	Support Protocol: Oneshot125/Oneshot42/Mulishot modes/Dshot 150/300/600
 	Size: 42.9x39.7mm, hole30.5x30.5mm，φ4mm hole becomes φ3mm after using the silicone shock-absorbing circle.
 	Weight:13.7g
 	Target: G_H_30

Includes
1 x Flight Controller
1 x ESC
1 x Capacitor
1 x DJI Air Unit Adapter Cable
1 x Flight Controller Adapter Cable
1 x XT60 Power cable
4 x M3*30 Screws
4 x M3*24 Screws
8 x Nylon nuts
8 x Silicone grommets
2 x sh1.0 4pinsilicone cable
1 x Camera connection cable

Summary GEPRC TAKER F405 BLS 50A STACK is a plug-and-play stack system specially designed for DJI Air Unit. Use STM32F405 chip, ICM42688-P gyroscope, integrated 16M black box, and GEP-BLS50A-4IN1 ESC to have a more delicate hand feeling experience. The GEPRC TAKER F405 BLS 50A STACK can be directly plugged into the DJI Air Unit, which [...]

GEPRC TAKER F405 BLS 50A Stack - GEPRC

GEPRC TAKER F405 BLS 50A Stack

Introducing GEPRC's take on the best budget stack out there on the market!
GEPRC TAKER F405 BLS 50A STACK is a plug-and-play stack system specially designed for DJI Air Unit. With the STM32F405 chip, ICM42688-P gyroscope, 16M black box and GEP-BLS50A-4IN1 ESC, you can enjoy a smooth and effortless user experience. This stack system connects to the DJI Air Unit with no soldering required, plus the upgraded Type-C USB connector increases the lifespan of the socket and reduces the risk of poor contact. The 9V 2.5A + 5V 3A dual independent BEC ensures a reliable power supply for any external device you might need.
Check out all our 30x30 stacks &amp combos, as well as the rest of our GEPRC selection.

Features


Use mainstream STM32F405 chip
Equipped with the latest 42688-P gyroscope
16M black box storage
Integrated LC filter
Upgrade type-C USB interface
Directly plugged into the DJI Air Unit
With GEP-BLS50A-4IN1 ESC, the flying feel is silky
A simple and reasonable installation method, the shock absorber can make the gyroscope work very stably
9V 2.5A + 5V 3A dual independent BEC








Specifications
GEP-F405-HD V2 Flight Controller

MCU: STM32F405
IMU: ICM42688-P(SPI)
Air Unit Connection: Direct plugging into DJI Air Unit
Black Box: 16M onboard
USB Connector: Type-C
OSD: BetaFlight OSD w/ AT7456E chip
BEC: 5V,9V dual BEC
Firmware Target: GEPRCF405
Size: 36.8×36.8mm, hole 30.5×30.5mm，φ4mm hole becomes φ3mm after using a silicone shock-absorbing circle.
Input Voltage: 3-6S LiPo
UART: 6
Power Filter: Integrated LC filter
Weight: 7.7g

GEP-BLS50A-4IN1 ESC

Input Voltage: 3-6S Lipo
Galvanometer: Support
Continuous Current: 50A
Burst Current: 55A（5s）
Support Protocol: Oneshot125/Oneshot42/Mulishot modes/Dshot 150/300/600
Size: 42.9×39.7mm, hole30.5×30.5mm，φ4mm hole becomes φ3mm after using the silicone shock-absorbing circle.
Weight:13.7g
Target: G_H_30

Includes


1x Flight Controller


1x ESC


1x Capacitor


1x DJI Air Unit Adapter Cable


1x Flight Controller Adapter Cable


1x XT60 Power cable


4x M3x30 Screws


4x M3x24 Screws


8x Nylon nuts


8x Silicone grommets


2x sh1.0 4pinsilicone cable

1x Camera connection cable


Introducing GEPRC's take on the best budget stack out there on the market! GEPRC TAKER F405 BLS 50A STACK is a plug-and-play stack system specially designed for DJI Air Unit. With the STM32F405 chip, ICM42688-P gyroscope, 16M black box and GEP-BLS50A-4IN1 ESC, you can enjoy a smooth and effortless user experience. This